SMARTPOINT SPSSPATHLTS-2PK User manual

For more products please visit www.smartpointco.com
FCC ID: 2ANDL-BT3L
SmartSolar
Pathway Lights
USER MANUAL

For more products please visit www.smartpointco.com
FCC Statement:
1. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
2. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20cm between
the radiator and any part of your body.

For more products please visit www.smartpointco.com
SPECIFICATIONS
Model: SPSSPATHLTS-2PK
Lamp Source: 1 warm white LED 2700K,
1 cool white LED 7000K, 1 color changing LED
Battery Capacity: 600mAh(Li-) rechargeable
Lumens: 15 at normal white
Lamp Color: RGBW
Battery Voltage: 3.7V
Protocol: Bluetooth Mesh
Solar Panel: 0.4W/5V poly crystalline solar panel
Control Distance: 60-85 feet(with no obstacles in way)
IP Rating: IP44
Operating Temperature: -4°F ~ 122°F
WARRANTY INFORMATION
One Year Limited Warranty.
Customer Service: 732-994-2301; email: [email protected]
©Smartpoint LLC,
250 Liberty Street, Suite 1A
Metuchen, NJ 08840
Manufactured, marketed and distributed by Smartpoint LLC, under license.
Google and Google Play are trademarks of Google LLC.
App Store
®
is a registered trademark of Apple, Inc.
All trademarks and registered trademarks are property of their respective owners.
Made in China

FEATURES
• Bluetooth remote controlled
• Changes to any color or white
• Dimmable
• Syncs with music
• Light Sensor - automatically turns on when dark
and turns off when light
• Rechargeable battery that recharges from
the solar panel
• Weatherproof

PRODUCT CONFIGURATION
Solar Panel/Light Sensor
Stake
Light
On/Off Button

DOWNLOAD APP
1. Android™: download “Smartpoint Home” app
on Google Play.
2. iPhone: download “Smartpoint Home” app
from the App Store.
Smartpoint Home

REGISTRATION AND LOGIN
1. Run the “Smartpoint Home” app from your
smart phone.
2. Sign up and login.
*Screenshots may slightly differ from actual app.
*

ADD DEVICE
1. Make sure Bluetooth is turned on in your
phone’s settings.
2. Unscrew the top of the light. Remove the
pull-tab,find the power button and turn the
light on and off 5-6 times and then leave it
on. (If light does not turn on it may need to
be charged. Place in sunlight to charge.
Light takes about 6-8 hours of sunlight to
fully charge)
3. Then on the home screen of the app, press
the (+) in the top right corner or “Add Device”
in the middle.
4. Once you are on the page with all the
devices to add, wait a few seconds and a
window to add the device will pop up..
When device window pops up with the light
to add, press “Go to add”
NOTE
(During set up process, cover the light sensor or
turn light upside down so light thinks it is dark)

5. On the next screen press the (+) symbol to
begin adding the Solar Light.
6. Connecting process will begin. Do not turn
off Solar Light while connecting. Wait for
connection process to complete. (It may
help to be about 4-6 feet away from light
when connecting.)

7. Once device has been successfully added you
can begin using it.

CONTROLLING THE DEVICE
To access the settings of the Smart Solar Light, press the
settings icon in the top right corner.
You can turn on an energy saving feature that will make the
light a little dimmer to conserve power at all times. That is
located under the settings icon.
The battery percentage of the light is also listed on the color
and white control panels of the light controls. It is shown
near the top and also shows a power gauge. When the
gauge is full, the battery is full and when the battery gets
low it starts to empty.
NOTE
(Light controls
can only be
accessed when
light is in the
dark or if
solar panel
is covered.)

There are four modes for the Solar Light.
Color, White, Scene and Music modes.
Color mode lets you change the color and brightness of the
light. Swipe up or down to change brightness percentage.
White Mode makes the light white. Swipe up or down to
change brightness percentage.
(To select color modes you can select the Light Bulb icon at
the bottom. You can switch between color and white modes
by swiping left or right on the dashes below the color picker)
COLOR AND WHITE MODES

SCENE AND MUSIC MODES
Scene mode has preprogrammed color settings to pick from.
You can also create a custom scene.
Music mode changes light to the rhythm of music the
phone speaker hears.
(To select these modes you can select the Paint and Music
icons at the bottom.

GROUPING MULTIPLE LIGHTS TOGETHER
If you have multiple solar lights you can group them into one
group so you can control all of the settings of all the lights at
the same time.
To group multiple lights together be sure to add all of the
lights to your Smartpoint Home App. Then select one of the
lights and press the settings button in the top right hand
corner. Then press “Create Group”. After that, select the lights
you want to add to the group and press “Save”. Next, name
the group and then press save. The group will now show up on
the home screen of your app. When you click on the group,
whatever settings you save in the group applies to all of the
lights in the group.

PUSH NOTIFICATIONS
If you have multiple solar lights you can group them into one
group so you can control all of the settings of all the lights at
the same time.
To group multiple lights together be sure to add all of the
lights to your Smartpoint Home App. Then select one of the
lights and press the settings button in the top right hand
corner. Then press “Create Group”. After that, select the lights
you want to add to the group and press “Save”. Next, name
the group and then press save. The group will now show up on
the home screen of your app. When you click on the group,
whatever settings you save in the group applies to all of the
lights in the group.
1. You can turn on/off notifications for all devices
connected to app by clicking on the “Me” button at the
bottom right of the screen.
2. Then click on ”Settings” button. From there you can turn
access notification settings.

REMOVE THE DEVICE
1. From the home screen, click on the Solar Light you would
like to remove.
2. Then click on the edit symbol on the top right of the
screen.
3. From there you would then click the “Remove Device”
button at the bottom of the screen.