Solarcanopy MK7 User manual

USER
MANUAL
Our aim is to supply excellent service and provide long lasting quality security products
Please read contents of this user manual fully before proceeding.
We are always looking at new innovations so keep a look out for what’s next!
MK7 DOOR-GATE PADLOCK COVER OR ANTI LIFT SYSTEM
MK7
For assistance: 07847 511 968 or email [email protected]
We can deliver and fit at an extra charge contact us for more details
www.4tress4gates.com

01
OIL
REGULARLY
We must point out the importance of oiling your
padlock at least every three months just how
much depends on your location and weather
conditions.
Padlocks have internal ball bearings and pins
that can rust so always lubricate every season.
Personally we would suggest monthly checks
just to be sure!
FITTINGS YOU NEED TO PURCHASE FOR YOUR MK7
*4 x M10 mushroom head squared coach bolts
*. 4 x M10 nuts or anti tamper cone shear off nuts
(if fitting on a door )
*4 x Anti tamper cone shear off nuts
(if fitting to a gate )
* WE CAN SUPPLY THESE AT OUR WEBSITE WWW.4TRESS4GATES.COM
02
03
Fitting Hasp and Staple
There must be a 5 mm gap from the top inner dimension of the
container when using on our Mk7 right side anti lift (used on a left hung
door swinging outwards) See photos 1, 1a and 1b.
Alternatively a 5 mm gap from bottom inner dimension of container if
using our Mk7 left side anti lift (used on a right hung door swinging
outwards).
Product is for external opening doors, single internal opening gates and
has an anti lift system for gates with adjustable hook and band fittings.
Included in your MK7 kit
1 padlock
1 x pan head screw and bolt
1 x Adapted Fireman’s drop key with a hole pre drilled.
(This allows you to screw one key from the set of three inwards facing
towards the opposite side of the fireman’s drop key as illustrated 1a)
How to open padlock.
Extend the Fireman’s drop key through the front of container to locate
the key barrel on padlock.
Twist the handle anti clockwise 180 degrees then pull shackle bar
open towards frame of door remove padlock with key still connected.
Note: The key does not release when padlock is open as illustrated
1a.
To refit the padlock
Key remains in padlock and the shackle is open, place padlock
shackle through hole in staple then push in shackle to close padlock
then twist fireman’s handle clockwise 180 degrees then pull out key.
to close illustrated 1b, 05

We delivery our products a special way with our chosen courier APC.
Courier despatched orders of our product range are packaged in our
re-usable sturdy Dewalt Tough-system cases.
You will be contacted to confirm receipt of a key and cable tie sent to
you by recorded delivery.
This key is required for you to open the case when it's delivered. You
need to take your goods ordered and inspect, sign the delivery note for
the courier and put the key which is put back onto the padlock from the
case and place into the supplied bag inside the case. Close 2 metal
straps on the case and securely close the case with the supplied cable
tie.
Driver will return it back to us for our next fantastic customer like
yourself.
This method helps to save our planet and our environmental footprint.
04
1A
1B

GET TO GRIPS
WITH HOW THE
LOCK
OPERATES WITH
THE KEY AND
HOLDER
Why maintain your padlocks?
Your Padlock is kept out in the very cold
environment you should oil it regularly to
prevent getting the key stuck in the chamber
or worst still breaking the key in the barrel.
Why I need to know the correct procedure?
If more than one person needs to access the
building or gate get them to do the same
procedure to get to know how the lock
operates. The operation of the key and
fireman's holder can turn one way when
fitted (clockwise to close counter clockwise
to open), so fitting it correctly is an
important requirement in operating the
product.
Procedure and maintenance of padlock will
save you getting stressed! Last thing we
want is for you to lock yourself out of the
building! So please remember oil and test
monthly keeping the ball bearing and
locking mechanism rust free and remember
how the padlocks with handle works.
WHY NOT COLOUR
COORDINATE DOOR2 KEY?
05
Photo 1 on the left is MK7 kit without the padlock
attached showing the 5 mm gap between container
and hasp explained in section 06.
Also shows the supplied staple positioned
vertically on door frame as opposed to the staple
on image 2 showing staple horizontal on the door
frame.
Hasp with a horizontal cut out hole for the staple is not suitable for
our product only vertical cut out hasp will work. The padlock key
area once fitted would leave the padlock exposed to lock picking
and the image 2 is just for illustration purposes and does not form
part of the kit supplied.
2
1

IMPORTANT
INFORMATION
METAL DOORS MARK POSITION
AVOIDING LOCKS ON THE DOOR!
On left hung doors use right side anti lift
Mk7, you should have marked a 5 mm
gap horizontally below inner top
dimension of container fit the supplied
hasp to this line you will now have the
required 5 mm gap so when the hasp is
open it will not hit the top side of the
container. See photos 1, 1a, and 1b.
On right hung doors use a left side anti lift
MK7 but you should have marked a 5 mm
gap horizontally above inner bottom
dimension of container fit hasp to this line
and continue as mentioned in above 7A
instructions.
Fit Staple vertically to the door frame. See
photo 1.
The shackle of the padlock most be able to be pulled out
horizontally across the door frame.
Best method on a brick building is to line up the shackle
with the mortar bonding of brickwork from the start before
starting any other marking up or subsequent drilling on the
door then work around the other fitting procedure to
prevent having to create room for the shackle pull out.
Fit padlock and check Firemans
handle does not make contact with
the inner container dimensional 75
mm line that you have drawn on the
door when turning the handle left to
open or right to close. See photo
1a.
Remember key can only be
removed once padlock is closed,
Go back to Step 2: if you have
skipped that section.
Place Mk7 container onto the door
and secure with 4 x M10 mushroom
head squared cup bolts from the
outside of door and secure with 4 x
M10 nuts or 4 x tamper proof shear
off nuts inside the building or gate.
Congratulations your building or
gate is secure and protected from
attack with 4tress4gates®.
Hope we have made it a simple
affordable security solution to
protecting your assets. And
provides you with a long term return
of your investment with us.
We are a small company and would
like to continually to bring you good
quality products it help us if you
leave feedback and recommend our
services and products to others.
Thank you once again!
06
07A
07B
08
09
10
11
12
When fitting onto metal doors take care not to drill through lock mechanism near the handle or
other lever locking bars on top bottom or vertical edge of the door locks.
Drill a small pilot hole straight through, then check with something thin and rigid such as a
copper conductor pushed through the hole and bend it at least 10 mm. Twist around to make sure
you will not hit any locking mechanism inside the door structure and do the same for the other 3
holes. Then drill through with a 10 mm metal drill bit all 4 holes. Mark around the dimensions of
the container on the door internal and external. Now add a further 5 mm line top and bottom of
the inside dimension to make inner dimension 65 mm.
You need a simple outline of inner width on the door for step 7

SIMPLE AFFORDABLE
SECURITY
2
1
1A
1B
1A
1B
2
Image 2 on the left Photo
is just for illustration
purposes of a hasp with
horizontal cut out and
how the padlock when
fitted to the staple will be
vertical.
This type of hasp is not
suitable for our
product.
Free padlock as illustrated
will be part of the kit
supplied.
Free fireman’s drop key as
shown connected to
padlock is part of the kit
supplied.
Free pan head screw and
bolt as shown is part of the
kit supplied.
13

USER
MANUAL
MK7
Solarcanopy Ltd. Registered Office: 16 Perry Wood Road, Great Barr, Birmingham. B42 2BQ
www.4tress4gates.com
Registered in England and Wales. No.05938901
For assistance: 07847 511 968 or email [email protected]
We can deliver and fit at an extra charge contact us for more details