SMC Networks EZ Connect SMC2670W User manual

SMC2670W

1
Copyright
Information furnished by SMC Networks.(SMC) is believed
to be accurate and reliable. However, no responsibility is
assumed by SMC for its use, nor for any infringements of
patents or other rights of third parties, which may result from
its use. No license is granted by implication or otherwise under
any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
Copyright © 2002 by
SMC Networks
All rights reserved. Printed in Taiwan
Trademarks
SMC is a registered trademark; and EZ Connect is a trademark
of SMC Networks, Inc. Other product and company names are
trademarks or registered trademarks of their respective holders.

2
Compliances
FCC Class B
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consultthe dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

3
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment.This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in con-
junction with any other antenna or transmitter.
Industry Canada - Class B
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus as set out in the
interference-causing equipment standard entitled “Digital
Apparatus,” ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de
Classe B prescrites dans la norme sur le matérial brouilleur:
“Appareils Numériques,” NMB-003 édictée par l’Industrie.

8
Congratulations on your purchase of the EZ Connect™ 2.4GHz
11 Mbps Wireless Ethernet Adapter.The EZ Connect™ Wireless
Ethernet Adapter is the perfect device for connecting any
Ethernet enabled device, such as a printer or game console, to
your wireless network. Plug and Play installation allows users
to set-up this adapter to connect to any existing 802.11b
wireless network in minutes. By offering both a windows-based
and web-based administration utility, the EZ Connect Wireless
Adapter can be managed from any PC on your network.To
secure this wireless connection, the EZ Connect Wireless
Ethernet Adapter supports 64/128-bit Wired Equivalent Privacy
(WEP) encryption. For setup instructions, see section 3.
Benefits:
•IEEE 802.11b compliant ensure seamless interoperability
among multiple vendors
•11 Mbps performance meets most foreseeable
networking needs
•Perfectforconnecting network-enabled game console systems.
•64/128-bit WEP ensures secure network connection
•Simple and easy installation by using the convenient web
or windows-based configuration utility.
Compatibility:
•IEEE 802.3
•IEEE 802.11b

9
The EZ Connect Wireless Ethernet Adapter package
includes the following:
•OneEZConnect™ 2.4GHz 11 Mbps Wireless
Ethernet Adapter
•One CD containing EZ Installation Wizard, Utility
Software and Complete Documentation
•OnePower Adapter
•One CAT 5 Crossover Cable
•OneManual
Minimum Requirements:
•An A/C power outlet (100 – 120V, 50 – 60Hz), to supply
power to the Wireless Ethernet Adapter.
•Anavailable RJ-45 port on a 10BASE-T Ethernet device.
•802.11 compliant wireless Ethernet adapters with TCP/IP
compatible protocol installed.

10
Section 1 | Getting Started
Site Location
Choose a location for your EZ Connect Wireless Ethernet
Adapter. Usually, the best location is at the center of your
wireless coverage area, and if possible within line-of-sight of
your main wireless broadcast device, such as an Access Point
or a Wireless Router.
Connect the Ethernet Cable
The EZ Connect Wireless Ethernet Adapter can be connected
to any device that has a standard Ethernet connection. Use a
standard Category 5 UTP Crossover Ethernet cable with an RJ-
45 connector to connect the Wireless Ethernet Adapter to any
Ethernet-enabled device.
Note: Do not connect this adapter directly to the LAN
port of a router, such as the Barricade.
Connect the Power Cable
Connect the power adapter cable to the 5V DC power socket
on the rear panel.
Warning: Use only the power adapter supplied with the
SMC2670W. Using another power adapter will cause
damage to the unit and void the warranty.
Antenna
Indicator Lights:
• Power
• Wireless Transmit/Receive
• Ethernet Link/Acivity

11
1.1 | Wireless Ethernet Adapter LED Indicators
The preceding diagram shows the location of all ports, jacks,
controls, and LED indicator lights on the EZ Connect 11 Mbps
Wireless Ethernet Adapter. The Wireless Ethernet Adapter
contains 1 external antenna, which is adjustable for best
wireless reception.
The front of the Wireless Ethernet Adapter has 3 labeled indi-
cator lights.When you connect your Wireless Ethernet Adapter,
these lights will be on, off, or blinking, indicating the following
states.
Light On Off Blinking
LNK/ACT Ethernet Connection No Ethernet Data being sent or
Connection received over
Ethernet
TX/RX Wireless Connection No Wireless Scanning for
Connection wireless signal
PWR Receiving Power Not Receiving N/A
Power

12
1.2 | Resetting the Wireless Ethernet Adapter
To reset the SMC2670W Wireless Ethernet Adapter or to correct
temporary connectivity problems, follow the steps outlined
below:
1. Locate the [Default] button on the back of the EZ Connect
Wireless Ethernet Adapter.
2. Unplug the power from the back of the Wireless Ethernet
Adapter for 5 seconds.
3. Hold down the [Default] button, located on the back of
the device.
4. Plug the power connector into the Wireless Ethernet
Adapter while holding down the [Default] button.
5. Release the [Default] button after 3 seconds.
6. Wait another 3 seconds, and then push and hold down the
[Default] button again.
7. The "LNK/ACT" and "TX/RX" LED indicators will blink once
per second about 10-12 times.
8. When the LED indicators begin flashing rapidly, release the
[Default] button.