Softing CAN-PRO1-PCIE Instructions for use

V1.00.01
Softing Industrial Automation GmbH
Richard-Reitzner-Allee 6
D-85540 Haar
Tel.: (++49) 89/4 56 56-0
Fax.: (++49) 89/4 56 56-399
http://www.softing.com
CANpro PCI Express
(single channel)
Hardware User Manual
Part number: CAN-PRO1-PCIE
©Copyright Softing Industrial Automation GmbH, Munich Germany
Information in this document is subject to change without notice.

Page: 2
1 Installation
To properly install the CAN-PRO1-PCIE in your PC, please follow the instructions detailed in
the next sections.
1.1 System requirements
To run the CAN-PRO1-PCIE on a PC, the PC must meet the following requirements:
•PCI Express slot
•Windows7, Windows Vista or Windows XP installed
1.2 Software installation
The CAN-PRO1-PCIE software is part of the “CAN Drivers and API” CD which is also
available from the download section at www.softing.com.
•Insert the CD in your PC’s CD/DVD drive.
•Run the CANDriversAndSoftware32.exe for 32 bit operating systems or
CANDriversAndSoftware64.exe for 64 bit operating systems.
•Please follow the instructions given by the setup software.
NOTE:
Make sure to install the software b e f o r e you install
your CAN-PRO1-PCIE hardware for the first time.
1.3 Hardware and driver installation
Once the software setup is finished please shut down the PC and follow the steps listed
below to install the CAN-PRO1-PCIE hardware.
NOTE:
To prevent damage to the CAN-PRO1-PCIE or to the PC,
discharge yourself on a grounded object such as the
metal housing of the PC before touching the board.
•Make sure that the PC and all peripheral devices are powered down.
•Remove the housing cover (refer to the PC manual).
•Select an available PCI Express slot and remove the slot cover (bracket)
•Plug the board into the slot on the motherboard of the PC.
•Fasten the bracket of the CAN-PRO1-PCIE using the screw.
•Reassemble the housing cover.
•Turn ON the PC and applicable peripherals. >The computer will recognize the new hardware.
•When “New Hardware Wizard” asks if Windows Update should be connected
select No.
•In the next step select automatic software installation. This will install all required drivers.

Page: 3
Status LED Status
off no power or in reset state
flashing green in initialization state
solid green CAN started
flashing red CAN error passive
solid red CAN bus off
1.4 Driver configuration
CAN-PRO1-PCIE is recognized by the driver automatically. Nothing more is usually required.
However, advanced configuration – like changing the name of a CAN channel or setting a
default baudrate - is possible with the Softing CAN Interface Manager.
•Click Start – All Programs – CAN – Runtime System Configuration – Softing CAN
Interface Manager (SCIM)
•For more details on the driver configuration click
Start – All Programs – CAN – Runtime System Configuration – SCIM_Manual
1.5 Application Software
How to use CAN-PRO1-PCIE and how to write application software, is described in the
Software Manual.
•To open this manual click
Start – All Programs – CAN – CAN_API - DOC – Softing Layer2
2 CAN Connector Pin Assignment
Connector pinning complies to CiA standard DS 102.
Pinning of the 9 pin
D-Sub connector
3 Status LED
The CAN channel has a status LED that
shows its current status .
4 RoHS Information
CAN-PRO1-PCIE is RoHS compliant.
Pin Signal
1 N.C.
2 CAN_L
3 Isolated GND
4 N.C.
5 Drain connected to connector
shield (1M/2.2n to isolated GND)
6 Isolated GND
7 CAN_H
8 N.C.
9 N.C.

Page: 4
5 CE Information
This device complies with the requirements of the EC directive 2004/108/EC
"Electromagnetic Compatibility" (EMC directive).
The product meets the following requirements:
•Emission: EN55022 Class B (ITE Product Standard)
•Immunity: EN61000-6-2 Generic Immunity Standard (industrial environments)
A "Declaration of Conformity" in accordance with the above standards has been made and is
filed at Softing Industrial Automation GmbH, Germany.
NOTE:
•To satisfy the EMC requirements, the equipment used (PC, monitor, CAN stations, etc.)
also has to meet the EMC requirements. A shielded cable must be used. In addition, the
cable shield must be grounded properly.
6 Technical data
•Unit: PCI Express card, acc. to PCIe specifications r1.0a and CEM 1.1
•CPU: XC161, 40 MHz with internal TwinCAN CAN controller
•Memory: 256 kbytes XC161 on-chip Flash, 512 kbytes RAM,
•PC interface: PCI Express, single lane, 512 kbytes shared RAM
•PC interrupt: controlled by the operating system
•CAN interface: galvanically isolated (1kV) CAN high speed according to
ISO 11898-2
•CAN connector: Sub-D 9 pin male, pin assignment acc. to CiA DS102
•Baud rate: 3.125 kbit/s up to 1 Mbit/s
•Power supply: +12V (±5%); typ. 60 mA
+3.3V (±5%); typ. 500 mA
•Temperature range: Operation: 0°C … 70°C (board ambient, i.e. inside the PC)
0°C … 55°C (typ. PC ambient)
Storage: -20°C … 70°C
•Relative humidity < 90% (non-condensing)