TownSteel e-Elite 3000 User manual

TownSteel
e-Elite 3000
Installation Guide

Table of Contents
Package Content 2
Getting Started 3
Door Preparation 4
Step 1 - Latch Bolt & Strike 5
Step 2 - Installing Outside Assembly 6
Step 3 - Installing Backplate 7
Step 4 - Connecting Wires 8
Step 5 - Installing Inside Assembly 9
Step 6 - Installing Covers 10
Step 7 - Installing Inside Lever 11
Addendum 12
Exploded View 13
Troubleshoot 14
1

Outside Assembly
Backplate
Inside Assembly
Inside Lower Cover
Latch Bolt & Screws
Strike & Screws
Backplate Screws
Additional Parts Included
Inside Assembly Screws
Inside Cover Screw
Package Content
Parts in the box
Inside Upper Cover Collar Bearing Ring Inside Lever

Getting Started
Tools needed for lock installation
Phillips Screw Driver (Not included)
Lever Removal Tool
Torx Wrench
Note:
Do not use a power drill for installation of lock - it can damage the lock.
Handing Information

Door Preparation
Prepare door and jamb per template provided. The backset is the
dimension from the edge of the door to the centerline of the lock.
Important:
Door stop is where
the door will stop when
normally operated.
The stop includes any
gasket, smoke seal, or
bumpers. The position
of strikes are to be
measured taking this
into account.

Step 1
Install the latch bolt and secure with 2 screws. Install strike and
secure with 2 screws.
Note: A right hand (RH) lock will be depicted in the following guide - for left
hand (LH) install opposite. During installation keep the door open. Do not
use power tools for assembly or you can potentially damage the door.
Outside Inside

Step 2
Install the outside lock assembly in the cutout. Guide the wire
harnesses through the cutout. Line up the retractor on the lock
body with the latch tail piece. Tighten the latch screws.
Note: Do not pull or pinch the wire harnesses.
Bearing ring
should sit flush
on outside lock
assembly
Latch
tail piece
Retractor

YW1930

Step 4
Plug in the wire harnesses where indicated on the inside assembly.
Inside
assembly Motor
plug
Remote access
plug
Keypad
plug
Keypad
conn
Motor
conn

Step 5
Install inside assembly with 4 screws. Do not pinch wires. Install the
4 AA alkaline batteries provided. The keypad will light up green and
the motor will run.

Step 6
Install inside lower cover first. Tighten the bearing ring to hold
cover in place. Install the inside upper cover - slide down from top -
secure with screw using the wrench provided.
Inside upper cover
Torx
wrench
Lever removal
tool
Inside lower
cover
Bearing ring

Step 7
Install the inside lever - ensure the lever is seated and is locked
in place. Lever catch is on the side of lever and it should snap into
place.
Note: Check lock for correct operation before closing the door.
See programming guide for help.

Addendum
2. Insert lever removal tool into the
lever catch hole and push back
the lever catch.
Lever
catch
hole
3. Remove lever.
12

Exploded View
1 x Inside
Cover Screw
Inside Upper
Cover
Inside
Lever
Bearing
Ring
Inside Lower
Cover
4 x Inside
Backplate
Assembly Screws
Inside
Assembly
Collar
Outside
Assembly
2 x Backplate
Screws Latch Bolt
2 x Latch Screws
13

Troubleshoot
Problem Cause Solution
Keypad does not light up. Batteries are dead.
Keypad is locked out due to
amount of incorrect codes
Not fully plugged in wires or
pinched wires.
Replace batteries by removing
back cover.
Wait 60 seconds and try again.
Check wire connection.
Issues retracting latch.
Keypad lights up but motor
does not respond.
Latch tail piece did not fully
engage lock body retractor.
Motor wire is not fully plugged
in or has been pinched.
Motor wire was plugged into
the wrong plug.
See Step 2.
Undo the back cover and
inside assembly. Inspect the
motor wire.
See Step 4.
14

VISIT WWW.TOWNSTEEL.COM FOR
17901 RAILROAD STREET
CITY OF INDUSTRY, CA 91748
TOLL FREE: 877-858-0888
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
RF Exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure compliance.