SMC Networks 100BASE-TX Programming manual

TigerSwitch 10/100
16-Port Fast Ethernet Switch
◆ 16 10BASE-T/100BASE-TX ports
◆ Optional 1000BASE-X or 100BASE-FX modules
◆ 8.8 Gbps of aggregate bandwidth
◆ Non-blocking switching architecture
◆ Spanning Tree Protocol
◆ Up to four port trunks
◆ RADIUS and TACACS+ authentication
◆ Rate limiting for bandwidth management
◆ QoS support for four-level priority
◆ Full support for VLANs with GVRP
◆ IP Multicasting with IGMP Snooping
◆ Manageable via console, Web, SNMP/RMON
Management Guide
SMC6716AL2

38 Tesla
Irvine, CA 92618
Phone: [phone]
TigerSwitch 10/100
Installation Guide
From SMC’s Tiger line of feature-rich workgroup LAN solutions
July 2004
Pub. # 150000013500H

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of
patents or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
Copyright © 2004 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618.
All rights reserved. Printed in Taiwan
Trademarks:
SMC is a registered trademark; and TigerStack and TigerSwitch are trademarks of SMC
Networks, Inc. Other product and company names are trademarks or registered trademarks
of their respective holders.

i
L IMITED W ARRANTY
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be
free from defects in workmanship and materials, under normal use and service, for the
applicable warranty term. All SMC products carry a standard 90-day limited warranty from
the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion,
repair or replace any product not operating as warranted with a similar or functionally
equivalent product, during the applicable warranty term. SMC will endeavor to repair or
replace any product returned under warranty within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering
new products within 30 days of purchase from SMC or its Authorized Reseller. Registration
can be accomplished via the enclosed product registration card or online via the SMC Web
site. Failure to register will not affect the standard limited warranty. The Limited Lifetime
warranty covers a product during the Life of that Product, which is defined as the period of
time during which the product is an “Active” SMC product. A product is considered to be
“Active” while it is listed on the current SMC price list. As new technologies emerge, older
technologies become obsolete and SMC will, at its discretion, replace an older product in its
product line with one that incorporates these newer technologies. At that point, the obsolete
product is discontinued and is no longer an “Active” SMC product. A list of discontinued
products with their respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty.
All products that are replaced become the property of SMC. Replacement products may be
either new or reconditioned. Any replaced or repaired product carries either a 30-day limited
warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible
for any custom software or firmware, configuration information, or memory data of
Customer contained in, stored on, or integrated with any products returned to SMC pursuant
to any warranty. Products returned to SMC should have any customer-installed accessory or
add-on components, such as expansion modules, removed prior to returning the product for
replacement. SMC is not responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to returning
any product to SMC. Proof of purchase may be required. Any product returned to SMC
without a valid Return Material Authorization (RMA) number clearly marked on the outside
of the package will be returned to customer at customer’s expense. For warranty claims within
North America, please call our toll-free customer support number at [phone].
Customers are responsible for all shipping charges from their facility to SMC. SMC is
responsible for return shipping charges from SMC to customer.

ii
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN
LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE,
INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE
UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE
ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR
ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT
OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE
SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED
RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES
OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS
WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the active
SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans,
and cables are covered by a standard one-year warranty from date of purchase.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618

i
Contents
Chapter 1: Introduction 1-1
Key Features 1-1
Description of Software Features 1-2
System Defaults 1-5
Chapter 2: Initial Configuration 2-1
Connecting to the Switch 2-1
Configuration Options 2-1
Required Connections 2-2
Remote Connections 2-3
Basic Configuration 2-3
Console Connection 2-3
Setting Passwords 2-4
Setting an IP Address 2-4
Manual Configuration 2-4
Dynamic Configuration 2-5
Enabling SNMP Management Access 2-6
Community Strings 2-6
Trap Receivers 2-7
Saving Configuration Settings 2-7
Managing System Files 2-8
Chapter 3: Configuring the Switch 3-1
Using the Web Interface 3-1
Navigating the Web Browser Interface 3-2
Home Page 3-2
Configuration Options 3-3
Panel Display 3-3
Main Menu 3-4
Basic Configuration 3-8
Displaying System Information 3-8
Displaying Switch Hardware/Software Versions 3-9
Displaying Bridge Extension Capabilities 3-11
Setting the Switch’s IP Address 3-12
Manual Configuration 3-13
Using DHCP/BOOTP 3-14
Managing Firmware 3-15
Downloading System Software from a Server 3-16
Saving or Restoring Configuration Settings 3-17
Downloading Configuration Settings from a Server 3-18

Contents
ii
Console Port Settings 3-19
Telnet Settings 3-21
Configuring Event Logging 3-23
System Log Configuration 3-23
Remote Logs Configuration 3-25
Displaying Log Messages 3-26
Resetting the System 3-27
Setting the System Clock 3-27
Configuring SNTP 3-28
Setting the Time Zone 3-29
Simple Network Management Protocol 3-29
Setting Community Access Strings 3-30
Specifying Trap Managers and Trap Types 3-31
User Authentication 3-32
Configuring User Accounts 3-32
Configuring Local/Remote Logon Authentication 3-34
Configuring HTTPS 3-37
Replacing the Default Secure-site Certificate 3-38
Configuring the Secure Shell 3-39
Generating the Host Key Pair 3-41
Configuring the SSH Server 3-43
Configuring Port Security 3-44
Configuring 802.1x Port Authentication 3-46
Displaying 802.1x Global Settings 3-47
Configuring 802.1x Global Settings 3-48
Configuring Port Settings for 802.1x 3-48
Displaying 802.1x Statistics 3-51
Access Control Lists 3-53
Configuring Access Control Lists 3-53
Setting the ACL Name and Type 3-54
Configuring a Standard IP ACL 3-55
Configuring an Extended IP ACL 3-56
Configuring a MAC ACL 3-58
Binding a Port to an Access Control List 3-59
Filtering Addresses for Management Access 3-60
Port Configuration 3-62
Displaying Connection Status 3-62
Configuring Interface Connections 3-64
Creating Trunk Groups 3-66
Statically Configuring a Trunk 3-67
Enabling LACP on Selected Ports 3-68
Configuring LACP Parameters 3-70
Displaying LACP Port Counters 3-73
Displaying LACP Settings and Status for the Local Side 3-74
Displaying LACP Settings and Status for the Remote Side 3-76

Contents
iii
Setting Broadcast Storm Thresholds 3-77
Configuring Port Mirroring 3-79
Configuring Rate Limits 3-80
Rate Limit Granularity 3-80
Rate Limit Configuration 3-81
Showing Port Statistics 3-82
Address Table Settings 3-86
Setting Static Addresses 3-86
Displaying the Address Table 3-87
Changing the Aging Time 3-89
Spanning Tree Algorithm Configuration 3-89
Displaying Global Settings 3-90
Configuring Global Settings 3-93
Displaying Interface Settings 3-96
Configuring Interface Settings 3-99
VLAN Configuration 3-101
IEEE 802.1Q VLANs 3-101
Enabling or Disabling GVRP (Global Setting) 3-104
Displaying Basic VLAN Information 3-104
Displaying Current VLANs 3-105
Creating VLANs 3-107
Adding Static Members to VLANs (VLAN Index) 3-108
Adding Static Members to VLANs (Port Index) 3-110
Configuring VLAN Behavior for Interfaces 3-111
Private VLANs 3-113
Displaying Current Private VLANs 3-114
Configuring Private VLANs 3-115
Associating Community VLANs 3-116
Displaying Private VLAN Interface Information 3-117
Configuring Private VLAN Interfaces 3-118
Class of Service Configuration 3-120
Layer 2 Queue Settings 3-120
Setting the Default Priority for Interfaces 3-120
Mapping CoS Values to Egress Queues 3-122
Selecting the Queue Mode 3-123
Setting the Service Weight for Traffic Classes 3-124
Layer 3/4 Priority Settings 3-126
Mapping Layer 3/4 Priorities to CoS Values 3-126
Selecting IP Precedence/DSCP Priority 3-126
Mapping IP Precedence 3-127
Mapping DSCP Priority 3-128
Mapping IP Port Priority 3-130
Mapping CoS Values to ACLs 3-131
Multicast Filtering 3-132
Layer 2 IGMP (Snooping and Query) 3-133

Contents
iv
Configuring IGMP Snooping and Query Parameters 3-133
Displaying Interfaces Attached to a Multicast Router 3-135
Specifying Static Interfaces for a Multicast Router 3-136
Displaying Port Members of Multicast Services 3-137
Assigning Ports to Multicast Services 3-138
Chapter 4: Command Line Interface 4-1
Using the Command Line Interface 4-1
Accessing the CLI 4-1
Console Connection 4-1
Telnet Connection 4-1
Entering Commands 4-3
Keywords and Arguments 4-3
Minimum Abbreviation 4-3
Command Completion 4-3
Getting Help on Commands 4-3
Showing Commands 4-4
Partial Keyword Lookup 4-5
Negating the Effect of Commands 4-5
Using Command History 4-5
Understanding Command Modes 4-5
Exec Commands 4-6
Configuration Commands 4-6
Command Line Processing 4-8
Command Groups 4-9
Line Commands 4-10
line 4-10
login 4-11
password 4-12
timeout login response 4-13
exec-timeout 4-13
password-thresh 4-14
silent-time 4-15
databits 4-15
parity 4-16
speed 4-17
stopbits 4-17
disconnect 4-18
show line 4-18
General Commands 4-19
enable 4-19
disable 4-20
configure 4-21
show history 4-21