SMC Networks GS5 - annexe 1 User manual

EZ Connect N
Draft 11n Wireless USB2.0 Adapter
EZ Switch™
5/8 port Gigabit Ethernet Switch
SMCGS5/SMCGS8

1
Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of
patents or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
Copyright © 2009 by
SMC Networks, Inc.
20 Mason
Irvine, CA 92618
All rights reserved. Printed in Taiwan
Trademarks:
SMC is a registered trademark; and EZ Switch is a trademark of SMC Networks, Inc. Other
product and company names are trademarks or registered trademarks of their respective
holders.

2
Warranty and
Product Registration
To register SMC products and to review the detailed warranty statement, please refer to the
Support Section of the SMC Website at http://www.smc.com
SMC Networks, Inc.
20 Mason
Irvine, CA 92618

3
Compliances
Federal Communication Commission Interference Statement
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct
the interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to meet FCC
emission limits. SMC is not responsible for any radio or television interference caused by
using other than recommended cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications could void the
user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
EC Declaration of Conformity
SMC contact for these products in Europe is:
SMC Networks Spain, S.L.
Edificio Conata II,
Group CTSG
Fructuos Gelabert 6-8 2o2a
08970 Sant Joan Despi, Barcolona,Spain
This information technology equipment complies with the requirements of the Council
Directive 2004/108/EC on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 2006/95/EC for electrical equipment used within certain
voltage limits and the Amendment Directive 2006/95/EC. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission:
•Limit class A according to EN 55022: 2006(EMC)
•Limit class A for harmonic current emission according toEN 61000-3-
2/2000+A2:2005
•Limitation of voltage fluctuation and flicker in low-voltage supply system according
to EN 61000-3-3/1995+A1:2001+A2:2005
Immunity:
•Product family standard according to EN 55024:1998+A1:2001+A2:2003

4
•Electrostatic Discharge according to EN 61000-4-2: 2001 ED.1.2
(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
•Radio-frequency electromagnetic field according to EN 61000-4-3: 2006 ED.3.0
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)
•Electrical fast transient/burst according to EN 61000-4-4: 2004 ED.2.0 (AC/DC
power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
•Surge immunity test according to EN 61000-4-5: 2005 ED.2.0
(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
•Immunity to conducted disturbances, Induced by radio-frequency fields:
EN 61000-4-6: 2006 ED.2.2 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3
V/m)
•Power frequency magnetic field immunity test according to
EN 61000-4-8: 2001 ED.1.1 (1 A/m at frequency 50 Hz)
•Voltage dips, short interruptions and voltage variations immunity test according to
EN 61000-4-11: 2004 ED.2.0 (>95% Reduction @10 ms, 30% Reduction @500 ms,
>95% Reduction @5000 ms)
LVD:
•EN 60950-1:2006
Industry Canada Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled .Digital
Apparatus,. ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel
brouilleur: .Appareils Numériques,. NMB-003 édictée par le ministère des Communications.

5
Please read the following safety information carefully before
installing the Switch:
WARNING: Installation and removal of the unit must be carried out by qualified personnel
only.
•This guide is intended for use by network administrators who are responsible for
setting up and installing network equipment; consequently it assumes a basic
working knowledge of LANs (Local Area Networks).
•The unit must be connected to an earthed (grounded) outlet to comply with
international safety standards.
•Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)
connection.
•The appliance coupler (the connector to the unit and not the wall plug) must have a
configuration for mating with an EN 60320/IEC 320 appliance inlet.
•The socket outlet must be near to the unit and easily accessible. You can only
remove power from the unit by disconnecting the power cord from the outlet.
•This unit operates under SELV (Safety Extra Low Voltage) conditions according to
IEC 60950. The conditions are only maintained if the equipment to which it is
connected also operates under SELV conditions.

6
France and Peru only
This unit cannot be powered from IT. supplies. If your supplies are of IT type, this unit
must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary
connection point labelled Neutral, connected directly to earth (ground). †Impédance à la
terre
Power Cord Set
The cord set must be UL-approved and CSA certified.
The minimum specifications for the flexible cord are: - No.
18 AWG - not longer than 2 meters, or 16 AWG. - Type
SV or SJ - 3-conductor
The cord set must have a rated current capacity of at least
10A.
U.S.A. and Canada
The attachment plug must be an earth-grounding type with
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V)
configuration.
Denmark The supply plug must comply with Section 107-2-D1,
Standard DK2-1a or DK2-5a.
Switzerland The supply plug must comply with SEV/ASE 1011.
The supply plug must comply with BS1363 (3-pin 13 A) and
be fit-ted with a 5 A fuse which complies with BS1362.
U.K.
The mains cord must be <HAR> or <BASEC> marked
and be of type HO3VVF3GO.75 (minimum).
The supply plug must comply with CEE7/7 (.SCHUKO.).
The mains cord must be <HAR> or <BASEC> marked
and be of type HO3VVF3GO.75 (minimum).
Europe
IEC-320 receptacle.

7
Veuillez lire à fond l’information de la sécurité suivante avant
d’installer le Switch:
AVERTISSEMENT: L.installation et la dépose de ce groupe doivent être confiés à un
personnel qualifié.
•Ne branchez pas votre appareil sur une prise secteur (alimentation électrique)
lorsqu’il n’y a pas de connexion de mise à la terre (mise à la masse).
•Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de
respecter les normes internationales de écurité.
•Le coupleur d.appareil (le connecteur du groupe et non pas la prise murale) doit
respecter une configuration qui permet un branchement sur une entrée d.appareil
EN 60320/IEC 320.
•La prise secteur doit se trouver à proximité de l.appareil et son accès doit être facile.
Vous ne pouvez mettre l.appareil hors circuit qu.en débranchant son cordon
électrique au niveau de cette prise.
•L.appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme
à la norme IEC 60950. Ces conditions ne sont maintenues que si l.équipement
auquel il est raccordé fonctionne dans les mêmes conditions.
France et Pérou uniquement:
Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos
alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension
de 230 V (2 P+T) par le biais d.un transformateur d.isolement à rapport 1:1, avec un point
secondaire
de connexion portant l.appellation Neutre et avec raccordement direct à la terre (masse).
Cordon électrique - Il doit être agréé dans le pays d.utilisation
Le cordon doit avoir reçu l′homologation des UL et un
certificat de CSA.
Les spe’cifications minimales pour la corde flexible sont
AWG No. 18, ou AWG No. 16 pour une longueur
infe’rieure a‘ 2 me’tres:
- type SV ou SJ
- 3 conducteurs
Le cordon doit être en mesure d.acheminer un courant
nominal d.au moins 10 A.
Etats-Unis et Can-ada:
La prise femelle de branchement doit être du type à mise à
la terre (mise à la masse) et respecter la configuration
NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250
V).
Danemark: La prise mâle d.alimentation doit respecterla la section 107-
2 D1 de norme DK2 1a ou DK2 5a.
Cordon électrique - Il doit être agréé dans le pays d.utilisation
Suisse: La prise mâle d.alimentation doit respecter la norme
SEV/ASE 1011.

8
Europe
La prise secteur doit être conforme aux normes CEE
7/7 (.SCHU- KO. LE cordon secteur doit porter la
mention <HAR> ou <BASEC> et doit être de type
HO3VVF3GO.75 (minimum).
Bitte unbedingt vor dem Einbauen des RPU die folgenden Sicherheitsanweisungen
durchlesen:
WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal
erfolgen.
•Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren
vorgesehen, die fr die Installation und das einstellen von
Netzwerkkomponenten verantwortlich sind; sie setzt Erfahrung bei der Arbeit mit
LANs (Local Area Networks) voraus.
•Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose
angeschlossen werden.
•Das Gerät muß an eine geerdete Steckdose angeschlossen werden,
welche die internationalen Sicherheitsnormen erfüllt.
•Der Gerätestecker (der Anschluß an das Gerät, nicht der
Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320
konfigurierten Geräteeingang haben.
•Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die
Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der
Netzsteckdose unterbrochen werden.
•Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben,
wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen
betrieben werden
Stromkabel.
Dies muss von dem Land, in dem es benutzt wird geprüft werden:
Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen
ein- halten.
Europe
Das Netzkabel muß vom Typ HO3VVF3GO.75
(Mindestan-forderung) sein und die Aufschrift <HAR> oder
BASEC> tragen Der Netzstecker muß die Norm CEE 7/7
erfüllen (.SCHUKO.).
Warnings and Cautionary Messages
Warning: This product does not contain any serviceable user parts.
Warning: Installation and removal of the unit must be carried out by qualified personnel
only.

9
Warning: When connecting this device to a power outlet, connect the field ground lead on
the tri-pole power plug to a valid earth ground line to prevent electrical hazards.
Caution: Wear an anti-static wrist strap or take other suitable measures to prevent
electrostatic discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this
device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!
Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC
standards.
Warnings (in German)
Achtung: Dieses Produkt enthält keine Teile, die eine Wartung vom Benutzer benötigen.
Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem
Servicepersonal durchgeführt werden.
Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß n
Netzstecker mit Schutzerde verbunden werden, um elektrische Gefahren zu vermeiden.
Warnings (in Korean)
A급기기 (업무용 정보통신기기)
이기기는 업무용으로 전자파 등록을 한기기 이오니 판매자 또는 사용자는 이점을 주의 하시기
바라며, 만약 잘못 판매 또는 구입하였을 때에는 가정용으로 교환하시기 바랍니다.