Sony WAHT-SA10 - Wireless Audio Delivery System User manual

SON~
3-879-620-11 (1 )
Wireless
Surround Kit
Operating Instructions~
..
Manual de instrucciones __
.'
WAHT-SA10
s-masrer
Digital Amplifier
©2008 Sony Corporation
•••
• •
S-AIR
DIGITAL WIRELESS

Table of Contents
About This Operating Instructions 4
Overview 4
Unpacking 5
Hooking Up 6
Connecting the AC Power Cords
(Mains Leads) 8
Setting up the Wireless System 8
Troubleshooting 12
Specifications 13
Index to Parts 15
WARNING
To reduce the risk of fire or electric
shock,
do not expose this apparatus
to rain or moisture.
Do not install the appliance in aconfined space,
such
as abookcase or built-in cabinet.
To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
apparatus.
In door use only.
For wireless transceiver (EZW.
RT10)
This transceiver must not be co-located or
operated in conjunction with any other antenna
or
transmitter.
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled
equipment and meets the
FCC radio frequency
(RF) Exposure Guidelines in Supplement Cto
OET65. This equipment should be installed and
operated with at least 20 cm and more between the
radiator and person's body (excluding extremities:
hands, wrists, feet and ankles).
CAUTION: TO REDUCE THE RISK OF elECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PEASONNEL.
&This symbol is intended to alert the user
~ Ito the presence of uninsulated
"dangerous voltage" within the
product's enclosure that may be
of
sufficient magnitude to constitute arisk of electric
shock to persons.
Lt.
This symbol is intended to alertthe user
to the presence
of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
Owner's Record
The model and serial numbers are located on the
side exterior
of the unit. Record the serial number
in the space provided below. Refer to them
whenever you call upon your Sony dealer
regarding this product.
Model No. WAHT-SAlO
Serial
No., _
Date
of Manufacture Marking, Shock Hazard
Marking and Associated Graphical Symbols are
located on the bottom exterior.
The following FCC statement applies only to the
version
of this model manufactured for sale in the
USA. Other versions may not comply with FCC
technical regulations.
WARNING
This equipment has been tested and found to
comply with the limits for aClass Bdigital device,
pursuant to Part
15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in aresidential
installation. This equipment generates, uses, and
can radiate radio frequency energy and,
if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particularinstallation.
If this equipmentdoes cause
harmful interference to radio or television

reception, which can be detennined by turning the
equipment
off and on, the user is encouraged to try
to correct the interference by one or more
of the
following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the
equipment and receiver.
-
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/
TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install
in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such
as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose
of the
polarized orgrounding-type plug. Apolarized
plug has two blades with one wider than the
other. Agrounding type plug has two blades
and athird grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the pointwhere they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When acart
is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods
of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
Precautions
On power sources
Install this system so that the AC power cord
(mains lead) can be unplugged from the wall outlet
(mains) immediately in the event
of trouble.
On placement DIll
•Do not place the system in locations that are hot
and subject to direct sunlight, dusty, very humid,
or extremely cold.
•Use caution when placing the system on a
specially treated (waxed, oiled, polished, etc.)
floor, as staining or discoloration may result.
•Allow adequate air circulation to prevent
internal heat buildup.
•Do not place the system on surfaces (rugs,
blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation slots.
•Do not install the system near heat sources such
as radiators or air ducts,
or in aplace subject to
direct sunlight, excessive dust, mechanical
vibration or shock.
•Donot install the system in an inclined position.
It is designed to be operated in ahorizontal
position only.
•Keep the system away from equipment with
strong magnets, such
as microwave ovens, or
large loudspeakers.
•
Do not place heavy objects on the system.
•
If you use more than one set of S-AIR products,
position them away from each other to avoid
cross talk.
•Install this surround amplifier and S-AIR
products at least 50 cm away from people.

4
US
•To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
apparatus.
•
Do not place the system on carpet, as
discoloration may result.
•
If you use more than one surround amplifier, do
not place one on top
of the other.
On cleaning
Clean the cabinets only with asoft dry cloth. Do
not use any type
of abrasive pad, scouring powder
or solvent such as alcohol or benzene.
Safety
• If anything falls into the cabinet, unplug the unit
and have it checked by qualified personnel
before operating it any further.
•Unplug the unit from the wall outlet (mains)
if
you do not intend to use it for an extended period
of time. To disconnect the cord, pull it outby the
plug, never by the cord.
WAHT-SAlO is asurround amplifier for
Sony S-AIR products. The amplifier is for
models that have an "EZW-RTIO" or
"EZW -T100" slot on their rear panel.
This surround amplifier allows you
to use a
5.1 channel system (five speakers and one
subwoofer) or
7.1 channel system (seven
speakers and one subwoofer).
Enjoying a5.1 channel
system
S-AIR can avoid cluttered cords to keep
your room tidy.

Enjoying a7.1 channel
system
S-AIRmakes possible a7.1 channel system,
using two surround and two surround back
speakers.
®Front left speaker
®Front right speaker
©Center speaker
@Surround left speaker
®Surround right speaker
®Surround back left speaker
@Surround back right speaker
®Subwoofer
CD Surround amplifier
(for surround speakers)
oSurround amplifier
(for surround back speakers)
Surround amplifier
TA·SA100WR (1)
Speaker cord cover (1)
Speaker cord holder (1 )
Wireless adapter
Wireless transceiver (EZW-RTlO) (1)
Speaker cords (2)
Operating Instructions (1)

Inserting wireless
adapters
1Insert the wireless transceiver
(supplied) in the slot on the rear
of the surround amplifier.
(not supplied)
mmJ
•Insert the wireless adapter (not supplied)
with the S-AIR logo facing
up. Also,
make sure
the'" marks on the wireless
adapter (not supplied) and the slot on the
S-AIR main unit are aligned when
inserting.
•Do not touch the terminal
of the wireless
adapter.
The illustration of the rear panel of an
S-AIR main unit is an example. Not all
S-AIR main units look exactly the
same.
Rear panel
2Insert the wireless adapter (not
supplied) in the slot on the S-AIR
main unit.
If awireless adapter is not supplied
with your
S-AIR main unit, you can
purchase awireless transmitter EZW-
TlOO.
For details, refer to the operating
instructions
of the S-AIR main unit.
Hooking Up
om
•Insert the wireless transceiver (supplied)
with the S-AIR logo facing
up. Also,
make sure
the'" marks on the wireless
transceiver (supplied) and the slot on the
surround amplifier are aligned when
inserting.
•Do not touch the terminal
of the wireless
adapter.
Connect the surround amplifier to your
S-AIR main unit.
Before installing, make sure to
remove the AC power cords
(mains leads) of all S·AIR
products from wall outlets
(mains).

Connecting the speakers
Insert the connectors of the speaker cords (supplied) into their corresponding speaker jacks.
The connectors
of the speaker cords are the same color as their corresponding jacks. The
speakers shown are for illustration purposes only. Not all the speakers are identical.
r1
.I
ElW·RTlD
I(g) (g)
()
(g) (g)
() ()
@~@
~~r;
@C--@
0i~' 0
0l( ;0
';
~UJr~~1 ~~
@ @ @ @
Speaker (R:right) Speaker (L:left)
The connector and color tube of the speaker cords are the same color as the label of their
corresponding jacks. Be sure to match the speaker cords to the appropriate terminals on the
speakers: the speakercord with the color tube to
(±), and the speakercord without the color tube
to
8. Do not catch the speaker cord insulation in the speaker terminals.
Rear of speaker
~J~~
Connector
When connecting to the surround amplifier, insert the connector until it clicks.
-
•When you use this wireless surround kit, do not connect the speaker cord(s) to the surround speakerjack(s)
on your Sony Home Theatre System (DAV).
7
US

Cennlctlng thl Ae Pewlr Cords (Mal
Before connecting the AC powercords (mains leads) of your S-AIR main unit and the surround
amplifier to wall outlets (mains), make sure that all speakers are connected.
Seg Up the Wireless System
POWER
Sus
To use the wireless system, you need to set
up the surround amplifier and your S-AIR
main unit. Before setting, make sure that the
wireless adapters are correctly inserted in
the S-AIR main unit and surround amplifier.
Front panel
POWER /ON LINE
Indicator
PHONES jack
Rear panel
S-AIR 10 switch
SURROUND
SELECTOR switch
ID setting
By matching the ID of the surround
amplifier and your S-AIR main unit, you
can establish sound transmission. You can
also use multiple S-AIR products
by setting
adifferent ID for each product.
Setting up the S-AIR main
unit
1Turn on the S-AIR main unit.
The system turns on.
2Set upthe S-AIR main unit so it is
ready for ID setting.
3Select the ID for the S-AIR main
unit.
You can select any ill (A, B, or C).
For details, refer to the operating
instructions
of the S-AIR main unit.
Setting up the surround
amplifier
1Set the SURROUND SELECTOR
switch (SURROUND or
SURROUND BACK) of the
surround amplifier to match the
S-AIR main unit.
2Set the S-AIR 10 switch of the
surround amplifier to match the
10 (A, B, or C) of the S-AIR main
unit.

3Press POWER on the surround
amplifier.
The POWER /ON LINE indicator
turns green.
If not, see "Checking the
transmission status" (page 9).
4Set up the speakers.
If the S-AIR main unit has the Auto
Calibration function, perform Auto
Calibration.
If the S-AIR main unit
does not have the Auto Calibration
function, perform the appropriate
speaker setting.
For details, refer to the
operating instructions
of the S-AIR
main unit.
Checking the
transmission status
You can check the status of sound
transmission between the S-AIR main unit
and surround amplifier by checking the
POWER /
ON LINE indicator on the
surround amplifier.
POWER I ON Status
LINE indicator
Turns green Sound transmission is
established.
Flashes green Sound transmission
is not
established. Fordetails, see
"Troubleshooting"
(page 12).
Turns red The surround amplifier
does not output sound. For
details,
see
'Troubleshooting"
(page 12).
Turns off The surround amplifier
turns offor its protection
is
active. For details, see
"Troubleshooting"
(page 12).
Enjoying the sound by
using
headphones
You can enjoy the system's sound in aplace
away from the S-AIR main unit by
connecting the headphones to the PHONES
jack on the surround amplifier.
mmI
•When you connect headphones to the surround
amplifier, neither the surround amplifier nor the
S-AIR main unit outputs sound from the
system's speakers.
•The volume
of the S-AIR main unitis minimized
if you turn off the surround amplifier with
headphones connected, or radio reception is
poor. In either case, check radio reception, and
set the volume again.
gus

Preventing transmission
to neighbors (Pairing)
•Before the pairing operation
(example)
The sound transmission is establishedby the
ID.
If your neighbors also have S-AIR products
and their IDs are the same as yours, your
neighbors could receive the sound
of your
S-AIR main unit. To prevent this, you can
identify your S-AIR products by performing
the pairing operation.
S-AIR main unit
I
IDA
I
~
</
-
~
.</
---
J!
..........
'.J..J
'---'
PP
-----
..J/
----
)/)
..........
I
IDA
I I
IDA I
Surround S-AIR receiver
amplifier
Neighbor
Your room
S-AIR main unit No transmission
,..--t-.IDA
I
~
-
~
---
..........
'---'
p
-----
----
)
..........
..
,..-f-eID AII
IDA
I
Surround S-AIR receiver
amplifier
•After the pairing operation
(example)
Sound transmission is established between
the surround amplifier and the S-AIR main
unit that performed the pairing operation.
Pairing
1Turn on the S-AIR main unit and
the
surround amplifier.
The system turns on.
2Match the IDs of the S-AIR main
unit and the surround amplifier.
3Set up theS-AIR main unit so it is
ready for pairing.
For details, refer to the operating
instructions
of the S-AIR main unit.
The POWER /ON LINE indicator on
the surround amplifier flashes green.
4Press PAIRING on the rear panel
of the surround amplifier.
The PAIRING indicator flashes red
when pairing starts.
When sound transmission
is
established, the POWER /ON LINE
indicatorturns green and the PAIRING
indicator turns on.
If you use more than one surround
amplifier, perform Steps 3and 4for
those also.
Neighbor
Your room
10
US

em
• If you perfonn the pairing operation between the
surround amplifierand anotherS-AIR main unit,
sound transmission established by the ID is
canceled.
•Pairing will not be canceled unless you change
the ID setting.
ImI
• To press the PAIRINGbutton, aslim instrument,
such
as apaper clip, can be used.
Attaching the cover to
the surround amplifier
After connecting, you can attach the cover
to the surround amplifier to organize and
store excess speaker cords.
1Attach the speakercord cover by
sliding it down along the grooves
on the edges of the surround
amplifier.
Speaker cord cover
Surround
amplifier
Grooves
Push the speakercord coverdown until
you hear aclick. Turn the surround
amplifier upside down, and store the
cords in the speaker cord cover.
2Insert the tabs of the speaker
cord holder
in the slots of the
speaker cord cover, and press it
into place.
Speaker cord holder
em
•When detaching, remove the speaker cord
holder, then remove the speaker cord cover. To
remove the speaker cord holder, slightly press
the catch
of the holder and liftoff. To remove the
speakercordcover, slightly splay open the edges
of the cover and slide down.
•
Do not use excessive force to store the cords.
11
US

12
US
If you experience any of the following
difficulties while using the system, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Note that
if service personnel changes some
parts during repair, these parts may be
retained.
In the event of aproblem with the surround
amplifier, have aSony dealer check the
entire system together (system, speakers,
and wireless adapters).
Power
The power is not turned on.
•Check that the AC powercord (mains lead) is
connected securely.
The POWER ION LINE indicator does not
turn on.
Turn off the surround amplifier and
remove the AC power cord (mains lead) of
the surround amplifier, then check the
following items.
•Are the +and -speaker cords short-circuited?
•Is anything blocking the ventilation holes
of
the surround amplifier?
•After checking the above items and fixing
any problems, connect the AC power cord
(mains lead)
of the surround amplifier and
tum on.
If the cause of the problem cannot be
found even after checkingall the above items,
consult your nearest Sony dealer.
Sound
There is no sound.
Check the status of the POWER
ION LINE
indicator on the surround amplifier.
-turns green
•The speaker cord is not connected securely.
•Check the speaker connections and settings.
•The volume
of the S-AIR main unit is set to
minimum.
•The S-AIR main unit is in mute status.
•Depending on the source
or the settings of the
S-AIR main unit, the effect
of the speakers
may be less noticeable.
•Headphones are connected.
-flashes
green
•The S-AIR main unit is not turned on.
•The S-AIR main unit is paired to another
S-AIR product.
•The surround amplifier is paired to another
S-AIR main unit.
•Confirm the IDs
of the S-AIR main unit and
surround amplifier (page 8).
•Pairing operation is not completed.
•Sound transmission is poor. Move the
surround amplifier so that the POWER /ON
LINE indicator turns green.
•Move the system away from any other
wireless products.
•Stop using another wireless product.
•The wireless adapter is not inserted correctly.
-turns
red
•Change the SURROUND SELECTOR
switch (SURROUND or SURROUND
BACK)
of the surround amplifier to match
the S-AIR main unit.
No sound is heard from the S-AIR main
unit.
•Volume becomes the minimum when you
tum
off the surround amplifier with
headphones connected before you tumoffthe
S-AIR main unit
or if radio reception is poor.
In these cases, check radio reception, and set
the volume again.
Severe hum or noise is heard.
•Check that the S-AIRproducts are connected
securely.
•Check that the connecting cords are away
from atransformer or motor, and at least 3
meters (10 ft) away from your TV set or a
fluorescent light.
•Move your
TV away from the audio
components.
•Theplugs andjacksaredirty. Wipe them with
acloth slightly moistened with alcohol.
•Clean the disc.
No sound or only avery low-level sound is
heard from the speakers.
•Check the speaker connections and settings.
•Check the decoding mode setting.
•Depending on the source, the effect
of the
speakers may be less noticeable.
•Wireless setting
of the speaker is not correct.
• A 2 channel source is being played.
No sound
is heard or sound is cut off.
•The S-AIR main unit and/or the surround
amplifier is installed in aplace such as on a
metal shelf.
•Wireless LANs, amicrowave (oven) and
Bluetooth applications, etc. are placed near
the surround amplifier.

•Move away the other components from the
surround amplifier or turn off the other
components.
Operation
The system does not work normally.
•Disconnect the AC power cord (mains lead)
from the wall outlet (mains), then reconnect
after several minutes.
TA-SA100WR
(Surround amplifier)
AUDIO POWER SPECIFICATIONS
for the US model
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 3
ohm loads,
both channels
driven, from 120 -
20,000Hz; rated
50
watts per channel
minimum RMS
power, with no
more than 0.7 %
total harmonic
distortion from
250
milliwatts to rated
output.
Amplifier section
US models:
Surround mode (reference) RMS output power
143W (perchannel
at 3ohms, 1kHz,
10 % THD)
Other models:
Stereo mode (rated) 80 W+80 W(at
3ohms, 1kHz, 1%
THD)
Surround mode (reference)RMS output
power
143 W(perchannel
at 3ohms, 1kHz,
10 %THD)
*Depending on the source, there may be no
sound output.
Rated impedance: 3 - 16 Q
13
US

General
Powerrequirements
Power consumption
Dimensions (approx.)
Mass (approx.)
EZW-RT10
Communication System
Output
Frequency band
Modulation method
Power requirements
Dimensions (approx.)
Mass (approx.)
120 VAC, 60 Hz
On:
50W
85mmx 100mmx
330mm
(3
3
/8inx4inx
13 in)(w/h/d) (incl.
EZW-RTlO)
85mmx lOOmmx
345mm
(3 3/
8in x 4 in x
13 5/
8in) (w/h/d)
incl. speaker cord
cover and speaker
cord holder
1.7 kg
(3 Ib 12 oz)
inc
I. speaker cord
cover and speaker
cord holder
S-AIR
Specification
version 1.0
12.0mW
2.4000 GHz-
2.4835 GHz
DSSS
DC 3.3 V, 350 rnA
50mm x 13 mm x
60mm(2 in x
17/32 in x 2 3/
8in)
(w/h/d)
24g
(l oz)
•Halogenated flame retardants
•
are not used in
the printed
- '.
wiring boards.
•Over
85 %power efficiency of
amplifier block
is achieved
with the full digital amplifier,
S-master.
•Packaging cushions are made ofpaper.
14
US
Design and specifications are subject to change
without notice.
"S-AIR" and its logo are trademarks
of Sony
Corporation.

Surround amplifier
Front panel
Rear panel
12
POWER
3
POWER/ON LINE
PHONES
S-AI ID SPEAKER
8
mPHONES jack
~ POWER button (ON/OFF)
~ POWER /ON LINE indicator
@] PAIRING indicator
[ID PAIRING button
[§] Wireless transceiver (EZW-RT10) slot
[]J S-AIR ID switch
[ID SPEAKER Ljack
[ID SPEAKER Rjack
I1QI SURROUND SELECTOR switch
15
US

1111111111111111111111111111111111111111111111111111111
*3 8 7 9 6 2 0 1 1 *(1)
Sony Corporation Printed in China
http://www.sony.net!

\
SONY
. . http://www.sony.com/productregistration
You will find the product serial number on the main unit and the
. carton box.
3-089-014-02
/
©Sony Electronics Inc.
Thank you for purchasing this Sony product. Proper registration will
enable us to send you periodic mailings about new products and other
important announcements. Registering your product will also allow us
to contact you in the unlikely event that it will need adjustment
or modification. Please take the time to register your new product
at our website:
. If you have any operational questjons regarding your new purchase,
please contact your re~iler. For the location of a Sony dealer in your
area, or for any other questions, please call 1-800-222-S0NY(7669).
Thank you.

IIII1111111111 ~IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
4-557-172-03
SONY®
General Stereo/Hifi ComponentslTape Decks
CD Players/Mini Disc Players/Audio Systems
IHifi Audio I
LIMITED WARRANTY (u.s. Only)
Sony Electronics Inc. ("Sony") warrants this product against defects in material or workmanship for the time
periods and as set forth below. Pursuant to this Limited Warranty, Sony will, at its option, (i) repair the product
using new
or refurbished parts or (ij) replace the productwith a new or refurbished product. For purposes of this
Limited Warrahty, "refurbished" means aproduct
or partthat has been returned to its original specifications. In
the event of adefect, these are your exclusive remedies.
labor: For aperiod of one (1) yearfrom the original date of purchase of the product ("LaborWarranty"), Sony
will, at its option, repair
or replace with new or refurbished product, productdetermined to be defective. IfSony
elects
to replace the product afterthis LaborWarranty has expired but while the Parts Warranty below is still in
effect,
it will do so forthe applicable labor charge.
Parts: For aperiod
of one (1) year from the original date of purchase of product ("Parts Warranty"), Sony will
supply
new or refurbished replacement parts in exchange for parts determined to be defective.
This Limited Warranty covers
only the hardware components packaged with the Product. It does not cover
technical assistance
for hardware or software usage and itdoes notcover any software products whether or not
contained in the Product; any such software
is provided "AS IS" unless expressly provided for in any enclosed
software Limited Warranty.
Please refer to the End User License Agreements included with the Productfor your
rights and obligations with respect to the software.
Instructions: To obtain warranty service, you must deliver the product, freight prepaid, in either its original
packaging
or packaging affording an equal degree of protection to the Sonyauthorized service facility specified.
It is your responsibility to backup any data, software or other materials you may have stored or pr,e-
served
on your unit. It is likely that such data, software, or other materials will be lost or reformatted
during service and Sony will not be responsible for any such damage or loss. Adated purchase receipt is
required. For specific instructions on how to obtain warranty service for your product,
Visit Sony's Web Site:
www.sony.com/service
Or call the Sony Customer Information Service Center
1-800-222-S0NY (7669)
For an accessory
or part notavailable from your authorized dealer, call:
1-800-488-S0NY
(7669)
Repair IReplacement Warranty: This Limited Warranty shall apply to any repair, replacement part or replace-
ment product for the remainder of the original Limited Warranty period or for ninety (90) days, whichever is
longer. Any parts or product replaced underthis Limited Warranty will become the property of Sony.
This Limited Warranty onlycovers product issues caused bydefects
in material or workmanship during ordinary
consumer use; itdoes notcover product issues caused by any other reason, including but not limited
to product
issues due to commercial use, acts
of God, misuse, limitations of technology, or modification of or to any part of
the Sony product. This Limited Warranty does not cover Sony products sold AS IS or WITH ALL FAULTS or
consumables (such as fuses or batteries). This Limited Warranty is invalid if the factory-applied serial number
has been altered or removed from the product. This Limited Warranty is valid only in the United States.
LIMITATION ON DAMAGES: SONY SHALL NOT
BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES
FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT
IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states
do notallowthe exclusion or limitation of incidental or consequential damages, or allowlimitations
on
how long an implied warranty lasts, so the above limitations or exclusions may notapply to you. This Limited
Warranty gives you specific legal rights and you may have other rights which vary from state
to state.
Printed in China