Solaire Medical InnerSpace User manual

Tools needed:
• Drill with #2 Phillips bit or a Phillips screwdriver
• 9/64" Allen wrench
• Level
Attachment hardware included
Step 1
• Loosen, but don’t remove, the 8 screws on the scope manager module.
Step 2
• Slide the scope manager module down the center guide rail to the
lowest position in the cabinet.
Step 3
• Remove the 3 mounting screws on the center guide rail and
remove the rail.
Scope Drying Retrofit Kit for Cabinets with Single Scope Manager
Follow these instructions to install a scope drying unit inside an Evolve cabinet with adjustable scope managers,
cord retainers, and AireCore construction.
Additional installation of filters, electrical components and connections, and training is provided onsite by a product
representative. Call your local sales representative or Customer Service at 888-435-2256 for assistance.
Step 4
• Attach the retrofit guide rail to the top 2 holes in the cabinet
with 2 screws.
Step 5
• Slide the scope manager module into place and tighten the 8 screws.
Step 6
• Use a level to ensure that the module height is even across the cabinet.
Continued on back
Solaire Medical | P.O. Box 2808 | Grand Rapids, Michigan 49501
888-435-2256 phone | 616-743-5944 fax | solairemedical.com
Storage solutions for healthcare © 2019 Solaire Medical, Grand Rapids, MI 49501
® InnerSpace is a registered trademark of Solaire Medical, Grand Rapids, MI 49501
0519
Loosen scope cue adjustment
screws (8X)
Dri Scope Retrot Kit Instructions
Tools Required: Phillips drive & 9/64” hex key
Remove center guide rail
mounting screws (3X)
Remove center guide rail
Attach retrot guide rail using the
same screw holes and screws (2X)
in back panel
Slide scope cue into place and lock
them down by tightening the
screws (8X)
Loosen scope cue adjustment
screws (8X)
Dri Scope Retrot Kit Instructions
Tools Required: Phillips drive & 9/64” hex key
Remove center guide rail
mounting screws (3X)
Remove center guide rail
Attach retrot guide rail using the
same screw holes and screws (2X)
in back panel
Slide scope cue into place and lock
them down by tightening the
screws (8X)

Step 7
• Remove the 5 screws from the underside of the cord retainer bracket
and remove the cord retainer.
Step 8
• Attach the new cord retainer to the bracket using the 5 screws.
Step 9
• Position the pump 1½" from the upper left corner and 5/8" from the top
of cabinet and attach using 4 wood screws.
Scope Drying Retrofit Kit for Cabinets with Single Scope Manager
page 2
Step 10
• Position the manifold a minimum of 14" from the bottom of the pump to
the top of the manifold and attach to the 4 corners of the manifold with
4 wood screws.
Step 11
• Position the tubing management strip 17"-24" from the bottom of
the top manifold to the tubing management strip. Attach the tubing
management strip using 3 wood screws.
Solaire Medical | P.O. Box 2808 | Grand Rapids, Michigan 49501
888-435-2256 phone | 616-743-5944 fax | solairemedical.com
Storage solutions for healthcare © 2019 Solaire Medical, Grand Rapids, MI 49501
® InnerSpace and Cath Manager are registered trademarks of Solaire Medical, Grand Rapids, MI 49501
0519
11
2"
5
8"
14"
minimum
17"-24"
1
1
2"
5
8"
14"
minimum
17"-24"
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1