manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Edsyn
  6. •
  7. Soldering Gun
  8. •
  9. Edsyn 971 LONER User manual

Edsyn 971 LONER User manual

971 LONER®
high performance
Temperature Controlled
SolderingStation
SPECIFICATIONS
• 120V, 50/60Hz, 70W, 2.5 lbs. (1.13 kg.)
• COMPLIES WITH DOD-STD-2000-1B, MIL-STD-
2000A and ESD SPEC. DOD-STD 1868, DOD-
HDBK-263
• TEMP. RANGE: 400°F - 800°F (205°C - 427°C)
• TEMP. REGULATION: ±6°F (±3°C)
• TIP TO GROUND LEAKAGE: < 2MV
• TIP TO GROUND RESISTANCE: < 2 OHMS
• UL LISTED
made
in
U S A
Static Safe
1. Turn on powerand set Temperature
Control Knob to 400°F.
2. Using a clean and well tinned Tip,
apply a small amount of solder on the
Tip, just enough to form a bead on top
of the Tip.
3. Place the center of the thermocouple
wire of theSDS100 on top of the bead.
4. Again, apply a small amount of solder
on the center of the thermo-couple
wire, just enough to embed the center.
5. Adjust LO-Temp. Calibration Pot so the
Meter will read 400°F.
6. Set Temperature Control Knob to 800°F.
7. Adjust Hi-Temp. Calibration Pot so the
Meter will read 800°F.
AIR MOVEMENT WILL AFFECT THE TEMPERATURE READING.
WORK IN AN AREA WHERE THIS IS MINIMAL.
MS412
Temperature
Calibration System
SDS100
FX635
TEMPERATURECALIBRATION
TIP CARE
1. Set desired temperature. Blinking
Lamp means Tool is regulating.
2.TIN the Tip. (apply solder)
3.Do not rub, bend or reshape the Tip.
4.Always clean the Tip by wiping it
against the saturated sponge and
always RE-TIN.
Temp. Control
Hi/Lo Temp. Calibration Pot
Temp. Regulation
Indicator
Sponge Holder Power Switch
Loosen RCS71
Collar by turning
counter-clockwise
and pull the Tip
straight out.
Direct Tip/Heater
Contact PD528
Tool Pod
WARNING: DO NOT HIT OR TAP THE
TOOL. HEATER ELEMENT WILL BREAK!!!
To replace Pod,
press Release Tab
and slide out Pod.
1
a
971 LONER®High Performance
SOLDERING STATION
SPARE PARTS LIST
4
a
i
h
d
e
f
abc
7
11 5
32
13
d
c
b
9
24
6
20 21
17
17a
16
19
25 23
7
9
15
18
14
10
j
g
c
22
12
b
C:\PM6\SERVICE\971.PM4
Rev C
1 PD528 Tool Pod 1
1a SR042 Thermal Housing for Tool Pod 1
1b SC581 Solder Collector for Tool Pod 1
1c SR043 Front Housing for Tool Pod 1
2SH230 General Purpose Sponge Holder 1
2a RS199 Cleaning Sponge 1
2b RS243 Leveling Pad for SH230 1
2c LN230 Liner for SH230 1
2d SH230-1 Sponge Holder Tray 1
3SR577 Control Panel Label 1
4SR065 Power Switch, Illuminated 1
5SR045 Knob, Temperature Control 1
6SR243 5K Potentiometer, Temperature Control 1
7SR015 Flat Head Screw- Slotted #6 - 32 x 1/2 4
9 SR467 Hex Nut, Square Cone- #6 - 32 4
10 SR741 Top Base 1
11 SR019 Dove Tail Mount 1
12 15002W95 Circuit Board 1
13 SR573 LED Assy. Front Panel Mount 1
14 SR611 Bottom Base 1
15 SR011 Pan Head Screw- Phillip #6 - 18 x 5/8 4
16 SR054 Bottom Weight 1
17 SR252 Power Cord Assy. 1
17a SR026 Power Cord only(Connectors not included) 1
18 SR251 Rubber Foot 4
19 SR226 Strain Relief Block for Tool Cord(Tool & Cord Assy. not included) 1
20 SR241 Strain Relief for Power Cord 1
21 SR249 Fuse, 250V, 1.6 A (5mm x 20 mm) 1
22 SR575 Soldering Tool, Complete Assembly 1
22a SR579 Handle for Tool 1
22b SR058 Cord Strain Relief 1
22c SR280 Tool Cord, Burn Proof(Connector Assy. on one end) 1
22d SR574 Heater Assembly 1
22e LTC71 Tip Collet 1
22f RCS71 Retaining Collar and Sleeve 1
22g LT375 LONER®Standard Spade Tip 1
22h SR001 O-Ring, Silicone, .30 ID 1
22i SR240 O-Ring, For Handle, .50 ID 1
22j SR525 Hose, Low Static, 1/4 I.D.(sold per foot) 51/4"
23 SR301 Plug, Covering for Strain Relief, Tool Cord Outlet 1
24 SR255 Spacer for Potentiometer 1
25 SR310 Label, Set Pot, Right Front or Left Rear 1
ITEM
NO. PART NO. DESCRIPTION QTY
REQ'D
15958 ARMINTA ST. VAN NUYS, CA 91406-1896
PHONE: (818) 989-2324 FAX (sales): 818-997-0895
Email: [email protected] Internet: www.edsyn.com© Copyright EDSYN,Inc.1998
REPLACING TIPS
LN230
SH230-1
CAUTION:
Over- lling can cause t hermal shock to the tip
or heating element during tip cleaning.
RS243
RS199
• Replace RS199 Cleaning Sponge
1. Fill water only up to the top of theRS243 Leveling Pad.
2. DepressRS199 to moisten it completely.
• Replace SC581 Solder Collector
1. Hold the Housing rm and turn Cap counter-clockwise
and pull it away from the Housing.
2. Remove usedSC581 and replace with a new one.
3. Reassemble Pod with TOP of the Cap in proper position.
MAINTENANCE
SC581 SR043
Front HousingSR042
Thermal Housing
CAUTION
1. Tool must be cool when changing tips.
2.Do not twist or wiggle the tip.
AFTER TIP IS INSTALLED, TIGHTEN COLLAR PROPERLY.
Loosen RCS71 Collar by turning coun-
ter-clockwise and pull the Tip straight
out.
Part No. & Description a b
LT374 Standard Probe .03 (0.8 mm) .48 (12.2 mm)
LT375 Standard Spade .06 (1.5 mm) .48 (12.2 mm)
LT376-7 SMD Channel .12 (3.0 mm) .48 (12.2 mn)
LT392 Extra-Long Needle .02 (0.5 mm) 1.13 (28.8 mm)
LT394 Extra-Long Spade .07 (2.0 mm) .93 (23.6 mm)
LT399 Large Face .17 (4.3 mm) .49 (12.4 mm)
LT444 SMD Mid-Length Fine Spade .04 (1.0 mm) .78 (19.8 mm)
LT446 SMD Probe .03 (0.8 mm) .48 (12.2 mm)
LT382 Long Cone .02 (0.5 mm) .62 (15.6 mm)
LT395 Mid-Length Stubby Spade .09 (2.3 mm) .74 (18.8 mm)
LT431 Mid-Length Spade .07 (1.8 mm) .74 (18.8 mm)
LT439 SMD Thin Probe .03 (0.8 mm) .50 (12.7 mm)
LT439-1 Same as LT439, Angled
LT445 SMD Angle Face .03 (0.8 mm) .48 (12.2 mm)
General Purpose Soldering Tips
Iron Plated for long life•Nickel and Chrome Plated for optimum heat transfer.
EDSYN has over a 100 varieties of standard and custom-made Tips. CONTACT EDSYN FOR MORE SELECTIONS.
LTC71 RCS71
FORM.922
Rev C

Other Edsyn Soldering Gun manuals

Edsyn Loner CL1180 User manual

Edsyn

Edsyn Loner CL1180 User manual

Edsyn ZD905 User manual

Edsyn

Edsyn ZD905 User manual

Edsyn LONER 971DX User manual

Edsyn

Edsyn LONER 971DX User manual

Edsyn LONER 971DF-230 User manual

Edsyn

Edsyn LONER 971DF-230 User manual

Edsyn CL1080 LONER User manual

Edsyn

Edsyn CL1080 LONER User manual

Edsyn CL1280 LONER User manual

Edsyn

Edsyn CL1280 LONER User manual

Edsyn 971-230 LONER User manual

Edsyn

Edsyn 971-230 LONER User manual

Edsyn 971E LONER User manual

Edsyn

Edsyn 971E LONER User manual

Edsyn SOLDAVAC VA175 Operating and maintenance manual

Edsyn

Edsyn SOLDAVAC VA175 Operating and maintenance manual

Edsyn LONER 951SX-H10 User manual

Edsyn

Edsyn LONER 951SX-H10 User manual

Edsyn 981C-230 User manual

Edsyn

Edsyn 981C-230 User manual

Edsyn LONER 951SX-230 User manual

Edsyn

Edsyn LONER 951SX-230 User manual

Edsyn 971DX-230 User manual

Edsyn

Edsyn 971DX-230 User manual

Popular Soldering Gun manuals by other brands

Elenco Electronics SL-5 instruction manual

Elenco Electronics

Elenco Electronics SL-5 instruction manual

Velleman BITS5 quick start guide

Velleman

Velleman BITS5 quick start guide

BlackJack SolderWerks BK8000 instruction manual

BlackJack SolderWerks

BlackJack SolderWerks BK8000 instruction manual

ETT Distribution MLS-48 owner's manual

ETT Distribution

ETT Distribution MLS-48 owner's manual

REMS Contact 2000 instruction manual

REMS

REMS Contact 2000 instruction manual

jcb CA Series instruction manual

jcb

jcb CA Series instruction manual

Metcal GT90 quick start guide

Metcal

Metcal GT90 quick start guide

WilTec 61538 Operation manual

WilTec

WilTec 61538 Operation manual

Weller WDD 161V operating instructions

Weller

Weller WDD 161V operating instructions

Duratool D03168 quick guide

Duratool

Duratool D03168 quick guide

Tronair MALABAR 150-5 Operation & service manual

Tronair

Tronair MALABAR 150-5 Operation & service manual

Weller WMD 3 operating instructions

Weller

Weller WMD 3 operating instructions

jbc RWB-A manual

jbc

jbc RWB-A manual

STANNOL INDUSTA HF operating instructions

STANNOL

STANNOL INDUSTA HF operating instructions

Würth Powerjet Translation of the original operating instructions

Würth

Würth Powerjet Translation of the original operating instructions

Velleman VTSSC30N user manual

Velleman

Velleman VTSSC30N user manual

Weller WR 2 Translation of the original instructions

Weller

Weller WR 2 Translation of the original instructions

Atten ST-2090D user manual

Atten

Atten ST-2090D user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.