SMC Networks Barricade g SMC2804WBRP-G User manual

Barricade g Wireless Router with USB Print Server Manual
Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications
at any time without notice.
Copyright © 2003 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
All rights reserved.
Trademarks:
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc. Other product
and company names are trademarks or registered trademarks of their respective holders.
2

Barricade g Wireless Router with USB Print Server Manual
TABLE OF CONTENTS
CHAPTER 1 | Introduction
Features and Benefits
Package Contents
Minimum Requirements
CHAPTER 2 | Getting to know the Barricade g
LED Indicators
Resetting the Barricade g
CHAPTER 3 | Getting Connected
Basic Installation Procedure
3-click Installation Wizard
CHAPTER 4 | Configuring your Computer
Configuring Windows 95/98/Me
Configuring Windows 2000
Configuring Windows XP
Configuring a Macintosh Computer
CHAPTER 5 | Configuring the Barricade g
Browser Configuration
Disable Proxy Connection
Accessing the Barricade Management
CHAPTER 6 | Navigating the Web-based Administration
Making Configuration Changes
CHAPTER 7 | Setup Wizard
CHAPTER 8 | Advanced Setup
CHAPTER 9 | Setting up the Print Server
Install the SMC Printer Port Monitor
Configure the Print Server using the SMC Printer Port Monitor
Configure LPR port on Windows 2000/XP
APPENDIX A | PC Troubleshooting
APPENDIX B | Internet Connection Troubleshooting
APPENDIX C | Frequently Asked Questions
APPENDIX D | Port List – Application / Games
APPENDIX E | Technical Specifications
APPENDIX F | Compliances
APPENDIX G | Technical Support
3

Barricade g Wireless Router with USB Print Server Manual
CHAPTER 1 | Introduction
Congratulations on your purchase of a Barricade™ g Broadband Router with USB Print Server
(SMC2804WBRP-G). SMC is proud to provide you with a powerful yet simple communication device
for connecting your local area network (LAN) to the Internet and sharing a USB printer on your
network.
1.0 | Features and Benefits
•EZ 3-Click Installation Wizard - A new and improved way to install your Barricade in
seconds
•Built-in USB print Server to share your USB-enabled printer
•Internet connection to ethernet broadband modem via a 10/100 Mbps WAN port
•Local network connection via a 4-port auto-sensing 10/100 Mbps Ethernet switch
•DHCP for dynamic IP configuration, and DNS for domain name mapping
•Firewall with Stateful Packet Inspection, client privileges, hacker prevention, DoS, and NAT
•NAT also enables multi-user access with a single-user account, and virtual server
functionality (providing protected access to Internet services such as web, mail, FTP, and
Telnet)
•Virtual Private Network support using PPTP, L2TP, or IPSec pass-through
•User-definable application sensing tunnel supports applications requiring multiple
connections
•Parental controls allows the user to block access to certain web sites
•Email alerts when the users network is being compromised
•Easy setup through a web browser on any operating system that supports TCP/IP
•Compatible with various internet applications, including Peer-to-Peer file sharing, Online
Games, and Instant Message utilities.
1.1 | Package Contents
Before installing the Barricade™ g Broadband Router with USB Print Server, verify that you have the
items listed under “Package Contents.” Also be sure that you have the necessary cabling. If any of
the items are missing or damaged, contact your local SMC distributor.
•Barricade g Broadband Router with USB Print Server
•Power adapter (9v/1a)
•One CAT-5 Ethernet cable
•CD with User Guide and EZ 3-Click Installation Wizard
•Quick Installation Guide
If possible, retain the carton and original packing materials in case there is a need to return the
product.
1.2 | Minimum Requirements
•Cable or DSL Modem with Ethernet connection and Internet access from your local
telephone company or Internet Service Provider (ISP) using a DSL modem or cable modem.
•A computer equipped with a 10 Mbps, 100 Mbps, or 10/100 Mbps Fast Ethernet card, or
USB-to-Ethernet converter.
•Network adapter with Ethernet (UTP CAT 5) cabling and TCP/IP protocol installed per PC
•Internet Explorer 4.0 (or Higher) or Netscape Navigator 4.7 (or Higher) for Web-based
configuration of the Barricade
4

Barricade g Wireless Router with USB Print Server Manual
CHAPTER 2 | Getting to Know the Barricade
The SMC2804WBRP-G Barricade Cable/DSL Broadband Router is the perfect solution for the
home/office environment. This full-featured router offers:
•1 - USB 1.1 Print Server port
•802.11g Wireless with Performance Enhancing Nitro™ Technology
•4 - 10/100 Mbps Auto-Sensing LAN ports with Auto-MDI MDIX feature
•1 - 10/100 Mbps WAN port with Auto-MDI MDIX feature
•Comprehensive LEDs for network status and troubleshooting
•Reset Button
2.1 | LED Indicators
The Barricade includes LED indicators on the front panel that simplify installation and network
troubleshooting.
LED ON OFF FLASHING
PWR (POWER) Receiving power Not receiving power N/A
SPD (WAN) 100Mbps WAN
connection detected
10Mbps WAN
connection detected
N/A
Link/ACT (WAN) Good WAN connection
detected
No WAN connection
detected
Data transmitting
through the WAN
WLAN Wireless function is
enabled
Wireless function is
disabled
Data transmitting
through wireless
Link/ACT (LAN) Good LAN connection
detected
No LAN connection
detected
Data transmitting
through the LAN
Resetting the Barricade
The Reset button is located on the rear panel of the Barricade Broadband Router. Use a paper clip
or a pencil tip to push the Reset button.
Reset
If the Router is having problems connecting to the Internet, simply unplug the router for 3 seconds
then plug back in.
Restore Factory Defaults
If resetting the router does not resolve your issue, then you can follow these steps:
1. Leave power plugged into the router
2. Locate the reset button on the back panel, press and hold until WAN LED flashes off.
3. Release reset button.
5

Barricade g Wireless Router with USB Print Server Manual
CHAPTER 3 | Getting Connected
The SMC2804WBRP-G Barricade g Router with USB Print Server is connected between the Ethernet
Broadband Modem and your computers, either wired or wireless. If you have more then one
computer to connect, simply plug the other computers into the LAN ports on the back of the router
or connect via a wireless signal.
MODEM
connected
o WAN Portt
COMPUTER
connected to
LAN Port
3.1 | Basic Installation Procedure
1. CONNECT the WAN
Connect an Ethernet cable from your cable or DSL modem to the Barricade g WAN port on the
back on the router.
2. CONNECT the LAN
Run an Ethernet cable from one of the LAN ports on the back of the Barricade g to your
computer’s wired network adapter.
3. POWER on
Connect the power cable to the Barricade.
NOTE: It is highly recommended that you do you initial configuration from a wired connection.
Once you have completed connecting all of the hardware, simply insert the Barricade g CD-ROM
and the EZ 3-Click Installation Wizard will automatically get you connected you to the Internet.
For manual configuration of the PCs, see Chapter 4.
For advanced configuration of the Barricade Broadband Router, see Chapter 5.
6

Barricade g Wireless Router with USB Print Server Manual
CHAPTER 4 | Configuring your Computer
The information outlined in this chapter will guide you through the configuration for the following
Operating Systems:
•Windows 95/98
•Windows Me
•Windows 2000
•Windows XP
•Apple Macintosh
4.1 | Configuring Windows 95/98/Me
1. Access your Network settings by clicking [Start], choose [Settings], and then select [Control
Panel].
2. In the Control Panel, locate and double-click the [Network] icon.
3. Highlight the TCP/IP line that has been assigned to your network card on the
[Configuration] tab of the [Network] properties window.
4. Next, click the [Properties] button to view that adapter’s TCP/IP settings.
7

Barricade g Wireless Router with USB Print Server Manual
5. From the TCP/IP Properties dialog box, click the [Obtain an IP address automatically]
option.
6. Next click on the [Gateway] tab and verify the Gateway field is blank. If there are IP
addresses listed in the Gateway section, highlight each one and click [Remove] until the
section is empty.
7. Click the [OK] button to close the TCP/IP Properties window.
8. On the Network Properties Window, click the [OK] button to save these new changes.
NOTE: Windows may ask you for the original Windows installation disk or additional files.
Check for the files at c:\windows\options\cabs, or insert your Windows CD-ROM into your
CD-ROM drive and check the correct file location, for example, D:\win98, D:\win9x.
(assume “D” is your CD-ROM drive).
9. Windows may prompt you to restart the PC. If so, click the [Yes] button. If Windows does
not prompt you to restart your computer, do so anyways to ensure your settings.
4.2 | Configuring Windows 2000
1. Access your Network settings by clicking [Start], choose [Settings], and then select [Control
Panel]
2. In the Control Panel, locate and double-click the [Network and Dial-up Connections] icon
3. Locate and double-click the [Local Area Connection] icon for the Ethernet adapter that is
connected to the Barricade. When the Status dialog box window opens, click the
[Properties] button.
4. On the [Local Area Connection] Properties box, verify the box next to Internet Protocol
(TCP/IP) is checked. Then highlight the Internet Protocol (TCP/IP), and click the Properties
button.
5. Select Obtain an IP address automatically to configure your computer for DHCP. Click the
[OK] button to save this change and close the Properties window.
6. Click the [OK] button again to save these new changes.
7. Reboot your PC.
8

Barricade g Wireless Router with USB Print Server Manual
4.3 | Configuring Windows XP
The following instructions assume you are running Windows XP with the default interface. If you
are using the Classic interface (where the icons and menus look like previous Windows versions),
please follow the instructions for Windows 2000 outlined above.
1. Access your Network settings by clicking [Start], choose [Control Panel], select [Network
and Internet Connections] and then click on the [Network Connections] icon.
2. Locate and double-click the Local Area Connection icon for the Ethernet adapter that is
connected to the Barricade Router. Next, click the [Properties] button.
3. On the [Local Area Connection] Properties box, verify the box next to Internet Protocol
(TCP/IP) is checked. Then highlight the Internet Protocol (TCP/IP), and click the Properties
button.
4. Select Obtain an IP address automatically to configure your computer for DHCP. Click the
[OK] button to save this change and close the Properties window.
5. Click the [OK] button again to save these new changes.
6. Reboot your PC.
9

Barricade g Wireless Router with USB Print Server Manual
4.4 | Configuring a Macintosh Computer
You may find that the instructions here do not exactly match your screen. This is because these
steps and screenshots were created using Mac OS 8.5. Mac OS 7.x and above are all very similar,
but may not be identical to Mac OS 8.5.
1. Pull down the Apple Menu. Click [Control Panel] and select TCP/IP.
2. In the TCP/IP dialog box, make sure that [Ethernet] is selected in the [Connect Via:] field.
If [Using DHCP Server] is already selected in the [Configure] field, your computer is already
configured for DHCP. Close the TCP/IP dialog box, and skip to Step 2 Disable HTTP Proxy
(bottom of this page).
3. All the information that you need to record is on the [TCP/IP] dialog box. Use the space
below to record the information.
4. Select [Using DHCP Server] in the [Configure] field and close the window.
5. Another box will appear asking whether you want to save your TCP/IP settings. Click
[Save].
10