Sony BRCSDP12 User manual

Outdoor and Indoor Dome Housings
Installation and Operation Instructions for the following models:
BRCSDP12
(1) Housing
(1) Supplied Parts
(1) Power connector (Heather/blower)
(1) Toolhead driver
(1) Operation Instruction Manual
Sony Electronics Inc.
1 Sony Drive
Park Ridge, NJ 07656
www.sony.com/security

!
!
Power 24 VAC, Class 2 Only
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
Add thread
sealing tape
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding the
weight of the entire unit.
1Using the security tool provided, open the housing by loosen-
ing the (3) captive security screws located on the housing ring
next to the lower clear dome (Figure 2).
Loosen three
security screws
holding dome
2Install the pan/tilt unit quick-release bracket. It is recom-
mended that this be done before installing the housing.
On the next page are instructions for mounting quick-release
brackets from selected manufacturers.
3It is recommended that the pan/tilt be installed at this time.
Connect to the quick-release bracket as shown and
secure per manufacturer directions.
4Clean the inside of the dome, with the text-wipe provided.
Reattach the housing dome and secure the (3) captive screws.
Do not overtighten the screws. Tighten only to the point at
which the gap between the ring and the housing top closes.
ELECTRICAL SPECIFICATIONS
1Carefully remove the housing from the packaging material.
Check to be sure all parts are present.
2This unit includes a 1 1/2" NPT housing coupling that can
be used with a standard 1 1/2" NPT pipe. The housing can
be used with other brackets designed with 1 1/2" male pipe
threads, such as the SNCWM20 wall mount bracket.
3Attach the housing coupling to the bracket or pendant pipe
(Figure 1).
NOTE: Pipe threads should be clean and rust free. Use a
sealer (such as Teflon™ tape or silicone sealer) on
the threads.
PREPARING PENDANT MOUNT MODEL
Figure 1
INSTALLING QUICK RELEASE BRACKET AND
PAN/TILT CAMERA ASSEMBLY (ALL MODELS)
Figure 2
INSTALLING THE HOUSING ASSEMBLY
1
© 2003 by Sony Corporation
10/13/04
For BRCSDP12
53 watts at 24 VAC (heater and blower)
Input Connectors:
BNC
(2) screw-down connectors
RJ-45 Connector
Refer to the camera's installation guide.
1Mount the housing assembly to the mounting bracket and
housing coupling. A safety cable is included with the housing
to temporarily hold it while making wiring connections. Loop
the safety cable over one of the set screws on the housing
coupling and make the appropriate connections using the (2)
screw-down connectors supplied.
2Undo the safety cable and twist the housing onto the housing
coupling. Secure all (3) setscrews provided on the housing
coupling (Figure 3).
3Clean the outside of the dome.
Twist and
Secure
Figure 3
Heater and Blower Only
Camera Power

2
© 2003 by Sony Corporation 10/13/04
CHART A WIRING COLOR CODE
POWER AND CONTROL INPUTS
1 Camera Power (12 VDC) Red
2 Camera Power (12 VDC) Orange
3 Heater & Blower Power (24 VAC) Yellow
4 Heater & Blower Power (24 VAC) Green
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
POWER
OPTIONAL
CHART B POWER AND CONTROL OUTPUTS
OPTIONAL
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
CAMERA POWER
Connect the power plug to the camera per Sony SNCRZ30N
instructions.
WIRING
NOTE: Failure to provide power to heater and blower will
void the warranties on both the housing and camera.
22 20 18 16 14 12 10
Total vA
consumed
Wire Gauge
24kVAC Wiring Distances
The following are the recommended maximum distances for 24VAC
with a 10% voltage drop (10% is generally the maximum allowable
voltage drop for AC powered devices).
35 56 90 143 228 362 576
50
1 Camera Power (12 VDC) Red
2 Camera Power (12 VDC) Orange
INSTALLING THE CAMERA
1Install the Sony BRC300 pan/tilt onto the quick release
bracket using the (4) screws provided with the camera
(Figure 4).
Figure 4
2Place the Sony BRC300 pan/tilt and quick release bracket
in the housing, sliding the three open screw slots over the
screws in the housing. Slide the bracket forward, then tighten
the captive screw on the bracket (Figures 5, 6, and 7).
Figure 5
Figure 6
Figure 7

!
!
5
© 2003 by Sony Corporation 10/13/04
1Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
2Retain Instructions - The safety and operating instructions
should be retained for future reference.
3Heed Warnings - All warnings on the unit and in the operat-
ing instructions should be adhered to.
4Follow Instructions - All operating and user instructions
should be followed.
5Electrical Connections - Only a qualified electrician should
make electrical connections..
6Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7Cable Runs - All cable runs must be within permissible
distance
8Mounting - This unit must be properly and securely
mounted to a supporting structure capable of sustaining the
weight of the unit. Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local
codes.
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the in stalla-
tion is intact. Failure to comply with the foregoing
could result in the unit separating from the support
structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
UNPACKING
SERVICE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with an arrowhead symbol, within
an equilateral triangle, is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
Unpack carefully. Electronic components can be damaged if improperly
handled or dropped. If an item appears to have been damaged in ship-
ment, replace it properly in its carton and notify the shipper.
Be sure to save:
1The shipping carton and packaging material. They are the safest
material in which to make future shipments of the equipment.
2These Installation and Operating Instructions.
If technical support or service is needed, contact Sony at the following
number:
TECHNICAL SUPPORT
8:15AM to 7:30PM (Eastern Time)
1-800-883-6817