DynaLock 3001 TJ31 Series User manual

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 1
Familiarize yourself with the door and frame conditions. The lock must mount rigidly to the face of the door frame
header. The door mounted armature is supplied with an adjustable mounting bracket and hardware that allows it to
pivot slightly to compensate for reasonable misalignment.
Care must be taken that the lock face and armature face are kept free of dirt, rust, paint, or any other obstruction
which may interfere with the lock and armature making good contact. These faces may be cleaned with a non-
abrasive pad and wiped with an oil dampened cloth.
The Series 3001xTJ31 is a 700 pound holding force top jamb-mounted electromagnetic lock designed to secure a
double-inswinging pair of doors. The lock requires both installation procedures as described herein and in the
separate wiring instructions included.
Typical installations of the lock on double-inswing doors:
HANDLING
MECHANICAL INSTALLATION
ELECTRICAL INSTALLATION
After mechanical installation is complete the lock needs to be wired to a 12 or 24 VDC/VAC power source. Once low
voltage power is supplied the unit is fully operational. All other wiring is for selected options. Refer to the separate
wiring instructions included for further information.
INSTALLATION DESCRIPTION

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 2
L
MOUNTING CONSIDERATIONS
INSTALL THE LOCK ASSEMBLY
Individual door and frame conditions
may vary. Dimensions shown at right
are for a typical hollow metal door and
frame.
The lock assembly should be mounted
to the center of the frame header for
maximum performance. Verify that
there is proper clearance for the lock
assembly at the planned mounting
location.
1.
2.
Drill out the four dimpled mounting hole locations inside the
back of the lock housing using a 3/16” drill. Position the lock
assembly on the face of the frame header, on the pull side of
the door, as shown. Locate and mark the centers of the four
mounting holes.
Drill the marked holes in the face of the frame header:
a. Four (4) 1/8” dia. slotted mounting holes, 1” deep.
Attach the lock mounting bracket to the frame header using
four (4) #10 x 1” pan head Tek screws. Firmly tighten the
screws using a #2 phillips screwdriver.
1.
2.
3.
2-7/16”
ARMATURE
LOCKASSEMBLY
1/8” GAP
1/8” GAP 5”
REF
1-1/4”
ARMATUREBRACKET
MOUNTING SCREW
DOOR
1/8”
ABOVE
HEADER
RABBET
MOUNTING HOLES
CENTERLINE
4-9/16”

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 3
ATTACH THE ARMATURES TO THE ARMATURE MOUNTING BRACKETS
ASSEMBLE THE ARMATURE MOUNTING BRACKET
Using the two lock mounting screws and
brass spacers attach the lock assembly to
the lock mounting bracket as shown. The
lock assembly will need to be removed later
to add the remaining bracket mounting
screws,afterallhardwareadjustmentshave
been made.
Firmly tighten the mounting screws with a
3/16” hex wrench.
BRACKETASSEMBLYSCREW
UPPERARMATUREBRACKET
LOCK WASHER
ARMATURESPACER
FLAT STEEL WASHER
RUBBERWASHER
ARMATURE
MOUNTING
SCREW
ARMATURE MOUNTING BRACKET
Locate the armature mounting hardware
from the hardware kit and attach the
armaturestothearmature mounting bracket
as shown. Firmly tighten the mounting
screws with a 3/16” hex wrench.
Failure to properly secure the armatures
to the brackets could result in serious
injury or possible security breach.
LOWER ARMATURE BRACKET

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 4
L
L
INSTALL THE ARMATURE MOUNTING BRACKETS
From the illustrations below select the one that resembles your door type and follow the instructions for drilling the
two (2) armature mounting bracket screw holes on each door leaf.
Use the figure below to identify and mark the locations of the armature mounting bracket screw holes on each door
leaf. Refer to door and frame prep drawing #301095 for further information.
ARMATURE BRACKET
MOUNTING SCREW
LOWER
ARMATURE
MOUNTING
BRACKET
21/32”
SEX
NUT
DOOR
SPACER
ARMATURE BRACKET
MOUNTING SCREW
LOWER
ARMATURE
MOUNTING
BRACKET
1/2”
1”
ARMATURE BRACKET
MOUNTING SCREW
LOWER
ARMATURE
MOUNTING
BRACKET
5/16”-18THREAD
Drill an 11/32” diameter hole
throughdoor.Fromsex nutside
only enlarge the 11/32” hole to
21/32”diameter.
Drill an 11/32” diameter hole
throughdoor.Fromsex nutside
only drill 1/2” diameter hole to
1”depth.
Drillan11/64”diameterholeand
tapfor 5/16”-18 thread.
GLASS& ALUMINUM
OR HOLLOW METAL DOOR SOLID CORE DOOR REINFORCEDDOOR
1.
2.
Mount the armature and mounting bracket assemblies to each door leaf using the appropriate hardware for you
door type. Frimly tighten the mounting screws with a 3/16” hex wrench.
3.
1-3/8”
FROM
FRAME
RABBET
3/4” FROM
CENTER OF
OPENING
3/4” FROM
CENTER OF
OPENING
2-1/4”
2-1/4”
CENTERLINE

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 5
ARMATURE ADJUSTMENT
Using a 5/32” hex wrench temporarily loosen the
armature bracket assembly screws roughly 1-1/2
turns to allow the upper armature bracket to move
in and out freely (Ref. Figure “A”).
Close and latch the door. The mating surfaces of
the lock and armatures should fully contact each
other. If necesssary slide each armature in or out
to ensure full contact is made with the lock while
still allowing the door to properly close and latch.
When the desired adjustment is acheived slowly
open each door, taking care to maintain the
position of the armature. Firmly tighten the
armature bracket assembly screws with a 5/32”
hex wrench, making sure that the locking ribs on
theupper and lowerbracket halves properlymesh
(Ref. Figure “A”).
1.
2.
3.
ARMATURE
ARMATURE BRACKET
ADJUSTMENT RANGE
0” 1”
Figure “A”
ASSEMBLY SCREW (TYP.)

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 6
EXPLODED PARTS VIEW LEGEND
Lock Assembly
Armature
Upper Armature Bracket
Lower Armature Bracket
Access Cover / Board Assy.
Access Cover Screw
End Cover
1
2
3
4
5
6
7
Consult Factory
300013
300783
300782
300906
300608
300010
8
9
10
11
12
13
14
15
16
17
Armature Bracket Assy. Screw
Lock Washer
Lock Mounting Screw
Armature Mounting Screw
Armature Spacer
Rubber Washer
Flat Steel Washer
Sex Nut
Door Spacer
Armature Bracket Mtg. Screw
ITEM DESCRIPTION PART NO.
ITEM DESCRIPTION PART NO.
Hardware Kit
P/N 301096
Note: Refer to Page 7 for parts locations.

DynaLock
705 Emmett Street ?Bristol, CT 06010
Ph/ 860.582.4761 ?Fx/ 860.585.0338
SERIES 3001xTJ31
ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
3001xTJ31 MANUAL - FORM 3001TJ-001 11/02Page 7
EXPLODED PARTS VIEW
Note: Refer to Page 6 for parts legend.
LOCK
ASSEMBLY
ARMATURE
ASSEMBLY
(TYPICAL)
213
7
6
1
8
9
12
10
11
4
3
17
14
5
15 16
6

FOR PRODUCT SUPPORT AND PARTS
ORDERING INFORMATION CONTACT:
DynaLock Corp.
705 Emmett Street
Bristol, CT 06010
Bus: [phone] Toll-Free
[phone]
Fax: [phone]
DYNALOCK ON THE INTERNET:
E-mail: [email protected]
Website: www.dynalock.com
2011TJ/3003LC MANUAL - FORM 2011TJ-001 04/02
Page 8

PLEASE READ BEFORE ATTEMPTING INSTALLATIONS
3000/ 3000LC/ 2000/2050/2280 SERIES
CIRCUIT BOARD DESCRIPTION
Refer to Page 2 & 3 for wiring instructions
1 Rev.B
DynaLock Corp. 705 Emmett Street P.O. Box 2728 Bristol, CT 06011-2728Phone [phone] Fax [phone]
DynaLock Electromagnetic Locking Systems

2 Rev. B

3 Rev. B

4 Rev. B