SMC Networks EZ Connect SMC7003ADSL User manual

ADSL Bridge/Router
SMC7003ADSL
Read Me First
User’s Manual

SMC7003ADSL (version 1.0)
The product names found in this manual are used for identification
purposes only and may be trademarks and/or registered trademarks of
their respective companies.
Copyright 2001
All Rights Reserved. No part of this document may be reproduced by
any means without the express permission of the company.
The information contained in this document is believed to be accurate
in every respect. We, however, cannot assume responsibility for any
consequences resulting from the use thereof. Information contained
within this document is subject to change. Revision to this document,
or new additions to it, may be issued to incorporate such changes.
Revision Status:
Model number Rev. Date Change
SMC7003ADSL 1.0 February 2001 Preliminary

Introduction
SMC7003ADSL (version 1.0) i
Introduction
The SMC7003ADSL provides unrivaled asymmetric high-speed data transport over a
single copper pair. Its very rich feature set includes an easy to use Setup Wizard, DHCP
support, a firewall for network protection and VPN capabilities for reduced cost of remote
access communications.
PACKING LIST
1. SMC7003ADSL Bridge/Router
2. DSL Cable (RJ-11, green cable)
3. Ethernet Cable (RJ-45, yellow cable)
4. USB Cable (grey cable)
5. Power Cord
6. AC Power Adapter
7. CD with the GUI software and USB Drivers
8. User’s Manual

Table of Contents
SMC7003ADSL (version 1.0) ii
Table of contents
Introduction
Chapter 1 Product Description 1
1.1 Minimum PC Requirements 1
1.2 Physical Descriptions 1
1.3 Front Status Indicators 2
1.4 Rear Panel 3
1.5 Parameters From Service Provider 4
1.6 Default Settings 6
Chapter 2 Installation 7
2.1 Hardware Installation Procedures 7
2.1.1 Ethernet Connection 8
2.1.2 USB Connection 9
2.2 Connecting the PC to the SMC7003ADSL 10
2.2.1 Ethernet Connection 10
2.2.2 USB Installation 15
2.2.2.1 How to install the USB Driver 15
2.2.2.2 Configuring the PC for the USB 16
Chapter 3 Configuration 17
3.1 GUI Installation 17
3.2 Easy Setup Flow Chart 18
3.3 Login Screen 19
3.4 Bridge Mode Configuration 20
3.5 Router Mode Configuration 22
Chapter 4 Warranty and Shipping Information 25
4.1 Customer Service and Technical Support 25
4.2 SMC’s Limited Warranty 26
Appendix A FCC Notice 29
Appendix B Installation of TCP/IP Protocol 31
Appendix C Interface Pin Assignments 33

Chapter 1 - Product Description
SMC7003ADSL (version 1.0) 1
CHAPTER 1 - PRODUCT
DESCRIPTION
aA PC with an installed 10BaseT Ethernet card or USB interface.
aTCP/IP network protocol installed on the PC.
aWindows 95 (USB port may have some compatibility issues), Windows 98,
Windows 2000, Windows NT 4.0 (no support for USB) or Windows Me.
aFor Ethernet connectivity to our system, you can use any Operating System
with the TCP/IP protocol such as Linux, Mac, OS2 etc.
The SMC7003ADSL is a compact, light-weight communications device with the
following dimensions:
4Height : 1.5"
4Width : 8"
4Depth : 6"
4Weight : 1.5 lbs
4Color : Off White
1.1 Minimum PC Requirements
1.2 Physical Descriptions

Chapter 1 - Product Description
2 SMC7003ADSL (version 1.0)
The Front panel includes four status indicators as shown in the table below:
LEDs COLOR EXPLANATION
POWER Green (solid) It will illuminate as soon as the device is
powered ON and will remain on till the
device is turned OFF.
SYNC Green (solid) It illuminates to indicate successful
connection to the Network.
ALARM Red (solid) It indicates the device encountering an error.
ATM ACT Green (solid/blinking) The ATM Activity LED shows data traffic.
During normal operation, it should be
blinking.
1.3 Front Status Indicators

Chapter 1 - Product Description
SMC7003ADSL (version 1.0) 3
EXPLANATION
DSL RJ-11 port for DSL connection (cable provided).
POWER SWITCH Permits the device to be turned ON/OFF.
POWER OUTLET A receptacle for the AC Power Adapter.
RESET SWITCH To return the device to factory settings.
ETHERNET Allows the SMC7003ADSL to establish a connection either to
a hub or directly to a PC and requires a RJ-45 cable
(provided). It has 2 LEDs. The Link LED (green) remains
solid when connected to an active Ethernet port. The Activity
LED (yellow) will blink when there is traffic.
USB Allows a direct connection to a PC for greater flexibility and
simultaneous sharing of local resources and the ADSL line
(cable provided).
1.4 Rear Panel

Chapter 1 - Product Description
4 SMC7003ADSL (version 1.0)
Depending on Service Providers, automatic configuration or the following parameters
may be provided by the Service Provider (ISP) for configuring the PC or Router.
Example shown below:
4IP Address 10 . 10 . 12 . 102
4Subnet Mask Address 255 . 255 . 255 . 0
4Gateway Address 10 . 10 . 12 . 1
4DNS Server Address 202 . 23 . 3 . 75
4Domain Address 10 . 10 . 12 . 40
4vci value (default: vci=35) 35
4vpi value (default: vpi=0) 0
1.5 Parameters From Service Provider

Chapter 1 - Product Description
SMC7003ADSL (version 1.0) 5
WORKSHEET
PLEASE HAVE THIS INFORMATION BEFORE YOU PROCEED:
4IP Address ___ . ___ . ___ . ___
4Subnet Mask Address ___ . ___ . ___ . ___
4Gateway Address ___ . ___ . ___ . ___
4DNS Server Address ___ . ___ . ___ . ___
4Domain Address ___ . ___ . ___ . ___
4vci value (default: vci=35) ___
4vpi value (default: vpi=0) ___
NOTE:
aIf vci/vpi values are the same as the default, you do not need to make any
changes in the Bridge Mode.
aExtra copy of this page is provided on the last page of this manual.

Chapter 1 - Product Description
6 SMC7003ADSL (version 1.0)
SYSTEM MODULE
4ip-address : 10.0.0.1
4subnet-mask : 255.255.255.0
4user name : admin
4password : password (minimum 4 alphabetic characters)
4language : english
ATM MODULE
4vc-no : 0
4vpi : 0
4vci : 35
4vc-type : ATM_PVC
4encap type : LLC_MUX
4encap protocol : RFC1483 (BRIDGED)
1.6 Default Settings