SMC Networks AFJ20-D Series User manual

Doc. No. DOC1061738
PRODUCT NAME
VACUUM FILTER
MODEL / Series / Product Number
AFJ20-(F,N)01～(F,N)02(B)-(5,40,80)-(S,T)(-6,R,Z)-D
AFJ30-(F,N)02～(F,N)03(B)-(5,40,80)-(S,T)(-6,R,Z)-D
AFJ40-(F,N)02～(F,N)04(B)-(5,40,80)-(S,T)(-6,R,Z)-D

-1-
Contents
Page
1. Safety Instructions
2-6
2. Application
7
3. Standard Specifications
7
4. How to Order
8
5. Structural Drawing, Option and Replacement Parts
9
6. Bowl Assembly Specifications
10
7. Assembly of Optional Parts
11
8. Trouble Shooting
12
9. How to Replace the Components
13-16
9-1. Bowl Assembly Replacement
13-14
9-2. Element Replacement
15-16
10. Disassembly Drawing
17
11. Dimensions
18

-2-
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage. These
instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all
important notes for safety and must be followed in addition to International Standards (ISO/IEC)*1), and other safety
regulations.
1) ISO 4414: Pneumatic fluid power - General rules and safety requirements for systems and their components
ISO 4413: Hydraulic fluid power - General rules and safety requirements for systems and their components
IEC 60204-1: Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 10218-1: Robots and robotic devices - Safety requirements for industrial robots - Part 1:Robots
etc.
Danger
Danger indicates a hazard with a high level of risk which, if not avoided, will result
in death or serious injury.
Warning
Warning indicates a hazard with a medium level of risk which, if not avoided, could
result in death or serious injury.
Caution
Caution indicates a hazard with a low level of risk which, if not avoided, could result
in minor or moderate injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the equipment or
decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and test results. The expected performance and safety assurance of the equipment will be
the responsibility of the person who has determined its compatibility with the product. This person should also
continuously review all specifications of the product referring to its latest catalog information, with a view to
giving due consideration to any possibility of equipment failure when configuring the equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and
maintenance of machines or equipment including our products must be performed by an operator who is
appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
1. The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product precautions
of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Our products cannot be used beyond their specifications. Our products are not developed,
designed, and manufactured to be used under the following conditions or environments. Use
under such conditions or environments is not covered.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to
direct sunlight.
2. Use for nuclear power, railways, aviation, space equipment, ships, vehicles, military application, equipment
affecting human life, body, and property, fuel equipment, entertainment equipment, emergency shut-off
circuits, press clutches, brake circuits, safety equipment, etc., and use for applications that do not conform
to standard specifications such as catalogs and operation manuals.
3. Use for interlock circuits, except for use with double interlock such as installing a mechanical protection
function in case of failure. Please periodically inspect the product to confirm that the product is operating
properly.

-3-
Safety Instructions
Caution
We develop, design, and manufacture our products to be used for automatic control equipment, and
provide them for peaceful use in manufacturing business.
Use in non-manufacturing business is not covered.
Products we manufacture and sell cannot be used for the purpose of transactions or certification specified in the
Measurement Act.
The new Measurement Act prohibits use of any unit other than SI units in Japan.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance Requirements”.
Read and accept them before using the product.
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is
first.∗2)
Also, the product may have specified durability, running distance or replacement parts. Please consult your
nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement
product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage incurred due to
the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the
specified catalog for the particular products.
*2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to
the deterioration of rubber material are not covered by the limited warranty
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of mass destruction
(WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by the relevant security
laws and regulations of the countries involved in the transaction. Prior to the shipment of a SMC product to
another country, assure that all local rules governing that export are known and followed.

Precautions for Design
Warning
(1) Do not use the product if no leakage is allowed due to the environment, or if the fluid is not air.
(2) Polycarbonate resin is used for the external parts including the bowl. Organic solvents including
thinner, acetone, alcohol and ethylene chloride; chemicals including sulphuric acid, nitric acid and
hydrochloric acid; cutting oil, synthetic oils, ester-based compressor oil, alkali, kerosene, gasoline,
lock material of screw are harmful. Do not use the product where these are present.
Chemical resistance of polycarbonate and nylon bowl
(3) Shield from ultra violet light and radiation with protective cover.
-4-
Polycarbonate Nylon
Hydrochloric acid
Sulfuric acid
Phosphoric acid
Chromic acid
Sodium hydroxide (Caustic soda)
Potash
Calcium hydroxide (Slack lime) ×
○
Ammonia water
Carbotane of soda
Sodium sulfide
Potassium nitrate ×
△
Sulfate of soda
Carbon tetrachloride
Chloroform
Ethylene chloride
Methylene chloride
Benzene
Toluene
Paint thinner
Acetone
Methyl ethyl ketone × ×
Cyclohexane
Ethyl alcohol
IPA
△×
Methyl alcohol
Gasoline
Kerosene
Phthalic acid dimethyl
Phthalic acid diethyl ×
○
Acetic acid
Methyl ether
Ethyl ether
× ×
Thread-lock fluid
Sea water ×
△
Leak tester
Type
Chemical name
Application examples
Material
Acid
Acid washing liquid for metals
△
×
Alkaline
Degreasing of metals
Industrial salts
Water-soluble cutting oil
Inorganic salts
-
Chlorine solvents
Cleaning liquid for metals
Printing ink
Dilution
×
△
Aromatic series
Coatings
Dry cleaning
×
△
Ketone
Photographic film
Dry cleaning
Textile industries
Alcohol
Antifreeze
Adhesives
Oil
-
×
○
Ester
Synthetic oil
Anti-rust additives
Ether
Brake oil additives
×
○
○: Essentially safe. △: Some effects may occur. ×: Effects will occur.
Amino
Methyl amino
Cutting oil
Brake oil additives
Rubber accelerator
Others
-

Caution
(1) Do not use the product under pressure except momentary pressure (0.5 MPa or less) such as
pressure release.
Selection
Warning
(1) Grease used on the internal sliding parts and seals may flow to the outlet side.
(2) Oil included in air cannot be separated.
(3) If a more powerful moisture separator of moist is necessary, the vacuum drain separator AMJ
series is recommended.
Installation
Warning
(1) Do not drop or apply impact during transportation or installation. It will cause damage to the
product and result in operation failure.
(2) Do not install in areas of high humidity or high temperature. Operation outside of the product
specification range may cause damage to the product or operation failure, or shorten the product
life.
(3) Connect the product ensuring the direction of "1"(IN) and "2"(OUT) for air direction and indicated
arrow. Incorrect connections may cause malfunction.
(4) Install with adequate space for maintenance beneath the product. Refer to the section [11.
Dimensions] (P18) for necessary space.
Piping
Warning
(1) Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to
remove chips, cutting oil and solid foreign material from inside the pipe. Contamination of piping
may cause damage or malfunction.
(2) When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and
sealant do not get inside the pipe. When a sealant tape is used, leave 1 thread ridges exposed at
the end of the threads.
(3) Connect piping/fittings using the recommended torque while holding the female thread side tightly.
Insufficient tightening torque leads to cause of loosening or sealing failure, and excessive
tightening torque leads to cause of breakage of screws. Tightening without holding female thread
applies an excessive force to the bracket directly, leading to breakage.
Recommended tightening torque
Unit: N m
Thread size
1/8
1/4
3/8
1/2
Torque
3 to 5
8 to 12
15 to 20
20 to 25
(4) Before using an SMC fitting and S coupler, please refer to "Tightening the threaded portion of the
connection thread" of the Fittings & Tubing Precautions.
(5) Do not apply torsion or bending moment other than the weight of the product itself. External piping
needs to be supported separately as it may cause breakage. Non-flexible piping like steel tube is
susceptible to excessive moment load or vibration. Insert flexible tubes to prevent this.
-5-

Air Source
Warning
(1) Use clean air. Do not use air containing chemicals, organic solvent, synthetic oil or corrosive gas
as it may be cause of breakage of components or operation failure.
Maintenance
Warning
(1) Release the pressure in the product to the atmosphere when replacing parts or removing piping.
(2) Maintenance and checks should be done by following the procedure in this operation manual.
Incorrect handling of the product may cause breakage or operation failure of the equipment or
device.
(3) Perform periodical check to find cracks, flaws or other deterioration on resin bowl.
If any of these appear, replace with a new bowl. Otherwise, breakage may occur. Investigate
and/or review the operating conditions if necessary.
(4) Check for dirt in resin bowl periodically. If any dirt is seen, replace with new bowl. If removing dirt by
washing the resin bowl, never use washing material other than neutral detergent. Otherwise, the
bowl is damaged.
(5) Replace the element every 2 years or when the pressure drop at the output pressure from initial
operation becomes 20 kPa, whichever comes first, to prevent damage to the element.
(6) For AFJ20-D, discharge drain in the bowl before it reaches the baffle. For AFJ30-D and AFJ40-D,
discharge drain in the bowl before it reaches the upper drain level indicated on the bowl. If drain
flows into the outlet side, it may be cause of operation failure. Furthermore, when drain is
discharged, release the pressure in the bowl to the atmosphere and remove the bowl before
proceeding. Refer to the section [9-1. Bowl Assembly Replacement] (P13-14) for removing the
bowl.
Caution
(1) When a filter element is used repeatedly, clean it with air blow or wash it with a neutral detergent.
(For 40 μm, For 80 μm)
Check the condition of the element and replace the element with a new one when the
specifications are not satisfied.
(2) Check the element periodically and replace it with a new one if necessary. If it is found that outlet
pressure drops lower than the normal condition or the flow is restricted during operation, check the
condition of the element.
(3) Do not apply excessive force to the mesh. (For 40 μm, For 80 μm)
It will cause the mesh to peel off.
-6-

2. Application
This product aims at eliminating drop of water and solid foreign matter in the air line for vaccum.
3. Standard Specifications
1/8 1/4 1/4 3/8 1/4 3/8 1/2
5 μm
80 100 180 230 200 310 370
40 μm
80 μm
5 μm
100 140 190 250 210 350 440
40 μm
80 μm
Note 1) 5 μm elements use fiber type element which filtrate 5 μm.
Note 2) The element for 40 μm uses a resin mesh with openings of 40 μm in height and width.
Note 3) The element for 80 μm uses a resin mesh with openings of 80 μm in height and width.
Note 4) The size of solid particles collectable by the element 40 μm (80 μm) shall be 40 μm (80 μm) or more
in depth x height x width.
Note 5) The amount of processed air when the initial pressure loss is 4 kPa.
Model
AFJ20-D
AFJ30-D
AFJ40-D
Port size
45 cm3
Fluid
Air
Ambient and fluid temperature
-5 to 60 ℃(with no freezing)
Proof pressure
0.5 MPa
Standard (Polycarbonate)
Recommended
flow rate Note 5)
[L/min(ANR)]
Water drop
removal type
(-S)
Operating pressure range
-100 to 0 kPa
Filtration Note 1) to Note 4)
5 μm, 40 μm, 80 μm
Drain capacity
0.35 kg
Large flow
type
(-T)
120
-7-
380
230
180
Weight
340
210
Vacuum release pressure
0.5 MPa or less
Bowl material
Polycarbonate
Bowl guard
-
8 cm3
25 cm3
130
250
0.09 kg
0.17 kg
100
660
480
500
390
230

4. How to Order
AFJ - - - - - D
Note 1) Select one each for a to c.
Note 2) 〇: For the pipe thread type: NPT only
-8-
❶
❷
❸
❺
30
❹
03
B
T
❻
80
❼
20 30 40
Nil
● ● ●
N
● ● ●
F
● ● ●
01
● ー ー
02
● ● ●
03
ー ● ●
04
ー ー ●
Nil
● ● ●
B
● ● ●
5
● ● ●
40
● ● ●
80
● ● ●
S
● ● ●
T
● ● ●
Nil
● ● ●
6
● ● ●
Nil
● ● ●
R
● ● ●
Nil
● ● ●
Z
○Note 2) ○Note 2) ○Note 2)
Without bracket
Type
Filtration
Bracket
Large flow type
Water drop removal type
80 μm
40 μm
5 μm
With bracket
Pressure unit: psi Temp. unit: ℉
Pressure unit: kPa Temp. unit: ℃
Flow direction: Right to left
Flow direction: Left to right
Nyron bowl
Polycarbonate bowl
Symbol
Description
❹
Rc
NPT
G
❷
Thread type
❸
Port size
❼
a
❻
❺
Bowl
c
❶
Body size
b
Flow direction
Semi-
standard
Pressure unit
Temp. unit
1/2
1/8
1/4
3/8
Note 1)

5. Structural Drawing, Option and Replacement Parts
-9-
Structural drawing / Option / Replacement parts
AFJ20-D
AFJ30-D／AFJ40-D
Option
AFJ20-D AFJ30-D AFJ40-D
(1) AF24P-070AS AF34P-070AS AF44P-070AS
Note 1) Assembly of 2 types of bracket and 2 set screws.
Replacement Parts
AFJ20-D AFJ30-D AFJ40-D
5μm AF20P-060S AF30P-060S AF40P-060S
40μm AF22P-820S AF32P-820S AF42P-820S
80μm AF22P-830S AF32P-830S AF42P-830S
(3) AF24P-040S AF34P-040S AF44P-040S
(4) C2SFP-260S C32FP-260S C42FP-260S
(5)
(6) AW22P-070S AW32P-070S AW42P-070S
Note 1) The numbers in the table and structural drawing are consistent with the numbers in
[9. How to Replace the Components] (P13-16) and [10. Disassembly Drawing] (P17).
Note 2) The seal is for 40 μm and 80 μm elements.
Seal Note 2)
Bowl assembly
Bowl seal
Baffle
Bracket assembly Note 1)
Part name
Element
(2)
Refer to the section [6. Bowl Assembly Specifications] (P10).
Part name
No.
Part No.
No.
Part No.
(1)
(4)
(2)
(6)
(3)
(5)

6. Bowl Assembly Specifications
6-1. Bowl assembly for AFJ20-D
Semi-standard symbol
－6
6-2. Bowl assembly for AFJ30-D
Semi-standard symbol
－6
6-3. Bowl assembly for AFJ40-D
Semi-standard symbol
－6
Note 1) Part No. (5) includes Bowl seal (4). Refer to the section [10. Disassembly Drawing] (P17).
Note 2) "Z" in Part No. (5) indicates semi-standard specifications. The pressure unit: psi. The temperature unit: ℉
Note 3) Refer to the section [4. How to Order] (P8) for semi-standard symbols.
-10-
Appearance and
part No.
Appearance and
part No.
Appearance and
part No.
Semi-standard: -(Standard)
Piping port
thread type
Rc
G
NPT C2SJ(-Z)-D
Semi-standard: 6
Piping port
thread type
Rc
G
NPT C2SJ-6(Z)-D
C2SJ-6-D
C2SJ-D
(5) Part No.
(5) Part No.
Semi-standard: -(Standard)
Piping port
thread type
Rc
G
NPT C3SJ(-Z)-D
Semi-standard: 6
Piping port
thread type
Rc
G
NPT C3SJ-6(Z)-D
(5) Part No.
C3SJ-6-D
C3SJ-D
(5) Part No.
Semi-standard: -(Standard)
Piping port
thread type
Rc
G
NPT C4SJ(-Z)-D
Semi-standard: 6
Piping port
thread type
Rc
G
NPT C4SJ-6(Z)-D
C4SJ-6-D
C4SJ-D
(5) Part No.
(5) Part No.

7. Assembly of Optional Parts
Bracket
1) Mounting of bracket A
2) Mounting of bracket B
-11-
Fix the bracket B with the set screw (2 pcs.) included
in the package. Refer to the table below for the
tightening torque.
Insert bracket A from the front of the air filter so that
the fingers of the bracket A hold the air filter at the
groove and the bottom of the body.
Bottom of
the body
Groove
Vacuum filter
Bracket B
Bracket A Fingers
Set screw
(2 pcs.)
Model Tool Tightening torque
AFJ20-D
AFJ30-D
AFJ40-D
Phillips
screwdriver
0.75±0.2 N・m

8. Trouble Shooting
Refer to the sections [9. How to Replace the Components] (P13-16) and [10.Disassembly Drawing] (P17).
Category Failure
Flow rate
As pressure drop
is large, fluid
does not flow.
Replace the element.
P13-16
Air sucks from
the gap between
the bowl and
body.
Replace the bowl seal.Grease up before
replacing the bowl seal. Note)
P13-14
Air sucks from
the broken part
of the bowl.
Replace the bowl assembly.
P13-14
Operability
Too much drain
comes from the
piping of outlet
side.
Discharge drain after removing bowl and
replace the element.
P13-16
-12-
Note) Fluorine grease is recommended.
Trouble
Possible cause
Countermeasure
Page for
reference
Vacuum pressure
does not decrease
Drain level reaches the baffle.
The bowl is damaged.
The bowl seal is damaged.
Clog of the element.

9. How to Replace the Components
！ Warning
Before replacement, make sure that no pressure remains in the product.
After replacement, confirm that the product satisfies specific functions and no external leakage occurs before operating it.
9-1. Bowl Assembly Replacement
Applicable
model
Work
category
Tool Criteria
Disassembly 1)
Remove the bowl assembly from the product.
If the bowl assembly is tightened too much to
be removed, use the spanner specified for SMC
until it can be loosened by hand.
Spanner specified for SMC
Product No.: 1129129
－
Work
category
Tool Criteria
Assembly 1)
Screw the bowl assembly into the product.
Tighten it referring to the specified torque.
－
Reference
tightening
torque: 2.1 N m
-13-
Procedure
AFJ20-D
Procedure
Product
Element assembly
Replacement of the bowl
seal will be easier when the
element assembly is
removed first.
Refer to the section [ 9-2.
Element Replacement ]
(P15).
Product
(5) Bowl assembly
(4) Bowl seal
(5) Bowl assembly

Applicable
model
Work
category
Tool Criteria
Disassembly 1)
Remove the bowl assembly from the product.
While the lock button is held down, rotate the bowl
assembly by approx. 30 degrees so that the mating
marks of the body and bowl assembly meet each
other. Then remove the bowl assembly by pulling it
downward.
－ －
Work
category
Tool Criteria
Assembly 1)
Mount the bowl assembly to the product and rotate
the bowl assembly until the lock button is locked in
position as shown in the figure below.
－ －
-14-
Procedure
AFJ30-D
AFJ40-D
Procedure
Product
Lock button
Product
Align the mating marks
Rotate 30
degrees
【Step 2】
Pull downward
【Step 3】
Mating mark of the
bowl assembly
Mating mark of the body
(5) Bowl assembly
(4) Bowl seal
Element assembly
Replacement of the bowl
seal will be easier when the
element assembly is
removed first.
Refer to the section [ 9-2.
Element Replacement ]
(P16).
Lock button
Caution
Make sure that the lock button
is locked to the flute of the
product before pressurizing it.
Rotate 30
degrees
【Step 2】
Insert upward
【Step 1】
(5) Bowl assembly
【Step 1】
Pull down
the lock button

9-2. Element Replacement
Applicable
model
Work
category
Tool Criteria
Disassembly 1)
Remove the bowl assembly referring to the section [9-1. Bowl Assembly
Replacement] (P13), then remove the snap fits (2 pcs.) of the deflector and pull
upward to remove the element assembly.
－
－
2)
Rotate the baffle 90 degrees in the arrow direction to remove the element and
the seal (For 40 μm and 80 μm elements) from the element assembly.
－ －
Work
category
Tool Criteria
Assembly 1)
Mount the element to the deflector and the seal (For 40 μm and 80 μm
elements) to the baffle and rotate the baffle 90 degrees in the arrow direction to
mount the element.
－
－
2)
Press the deflector downward until the snap fits (2 pcs.) are engaged with the
bowl assembly. Mount the bowl assembly referring to section [9-1. Bowl
Assembly Replacement] (P13).
－
－
-15-
Procedure
AFJ20-D
Procedure
For 40 μm and
80 μm elements
For 40 μm and
80 μm elements
(2) Element
Rotate 90 degrees
【Step 1】
【Step 2】
Pull upward
Deflector
Snap fits
(2pcs.)
Deflector
(6) Seal
(3) Baffle
(2) Element
Deflector
(6) Seal
(3) Baffle
Deflector
Snap fits
(2pcs.)
【Step 1】
Rotate 90 degrees Insert the element assembly
【Step 2】

Applicable
model
Work
category
Tool Criteria
Disassembly 1)
Remove the bowl assembly referring to the section [9-1. Bowl Assembly
Replacement] (P14). With the bowl assembly removed, rotate the deflector 90
degrees while holding the holding part.
－ －
2)
Pull upward and remove the element assembly while holding the holding part. －－
3)
Rotate the baffle 90 degrees in the arrow direction to remove the element and
the seal (For 40 μm and 80 μm elements) from the element assembly.
－ －
Work
category
Tool Criteria
Assembly 1)
Mount the element to the deflector and the seal (For 40 μm and 80 μm
elements) to the baffle and rotate the baffle 90 degrees in the arrow direction to
mount the element.
－ －
2)
Insert the element assembly into the bowl assembly. － －
3)
Rotate 90 degrees in either direction so that the protruded part of the element
assembly engages with the recessed part of the bowl assembly. Mount the bowl
assembly referring to the section [9-1. Bowl Assembly Replacement] (P14).
－ －
-16-
Procedure
AFJ30-D
AFJ40-D
Procedure
For 40 μm and
80 μm elements
Holding part of the deflector
Engraved arrows
Protruded part
Recessed part
Rotate 90
degrees
Pull upward
【Step 1】
【Step 2】
Deflector
Deflector
(2) Element
(6) Seal
(3) Baffle
【Step 3】
Rotate 90 degrees
【Step 1】
Rotate 90 degrees Insert the element assembly Rotate 90 degrees
【Step 2】
【Step 3】
(3) Baffle
For 40 μm and
80 μm elements
(6) Seal
(2) Element
Deflector

10. Disassembly Drawing
-17-
I N
I N
OUT
AFJ30-D, AFJ40-D
AFJ20-D
Body
I N
I N
OUT
O-ring
Body
For 40 μm and
80 μm elements
(2) Element
Deflector
(6) Seal
(3) Baffle
O-ring
Deflector
(2) Element
For 40 μm and
80 μm elements
(6) Seal
(3) Baffle
(4) Bowl seal
(4) Bowl seal
(5) Bowl assembly
(5) Bowl assembly

11. Dimensions
AFJ20-D
AFJ30-D, AFJ40-D
-18-
OUT
IN
OUT
IN
P A B C D E G J M N Q R S T U V
AFJ20-D
1/8・1/4 40 79.3 18 21 ー25 21 30 27 22 5.4 8.4 60 2.3 28
AFJ30-D
1/4・3/8 53 104.3 22 27 30 35 27 41 35 25 6.5 13 71 2.3 32
AFJ40-D
1/4・3/8・1/2 70 136.1 26 36 38 40 36 50 52 30 8.5 13 88 2.3 39
Standard specifications
Bracket mount
Optional specifications
Model
(Option)
(Option)
Bracket
Bracket
(Port size)
(Port size)
Clearance for
maintenance
Clearance for
maintenance

Revision history
4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN
Tel: + 81 3 5207 8249 Fax: [phone]
URL https://www.smcworld.com
Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
© SMC Corporation All Rights Reserved