Solomon SL-916D User manual

Voltage
Power consumption
Temp.setting range
Heater Operating Voltage
Weight
Station-Handpiece cordlenght
AC Power Cord
Vacuum pump
110/120V AC or 220/240V AC
50W
24V AC
L218:W176:H145(mm)
5300g
115cm
3pin plug 180cm
-500mmHg 24V AC
Soldering
Desoldering
Station
160 C~480 C 320 F~900 F
o o o o
210 C~480 C 410 F~900 F
o o o o
SOLDERDESOLDER
SL-2 DESOLDER 24V 50W
Iron holder
Gun holder
Filter
Silicone hose
Cable
Desoldering GUN
Solder-temperat
ure adjustment
Desolder-tempe
rature
adjustment
Power switch
Cable
Handle
Collar
Heater w/sensor
Tip
Knurled nut
barrel assembly
Knurled nut
barrel assembly
Desoldering tip
Heater w/sensor
Glass tube
Filter
Pulling
TAP
POWER
T
W
4
8
V
4
-
I
S
2
L
E
N
R
I
T
SL-916D
SOLDERING & DESOLDERING IRON STATION
SOLDERING TIP 0.8mm 1 PC
SPARE PART:
NOZZLE CLEANING
¨0.7mm 1 PC
¨1.0mm 1 PC
¨1.2mm 1 PC
GLASS TUBE 2 PC
FILTER(SOFT) 10PC
FILTER(METAL) 5 PC
DESOLDERING TIP ¨1.5mm 1 PC
Pw400013-2015-11

Operation Instructions:
1. Insert plug into
2. Put the power switch on the location
of "ON".
The indicatorlightens, thenwait5
minutes before using in order to
avoid nozzle and pipe to be blocked
by tin chip and due to unsufficient
heating.
3. If there is any tin chip blocked in
the nozzle and pipe, pleasewait 5
minutes after the power switch
lightens, putneedleintonozzleand
pipe and clean left articles by
pulling backandforth.
(do cleaning when the vacuum pump
starts.)
4. Put the nozzle on the tin, which you
intend to take for 2-3 seconds, and
shake the nozzle, then the pins of IC
willmoveandtins have been melted.
After tin is melted, press thetri-
gger and start vacuum pump, then tin
willbeimmediatelyabsorbed. If tin
is not completed melted, the tin can
not be cleaned, of course parts are
not able to be taken down. In this
case, pleaseadd some solder and re-
peatthea/moperation instruction.
Maintenance:
ReplacementofFilter
If tins are filledinthefilting
pipe, the vacuum pressure willbe
pipe, the vacuum pressure willbe
decreased. Pleasereplace accor-
ding to the following instructions:
1. Put the buttonof"PULL"backward,
rotate 90 and then fix it.
2. You cantakeoutfilterbypulling
the pipe backwardandmoving away
fromthelocationof"O"ring.
3. Cleanthetinchipinfiltingpipe.
4. If there is too much tin in the
first layer steel fibre filterand
the filterhas beenusedmany
times, pleasereplace anewone.
Pleasealsoreplace anewfilter,
when the second-layer-filter
absovbs soldering flux fully.
5. When doing replacement, the first
layer steelfibrefiltershouldbe
put beside the nozzle and the
beside the pump.
* Pleasedo not use vacuum pump, if
there is no filter.Thevacuumpump
willbeoutoforder, when you start
vacuum pumpwithoutputtingfilterin.
Pleasedo not use the desolder, when
the filteris not installed.
* If the supply cord is damaged, it must
be replacedbythemanufacturer. its
service agentorsimilarlyqualified
persons in order to avoid a hazard.