Soleus Air SPORTS STRAP User manual

USER MANUAL

Scan the QR code on the left and
download the APP installation.
On Android or iOS phones, use
them.
Please use the product for the first time to ensure that
the battery is normal. If the battery is low and not working
properly, please connect the charger to charge the device,
and the bracelet will automatically turn on (charging
method as shown below).
IOS system 9.0
or above
Android system 4.4
or higher
Mobile phone
hardware supports
Bluetooth 4.0
1>Download“Dafit”
2>Product activation and charging
Mobile phone system hardware platform
needs to meet the conditions
APP installation and device binding

Open the mobile client to set up personal
information
Switch to the "Device" page and click on
"Bind Device"
Click on your device in the list of scanned
devices
Binding is complete
Please make sure the app is installed on your phone，Click
on the "Dafit" icon，Follow the instructions to open the
phone Bluetooth, and then proceed to the following process
Long press on the main interface of the watch, the watch
MAC address will be displayed, which can be accessed
through the device column.The MAC address in the table to
determine your device; After the watch is successfully bound,
the bracelet will be automatically connected to the phone
each time the client is opened.
Once the bracelet is successfully bound, you can start
recording and analyzing your movements and sleeps heart
rate, blood pressure, blood oxygen condition, under
normal circumstances, the order in which the watch are
switched is as follows:
One of the three interfaces (replaceable with the main
interface)
3>Bind the watch to the phone
Start using
1>Main interface (time interface)
10 10

1.1) The main interface slides down
enter the settings screen
enter the function operation interface
1.2) The main interface slides to the left
enter the multi-motion selection interface
1.3) The main bound slides to the right
enter the information interface
1.4) The main interface slides up

You don't need to
connect to an APP
to see your daily
steps, mileage and
calories burned.
2>Step gauge
interface
Without connecting
to the APP, you can
check your daily
sleep status, the
time of deep sleep
and light sleep, so
as to better monitor
your sleep.
3>Sleep interface
Monitor your heart
rate 24 hours a
day, so that you
can know your
heart rate anytime
and anywhere, and
better monitor
your heart rate.
4>Heart rate
interface

Long press to see a variety of motion patterns, in
different situations with different patterns to record;
Note: different motion patterns produce different motion
data
5>Multisport mode
Long press to enter other functions, you want the
function here
6>Other functions
Running
Cycling
Football
Basketball
Swimming
BP
Blood oxygen
Weather
Information
Camera
Stopwatch
Brightness
Theme
Walk
Badminton
Skipping

Need to open the function in the app
Open the app and click on the device ---> Daily Alarm
---> Set the alarm time.After setting, the watch end will
vibrate at the corresponding time.
1>Alarm clock function
Open the app and click on the device ---> Camera
Control ---> Enter the camera interface.After opening
the camera interface, the watch can be shaken to make a
large movie.
2>Photo control

About GPS trajectory description
When the mobile phone is not connected, the wristband
cannot obtain the weather information. When the watch is
connected to the mobile phone, the wristband will
automatically update the weather information according
to the setting city of your mobile phone.
Open the phone app
and click GPS to run
3>Weather function
1>Connect the mobile
phone with the device

The deviation of measurement values between smartwatch
and sphygmomanometer is caused by many factors. Firstly,
the sphygmomanometer measures the brachial artery, while
the smartwatch measures two main branches of the arteriole.
Normally speaking, the difference between the blood pressure
measurement values of aorta and that of arteriole is 30-40; if
1> Why is there a difference between blood pressure
values and sphygmomanometer?
2>Check the GPS signal is
normal, click to start.
3>Enter the GPS motion track,
you can switch the data mode
or map mode, and view the motion
route at any time.
4>After the exercise is over, click
and hold the stop button to end
the function.
Bracelet FAQ

you use the smartwatch and sphygmomanometer to measure
blood pressure at the same time, as the blood flowing
through the arteries is centrifugal, the band puts pressure on
the area below the middle of your elbow when using a
sphygmomanometer to measure blood pressure, so that the
blood cannot flow smoothly to the lower branches of the
artery temporarily; in this case, vascular tension will increase,
thus leading to greater deviation of pressure measurement
values.
As the temperature of bath water is quite high, there will be a
lot of stream. Moreover, as the steam is gaseous and its
molecular radius is small, it will easily infiltrate into the watch
through the gap. When the temperature drops, the stream
condenses back into liquid droplets, which will easily lead to
internal short circuit and damage.
Android system setting:
1.Please confirm that the message prompt function at the
mobile phone terminal is activated.
2.Please confirm that messages can be displayed normally in
the notification bar, for the messages that the smartwatch
receives from the notification bar. If there is no message in the
notification bar, then the smartwatch cannot receive any
message.
2>Why you can’t wear the smartwatch when
you take a hot bath?
3>Why the smartwatch can’t receive message prompt?