Smartech TECH-5000P User manual

User Guide
Guía del usuario
Smartech TECH-5000P Power Kit
Kit de alimentación Smartech TECH-5000P
Model/Modelo TECH-5000P
CAUTION:
Read and follow all safety
rules and operating instructions
before every use of this product.
SAVE THESE INSTRUCTIONS.
ATENCIÓN:
Lea y siga todas las reglasde
seguridad e instrucciones de uso
antes de cada uso de este producto.
GUARDE ESTAS INSTRUCCIONES.

USER’S MANUAL PAGE 2TECH-5000P
SAFETY INFORMATION
1. Avoid dangerous environments. Do not charge this item in rain,
snow, damp or wet environments.
2. Do not use this item or charger in the presence of explosive
atmospheres (gaseous fumes, dust or ammable materials)
since sparks may be generated when attaching or removing
FULLY CHARGE IMMEDIATELY AFTER PURCHASE
Fully recharge after each jumpstarting, or every 3 months to ensure
long battery life.
What’s included with the Smartech TECH-5000P Power Kit

USER’S MANUAL PAGE 3TECH-5000P
3. Charge in a well-ventilated area. Do not allow smoking or open
ames near a charging battery. Vented gases may explode.
4. Do not burn or incinerate this item. This item may explode,
causing personal injury or damage. Toxic fumes and materials
are created when batteries are burned.
5. Do not crush, drop, or damage this item.
6. Do not use this item or a battery charger that has received a
sharp blow, been dropped, run over or damaged in any way
(e.g. pierced with a nail, hit with a hammer or stepped on).
7.WARNING: Do not disassemble. Disassembly may result in
the risk of electric shock, re or exposure to battery chemicals.
8. Battery chemicals cause serious burns. Never allow contact
with skin, eyes, or mouth. If this item leaks battery chemicals,
use rubber or neoprene gloves to dispose of it. If skin is
exposed to battery uids, wash with soap and water and
rinse with vinegar. If eyes are exposed to battery chemicals,
immediately ush with water for 20 minutes and seek medical
attention. Remove and dispose of contaminated clothing.
9. Do not short circuit. This item will short circuit if a metal object
makes connection to the power cable port. Do not place this
item near anything that may cause a short circuit, such as
coins, keys, or nails. A shortcircuited battery may cause re
and personal injury.
10. When jump starting your vehicle do not place Jump Starter on
the ground or at a height less than 18 inches.
11. Never charge or jump start a frozen battery. Store this item and
charger in a cool dry place.
12. Do not store this unit for more than 10 days where tempera-
tures may exceed 120 degrees F (50 degrees C) such as in
direct sunlight, a vehicle, or metal building during the summer
as it may cause damage it the unit.

USER’S MANUAL PAGE 4TECH-5000P
TECH-5000P POWER BANK / JUMP STARTER
The Power Bank / Jump Starter features a low voltage protection
(for Power Bank / Jump Starter itself), spark proof, reverse polarity
13. This product is intended for private use only and should not
be used in any commercial applications. Use of this product to
start multiple vehicles over a short period of time may damage
the Jump Starter / Charger.
14. WARNING: Before attempting to start a vehicle, be sure the
blue plug of the Smart Jumper Cable is rmly secured into
the Smart Jumper Cable Input Socket and be sure that the
battery clamps have a good connection with the proper battery
terminals. Clean rusted or dirty terminals before attempting to
jumpstart the vehicle.
15. WARNING: Remove the jump starter form the vehicle battery
within 30 seconds of successfully restarting. To do so, remove
the Smart Jumper Cables from the Jump Starter. Then remove
the Smart Jumper Cables from the battery terminals.
16. WARNING: Only use the provided charging cords with this
product.
17. WARNING: Disposal of this Device. This device contains a non
replaceable Lithium Polymer battery. It is not user replaceable.
Battery must be disposed of properly when it no longer holds a
charge. This product should be recycled or disposed of as per
state and local guidelines
18. WARNING: This product is not a toy and is not intended for
use by children.
19. PROPOSITION 65 WARNING: This product contains
chemicals known to the state of California to cause cancer and
birth defects or other reproductive harm (California law requires
this warning to be given to customers in the state of California).

USER’S MANUAL PAGE 5TECH-5000P
TECHNICAL SPECIFICATIONS:
Battery Type Lithium-ion Polymer
Battery Capacity 44.4WH
Starting Current 250A
Peak Current 500A
Jump Start up to 5.5L Gas Engine
USB Output 5V/2.4A, 5V/2.4A
LED Flashlight 1W
19V Output 19V/3.5A for Laptops
12V Output 10A Max
Operating Temperature -22˚F ~ +122˚ F
Charging Temperature 32˚F ~ +104˚F
Storage Temperature -4˚F ~ +95˚F (for 3 months)
protection and short circuit protection. This Power Bank / Jump
Starter can instantly jump start most single battery vehicles, up
to 60+ (over 60) times on a full charge. The Power Bank / Jump
Starter is also equipped with USB power output, LED ashlight,
19VDC power output and 12VDC power output.

USER’S MANUAL PAGE 6TECH-5000P
PRODUCT FEATURES AND LAYOUT
EC5
ENGINE START
Socket
LCD
15V/1A
Input Port
19V
Output
12V
Output Port
USB Output
Ports
Flashlight
Button
Power
Button

USER’S MANUAL PAGE 7TECH-5000P
LCD DISPLAY
1 2 3 4 5 6
7 8 9
1. 15V/1A input
2. 5V/2.4A output
3. Light steady on
4. Light FLASH
5. 5V/2.4A output
6. Light SOS
7. Battery capacity
8. 12V output
9. 19V output
CHARGING THE LITHIUM ION POWERBANK
This product is partially charged from the manufacturer. Fully
charge the unit immediately after purchase. In order to prolong
the product life, be sure to fully recharge the unit after each
jumpstarting, or every 3 months even if this unit has not been used.
If battery voltage in the TECH-5000P Power Kit is too low, the
unit will shut off to prevent damage to itself. Recharge as soon as
possible to be activated and fully charge it to ensure long battery
life. In addition, it is not recommended to charge and discharge
(use) the Power Bank at the same time.
CHARGING OPTION 1:
Plug one end of the wall charger cord into the 15V/1A Input
port of the Lithium Ion Powerbank and plug the other end of
the wall charger cord into a standard wall outlet. (See detailed
diagram on the following page.)

USER’S MANUAL PAGE 8TECH-5000P
TECH-5000P
Power Bank
15V/1A Input
Charging Port
Option 1
Wall Charger
Wall Outlet
Option 2
12V Car
Charger Car Cigarette lighter
CHARGING OPTION 2:
Plug one end of the 12V car charger cord into the 15V/1A Input
port of the Lithium Ion Powerbank and plug the other end of the
12V car charger cord to your car cigarette lighter. (See detailed
diagram below.)

USER’S MANUAL PAGE 9TECH-5000P
JUMP START YOUR VEHICLE BATTERY USING THE
TECH-5000P POWER BANK
CONNECT TO BATTERY
1. Identify polarity of battery posts. The positive battery terminal
is typically marked by these letters or symbol (POS,P,+). The
negative battery terminal is typically marked by these letters or
symbol (NEG,N,-).
2. Do not make any connections to the carburetor, fuel lines, or
thin metal parts.
3. Identify if you have a negative or positive grounded vehicle.
This can be done by identifying which battery post (NEG or
POS) is connected to the chassis.
4. For a negative grounded vehicle (most common): connect
the RED POSITIVE jumper clamp rst to the positive battery
terminal, then connect the BLACK NEGATIVE jumper clamp to
the negative battery terminal or vehicle chassis.
5. For a positive grounded vehicle (very uncommon): connect the
BLACK NEGATIVE jumper clamp rst to the negative battery
terminal, then connect the RED POSITIVE jumper clamp to the
positive battery terminal or vehicle chassis.
6. When disconnecting, disconnect in the reverse sequence,
removing the negative rst (or positive rst for positive ground
systems).

USER’S MANUAL PAGE 10TECH-5000P
Red
LED
BOOST
Button
EC5
Plug
Negative
Clamp
Positive
Clamp
Green
LED
12 Volt
Vehicle
Battery
+
-
TECH-5000P
Power Bank
Pull rubber tab to open
ENGINE START
socket
Vehicle Battery Connection

USER’S MANUAL PAGE 11TECH-5000P
JUMP STARTING PROCEDURE
1. This unit is only for emergency use, not for frequent commercial
use! ENGINE START socket is ALWAYS activated! Do not attempt
to jumpstart your vehicle when the TECH-5000P Power Bank
battery capacity is below 30%.
2. Turn off the vehicle ignition and all accessories (radios, lights, air
conditioners, etc.), and disconnect electronic devices.
3. Connect the jumper clamps to the correct polarity battery terminals
as per item 3 in the previous CONNECT TO BATTERY section.
4. Connect the EC5 plug of jumper cables to the ENGINE START
socket of Power BANK. If the Green LED doesn’t turn on use
BOOST. Refer to the BOOST OPERATION section.
5. Try starting the vehicle (turn on the ignition switch). Most vehicles
will immediately start. Stop if the vehicle does not start after
5 seconds of engine cranking. The jumpstart feature is designed
for short term operation only, and more than 5 seconds may cause
damage to the unit. Allow the jump starter to cool down for at least 3
minutes after each jumpstarting.
6. Disconnect the cable from the Power Bank immediately after
engine starts, and then remove from battery terminals.

USER’S MANUAL PAGE 12TECH-5000P
“BOOST” OPERATION:
1. Connect the Jump Starter to the vehicle battery (Red LED
keeps on and green LED is off), press and hold BOOST button
for 3 seconds (after a buzzer sound, the green LED is on and
red LED is off). “BOOST” is used when the vehicle battery
capacity is low.
2. Start the engine (same method as the normal operations on
Page 9).
Cautions:
1. Under normal circumstances, do not use BOOST. Use only
when the vehicle battery capacity is low.
2. The spark proof, reverse polarity protection and short circuit
protection features are disabled after BOOST button is
pressed. Pay very close attention to the polarity of the battery
before using this mode. Do not allow the positive and negative
battery clamps to touch or connect to each other as the item
will generate sparks and high heat if not used properly.
SMART BATTERY CLAMP AUDO/VISUAL INDICATOR:
No. Red LED Green
LED
Buzzer
Sound Condition
1 On Off One sound Jumper cables and jump
starter are connected.
Ready for connection to
vehicle battery.
2Off On One sound Jumper cable and vehicle
battery are connected.
Ready to start the engine.

USER’S MANUAL PAGE 13TECH-5000P
3Slow ash Off No buzzer Lithium battery voltage in
the TECH-5000P Power
Kit is rather low.
4Slow ash Off No buzzer Have not turned on the
ignition switch within the
regulated time. To resolve
this, you need remove
clamps from vehicle bat-
tery, and connect again.
5Fast ash Off Fast buzzer Red and black clamps are
connected with each other.
6Fast ash Off Fast buzzer Reverse connection of
clamps.
7Off Fast ash No buzzer Engine is started.
8Off Fast ash No buzzer Vehicle’s battery volt-
age is higher than Jump
Starter’s.
USB POWER
Connect the USB device to the TECH-5000P Power Bank with the
included multi-tip cable (For Apple® for Apple® products, it’s
better to use the original cable that came with the devise). Press
the Power Button to start USB power, and press Power button
to quit. When disconnected, the TECH-5000P Power Bank will
automatically shut off. The number of times you can recharge a
USB device will vary between devices.
FLASHLIGHT
Press Flashlight button to start ashlight. Press once to switch
lighting modes: Steady On – Strobe – SOS – Off.

USER’S MANUAL PAGE 14TECH-5000P
SUPPLY TO 19V LAPTOPS
The TECH-5000P Power Bank can run/charge computer laptops.
Using the included accessory cord, select the appropriate input tip
and connect the TECH-5000P Power Bank to your laptop. Press
Power / Flashlight button to start 19V/3.5A power, and press Power
button to quit. When disconnected, the TECH-5000P Power Bank
will automatically shut off. The number of times you can recharge a
laptop will vary between devices.
See detailed diagram below
19V Laptop
Input
Adapter
Tips
(If needed)
Adapter
Cord
TECH-5000P
Power Bank
19V Output
for powering
Laptops

USER’S MANUAL PAGE 15TECH-5000P
SUPPLY TO 12V APPLIANCES
The TECH-5000P Power Bank can run/charge 12VDC appliances
that draw 10 amps or less. Two Options as follows:
USING THE 12V ADAPTER
Connect the TECH-5000P Power Bank to a 12V appliance
with the included 12V adapter accessory. You don’t need to
press the power button as the Power Bank output is ALWAYS
activated. When battery voltage of TECH-5000P Power Bank
is too low, 12V appliances will stop running/charging.
EC5
Plug
12 Volt
Adapter
TECH-5000P
Power Bank
Pull rubber tab to open
ENGINE START
socket
See detailed diagram below

USER’S MANUAL PAGE 16TECH-5000P
USING THE 12V CONNECTOR CORD
Connect the TECH-5000P Power Bank to a 12V appliance
using the included accessory cord and adapter tip. Press
Power / Flashlight button to start 12V power, and press Power
button to quit. When disconnected, the TECH-5000P Power Kit
will automatically shut off.
Any device
with a 12V
input Adapter
Cord
TECH-5000P
Power Bank
12V output
for powering
12V device
See detailed diagram below

USER’S MANUAL PAGE 17TECH-5000P
TECH-5000P AIR PUMP
LAP-3 Specication:
Working Voltage:12V DC
Current: 3.5A
Peak Current: ≤7A
Ination Efciency: 185/65R14 (Tire) to 35PSI in 5minutes
Maximum Gas Pressure: 150PSI
Hose Length: 5.31 inches (135mm)
Working Temperature: -4˚F ~ 140˚F (-20˚C~+60˚C)
Dimension: 2.44 X 7.16 X 8.90 inches (62mm X 182mm X 226mm)
Weight: 1.37 lbs (620g)

USER’S MANUAL PAGE 18TECH-5000P
IMPORTANT SAFETY INSTRUCTIONS FOR THE
TECH-5000P POWER KIT (AIR PUMP)
WORK AREA SAFETY
1. Keep your work area clean and well lit. Cluttered areas invite
accidents.
2. Keep bystanders, children, and visitors away while operating
an air pump. Distractions can cause you to lose control.
3. Operate air pump in an open area at least 18 in. away from any
wall or object that could restrict the ow of fresh air to
ventilation openings.
ELECTRICAL SAFETY
1. To reduce the risk of electrical shock, do not put air pump in
water or other liquid. Do not place or store appliance where it
can fall or be pulled into a tub or sink. Keep others away while
operating the air pump. Distractions can cause you to lose
control.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense
when operating an air pump. Do not use air pump while tired or
under the inuence of drugs, alcohol, or medication. A moment
of inattention while operating air pump may result in serious
personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain
long hair. Keep your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
3. Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enable better control of the

USER’S MANUAL PAGE 19TECH-5000P
air pump in unexpected situations.
4. Use safety equipment. Always wear eye protection. Dust mask,
non-skid safety shoes, hard hat, or hearing protection must be
used for appropriate condition.
5. Eye protection is required to guard against ying fasteners and
debris which could cause severe eye injury.
6. Do not wear loose clothing or jewelry. Contain long hair. Loose
clothes, jewelry, or long hair can be drawn into air vents.
7. Do not use on a ladder or unstable support. Stable footing on a
solid surface enables better control of the air pump in
unexpected situations.
8. Do not disassemble the air pump.
9. Do not operate air pump near ammable liquids or in gaseous
or explosive atmospheres. Internal sparks may ignite fumes.
10. Do not store your air pump in a damp or wet location. Do not
store in locations where the temperature is less than 50˚F or
more than 100˚F.
AIR PUMP USE AND CARE
1. Check hose for weak or worn condition before each use,
making certain all connections are secure. Do not use if defect
is found. Purchase a new hose or notify an authorized service
center for examination or repair.
2. Release all pressures within the system slowly. Dust and
debris may be harmful.
3. Do not use air pump if switch does not turn it on or off. An
air pump that cannot be controlled with the switch is dangerous
and must be repaired.
4. Store idle air pumps out of reach of children and other
untrained persons. Air pumps are dangerous in the hands of
untrained users.

USER’S MANUAL PAGE 20TECH-5000P
5. Check for misalignment or binding of moving parts, breakage
of parts, and any other condition that may affect the air pump’s
operation If damaged, have the air pump serviced before
using. Many accidents are caused by poorly maintained tools.
6. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one air pump may create a risk of injury when used
on another air pump.
7. Keep the air pump and its handle dry, clean and free from oil
and grease. Always use a clean cloth when cleaning. Never
use brake uids, gasoline, petroleum-based products, or any
strong solvents to clean your air pump. Following this rule
will reduce the risk of loss of control and deterioration of the
enclosure plastic.
8. Never point any air pump toward yourself or others.
9. Keep the exterior of the air pump dry, clean, and free from oil
and grease. Always use a clean cloth when cleaning. Never
use brake uids, gasoline, petroleum-based products, or any
strong solvents to clean the unit. Following this rule will reduce
the risk of deterioration of the enclosure plastic.
10. Do not exceed the pressure rating of any component in the
system.
11. Protect material lines and air lines from damage or puncture.
Keep hose and power cord away from sharp objects, chemical
spills, oil, solvents, and wet oors.