Sony Ericsson XPERIA acro HD IS12S Guide

Cautions on using IS12S
Safety Precautions (Observe Strictly)
Handling precautions
Specific Absorption Rate (SAR) of cell phones
Intellectual property rights
・Company names, product names and system names referred to in this
manual are generally trademarks or registered trademarks of respective
companies. The TM, ®marks may be omitted in this manual.
・In this manual, "Setting Guide", "Start Guide", "取扱説明書詳細版(Full
Instruction Manual)" (Japanese), "Cautions on using IS12S", "携帯電話の比吸
収率などについて(Radio Frequency (RF) exposure and Specific Absorption
Rate (SAR))" are collectively referred to as "Instruction Manual".
・In this manual, "XPERIA acro HD IS12S" is usually referred to as "IS12S" or
"the product".
February 2012, 1st Edition 1263-3424.1
■Before using this product, thoroughly read these safety precautions
for proper use. After reading, store the precautions in a safe place.
●These "Safety Precautions" describe instructions that should be observed to
prevent damage to property or injury to the customer or others using IS12S.
●These instructions are divided into the following categories.
■Explanation of indications used in this manual
*1 Serious injury: This refers to loss of sight, injury, burns (high- and low-
temperature), electric shock, broken bones, injuries with
residual aftereffects from poisoning, etc., and injuries
requiring hospital admission for treatment or long-term
hospital attendance as an outpatient.
*2 Injury: This refers to injuries, burns (high- and low-temperature),
electric shock, etc. that do not require hospital admission for
treatment or long-term hospital attendance as an outpatient.
*3 Physical damage: This refers to extended damage to buildings, furniture,
livestock, or pets.
■Explanation of graphic symbols
■Precautions common to the IS12S main unit, battery pack,
charging equipment, au IC-Card, peripheral devices
Be sure to read this manual before use.
Safety Precautions (Observe Strictly)
This symbol indicates the potential and imminent
danger of death or serious injury (*1) to a person.
This symbol indicates the possibility of death or serious
injury (*1) to a person.
This symbol indicates the possibility of personal
injury (*2) to a person or physical damage (*3).
Indicates an action that is
not allowed.
Indicates that use in a place
where the product is likely to
get wet is not allowed.
Indicates that disassembly
is not allowed.
Indicates an action that
must be done.
Indicates that handling with
wet hands is not allowed.
Indicates that the power
plug must be disconnected
from the power outlet.
Danger
Warning
Caution
Don't No liquids
No disassembly
Do
No wet
hands
Unplug
Be sure to read the following hazards before use.
Be sure to use only the exclusive peripheral devices. Use of other
peripheral devices might cause overheating, fire, rupture, fault, or
leakage of liquid.
Specified and common peripheral devices for IS12S:
・Sony Ericsson AC adapter 04 (EP800A)
・Desktop Holder (DK200)
Do not use, store or leave the product in hot places (e.g. by the fire,
near a heater, under a kotatsu, in direct sunlight, in car in the hot sun).
Doing so might cause ignition, rupture, fault, fire or injury.
Before entering an area where flammable gas is generated such as a
gas station, be sure to turn off IS12S. Do not charge the battery.
Failure to do so might cause the gas to catch fire. In addition, when
using Osaifu-Keitai®at a gas station, be sure to turn off the power in
advance. (If Osaifu-Keitai lock has been set, cancel the lock before
turning off the power.)
Do not put the product in a cooking apparatus such as microwave
oven or a pressure vessel. Doing so might cause ignition, rupture,
fault, fire or injury.
Do not throw the product into a fire or heat it. Doing so might cause
ignition, rupture or fire.
Do not short-circuit the desktop holder connection terminal, microUSB
connection terminal, headset connection terminal, or HDMI
connection terminal. Do not allow conductive foreign objects (metal
fragments, pencil leads, etc.) to come into contact with or get inside
the desktop holder connection terminal, microUSB connection
terminal, headset connection terminal, or HDMI connection terminal.
Doing so might cause fire or a fault.
When using a metal strap or accessory, take sure not to allow the metal
part come in contact with the microUSB connection terminal or AC
adapter power plug. Doing so might cause electric shock, ignition, injury
or a fault.
Danger
When plugging the AC adapter into an outlet, do not allow a metal
strap or accessory come in contact with the power plug. Doing so
might cause fire, electric shock, injury or a fault.
Do not expose the camera lens to direct sunlight for an extended
period. Doing so might cause ignition, rupture or fire by the light-
collecting mechanism of the lens.
The customer is not allowed to disassemble, modify or repair the
product. Doing so might cause a fault, iginition, electric shock, or injury.
The Company is not liable even in the event of any nonconformities
arising on IS12S or peripheral devices as a result of modification, etc.
Modification of the product is in violation of the Wireless Telegraphy Act.
Be sure to read the following warnings before
use.
Do not drop or subject to strong impact, such as throwing. Doing so
might cause rupture, overheating, ignition, leakage or a fault.
Do not use outside when you can hear thunder. Doing so might risk
lightning strikes and electric shock.
Do not let your hands, fingers and other parts of the body touch the
desktop holder connection terminal, microUSB connection terminal,
headset connection terminal or HDMI connection terminal. Doing so
might cause electric shock, injury or a fault.
If IS12S is damaged because it is dropped or something, and its
display is cracked or internal parts are exposed, do not touch the
cracked display or exposed parts with your hands. Doing so might
cause electric shock or injury from damaged parts. Contact an au
shop or Customer Service Center.
Although IS12S has waterproof property, stop use if liquid such as
water gets inside the main unit from the microUSB connection
terminal, headset connection terminal, HDMI connection terminal,
microSD memory card insertion slot, au IC-Card slot, etc. Continued
use of the product in this state might cause overheating, fire or a fault.
Warning
■IS12S Main unit
Never charge the battery if the IS12S main unit is wet. Doing so might
cause electric shock or short circuit resulting in a fault or a fire. Faults
caused by wetting with water are not covered by the warranty and
repairs cannot be performed.
If charging is not completed after the specified charging time, stop
charging. Failure to do so might cause leakage, overheating, rupture
or ignition.
Be sure to read the following cautions before
use.
Do not store the product in places subject to direct sunlight (e.g. in
car), places that get hot, places that get extremely cold, and in humid
or dusty places. Doing so might cause overheating, ignition,
deformation or a fault.
Do not leave on unstable places such as rocky stands or tilting surfaces.
Dropping the product may cause injury or damage. Also, pay sufficient
attention to impact, etc. Be careful in particular when vibration is set.
Do not cover or wrap the product with bedding, etc. while using or
charging the product. Doing so might cause fire, fault or injury.
Do not leave in places within the reach of small children. Small children
might swallow small parts, etc. by mistake and choke on them, or
might drop the product by mistake and cause accidents or injury.
Children using the product should be instructed in proper operation to
avoid danger by an adult. Do not allow them to use the product
without adult supervision. Failure to do so might cause injuries.
Do not touch the IS12S main unit or AC adapter for a long time while
power is being supplied from an external source. Doing so might
cause low-temperature burns.
When using IS12S touching your skin such as putting the product in a
pocket, it may cause low-temperature burns depending on how the product
touches your body, how long it lasts or how the surrounding conditions are.
In particular, when using a heating apparatus such as a kotatsu, heater,
electric blanket, etc. in the close range, note that keeping IS12S close to
your body may make IS12S hot, causing low-temperature burns.
Caution
Do not use power outlets or wiring apparatus beyond its rating. Also,
exceeding rating, for example, by connecting multiple devices to a
single power strip might cause overheating and fire.
Do not use the product when you have removed the microUSB
connection terminal cover, headset connection terminal cover, HDMI
connection terminal cover, microSD memory card insertion slot cover,
or au IC-Card insertion slot cover. Doing so might allow dust or other
foreign objects to get inside and cause a fault.
Do not place near corrosive chemicals or in places where corrosive
gas is generated. Doing so might cause a fault or loss of internal data.
Do not leave or store with the rear cover removed from IS12S. Doing
so might allow dust or other foreign objects to get inside and cause a
fault.
Do not flick a microSD memory card with your fingernail. The microSD
memory card might jump out, and cause injury or a fault.
Do not use if there is smoke, abnormal odor or noise, excessive
overheating, or other abnormalities. If an abnormality occurs,
disconnect the AC adapter from the power outlet, make sure that the
product is not overheating before turning the power off, and contact
an au shop or Customer Service Center. Also, if you have dropped or
damaged the product, do not continue to use it in that state, and
contact an au shop or Customer Service Center.
When using an AC adapter or external device, insert/remove the
connector straight to/from the terminal. Make sure the orientation of the
connector is correct. Failure to do so might cause damage or a fault.
Obey the following rules for viewing 3D images.
・When viewing 3D images taken with IS12S on the 3D compatible
monitor, be careful not to view for long hours. Doing so might cause
eyestrain, fatigue, feeling ill, etc.
・When viewing 3D images, take a break periodically. Determine how
long or often break is needed by yourself since It varies by
individuals.
・If you feel discomfort, stop viewing 3D images until you recover.
Consult a doctor as required. See also instruction manuals of
devices or software connected to IS12S.
・The vision of young children (especially younger than 6 years old) is
under development. Before young children view 3D images, consult
a pediatrician or ophthalmologist. Adults should supervise young
children to obey above precautions.
Be sure to read the following warnings before
use.
Do not disassemble, modify or directly solder the battery pack. Doing
so might cause spilling of the battery liquid resulting in an accident
such as loss of eyesight if it gets into eyes, or cause overheating, fire
or rupture.
Do not puncture IS12S with a nail, hit it with a hammer or step on it.
Doing so might cause ignition or damage.
Be careful not to have IS12S bitten by your pet. Doing so might cause
leakage, overheating, rupture or ignition of the battery.
Be sure to read the following warnings before
use.
Do not use a cell phone while driving a car or riding a motorbike or
bicycle. Doing so might cause a traffic accident. Use of a cell phone
while driving a car or motorbike is prohibited by law. Use of a cell
phone while riding a bicycle may be punishable by some regulations.
Do not use IS12S while you are aboard an airplane. Use of electric
devices transmitting radio waves in airplane is prohibited by law.
Some airline companies, however, allow their passengers to use cell
phones. For details, contact the airline company you use.
When the microUSB cable connection is made to IS12S microUSB
connection terminal to charge the battery etc., the power is turned on, but
operation is not available. Therefore, microUSB cable connection should
not be made in areas where use is prohibited, such as in airplanes and
hospitals.
Danger
Warning
Turn IS12S off near high-precision electronic devices. The product
sometimes affects electronic equipment. (Examples of electronic
devices that might be affected by the product include cardiac
pacemakers, hearing aids, other electronic medical devices, fire
alarms, and automatic doors. If you are using an electronic medical
device, contact the device manufacturer or retailer for information
about the possible affect of radio waves.）
When using IS12S near an implanted pacemaker, implanted
cardioverter-defibrillator or other electronic medical device, radio
waves might affect these units and devices. So, please observe the
following.
1. Those with an implanted pacemaker or implanted cardioverter-
defibrillator should carry or use IS12S at least 22 cm away from the
implanted pacemaker or implanted cardioverter-defibrillator.
2. Turn IS12S off in crowded trains or other crowded places, since
there may be people with an implanted cardiac pacemaker or
implanted cardioverter-defibrillator nearby.
3. Pay attention to the following points when using the product inside
medical institutions.
・Do not bring IS12S into operating theaters, intensive-care units
(ICU) and coronary care units (CCU).
・Turn IS12S off in hospital wards. If the function to automatically
turn ON the power is set, cancel the setting before turning the
power OFF.
・Even if you are in a lobby, etc., be sure to turn IS12S off when
there are electronic medical devices nearby.
・When a medical institution has laid down designated areas where
use of the product is prohibited or is not allowed to be brought in,
abide by the instructions of that medical institution.
4. When using electronic medical devices other than an implanted
pacemaker and implanted cardioverter-defibrillator outside a
medical institution (e.g. home medical treatment), check
individually with the manufacturer of the electronic medical device
regarding the influence of radio waves.
Stay alert to your surroundings when calling, messaging, shooting
photos, playing games, browsing the Internet, watching TV (1Seg) or
listening to music. Failure to do so might cause a fall or traffic
accident.
■Internal battery
(The internal battery of IS12S is a lithium-ion
battery.)
The internal battery is not fully charged at the time of
purchase. Charge the battery before using the product.
Do not send data by infrared communication with the infrared port
pointing toward eyes. Doing so might affect eyes. Also, sending data
with the infrared port pointing toward some other infrared device
might cause false operation, etc.
Flash/Photo light emits strong light. Do not light the photo light in front
of a person's eyes. Do not gaze at the light emitting part when the
flash/photo light is lighted. Doing so might cause impairment of
eyesight, etc. Be especially careful not to shoot small children from a
very close distance.
Do not light the flash/photo light toward a driver of a car, motorbike or
bicycle. If dazzled by the light, the driver might become unable to
drive and cause an accident.
Sometimes, very rarely some people demonstrate symptoms such as
temporary muscle spasms, loss of consciousness, etc. by receiving
stimulation by strong light or watching repeatedly flickering screens.
Those with a past history of this should consult with a physician
beforehand.
Be sure to read the following cautions before
use.
The Bluetooth®function, wireless LAN (Wi-Fi®) function and FeliCa™
reader/writer function of IS12S conform to domestic wireless
standards in Japan and FCC/IC/CE standards, and have been
certified. Use of the Bluetooth®function, wireless LAN (Wi-Fi®)
function and FeliCa™reader/writer function may be restricted in some
countries/regions. If you are using the wireless LAN function overseas,
check the relevant laws and regulations of the country/region you visit.
Use of the product in a car sometimes affects on-vehicle electronic
devices, though this rarely happens. If this happens, stop use since
this may impair safe travel.
If you feel any abnormality with your skin, immediately consult a
dermatologist. Itching, rashes, eczema, etc. sometimes occurs
depending on your physical constitution and condition. The materials
of parts used on IS12S are as follows.
Caution
Part Material Surface treatment
External case
(Front cover)---Black
PC resin (with
glass)+SUS sheet
metal
Urethane coating
External case
(Front cover)---White, Pink
PC resin (with
glass)+SUS sheet
metal
UV coating
External case
(Rear frame)
PC resin
(with glass)
Non-conductive
vacuum
metallization
(tin)+UV coating
External case
(Back cover)---Black
PC resin
(with glass)
Urethane coating
External case
(Back cover)---White, Pink
PC resin
(with glass)
UV coating
Exterior case
(HDMI connection terminal cover,
Headset connection terminal cover,
microUSB connection terminal cover)
PC resin Non-conductive
vacuum
metallization
(tin)+UV coating
Exterior case
(microSD memory card insertion slot
cover, au IC-Card insertion slot cover)
---Black
PC resin
(with glass)
Non-conductive
vacuum
metallization
(tin)+UV coating
Exterior case
(microSD memory card insertion slot
cover, au IC-Card insertion slot cover)
---White, Pink
PC resin
(with glass)
Non-conductive
vacuum
metallization
(tin)+UV coating
Transparent plate (Camera) PC resin+
PMMA resin
AR treatment
Transparent plate (Flash) PC resin −
Transparent plate (Display) Glass + PET resin Hard coating
Power key, Volume key, Camera key PC resin UV coating
Whip antenna (cover) PC/ABS resin −
Whip antenna (top of shaft) SUS −
Whip antenna (middle of shaft) SUS −
Whip antenna (bottom of shaft) Nickel titanium −
Whip antenna (top of hinge) SUS Tin-cobalt plating
Whip antenna (bottom of hinge) Brass Tin-cobalt plating
Do not bring the product close to or put it into magnetized objects
such as cash cards, floppy disks, credit cards, and prepaid cards.
Doing so might result in loss of recorded information.
Do not swing IS12S around by holding the Stereo Headset with
Microphone (Sample) or hand strap. Doing so might cause injury,
accident, malfunction or damage. Do not use a damaged hand strap.
Do not allow liquids, metal objects, burnable items, and other foreign
matter to get inside the microUSB connection terminal, headset
connection terminal, HDMI connection terminal, microSD memory
card insertion slot and au IC-Card insertion slot. Doing so might cause
fire, electric shock or a fault. Use the product with the covers closed.
If the covers are open, dirt or water may get inside causing a fault.
Stow the whip antenna properly when not watching TV (1Seg). If you
operate the product for calling, etc. with the whip antenna extended, it
might cause unexpected injury by hitting your face, etc.
If you have a weak heart, be careful when setting the incoming
vibration and ringtone volume. They might affect heart.
Pay attention to items becoming stuck to the earpiece, speaker, display.
These parts use magnets, and so thumbtacks and pins, craft knife blades,
staples, and other metal objects sometimes become stuck to the main
unit, and cause unexpected injury. Before using the product, be sure to
check that there are no foreign objects on the earpiece or other parts.
Do not place the product directly on sand at a beach, etc. Sand or
other small particles might get inside the earpiece, microphone or
speaker, causing the volume to drop. If sand gets inside the IS12S
main unit, it might cause overheating or a fault.
When using IS12S for calling, data communication or watching TV
(1Seg), be careful not to keep IS12S in direct contact with your skin
for a prolonged period, or not to cover the product with paper, cloth,
bedding, etc. Doing so might cause fire, burns or a fault.
Do not fold the whip antenna or swing IS12S with the whip antenna extended.
Doing so might cause injury or deform or damage of the whip antenna.
Part Material Surface treatment Do not use ballpoint pens, pencils or other sharp-pointed objects for
touch panel operation. Doing so might cause display damage.
Do not operate the touch panel with fingernails. Doing so might result
in split nails causing injury.
When connecting the Stereo Headset with Microphone (Sample) with
IS12S to play games, music or watch TV(1Seg), adjust the volume to
the proper level. Too loud volume may cause a hearing loss. And, if
you cannot hear the sound around you clearly, it may cause an
accident.
Mishandling is dangerous as it might cause
overheating, leakage or rupture. Be sure to read
the following hazards before use.
If the leaked liquid gets on your skin or clothes, immediately rinse it off
with water to avoid injury. If the liquid gets into your eyes, do not rub
but wash your eyes with water, and immediately consult a doctor to
avoid the risk of losing your eyesight. If the liquid gets on a device,
wipe it off without touching it.
The battery is a consumable item. If the performance of a battery
does not recover (e.g. the usable time after each charge has become
extremely short), the battery is at the end of service life, so stop using
the battery. Failure to do so might cause overheating, ignition, rupture
or leakage. Since the battery is built-in type, IS12S is taken by au
shop etc. and a repair is charged. Also, you cannot use the product in
certain period of time. Note that the length of service life varies
depending on the usage condition, etc.
Danger
■Charging equipment
■au IC-Card
■Stereo Headset with Microphone (Sample)
Mishandling might cause overheating, fire,
electric shock, etc. Be sure to read the following
warnings before use.
Do not use at other voltages than the specified power supply voltage.
Doing so might cause ignition, fire, overheating or electric shock.
AC adapter: 100 VAC to 240 VAC (Connect to the AC outlet for internal
household use)
When charging the product overseas, use AC Adapter for global use.
Firmly insert the AC adapter's power plug into the power outlet down
to the base of its pins. Incomplete insertion of the power plug might
result in electric shock or fire caused by overheating and fire. Do not
use damaged AC adapters or loose power outlets.
Do not damage, modify, twist, pull or place a heavy object on the
microUSB cable of the AC adapter. Do not use a damaged microUSB
cable. Doing so might cause an electric shock, short circuit or fire.
Do not let your hands, fingers and other parts of the body touch the
desktop holder connection terminal or microUSB connection terminal.
Doing so might cause electric shock, injury or a fault.
If you hear thunder, do not touch the power plug. Doing so might
cause an electric shock as a result of a lightning strike.
Before cleaning the charging equipment, unplug AC Adapter plug
from the power outlet. If the plug remains plugged in when you clean
the equipment, it might cause an electric shock or short circuit. Also,
wipe off dust on the AC Adapter plug. Failure to do so might cause
fire, burns or electric shock.
Install and position in-car devices where they do not hinder driving or
safety equipment such as airbags. Failure to do so might cause a
traffic accident. Install in-car devices following the instructions of their
manuals.
Remove the power plug from the outlet when not using the adapter for
an extended period. Failure to do so might cause electric shock, fire
or a fault.
Warning
The AC adapter is not waterproof. Do not use in places subject to
splashing with water, pet urine or other liquids. Doing so might result
in faults resulting from overheating, fire, electric shock, or short-
circuiting of electronic circuits. In the event that the product is
splashed with liquid, immediately disconnect the AC adapter's power
plug.
Mishandling might cause overheating, fire,
electric shock, malfunction, damage, etc. Be
sure to read the following cautions before use.
Do not leave the desktop holder on the floor. Doing so might cause
injury or accident if they accidentally step on the holder or fall.
Do not use in humid places such as bath areas, or connect/
disconnect the AC adapter with wet hands. Doing so might cause
electric shock or a fault.
Charge the battery in a stable place. If placed on an inclined surface
or wobbly stand, the product might fall causing injury or damage. Be
careful especially when vibration is set. In addition, do not cover or
wrap the product with a cloth or bedding. Doing so might cause
removal of IS12S, fire or a fault.
When unplugging the AC adapter power plug from the outlet, hold
and pull the power plug. If you pull the microUSB cable, the microUSB
cable might be damaged.
Do not use the desktop holder in a car. Doing so might disturb driving
and cause an accident. It is presumed that the desktop holder will be
used in the room and stable place.
If you feel any abnormality with your skin, immediately consult a
dermatologist. Itching, rashes, eczema, etc. sometimes occurs
depending on your physical constitution and condition. The materials
of parts used on the Sony Ericsson AC adapter 04 and Desktop
Holder are as follows.
Part Material Surface treatment
[microUSB cable] plug part PBT resin −
[microUSB cable] cable Elastomer resin −
[microUSB cable] noise filter cover PP resin −
[AC adapter] exterior PC resin −
Caution
[AC adapter] plug (Metallic part) Copper alloy Nickel plating
[Desktop Holder] upper case ABS resin −
[Desktop Holder] lower case ABS resin −
[Desktop Holder] inner chassis ABS resin −
[Desktop Holder] lock POM resin −
[Desktop Holder] button POM resin −
[Desktop Holder] safety lever POM resin −
[Desktop Holder] output terminal Phosphor bronze Gold plating
[Desktop Holder] rubber foot Polyurethane resin −
Be sure to read the following warnings before
use.
Do not put the au IC-Card in a cooking apparatus such as a
microwave oven or a pressure vessel. Doing so might cause melting,
overheating, fuming, loss of data or a fault.
Be sure to read the following cautions before
use.
Be careful not to injure your hand or finger when attaching/removing
the au IC-Card.
Use only the devices specified by the Company to insert the au IC-
Card in. Using a device not specified by the Company might cause
loss of data or a fault. For the specified devices, contact an au shop
or Customer Service Center.
Do not disassemble or modify the au IC-Card.
Doing so might cause loss of data or a fault.
Do not use or leave the au IC-Card in hot places such as by the fire or
a heater. Doing so might cause melting, overheating, fuming, loss of
data or a fault.
Part Material Surface treatment
Warning
Caution
Do not throw the au IC-Card into a fire or heat it. Doing so might cause
melting, overheating, fuming, loss of data or a fault.
Do not touch the IC (metal) part of the au IC-Card or short-circuit it.
Doing so might cause loss of data or a fault.
Do not drop the au IC-Card or subject it to strong impact. Doing so
may cause a fault.
Do not fold, bend or place a heavy object on the au IC-Card. Doing so
may cause a fault.
Do not wet the au IC-Card. Doing so may cause a fault.
Do not scratch the IC (metal) part of the au IC-Card. Doing so might
cause a fault.
Do not store the au IC-Card in dusty places. Doing so might cause a
fault.
Do not store the au IC-Card in places exposed to direct sunlight or hot
and humid places. Doing so may cause a fault.
Store the au IC-Card out of reach of small children. Failure to do so
might cause injury, etc. if they accidentally swallow and choke on it.
Be sure to read the following warnings before
use.
Do not use the product to play games, music or watch TV (1Seg)
while driving a car or motorbike, or riding a bicycle or walking. Doing
so might compromise traffic safety and cause an accident.
Warning
1 2 3
4 5 6 7
8 9 10 11
12 13 14 15

These precautions are provided to ensure that performance can be fully
demonstrated. Thoroughly read these precautions to ensure correct use.
■Precautions common to IS12S, internal battery, charging equipment,
au IC-Card, peripheral devices
■IS12S Main unit
Be sure to read the following cautions before
use.
When playing games, music or watching TV (1Seg), adjust the volume to
the proper level. Setting too loud a volume or using the earphone
continuously for a long period of time might adversely affect your ears.
Even when the volume is adjusted moderately, using the earphone for a
long period of time might cause a hearing loss. Also, raising the volume too
high might prevent you from hearing sounds around you, which might in
turn lead to a traffic accident at a railroad crossing or pedestrian crossing.
Do not wrap the cord around IS12S to use. Sensitivity might drop, causing audio
to be interrupted or noise to be heard. Do not pull the cord to remove. Do not hang
the product by holding the cord. Doing so might cause damage the terminal.
Prevent dust from adhering to terminal. Failure to do so might cause a
fault.
Insert/remove the connector straight to/from the terminal of IS12S.
When adjusting the volume with the Stereo Headset with Microphone
(Sample) inserted into the product, raise the volume a little at a time. If
you raise the volume too much from the outset, sudden loud noise
from the earphone, etc. might adversely affect your ears.
For detailed operations on the initial setup, refer to the instruction
manual for the Stereo Headset with Microphone (Sample).
If you feel any abnormality with your skin, immediately consult a
dermatologist. Itching, rashes, eczema, etc. sometimes occurs
depending on your physical constitution and condition.
The materials of parts used on the Stereo Headset with Microphone
(Sample) are as follows.
Part Material Surface treatment
Exterior of earphone, exterior of
microphone with switch
PC +ABS resin −
Earpieces (S/M/L) Silicon rubber −
Cable Elastomer resin −
Connection plug (3.5 mm) (Body) Polyurethane resin −
Connection plug (3.5 mm) (Metallic part) Copper alloy Gold plating
Caution
Handling precautions
●IS12S is waterproof, however, do not allow water to seep into the product
and do not allow accessories or optional devices to get wet. The supplied
and optional accessories are not waterproof.
●Do not apply excessive force to IS12S during use. Be sure not to put the
product into a tightly packed bag or place a heavy object on the product in
a bag. Sitting on the product in your pocket might damage the display or
internal circuit board resulting in a malfunction.
Keeping an external device connected to the microUSB connection
terminal, headset connection terminal, or HDMI connection terminal might
damage the connector resulting in a malfunction. Such damage and
malfunction are not covered by the warranty, even if there is no external
damage.
●IS12S has a waterproof property equivalent to IPX5 (former JIS IP5) and
IPX7 (former JIS IP7) on the condition that the microUSB connection
terminal cover, headset connection terminal cover, HDMI connection
terminal cover, microSD memory card insertion slot cover and au IC-Card
insertion slot cover are securely closed. However it does not mean perfect
waterproof. Do not attach/remove a microSD memory card or au IC-Card or
open/close the microUSB connection terminal cover, headset connection
terminal cover or HDMI connection terminal cover in the rain or with
waterdrops on the surface of the product. Doing so might cause water
intrusion resulting in internal corrosion. The supplied and optional
accessories are not waterproof. Malfunctions determined to be caused by
water soak are not covered by the warranty.
●Do not use the product in extremely hot, cold or humid conditions. (Use
within an ambient temperature range of 5℃to 35 ℃and humidity range of
35% to 85%.)
●Do not use in places subject to lots of dust or vibration. Doing so might
cause a fault.
●Clean the desktop holder connection terminal, microUSB connection terminal,
headset connection terminal, and HDMI connection terminal with dry cotton
swabs, etc. every now and then. Soiled terminals might cause poor connection.
Do not exert a strong force to clean microUSB connection terminal, headset
connection terminal or HDMI connection terminal to prevent deformation.
●Clean the product with a soft dry cloth (such as the type used for
eyeglasses). Forceful rubbing with a dry cloth may scratch the display. The
display may be stained if splash or smear is left attached to the surface.
Wiping the product using alcohol, thinner, benzine, detergent, etc. might
erase the printing on the outer casing or cause discoloration.
●Use as far away as possible from land-line phones, TVs and radios. Use
nearby might affect them.
●IS12S may become warm while talking on a call, watching TV(1Seg),
charging or during other operations, depending on the situation, but this is
not abnormal.
●When the product is used by children, parents or guardians should
thoroughly read "Instruction Manual" and teach the children how to use it.
●If IS12S becomes high temperature, the display may become dim. This is
normal.
●Do not forcefully press, tap or intentionally subject the display to strong
impact. Doing so might cause scratching or damage.
●Do not forcefully press your fingernails or hard objects against display or
keys surface. Doing so might cause scratching or damage.
●Information on certification and conformity mark specified for the product (with
certification number) can be confirmed with the following operations.
From the Home screen, tX[Settings]X[About phone]X[Legal information]
X[Cetificates]
This product has acquired the certification of conformity with technical
regulations for the specified radio station based on the Radio Law, and the
"Technical Conformity Mark " can be confirmed in the product as a certificate.
Confirm contents of electrical certificates in the product for information on
certification.
If the screws of the product are removed and modifications are made to the
internal components, the certification of conformity with technical regulations will
become invalid. Never use the product without the valid certification. Doing so
violates the Radio Law.
●To prevent unlawful modification, IS12S has been designed so that it cannot be
easily disassembled. Modifying the product is prohibited by the Radio Law.
●Contents saved in IS12S, such as contacts, Gallery, might be altered or lost
by an accident, fault, repair or mishandling. Be sure to keep a copy of
important contents. Note that the Company assume no responsibility for
any damages or lost profits resulting from altered or lost contents.
●Note that mails and downloaded data (both charged or free content) saved
on IS12S cannot be returned to the customer when the product is replaced
for repair of a fault, for example.
●IS12S uses liquid crystal for its display. The display response speed may
become slow when the ambient temperature is low, which is due to the
property of liquid crystal and not a malfunction. The display response
speed will return to normal at room temperature.
●Although the display used on IS12S is made using high-precision technology,
some pixels (dots) might be lit or out at all times. This is not a malfunction.
●Take care not to inconvenience people around you when you use the
product in a public place.
●You are recommended to store copies of individual data such as photos
you took, videos and music in a PC by sending each file as mail
attachment, etc. Note, however, that you may not be able to make copies of
some copyrighted data even by the above-mentioned means.
■Touch Panel
■Internal battery
■Charging equipment
■au IC-Card
●Take care not to place magnetized items such as magnetic cards,
speakers and TV sets near IS12S, as it might cause malfunction. Putting
strong magnetism close to the product might cause false operation.
●When you put the product in your pocket or bag, take care so that the
display does not come in contact with metal objects or other hard objects,
as it might cause scratching or damage. Also, be careful not to scratch or
damage the display by using a strap whose metal or other hard part comes
in contact with the display.
●When suddenly brought into a warm place from a cold place, or when in a
humid location, or when used where temperature suddenly changes (e.g.
near the air discharge port of an air conditioner), water droplets (i.e.
condensation) sometimes are formed inside the product. Note that when
used under conditions such as this, humidity might cause corrosion or a fault.
●When wiping the display, wipe with a soft, dry cloth. Use of a glass cleaner
or other similar liquid might cause a fault.
●When connecting the external device with the microUSB connection terminal,
headset connection terminal or HDMI connection terminal, insert/remove the
external device connector straight to/from the microUSB connection terminal,
headset connection terminal or HDMI connection terminal. Failure to do so
might cause damage or a fault.
●Note that applying excessive force with the external device connected to
the microUSB connection terminal, headset connection terminal or HDMI
connection terminal might cause damage.
● Do not discard the product together with regular trash. Please cooperate in the
collection of IS12S when it is no longer needed to protect the environment and
effectively use resources. Old products are collected at au shops and other places.
●Insert only a microSD memory card into the microSD memory card insertion
slot on IS12S.
●Do not exert excessive force when attaching/removing a microSD memory
card. Doing so might injure your hands or fingers.
●While writing/reading data, do not subject the product to vibration or
impact, remove a microSD memory card, turn off the power or restart.
Doing so might cause loss of data or a fault.
●When hearing the other party's voice, make sure that the earpiece is
placed at the center of your ear. If the earpiece (audio output port) is
closed by the ear lobe, it may be hard to hear the voice.
●Even if you cover the microphone to make your voice inaudible to the other
party, the other party can hear your voice.
●When using handsfree call, take care to keep the speaker at a safe
distance from your ears, as the speaker volume may be too loud.
●Do not cover the light sensor with your finger or put a sticker on it. Doing so
might hinder the light sensor from detecting the ambient brightness and
functioning correctly.
●Do not put a sticker, etc. on the proximity sensor. Doing so may cause the
sensor to malfunction and make the display always turned off while
receiving a call or during a call.
●Do not apply excessive force to the product during use. Note that applying
excessive force to IS12S such as swinging or carving the product body
cause malfunction or damage.
●Do not forcefully pull microUSB connection terminal cover, headset
connection terminal cover, HDMI connection terminal cover, microSD
memory card insertion slot cover or au IC-Card slot insertion cover might
cause damage.
●While watching TV (1Seg), IS12S becomes hot. Be careful when touching
the product with your hands or face.
●Note that when the shooting screen is displayed continuously for a long
time for still image shooting, video shooting, or TV (1Seg) watching, parts
of the IS12S main unit may get warm, and that contact by your skin with
these parts for a long time might cause low-temperature burns.
●Do not use the product while driving a car, etc. Using functions such as
mail and camera other than talking on the phone with a handsfree kit might
cause a traffic accident and is prohibited by law.
●Use your finger to operate the touch panel. Do not use ballpoint pens,
pencils or other sharp-pointed objects. Using such objects does not only
hinder correct operation of the touch panel, but also might cause
scratching or damage to the display.
●Do not put stickers or sheets (e.g. commercially available protective
sheets, peep prevention sheets) on the display. Doing so might hinder
correct operation of the touch panel.
●Do not operate the touch panel with fingernails. Doing so might result in
split nails or jammed fingers.
●If the display surface is dirty or wet with sweat or water, it may not function
correctly. In such case, wipe the display surface with a dry, soft cloth.
● Note that pressing the touch panel forcefully may cause malfunction or damage.
●When carrying the product in your pocket or bag, take care not to put the
touch panel close to metals or other conductive materials, as it might cause
false operation of the touch panel.
●Use in very hot or cold environments, for example, when left in an
automobile with the windows closed in summer, will cause the internal
battery capacity to drop and shorten the available battery usage time. This
will also shorten the internal battery's service life. Try to use the product as
far as possible at room temperature.
●The internal battery gradually discharges after charging even if IS12S is not
used. The internal battery may discharge completely after long time no
use. Charge before using.
●Because the internal battery performance or service life will become low,
do not store the product in the following conditions.
・Battery level is full (soon after charging is complete)
・Battery level is empty (to the extent that the product is not powered on)
・In extremely hot or humid conditions
●Charge the battery before using the product for the first time after
purchase, or if you have not used the product for a long time.
●The battery is a consumable item. If the performance of a battery does not
recover (e.g. the usable time after each charge has become extremely
short), the battery is at the end of service life, so stop using the battery.
Failure to do so might cause overheating, ignition, rupture or leakage.
Since the battery is built-in type, IS12S is taken by au shop etc. and a
repair is charged. Also, you cannot use the product in certain period of
time. Note that the length of service life varies depending on the usage
condition, etc.
●Do not discard the battery with regular trash. Please cooperate in the
collection of the battery when it is no longer needed to protect the
environment and effectively use resources. au shops and other retailers
collect used battery.
●The internal battery sometimes swell up as they approach the end of their
service life. This is due to the properties of lithium-ion batteries, and is not a
problem in terms of safety.
●When not using the AC adapter, remove the AC adapter's power plug from
the power outlet.
●Do not wrap the microUSB cable inserted into the AC adapter around the
adapter plug or desktop holder. Failure to do so might cause electric
shock, ignition or fire.
●Do not forcibly bend the charging equipment's plug or the connection
between the connector and microUSB cable. Doing so might cause
electric shock, overheating or fire.
●The au IC-Card is lent to you by au. In case of loss or damage, the card will
be replaced at your expense. When malfunction is suspected, or in case of
theft or loss, contact an au shop or PiPit.
●Do not forcibly remove or insert the au IC-Card. Be careful not to exert
excessive force when inserting the card into your au cell phone.
●You are responsible for any damage caused by inserting your au IC-Card
into some other IC card reader/writer, etc.
■Camera
■Music, TV (1Seg) and radio
■Copyrights and rights of portrait
■microSD memory card
●The au IC-Card may become warm during use, but this is not a malfunction
and you can continue to use the card.
●Keep the IC (metal) part of your au IC-Card clean. Clean the product with a
soft dry cloth (such as the type used for eyeglasses).
●Do not put stickers, etc. on the au IC-Card.
●Do not insert a card other than au IC-Card into IS12S. You cannot use
IS12S with a card other than au IC-Card.
●Do not insert a micro au IC-Card with a conversion adapter. Doing so might
cause a fault.
● When using the camera, follow common rules of etiquette regarding camera use.
●Image data might be altered or lost due to malfunction, repair or
mishandling of IS12S. The Company takes no responsibility for recovery of
altered or lost data, damages resulting from altered or lost data, and lost
profits.
●When photographing important occasions (such as a wedding), take a trial
shot and check the shot image to make sure it is correctly shot and the
audible sound is recorded.
●Be careful of shooting and publishing other individuals indiscreetly, as it
might infringe on their portrait rights, etc.
●Images shot with the camera may not be used or transferred without the
consent of the copyright holder (photographer) except for personal use or
other purposes explicitly permitted by law. Note that shooting itself may be
restricted at some live performances, shows and exhibitions even for
personal use.
●Do not record information at places where taking a photo is prohibited or
bookstores using IS12S camera feature.
●Do not leave the camera lens exposed to direct sunlight. Imaging elements
might be discolored or burnt.
●Do not listen to music or watch videos while driving a car or motorbike, or
riding a bicycle. Use of cell phones while driving a car or motorbike is
prohibited by law. (Use of cell phones while riding a bicycle may also be
punishable by law.) In addition, stay alert to the traffic around you even
when walking. Surrounding sounds may not be heard clearly, and gazing at
the screen might distract your attention causing a traffic accident. Be
especially careful at railroad crossings and pedestrian crossings.
●Take care not to listen at ear-splitting volume for a long time, as it might
affect hearing.
●Be careful of sound leakage from the Stereo Headset with Microphone
(Sample) in trains or other places with many people around you.
●You are not allowed to copy, modify or edit the data you shot or recorded
using IS12S without consent of the copyright holder, except for personal
use, under the copyright law. In addition, do not use or modify portraits or
names of other individuals without their consent, as it might infringe on
rights of portrait. Note that shooting and recording may be restricted at
some live performances, shows and exhibitions even for personal use.
●Be careful about the copyright and portrait right when posting photos you
shot, etc. on Internet homepages.
●The transfer of images, music, etc. covered by copyright is not allowed
excluding instances laid down separately by the Copyright Act.
●This product is licensed based on MPEG-4 and AVC patent portfolio
license with MPEG LA. LLC. The use is allowed for personal and nonprofit
use only in the cases below.
・Recording videos that conform to MPEG-4 and AVC Visual Standard
(hereinafter referred to as MPEG-4 and AVC Video)
・Playing MPEG-4 and AVC Videos recorded personally by consumers not
engaged in profit activities
・Playing MPEG-4 and AVC Video supplied from the provider licensed from
MPEG-LA, LLC. For further utilizing, please contact MPEG LA, LLC in
U.S. (http://www.mpegla.com)
●Using a microSD memory card not specified by the Company might cause
loss of data or a fault. For the specified microSD memory card, contact an
au shop or Customer Service Center.
●When a microSD memory card is not inserted into IS12S, you cannot
operate for a microSD memory card.
●Insert a microSD memory card correctly. If not inserted correctly, you
cannot use a microSD memory card.
●Do not allow a microSD memory card contact side to touch metals, wet
water or get dirt.
●Do not bend, fold or place a heavy object on or give a strong impact to a
microSD memory card.
●Formatting a microSD memory card may be required. Format it with IS12S
before use.
●After you have used the product for a long time, the microSD memory card
removed may become warm, but this is not malfunction.
●Avoid using and storing the product at a place where static electricity or
electrostatic noise is readily generated.
●When carrying or storing a microSD memory card, put it in a storage case
to avoid impact.
●Do not disassemble or modify.
●Do not put stickers, etc. on a microSD memory card.
●You are recommended to copy data saved in a microSD memory card to
another microSD memory card or a PC for backup.
●When discarding your microSD memory card, you are recommended not
only to delete saved data, but also to destroy the card physically to prevent
the data from being leaked. Control contents saved in your microSD
memory card on your judgement and responsibility.
●When the battery level is low on IS12S, power may be turned off during
saving data in a microSD memory card, so data cannot be saved normally.
That may cause data loss or malfunction. You are recommended to save
data when the battery is charged enough.
Backup content on IS12S
●Please back up important content recorded or downloaded to IS12S to an
outside source*1.
Content recorded to memory on IS12S sometimes disappears or is
altered by unexpected factors, such as static electricity or a fault, repair,
mishandling, etc.
*1 How to make backups:
・Store important data such as phonebook data, music, shot photos and
videos on microSD memory cards. You can also send files as mail
attachment or transfer to your PC. Note, however, that there are some
data that cannot be copied by using these means.
■Notice
・Reproduction of the content of "Instruction Manual" in part or in whole is
prohibited.
・The content of "Instruction Manual" is subject to change without notice.
・Every effort has been made in the preparation of "Instruction Manual".
Should you notice any unclear points, omissions, etc., feel free to
contact us.
・Wrong page order or missing pages will be replaced.
IS12S has a waterproof property equivalent to IPX5 (former JIS IP5)
*1
and IPX7
(former JIS IP7)
*2
on the condition that microUSB connection terminal cover,
headset connection terminal cover, HDMI connection terminal cover, microSD
memory card insertion slot cover and au IC-Card insertion slot cover are
securely closed (based on in-house testing). Specifically, you can make calls
holding the product with wet hands in the rain (less than 20 mm per hour) without
umbrella, as well as use the product in a place with water such as a bathroom or
kitchen. Before using the product, thoroughly read "Important items to remember
before use" and "Tips for comfortable use" to ensure correct use. Failure to follow
the contents described in these sections may cause intrusion of water, sand or
other foreign material, resulting in overheating, ignition, electric shock, injury or a
fault.
*1 IPX5 equivalent means that the product will maintain its operability as a
phone even if it is sprayed with water from a 6.3 mm diameter nozzle at a
distance of about 3 meters for more than 3 minutes at a rate of about 12.5
liters per minute from any direction.
*2 IPX7 equivalent means that the product will maintain its operability as a
phone with no water getting inside the IS12S main unit even if it is gently
submerged in a tank of still tap water at room temperature to a depth of 1
meter for about 30 minutes.
Since operation of the product on each usage scene was confirmed based on
the above assumption, proper operation of the product in every possible
condition during actual use is not guaranteed. Malfunctions determined to be
caused by mishandling by the customer are not covered by the warranty.
aClose firmly the microUSB connection terminal cover, headset connection
terminal cover, HDMI connection terminal cover, microSD
memory card
insertion slot cover and au IC-Card insertion slot cover.
・Waterproofness is only effective when the covers are securely closed.
・Just a small particle (a hair, etc.) between contact surfaces can cause
water leak.
・Do not open/close the microUSB connection terminal cover, headset
connection terminal cover, HDMI connection terminal cover, microSD
memory card insertion slot cover or au IC-Card insertion slot cover if the
main unit or your hands are wet.
・When closing each cover, after stowing the cover hinge, press the entire
cover with the flat part of your finger. Then, trace the cover to ensure that
the cover is not partially open.
bDo not immerse the product in water with
soap, detergent or bath salts in it.
cDo not immerse the product in seawater, a
swimming pool or hot spring.
dDo not immerse the product in any liquid
(alcohol, juices, etc.) other than fresh water
and tap water of room-temperature (5-35℃).
eDo not place the product directly on sand at a
beach, etc. Grains of sand or other small
particles might get into the earpiece,
microphone or speaker, causing the volume to
drop. And if sand gets inside the product's
main unit, it might cause overheating or a
fault.
fDo not use the product underwater.
gDo not leave the product in a humid place such as a bathroom or kitchen for
an extended period of time.
･Once the product gets wet, water may remain in gaps of the main unit. Shake
the product well to drain water. Especially make sure to drain water remaining
in the back side, power key, volume key and camera key parts. (If you carry
the product with water remaining in it, your clothes, bag or contents of the bag
may get wet. Also, using the product while it is wet may cause the volume to
drop.)
･Even after water is drained, the inner parts are still wet. Although you can use
the product, do not place it near things that must not get wet. Take care not
to wet your clothes, bag or contents of the bag.
･Drain water if it becomes temporarily hard to hear the sound due to water
remaining in the microphone or earpiece.
■Notes on various usage scenes
In the rain: You can make calls holding the product with wet hands in the rain
without umbrella.
･The rain in this case means a moderately-heavy rain (less than 20 mm per
hour).
Water drops on the display might cause errors in the touch panel operation.
･Never open/close the microUSB connection terminal cover, headset
connection terminal cover, HDMI connection terminal cover, microSD
memory card insertion slot cover or au IC-Card insertion slot cover if IS12S is
exposed to rain, the waterdrop is attached on the product, or your hands are
wet.
In the shower: You can make calls holding the product with wet hands while
taking a shower.
･Water drops on the display might cause errors in the touch panel operation.
･Avoid spraying the product with high-pressure water, as the product is not
designed to withstand high water pressure.
Washing: You can wash the product under a mild flow (less than 6 liters per
minute) of tap water at room temperature (5℃to 35℃) at a distance of about
10 cm from the faucet or showerhead.
･Do not spray the product with high-pressure water or submerge it in water for
extended periods of time, as the product is not designed to withstand high
water pressure.
･Wash the product with your hands holding the microUSB connection terminal
cover, headset connection terminal cover, HDMI connection terminal cover,
microSD memory card insertion slot cover and au IC-Card insertion slot cover
so that they do not open. Do not use a brush or sponge.
･Do not wash the product in a washing machine or ultrasound bath.
･Do not splash the product with or immerse it in soap water, detergent water,
etc. other than tap water.
In the bath: You can use the product in a bathroom. Although you can make calls
with wet hands, do not immerse the product into a bathtub. The product is not
resistant to high temperatures.
･Do not use the product in a bathroom for an extended period of time. The
product is not moistureproof.
･Do not immerse the product in hot spring water, soap water, detergent water,
or water with bath salts in it. Also, do not use IS12S underwater. Doing so may
cause a fault.
･You may experience poor signal reception depending on the position of the
bathroom.
･Extreme changes in temperature cause condensation. Wait until the IS12S
main unit reaches room temperature before you bring IS12S from a cold place
into a warm bathroom.
･If condensation occurs inside the display, leave the product at room
temperature for a while until condensation is cleared.
･When viewing 1Seg, place the product on a stable surface.
･Do not splash the product with hot water. The product is not resistant to high
temperatures.
･Do not bring the desktop holder into a bathroom.
･Use within an ambient temperature range of 5℃to 40 ℃(only temporary use
at bathroom etc. in the range of 36℃to 40℃) and humidity range of 35% to
90% (only temporary use at bathroom etc. in the range of 86% to 90%).
In the kitchen: You can use the product in the kitchen and other places where
water is used.
･Do not sprash the product with or immerse it in soap water, detergent water,
seasonings, juices, etc. other than tap water.
･Do not immerse the product in or splash it with boiling water. The product is
not resistant to high temperatures.
･Do not place the product where it gets extremely hot or cold such as near a
stove or in a refrigerator.
･When viewing 1Seg, place the product on a stable surface.
On the poolside
･When viewing 1Seg, place the product on a stable surface.
･Do not immerse the product in or splash it with pool water.
･Do not use the product underwater. Doing so may cause a fault.
･When the product gets pool water, wash the product under a mild flow (less
than 6 liters per minute) of tap water at room temperature (5℃to 35 ℃).
･Wash the product with your hands holding the microUSB connection terminal
cover, headset connection terminal cover, HDMI connection terminal cover,
microSD memory card insertion slot cover and au IC-Card insertion slot cover
so that they do not open. Do not use a brush or sponge.
Notes on waterproofness
Important items to remember before use
Tips for comfortable use
Soap/detergent/
bath salts
Seawater
Hot spring Sand/dirt
16 17 18 19
20 21 22 23
24 25 26 27
28 29 30 31

■Common precautions
･microUSB connection terminal cover, headset connection terminal
cover, HDMI connection terminal cover, microSD memory card insertion
slot cover and au IC-Card insertion slot cover
Make sure that the microUSB connection terminal cover, headset connection
terminal cover, HDMI connection terminal cover, microSD memory card
insertion slot cover and au IC-Card insertion slot cover are tightly closed. Just
a small particle (a hair, etc.) between contact surfaces can cause water leak.
Do not open/close the microUSB connection terminal cover, headset
connection terminal cover, HDMI connection terminal cover, microSD
memory card insertion slot cover or au IC-Card insertion slot cover with
gloved hands. Just a small particle (a hair, etc.) between contact surfaces
can cause water leaks. Wipe off any minuscule droplets of water or dirt with
a clean dry cloth before closing the covers. If the microUSB connection
terminal cover, headset connection terminal cover, HDMI connection terminal
cover, microSD memory card insertion slot cover or au IC-Card insertion slot
cover is deteriorated or damaged, the waterproof property becomes
ineffective. In such case, contact an au shop near you or Customer Service
Center.
･If seawater or detergent gets on the product
If any liquid other than plain water (e.g. seawater, alcohol, juices) gets on the
product, immediately rinse it with plain water. You can wash the product under
a mild flow (less than 6 liters per minute) of tap water at room temperature
(5℃to 35 ℃) at a distance of about 10 cm from the faucet or showerhead. If
the product gets dirty, wash it with your hands holding the microUSB
connection terminal cover, headset connection terminal cover, HDMI
connection terminal cover, microSD memory card insertion slot cover and au
IC-Card insertion slot cover so that they do not open. Do not use a brush or
sponge.
･After the product gets wet
After the product gets wet, drain water, and wipe the main unit. In cold
climates, water on the main unit may turn to frost. Using the product with frost
may cause a fault. Do not leave the product without wiping off water. (No
special measures against condensation have been implemented in this
product.) Do not leave IS12S without wiping off water. Water may get in the
back side, Power key, Volume key or Camera key. If that happens, remove the
water by shaking IS12S. (Check your surroundings and be carful not to drop
IS12S.) Wipe off the remaining water quickly with a clean dry cloth. Note that
your clothes or bag may get wet by water that is not removed or collects in
the gap. Also, do not leave water droplets in the earpiece, microphone or
speaker. That may interfere with talking.
･Charging
Never charge the battery if the product is wet. The supplied and optional
accessories are not waterproof.
･Waterproof property
Do not use the product in places where it may be sprayed with high-pressure
water (e.g. near a faucet or showerhead) or submerge it in water for extended
periods of time, as the product is not designed to withstand high water
pressure. Also, do not expose the product to a water flow stronger than the
specified flow rate (i.e. 6 liters per minute from a faucet or showerhead, at
which you might even feel pain in the skin). Doing so might cause a fault, even
though IS12S has a waterproof property equivalent to IPX5 (former JIS IP5).
Do not wash the product in a washing machine or ultrasound bath. IS12S
does not float on water.
･Heat resistance
Do not use the product in places where boiling water may splash on it, in
saunas or near hot air (e.g. hairdryer). IS12S is not resistant to high
temperatures.
･Shock
IS12S is not resistant to shock. Do not drop the product or subject it to shock.
Also, do not jab the earpiece, microphone or speaker with a cotton swab or
any sharp object. Doing so might damage or deform the main unit causing
water leak.
■Draining water after wetting the product
As some parts of IS12S are not waterproof, if you use the product after it gets
wet, water remaining in those parts might wet your clothes or bag, or the sound
might become hard to hear. Follow the steps below to drain water.
aWipe off water on the product with dry towel, cloth, etc.
bHold IS12S firmly and shake it approximately 20 times as shown.
* When shaking IS12S, check the safety around you and hold it firmly
enough not to drop it.
cIf water flows out from inside of IS12S, wipe it off with a dry cloth etc.
* Water left on earpiece, microphone or speaker is not easily wiped off.
Face the product downward and push it on a cloth to wipe off the water.
dPlace a dry towel or cloth under the product and leave them for a couple of
hours at room-temperature to dry.
* If the product is not dried enough, you cannot hear the sound easily.
Leave the product enough time to dry before use.
■Charging
The supplied and optional accessories are not waterproof. Check the following
before and after charging.
･Never charge the battery if the IS12S main unit is wet. Doing so might cause
electric shock or short circuit resulting in a fire or fault.
･Check whether IS12S is wet. When charging the battery when or after the
product is wet, adequately drain it and wipe off water with a dry, clean cloth
etc., before connecting the desktop holder or opening the microUSB terminal
cover.
･When the microUSB terminal cover is opened for charging, close the cover
firmly after charging. It is recommended to use the desktop holder for
charging to prevent water from seeping inside from the microUSB terminal
cover.
･Do not touch the AC adapter or desktop holder with wet hands. Doing so
might cause electric shock.
･Use the AC adapter or desktop holder away from water. Do not use them in a
bathroom, shower room, kitchen, lavatory or other highly humid area. Doing
so might cause fire, electric shock or a fault. And, do not carry them into a
bathroom etc., even when not charging. Doing so might cause a fire or
electric shock.
Bluetooth®and wireless LAN functions of this product use frequencies in the
2.4 GHz band ranging from 2,400MHz to 2,483.5MHz.
TYPE:AAH-5880016-BVFCCID:PY7A5880016IS12S
a
b
c
Notes on using Bluetooth®/wireless LAN
functions
Frequency band
2.4 : Indicates radio equipment using 2,400MHz.
FH/XX/DS/OF : Indicates that FH-SS, other scheme,
DS-SS and OFDM are used the
modulation scheme.
1：Indicates that the possible interference distance is about 10 m or less.
4：Indicates that the possible interference distance is about 40 m or less.
8：Indicates that the possible interference distance is about 80 m or less.
For use in airplane, check with the airline company in advance.
･The Bluetooth®function of IS12S conforms to domestic wireless standards in
Japan and FCC/IC/CE standards, and has been certified. Use of the
Bluetooth®function may be restricted in some countries/regions. If you are
using the wireless LAN function overseas, check the relevant laws and
regulations of the country/region you visit.
･The 2.4 GHz band used by wireless LAN (Wi-Fi®) and Bluetooth®devices is shared
by various other devices. For this reason, Bluetooth®device use technologies for
minimizing effects from other devices using the same radio frequency band. In
some cases, however, the communication speed and connectable range may be
decreased, or disconnection may occur, due to interference by other devices.
･The communication speed and connectable range vary depending on the
distance between communication devices, obstacles and the Bluetooth®
devices used.
■Bluetooth®precautions
The frequencies used by the Bluetooth®function of IS12S are in the 2.4 GHz
band. In this frequency band, other similar wireless stations, in-plant wireless
stations for mobile unit identification that require a license for use, such as factory
production lines, specific small power wireless stations that do not require
licenses, amateur wireless stations (collectively called "other wireless stations"
from here on) are operated in addition to home electrical appliances such as
microwave ovens, devices for industrial, scientific and medical devices.
1. Before using IS12S, make sure that "other wireless stations" are not in
operation nearby.
2. In the event that instances of radio wave interference have occurred between
IS12S and "other wireless stations", immediately either relocate IS12S or stop
operation of the device (stop emission of radio waves).
3. If you are unclear on any points or are troubled by anything, contact an au
shop or Customer Service Center.
･The wireless LAN (Wi-Fi®) function of IS12S conforms to the domestic
standards of Japan and FCC/IC/CE standards, and has been certified. Use
of the wireless LAN (Wi-Fi®) function may be restricted in some countries/
regions. If you are using the wireless LAN function overseas, check the
relevant laws and regulations of the country/region you visit.
･Do not use this product in places where electromagnetic waves are
generated or near electric products, AV and OA equipment, or other
magnetized devices.
･Subjecting this product to magnetic or electrical noise might increase noise
and prevent it from performing communications. (This product is particularly
susceptible to noise when it used near a microwave oven.)
･Using this product near a TV, radio or similar appliance might cause reception
interference and disrupt TV images.
･Searching might not be successful if there are multiple wireless LAN (Wi-Fi®)
access points near to the product or the same channel is being used.
･The wireless LAN function cannot be used in airplane. Be sure to turn off the
power even in a wireless LAN (Wi-Fi®) compliant airplane. Some airline
companies, however, allow their passengers to use cell phones. For details,
contact the airline company you use.
■Wireless LAN (Wi-Fi®) precautions
The frequencies used by the wireless LAN (Wi-Fi®) function of IS12S are in the
2.4 GHz band. The frequencies used by the wireless LAN function of this
product are in the 2.4 GHz band. In this frequency band, other similar wireless
stations, in-plant wireless stations for mobile unit identification that require a
license for use, such as factory production lines, specific small power wireless
stations that do not require licenses, amateur wireless stations (collectively
called "other wireless stations" from here on) are operated in addition to home
electrical appliances such as microwave ovens, devices for industrial,
scientific and medical devices.
1. Before using IS12S, make sure that "other wireless stations" are not in
operation nearby.
2. In the event that instances of radio wave interference have occurred between
IS12S and "other wireless stations", immediately either relocate IS12S or stop
operation of the device (stop emission of radio waves).
3. If you are unclear on any points or are troubled by anything, contact an au
shop or Customer Service Center.
◎The Company is not liable for any damages arising from earthquakes,
lightning, storms, floods or other natural disasters, as well as fires, actions by
third parties, other accidents, intentional or mistaken misoperation by the
customer, or use under other unusual conditions outside the responsibility of
the Company.
◎The Company is not liable for any incidental damages (change/
disappearance of described content, loss of business income, disruption of
business, etc.) arising from use of or inability to use the product. It is
recommended that you take a copy of important phone numbers etc.
◎The Company is not liable for any damages arising from failure to observe
the described content of the "Instruction Manual".
◎The Company is not liable for any damages arising, for example, from
malfunction caused by combination with connected devices or software not
related to the Company.
◎Data, etc. registered on the product or microSD memory card is sometimes
altered or lost due to accident or faults, repair or other handling of the
product. The Company is not liable for any damages arising from recovery of
this data or lost income.
◎It is recommended that you store important data in your PC's hard disk, etc.
Note that the company assumes no responsibility whatsoever for alteration
or loss of saved information regardless of cause of malfunction or damage.
* "The Company" as appears on the product refers to the following companies:
Sold by: KDDI CORPORATION, OKINAWA CELLLAR TELEPHONE COMPANY
Manufactured by: Sony Ericsson Mobile Communications Japan, Inc
◎Since constant Internet connection is possible with IS12S, packet
communication may be performed automatically by some applications,
resulting in high packet communication charges. Therefore, subscription to
a packet flat-rate service is recommended.
◎To browse homepages, download applications, communicate using
applications, send/receive mails and configure various settings, connection
to the Internet is required, to which packet communication charge applies.
(Receiving email from au such as "auからの重要なお知らせメール
(important note from au)", "WEB de 請求書お知らせメール (WEB de Seikyu
invoice)" Even if you subscribe Plan E Simple/Plan E, sending and receiving
(〜@ezweb.ne.jp) is not free of charge, packet communication charges
apply. (You need to subscribe to IS NET to use "E-mail (〜@ezweb.ne.jp)".)
* Packet communication charge does not apply to wireless LAN (Wi-Fi®).
：This means that all bandwidths between 2,400MHz to 2,483.5MHz
can be used, and that bands of mobile unit identification devices
can be avoided.
Precautions about Bluetooth®
Precautions about wireless LAN
◎Connections between IS12S and all other Bluetooth®and wireless LAN
(Wi-Fi®) devices have not been confirmed. Therefore, connections with all
Bluetooth®and wireless LAN (Wi-Fi®) devices are not guaranteed.
◎This product supports security features for wireless communications that are
compliant with the Bluetooth®and wireless LAN (Wi-Fi®) standard
specifications, but the security may not be sufficient depending on the usage
environment and configuration. Be carful when making data communication
using the Bluetooth®or wireless LAN (Wi-Fi®) function.
◎Wireless LAN (Wi-Fi®) has the advantage that it can be freely connected
anywhere within the radio wave range, as it uses radio waves for
exchanging information. At the same time, there is a risk that a malicious
third party may obtain unauthorized access if security settings have not
been configured. You are recommended to configure security settings
before using wireless LAN at your discretion and responsibility.
◎The Company assumes no responsibility for leakage of data or information
that may occur during Bluetooth®/wireless LAN (Wi-Fi®) communication.
◎Since Bluetooth®and wireless LAN (Wi-Fi®) functions use the same
frequency band, using the both functions at the same may cause radio
wave interference resulting in decreased communication speed or
disconnection from the network. If connection fails, stop using either of the
Bluetooth®and wireless LAN (Wi-Fi®) functions.
Exemptions
Notes on packet communication charge
◎Be sure to check the security of the application, then install it at your own risk.
Some applications might cause virus infection, damage various data, and
send out your location information, usage history or personal information
stored in your cell phone via the Internet.
◎The Company assumes no responsibility for any failures that might be
caused by applications you have installed. Repair costs in this case may be
charged even during the warranty period.
◎The Company assumes no responsibility for any disadvantage brought to
you or any third party by applications you have installed.
◎Insertion of a microSD memory card is necessary to use some applications.
◎Some applications prohibit the product from entering sleep mode while they
are active, or rapidly drain the battery while running in the background.
◎Operation procedures and screen appearances of the applications
preinstalled in IS12S and those installed by you are subject to change
without notice as a result of version upgrade. In addition, operation
procedures described in "Instruction Manual" may differ from the actual
procedures.
This model IS12S mobile phone complies with Japanese technical regulations and
international guidelines regarding exposure to radio waves. This mobile phone has
been designed in observance of the Japanese technical regulations regarding
exposure to radio waves (*1) and limits to exposure to radio waves recommended
by equivalent international guidelines.
These international guidelines were set out by the International Commission on
Non-Ionizing Radiation Protection (ICNIRP), which is in collaboration with the
World Health Organization (WHO), and the permissible limits include a substantial
safety margin designed to assure the safety of all persons, regardless of age and
health condition. The Japanese technical regulations and international guidelines
define the limits using a unit of measurement known as the Specific Absorption
Rate (SAR), which represents the average amount of radio frequency energy
absorbed by the human head. The SAR limit for mobile phones is 2.0 W/kg. The
highest SAR value for this mobile phone when tested for use at the ear is 0.806 W/
kg. There may be slight differences in SAR levels among individual products, but
they all satisfy the limit. The actual SAR of this mobile phone while talking on the
phone can be well below that indicated above. This is due to automatic changes in
the power level of the mobile phone to ensure it only outputs the minimum power
required to communicate with a base station. Therefore in general, the closer you
are to a base station, the lower the power output of the mobile phone.
This mobile phone can be used in positions other than against your ear. This
mobile phone satisfies the international guidelines when used with au Carrying
Case F Black (0105FCA) (sold separately) recommended by KDDI (*2).
In case you are not using the au Carrying Case F Black (0105FCA) (sold
separately), use a product that contains no metal parts, and one that can hold the
mobile phone at least 1.5 cm away from your body.
The World Health Organization has stated that present scientific information does
not indicate that use of mobile devices has any harmful effects on the human body.
They recommend that if you are still worried about your exposure then you can limit
your talk time or use a handsfree kit to keep the mobile phone away from your
head and body. If you would like to know more detailed information, please refer to
the WHO website.
(http://www.who.int/docstore/peh-emf/publications/facts_press/fact_english.htm)
Please refer to the websites listed below if you would like to know more detailed
information regarding SAR.
○Ministry of Internal Affairs and Communications website:
http://www.tele.soumu.go.jp/j/sys/ele/index.htm
○Association of Radio Industries and Businesses website:
http://www.arib-emf.org/index02.html (in Japanese only)
○au homepage:
http://www.au.kddi.com/
○Sony Ericsson Mobile Communications, Inc. website:
http://www.sonyericsson.co.jp/support/
*1 Technical regulations are defined by the Ministerial Ordinance Related to
Radio Law (Article 14-2 of Radio Equipment Regulations).
*2 Regarding the method of measuring SAR when using mobile phones in
positions other than against the ear, the international standard IEC62209-2
was set in March 2010. On the other hand, Japanese technical regulation is
currently under deliberation by the Committee for Radio Wave Utilization
Environment set up in the Information and Communication Technology
Group of the Advisory Committee on Information and Communications. (As
of March 2011)
■Trademarks
･"Bluetooth®" is a registered trademark owned by the Bluetooth SIG, Inc., and
Sony Ericsson is licensed to use this trademark.
･"Wi-Fi®" is a trademark or registered trademark of Wi-Fi Alliance®.
･Wi-Fi Protected Setup™and Wi-Fi Protected Setup logo are trademarks of
Wi-Fi Alliance®.
･The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.
･"Liquid Identity" logo, "Xperia", "PlayNow", "Timescape", "TrackID" and "Live
Ware" are trademarks or registered trademarks of Sony Ericsson Mobile
Communications AB.
･"APPNAVI" is a registered trademark of Sony Ericsson Mobile
Communications Japan, Inc.
･A technology of Gracenote Mobile MusicID is used for "TrackID".
･Music recognition technology and related data are provided by Gracenote®.
Gracenote is a business standard for music recognition technology and
related contents delivery.
For details, refer to the following web page: www.gracenote.com
CD and music data provided by Gracenote: Copyright © 2000 - present
Gracenote.
Gracenote Software: Copyright 2000 - present Gracenote.
This product and services may include one or several of the following US
Patent. #5,987,525, #6,061,680, #6,154,773, #6,161,132, #6,230,192,
#6,230,207, #6,240,459, #6,330,593, and other granted or applied patents.
Part of services are provided by Open Globe, Inc. for US patent (#6,304,523)
under license.
Gracenote and CDDB are registered trademarks of Gracenote, Inc.
Logo and logo type of Gracenote and "Powered by Gracenote" logo are either
registered trademarks or trademarks of Gracenote, Inc.
For information on the use of Gracenote services, refer to the following web
page: www.gracenote.com/corporate
･"Media Go" is a trademark or registered trademark of Sony Electronics Inc.
･"BRAVIA", "POBox", "Sony", "Exmor R for mobile" and "Exmor R for mobile" logo
are trademarks or registered trademarks of Sony Corporation.
･"xLOUD" is a trademark of Sony Corporation.
･"acro" is a registered trademark of Sony Ericsson Mobile Communications,
Inc.
･"POBox" is a co-developed technology of Sony Computer Science
Laboratories, Inc. and Sony Ericsson Mobile Communications Japan, Inc.
･"PlayStation" and "PlayStation" logo are trademarks or registered trademarks
of Sony Computer Entertainment Inc.
･microSDHC logo is a trademark of SD-3C, LLC.
･"Twitter" is a trademark or registered trademark of Twitter, Inc.
･"3GPP" is a trademark or registered trademark of ETSI.
･Google and Google logo, Android and Android logo, Android Market and
Android Market logo, Gmail, Google Maps, Google Talk, Google latitude,
Google Calendar, YouTube and YouTube logo, and Picasa are trademarks or
registered trademarks of Google, Inc.
･"Facebook" is a trademark or registered trademark of Facebook, Inc.
･"Ericsson" is a trademark or registered trademark of Telefonaktiebolaget LM
Ericsson.
･mixi and mixi logo are registered trademarks of mixi, Inc.
･DLNA is a trademark or registered trademark of the Digital Living Network
Alliance.
･HDMI, the HDMI Logo and High-Definition Multimedia Interface, are
trademarks or registered trademarks of HDMI Licensing LLC.
･"Microsoft", "Windows", "Outlook", "Windows Vista", "Windows Server",
"Windows Media" "Exchange" and "ActiveSync" are trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other
countries.
･This product contains technology subject to certain intellectual property
rights of Microsoft. Use or distribution of this technology outside of this
product is prohibited without the appropriate license(s) from Microsoft.
Notes on Android Market/au one Market/
applications
Specific Absorption Rate (SAR) of cell phones
Intellectual property rights
･Contains Adobe®Flash®Player technology by Adobe Systems Incorporated.
Adobe Flash Player Copyright © 1996-2012 Adobe Systems Incorporated. All
rights reserved.
Adobe, Flash and Flash logo are either registered trademarks or trademarks
of Adobe Systems Incorporated in the United States and/or other countries.
･FeliCa is a contactless IC card technology developed by Sony Corporation.
･FeliCa is a registered trademark of Sony Corporation.
･"Osaifu-Keitai®" is a registered trademark of NTT DOCOMO, INC.
･is a registered trademark of FeliCa Networks, Inc.
･"Jibe" is a trademark of Jibe Mobile K.K.
･Skype, associated trademarks and logos and the "S" symbol are trademarks
of Skype Limited.
･うたとも®is a registered trademark of Label Gate Co., Ltd.
･GREE and the GREE logo are registered trademarks of GREE, Inc. in Japan.
All other trademarks are the property of their respective owners.
･Rovi, G-GUIDE, G-GUIDE MOBILE and G-Guide related logos are
trademarks or registered trademarks of Rovi Corporation and/or its
subsidiaries in Japan.
･TRENDMICRO, VirusBuster are trademarks of Trend Micro Inc.
･Copyright © 2010 - Three Laws of Mobility. All Rights Reserved.
･This product is licensed under the MPEG-4 visual and AVC patent portfolio
license for the personal and non-commercial use of a consumer for (i)
encoding video in compliance with the MPEG-4 visual standard ("MPEG-4
video") or the AVC standard ("AVC video") and/or (ii) decoding MPEG-4 or
AVC video that was encoded by a consumer engaged in a personal and non-
commercial activity and/or was obtained from a video provider licensed by
MPEG LA to provide MPEG-4 and/or AVC video. No license is granted or shall
be implied for any other use. Additional information including that relating to
promotional, internal and commercial uses and licensing may be obtained
MPEG LA, LLC. ("See http://www.mpegla.com"). MPEG Layer-3 audio
decoding technology licensed from Fraunhofer IIS and Thomson.
･Other product and company names mentioned herein may be the trademarks
of their respective owners. In context, TM and ® mark may be omitted.
･Any rights not expressly granted herein are reserved. All other trademarks are
property of their respective owners.
This application or device contains software from Gracenote, Inc. of Emeryville,
California ("Gracenote"). The software from Gracenote (the "Gracenote
Software") enables this application to perform disc and/or file identification and
obtain music-related information, including name, artist, track, and title
information ("Gracenote Data") from online servers or embedded databases
(collectively, "Gracenote Servers") and to perform other functions. You may use
Gracenote Data only by means of the intended End-User functions of this
application or device.
You agree that you will use Gracenote Data, the Gracenote Software, and
Gracenote Servers for your own personal non-commercial use only. You agree
not to assign, copy, transfer or transmit the Gracenote Software or any
Gracenote Data to any third party. YOU AGREE NOT TO USE OR EXPLOIT
GRACENOTE DATA, THE GRACENOTE SOFTWARE, OR GRACENOTE
SERVERS, EXCEPT AS EXPRESSLY PERMITTED HEREIN.
You agree that your non-exclusive license to use the Gracenote Data, the
Gracenote Software, and Gracenote Servers will terminate if you violate these
restrictions. If your license terminates, you agree to cease any and all use of
the Gracenote Data, the Gracenote Software, and Gracenote Servers.
Gracenote reserves all rights in Gracenote Data, the Gracenote Software, and
the Gracenote Servers, including all ownership rights. Under no circumstances
will Gracenote become liable for any payment to you for any information that
you provide. You agree that Gracenote, Inc. may enforce its rights under this
Agreement against you directly in its own name.
The Gracenote service uses a unique identifier to track queries for statistical
purposes. The purpose of a randomly assigned numeric identifier is to allow
the Gracenote service to count queries without knowing anything about who
you are. For more information, see the web page for the Gracenote Privacy
Policy for the Gracenote service.
The Gracenote Software and each item of Gracenote Data are licensed to you
"AS IS." Gracenote makes no representations or warranties, express or implied,
regarding the accuracy of any Gracenote Data from in the Gracenote Servers.
Gracenote reserves the right to delete data from the Gracenote Servers or to
change data categories for any cause that Gracenote deems sufficient. No
warranty is made that the Gracenote Software or Gracenote Servers are error-
free or that functioning of Gracenote Software or Gracenote Servers will be
uninterrupted. Gracenote is not obligated to provide you with new enhanced or
additional data types or categories that Gracenote may provide in the future
and is free to discontinue its services at any time.
GRACENOTE DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND
NON-INFRINGEMENT. GRACENOTE DOES NOT WARRANT THE RESULTS
THAT WILL BE OBTAINED BY YOUR USE OF THE GRACENOTE SOFTWARE
OR ANY GRACENOTE SERVER. IN NO CASE WILL GRACENOTE BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY LOST
PROFITS OR LOST REVENUES.
© Gracenote, Inc. 2000-present
Gracenote®End User License Agreement
Soldby:KDDICORPORATION,OKINAWACELLULARTELEPHONECOMPANY
Manufacturedby:SonyEricssonMobileCommunicationsJapan,Inc
Forinquiries,call:CustomerServiceCenter
Forgeneralinformationandcharges (tollfree)
Fromfixed-linephones: Fromaucellphones:
Fromfixed-linephones: Fromaucellphones:
0120-977-033(exceptOkinawa)
0120-977-699(Okinawa)
Forloss,theftordamageandoperationinformation
(tollfree)
Incaseabovenumbersarenotavailable,
(tollfree)
PRESSINGZEROWILLCONNECTYOUTOANOPERATOR
A
FTERCALLING157ONYOURauCELLPHONE
withoutareacode
withoutareacode
32 33 34 35
36 37 38 39
40 41 42 43
44 45 46