Sony CDX-CA600 User manual
1
Ver 1.0 2001. 12
Model Name Using Similar Mechanism CDX-L300/L460X
CD Drive Mechanism Type MG-393XA-121//K
Optical Pick-up Name KSS-720A
SERVICE MANUAL
AEP Model
UK Model
CDX-CA600/CA600X
E Model
CDX-CA600X
CDX-CA600/CA600X
FM/MW/LW COMPACT DISC PLAYER
CD player section
Signal-to-noise ratio 90 dB
Frequency response 10 – 20,000 Hz
Wow and flutter Below measurable limit
Tuner section
FM
Tuning range 87.5 – 108.0 MHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 8 dBf
Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation 35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
MW/LW
Tuning range MW : 531 – 1,602 kHz
LW : 153 – 279 kHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity MW : 30 µV
LW : 40 µV
SPECIFICATIONS
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 50 W ×4 (at 4 ohms)
General
Outputs Power aerial relay control lead
Input Telephone ATT control lead
Tone controls Bass ±9 dB at 100 Hz
Treble ±9 dB at 10 kHz
Power requirements 12 V DC car battery
(negative earth)
Dimensions Approx. 178 ×50 ×177 mm
(w/h/d)
Mounting dimensions Approx. 182 ×53 ×161 mm
(w/h/d)
Mass Approx. 1.2 kg
Supplied accessories Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X115 (E model)
Note
This unit cannot be connected to a digital preamplifier or an equalizer.
Design and specifications are subject to change without
notice.
Photo: CDX-CA600X
• The tuner and CD sections have no adjustments.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-873-434-01
2001L0400-1
© 2001. 12
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
2
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
•CDX-CA600/CA600X: AEP, UK model
This label is located on the bottom of the chassis.
This label is located on the drive unit’s internal chassis.
CDX-CA600/CA600X
optical pick-up bloc
k
semi-fixed resistor
SERVICE NOTES
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2501-063-1)
CD-RW test disc TCD-W082L (Part No. J-2501-063-2)
NOTES ON CD-R/CD-RW DISCS
•You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
•Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
•You cannot play a CD-R/CD-RW that is not finalized∗.
∗A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
3
TABLE OF CONTENTS
1. GENERAL
Location of controls
(CDX-CA600/CA600X: AEP, UK model).............................. 4
Location of controls (CDX-CA600X: E model) ..................... 4
Connections (CDX-CA600/CA600X: AEP, UK model)......... 5
Connections (CDX-CA600X: E model).................................. 6
2. DISASSEMBLY
2-1. Panel (1) Assy, Sub ............................................................. 7
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 8
2-4. Heat Sink ............................................................................. 9
2-5. Chassis (T) Sub Assy .......................................................... 9
2-6. Lever Section .................................................................... 10
2-7. Servo Board....................................................................... 10
2-8. Shaft Roller Assy .............................................................. 11
2-9. Floating Block Assy .......................................................... 11
2-10. Optical Pick-up Block .......................................................12
MAIN BOARD CNP701
SERVO BOARD CN1
3. DIAGRAMS
3-1. IC Pin Description............................................................. 13
3-2. Block Diagram –CD Section–........................................... 15
3-3. Block Diagram –Tuner Section– ....................................... 16
3-4. Block Diagram –Display Section–.................................... 17
3-5. Circuit Boards Location .................................................... 17
3-6. Printed Wiring Boards –CD Mechanism Section–............18
3-7. Schematic Diagram –CD Mechanism Section– ................ 20
3-8. Printed Wiring Board –Main Section– .............................. 21
3-9. Schematic Diagram –Main Section (1/2)– ........................ 22
3-10. Schematic Diagram –Main Section (2/2)– ........................ 23
3-11. Printed Wiring Board –Display Section– .......................... 24
3-12. Schematic Diagram –Display Section–............................. 25
4. EXPLODED VIEWS
4-1. Chassis Section ................................................................. 28
4-2. Front panel Section ........................................................... 29
4-3. CD Mechanism Section (1) ............................................... 30
4-4. CD Mechanism Section (2) ............................................... 31
4-5. CD Mechanism Section (3) ............................................... 32
5. ELECTRICAL PARTS LIST ........................................ 33
CDX-CA600/CA600X
EXTENSION CABLE AND SERVICE POSITION
Whenrepairing orservicing thisset, connect thejig (extensioncable)
as shown below.
• Connect the MAIN board (CNP701) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-062-1).
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
4
CDX-CA600/CA600X SECTION 1
GENERAL This section is extracted
from instruction manual.
(CDX-CA600/CA600X: AEP, UK model) (CDX-CA600X: E model)
(CDX-CA600/CA600X: AEP, UK model) (CDX-CA600X: E model)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
7
CDX-CA600/CA600X
claws
4
claws
5
panel (1) assy, sub
3
claw
1
PTT 2.6x6
2
PTT 2.6x6
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
Note : Follow the disassembly procedure in the numerical order given.
2-1. PANEL (1) ASSY, SUB
2-1. PANEL (1) ASSY, SUB
(Page 7)
2-2. CD MECHANISM BLOCK
(Page 8)
2-5. CHASSIS (T) SUB ASSY
(Page 9)
2-6. LEVER SECTION
(Page 10)
2-8. SHAFT ROLLER ASSY
(Page 11)
2-9. FLOATING BLOCK ASSY
(Page 11)
2-10. OPTICAL PICK-UP BLOCK
(Page 12)
SET
2-7. SERVO BOARD
(Page 10)
2-3. MAIN BOARD
(Page 8)
2-4. HEAT SINK
(Page 9)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
8
CDX-CA600/CA600X
3
screw (+BTT)
4
screws (+BTT)
1
PTT 2.6x8
5
MAIN board
2
PTT 2.6x
8
1
PTT 2.6x6
6
PTT 2.6x
6
7
bracket (CD)
2
PTT 2.6x6
5
CD mechanism block
4
CNP701
3
2-2. CD MECHANISM BLOCK
2-3. MAIN BOARD
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
9
CDX-CA600/CA600X
4
chassis (T) sub assy
3
P 2x3
2
P 2x3
1
Unsolder the
lead wires.
black
red
white
6
heat sink
1
PTT 2.6x8
2
PTT 2.6x8
4
PTT 2.6x8
3
PTT 2.6x12
5
PTT 2.6x
8
2-5. CHASSIS (T) SUB ASSY
2-4. HEAT SINK
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
10
CDX-CA600/CA600X
5
special screws
1
CN3
2
Removal the solders.
3
P 2x3
4
loading motor assy
7
SERVO board
6
special screw
8
connector
optical pick-up bloc
k
4
claws
2
IN SELF SW board
7
lever (L)
3
tension spring (LR)
6
lever (R)
5
guide (disc)
1
special screw
2-6. LEVER SECTION
2-7. SERVO BOARD
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
11
CDX-CA600/CA600X
1
tension spring (KF1)
7
compression spring (FL)
6
floating block assy
8
compression spring (FL)
4
Fit lever (D) in the
direction of the arrow.
2
damper (T)
3
damper (T)
5
Turn loading ring in the
direction of the arrow.
Fig. 1
1
tension spring (RA)
2
arm (roller)
3
retaing ring (RA)
4
shaft retainer
5
shaft roller assy
retaing ring (RA) arm arm
washer washer shaft retainer
shaft retainer
2-9. FLOATING BLOCK ASSY
2-8. SHAFT ROLLER ASSY
• When installing, take note of the positions
arm (roller) and washers. (Fig. 1)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
12
CDX-CA600/CA600X
1
P 2x3
4
P 2x3
5
spring (feed), plate
6
shaft (feed) assy
2
sled motor assy
3
optical pick-up block
2-10. OPTICAL PICK-UP BLOCK
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
13
CDX-CA600/CA600X
3-1. IC PIN DESCRIPTION
•IC801 MN101C49KCF (SYSTEM CONTROL)
Pin No. Pin Name I/O Pin Description
1 VREF– — Ground for A/D converter power supply
2 VSM I S-meter voltage detection signal input from tuner unit (TU601)
3 NC I Connect to ground.
4 KEYIN1 I Key signal input
5 KEYIN0 I Key signal input
6 RC IN0 I Rotary commander key signal input from remote in jack (CNP801)
7 QUALITY I Noise detection signal input from RDS decoder (IC601)
8 MPTH I Multipass detection signal input
9 FUNCSEL I Destination set up detection signal input (“L”: CDX-CA600X, “H”: CDX-CA600)
10 VREF — A/D converter power supply
11 VDD — Power supply (+5 V) input pin
12 OSCOUT O High speed clock signal output (18.432 MHz)
13 OSCIN I High speed clock signal input (18.432 MHz)
14 VSS — Ground for power supply
15 XIN I Low speed clock signal input (32.768 kHz)
16 XOUT O Low speed clock signal output (32.768 kHz)
17 MMOD I Memory mode select signal input (Input to “Low” (single chip mode).)
(Connect to ground.)
18 LCDSO O LCD serial data signal output to LCD driver (IC501)
19 LCDCE O LCD chip enable signal output to LCD driver (IC501)
20 LCDCKO O LCD serial clock signal output to LCD driver (IC501)
21 CD TSO O CD servo IC serial data signal output
22 CD TSI I CD servo IC serial data signal input
23 CD TCKO O CD servo IC serial clock signal output
24 SYSRST O System reset signal output to bus interface (IC803)
25 BUS ON O Bus on signal output to bus interface (IC803)
26 KEYACK I Key acknowledge detection signal input
27 DAVN I RDS data block sync detection signal input
28 BU IN I Back up power supply detection signal input
29 SIRCS I Remote signal input from remote control receiver (IC552)
30 CD SELFSW I CD mechanism self load position detection switch signal input from self switch (SW2)
31 CD PACK I CD text pack sync signal input from CD servo (IC1)
32 NIH I Connect to power supply.
33 RESET I microcomputer reset signal input from reset IC (IC802) “L”: reset
34 NOSESW I Connect to power supply.
35 BEEP O Beep signal output to power amp (IC401)
36 NCO O Not used. (Open)
37 TESTIN I Test mode detection signal input
38 ACCIN I Accessory power supply detection signal input
39 NCO O Not used. (Open)
40 TELATT I Telephone ATT detection signal input
41 NIH I Connect to power supply.
42 BUSSO O Sony-Bus serial data signal output to bus interface (IC803)
43 BUSSI I Sony-Bus serial data signal input from bus interface (IC803)
44 BUSCKO O Sony-Bus serial clock signal output to bus interface (IC803)
45 I2CSIO I/O I2C bus serial data signal input/output
46 NCO O Not used. (Open)
47 I2CCKO O I2C bus serial clock signal output
48 NC O Not used. (Open)
49 TUNON O Tuner power supply control signal output
50 PW ON O System power supply control signal output
SECTION 3
DIAGRAMS
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
14
CDX-CA600/CA600X
Pin No. Pin Name I/O Pin Description
51 TSTB O CD text parameter strob signal output to servo IC (IC1)
52 RFOK I RF OK signal input from servo IC (IC1)
53 CD RST O Reset signal output to servo IC (IC1)
54 A0 O Command/parameter identification signal output to servo IC (IC1)
“L”: Command, “H”: Parameter
55 STB O Data strob signal output to servo IC (IC1)
56 X EN O Crystal oscillation control signal output to servo IC (IC1)
57 LIMIT I CD Mechanism in-limit switch signal input from limit switch (SW4)
58 PH1 I CD Mechanism PH1 detection signal input Not used in this set.
59 D SW I CD Mechanism down switch signal input from down switch (SW1)
60 INSW/PH2 I CD Mechanism disc-in switch detection signal input from disc-in switch (SW3)
61 PH3 I CD Mechanism PH3 detection signal input Not used in this set.
62 CD LM LO O CD Mechanism loading motor control signal output to loading motor drive (IC2)
63 CD LM EJ O CD Mechanism eject motor control signal output to loading motor drive (IC2)
64, 65 NC O Not used. (Open)
66 AMPATT O Power amp ATT control signal output to power amp (IC401)
67 AMPON O Power amp standby control signal output to power amp (IC401)
68 CDMD ON O CD mechanism deck power supply control signal output
69 ATT O System ATT control signal output
70 VOLATT O Electrical volumeATT control signal output to electrical volume (IC402)
71 – 75 NC O Not used. (Open)
76 NC I Not used. (Open)
77 COL SEL I Color select switch signal input “H”: Green, “L”: Amber
78 NC O Not used. (Open)
79 XCD ON O CD on signal output “H”: Play, “L”: Loading or standby
80 – 85 NC O Not used. (Open)
86 EE SIO I/O EEPROM serial data signal input/output
87 EE CKO O EEPROM serial clock signal output
88 NC O Not used. (Open)
89 FLASH W I Flash microcomputer write detection signal input “L”: Write mode
90 NS MASK O Noise mask signal output
91 AD ON O Key power supply control signal output
92 DOORIND O Sub panel power supply control signal output Not used in this set. (Open)
93 ILLON O Illumination power supply control signal output
94 NOSE SW I Front panel with/without detection signal input “L”: Panel with, “H”: Panel without
95 DAVSS — Ground pin
96 RE IN1 I Rotary encoder signal input Not used in this set. (Open)
97 RE IN0 I Rotary encoder signal input Not used in this set. (Open)
98 RC IN1 I Rotary commander shift key signal input from remote in jack (CNP801)
“L”: Shift key on
99 NC O Not used. (Open)
100 DAVDD — Power supply pin (+5 V)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
15 15
CDX-CA600/CA600X
84
85
82
83
16
12
D/A
CONV
TRACKING
ERROR
FORCUS
ERROR
9
1
OSC
EFM
DEMOD
SERVO
CTL
RF
EQ
52
56
54
55
DSUB CODE
PROCESS
8
7
6
5
4
3
2
56
59
30
60
57
68
79
21
22
23
55
54
53
52
I/F
87
86
97
98
LD
DRIVE
Q1
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
LOADING
MOTOR
DRIVE
6
5
23
2
15
16
17
18
13
14
11
12
9
10
26
62 63 64 65
63
62
33
CDMD ON
SWITCH
Q913,914
CD ON
SWITCH
Q915
CD+5V
REG
Q916,D927
CD DRIVE+6V
REG
Q912,D926
M902
(SLED)
M901
(SPINDLE)
M903
(LOADING)
SW3
(DISC IN)
SW2
(SELF)
SW4
(LIMIT)
SW1
(DOWN)
X1
16.9344MHz
OPTICAL PICK-UP
KSS-720A
I-V
CONV.
CDL
STB
AO
CD_TSO
31 CD_PACK
51 TSTB
CD TSI
CD TCKO
CD_RST
RFOK
XEN
D SW
INSW/PH2
CD_SELFSW
LIMIT
CD_LM _LO
CD_LM_ EJ
CDMD ON
XCD ON
R-CH
TUNER
SECTION
A
23 24
M
M
M
2RESET
S801
(RESET)
1
IC802
BU+5V
BATT
D925
LOUT
ROUT
PACK
TSTB
TSI
TSCK
SI
RFOK
SO
SCK
STB
AO
XTALEN
RST
RESET
A
C
B
D
E
F
PD
LD
B
D
A
C
E
F
PD
A+5V
LD
APC
FCS-
FCS+
TRK+
TRK-
SL-
SL+
SP+
SP-
LD-
LD+
FOCUS
COIL
TRACKING
COIL
FD
TD
SD
MD
LOAD
EJECT
SYSTEM CONTROL
IC801(1/3)
RF AMP,DIGITAL SERVO
DIGITAL SIGNAL PROCESSOR
IC1
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING MOTOR DRIVE
IC2
FD
TD
SD
MD
• Signal path
:CD
• R-ch is omitted due to
same as L-ch.
A+5V
AU+5V
D+5V
DR+6V
3-2. BLOCK DIAGRAM — CD SECTION —
(Page 16)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
1616
CDX-CA600/CA600X
PJ601
(ANTENNA) 2 10
1
ANTFM MPX
CDL
8
AM DET
14
S-METER
12
I2C SDA
13
I2C SCL
17
E2PROM SDA
18
9
E2PROM SCL
RDS DET
ANTAM
TUNER UNIT
TU601
2
45
47
70
14
15
20
21
18
11
13
1
3
30
SYSTEM CONTROL
IC801 (2/3)
ELECTRONIC VOLUME
IC402
AUX L
OUT LF
29
OUT LR
28
OUT RF
27
OUT RR
35
BEEP
ATT
67
69
AMP ON
66
AMP ATT
40
TEL ATT
38
ACC IN
CD L
MPX
R-CH
AM
LEVEL
MPIN
SDA
SCL
MUTE
17 QUAL
VOL ATT
7QUALITY
90 MS MASK
VSM
I2C SIO
I2C CKO
FUNCSEL
EE SIO
EE CKO
MPTH
DAVN
AUDIO OUT REAR
CD
SECTION
A
LINE MUTE
SWITCH
Q904,905
Q402
MUTE
R-CH
Q401
MUTE
22 MUTE
4STBY
16 AUX
11
12 5
3
9
7
POWER AMP
IC401
1
-1
-2
-5
-6
-3
-4
9
2
10
CNP901
R-CH
PJ401
FL+
FL-
RL+
RL-
4
12
FR+
FR-
3
11
RR+
RR-
16 +B (BATT)
13 ATT
5AMP R
6
8
19
ANT R
GND
R-CH
BATT
F901
10A
TEL
ATT
Q901
TUNER +5V
REG
Q911,D918,919
NOISE
SUPPRESSOR
D601
BUFFER
Q601
TUNER ON
SWITCH
Q909,910
+8V REG
Q906,D917
POWER ON
CONTROL
Q907,908
AMP B+
CONTROL
SWITCH
Q921
AMP B+
SWITCH
Q920
AMP B+
CONTROL
SWITCH
Q917
AMP B+
SWITCH
Q922
7ACC
15 TEST
49
50
TUN ON
37
TEST IN
ACC
DETECT
Q902, D914
PW ON
24
SYSRST
25
BUSON
43
BUSSI
44
BUSCKO
42
BUSSO
28
BU IN
9
87
86
BATT
BATT DET
Q801,D801,802 BATT
+5V REG
Q93,D916 BATT+5V
+8V
TUNER
+8V
TUNER
+5V
BATT
17
18
L
R
AUDIO OUT FRONT
R-CH
L
R
BUS AUDIO IN
R-CH
L
R
•Signal path
:FM
:MW/LW
:CD
•R-ch is omitted due to same as L-ch.
CDRR-CH 2CD R
16 MPX
4OSCD
5OSCI
LVIN
SDA
SCL
20
9
10
MPTH 2
DAVN 8
RDS DECODER
IC601
BUS INTERFACE
IC803
8
27
13 RST
12 BUSON
8DATA OUT
11 CLK IN
9DATA IN
10 B/U-C
6
DATA I/O
4
CLK
2
RST
3
BATT
8
7
5
6
4
2
3
1
BATT
CNJ801
BUS
CONTROL IN
CA600X
CA600
BU+5V
NOISE AMP
IC602
MS MASK
SWITCH
Q602
X601
4.332MHz
DELAY BATT
D921,922
1
BUSON
3-3. BLOCK DIAGRAM — TUNER SECTION —
(Page 15)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
17 17
CDX-CA600/CA600X
KEY MATRIX
S501-521
KEY
ACTIVE
Q803
REMOTE
RECEIVE
CNP801
(REMOTE IN) IC552
X802
32.768kHz
15
16
12
13
518
20
194
26
91
98
6
29
SYSTEM CONTROL
IC801 (3/3)
LCD DRIVE
IC501
KEY IN0 DATA
CLK
CE
LCD SO
LCD CKO
LCD CE
ILL ON
SWITCH
Q919
ILL B+
REG
Q918
KEY IN1
KEY ACK
AD ON
RC IN1
RC IN0
SIRCS
XIN
XOUT
OSC OUT
93
ILL ON
BATT
ILL+5V
OSC IN
X801
18.432MHz LED549,550
LCD BACK
LIGHT
64
63
62
COM1
COM4
LCD
LCD501
ILL+5V
ILL+5V
D531-559
D809
D807
()
KEY
ILLUMINATION
()
D561-589
KEY
ILLUMINATION
()
52
|
55
2
I
25
•
27
|
38
•
40
I
47
S2
I
S25
•
S27
|
S38
•
S40
I
S47
|
DATA
CLK
CE
LED
DRIVE
Q502
1
P1/S1
BATT
61
INH
LED DRIVE
SWITCH
Q503
LED
DRIVE
Q501
CA600
CA600
CA600X
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
MAIN board
tuner unit
(TU601)
DISPLAY board
SERVO board
IN SELF SW board SPEAKER board
SL SW board
3-5. CIRCUIT BOARDS LOCATION
• Waveforms
— Servo Board —
(MODE: CD PLAY)
1
2
3
IC1 ts (PACK)
IC1 uj (RFO)
1.2Vp-p
4
Approx. 100mVp-p
IC1 oa (FEO)
0V
5
Approx. 100mVp-p
IC1 od (TEO)
2Vp-p
16.9344MHz
IC1 wd (XTAL)
5Vp-p
0V
3.2msec
— Main Board —
2
3
32.768kHz
IC801 qh (XOUT)
18.432MHz
IC801 qs (OSCOUT)
2.2Vp-p
5Vp-p
1
4.332MHz
IC601 4(OSCD)
5.2Vp-p
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
1818
CDX-CA600/CA600X
3-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 17 for Circuit Boards Location.
1
A
B
C
D
E
F
G
H
I
J
23456789101112
SW1
CN2
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
• % : indicates tolerance.
•f: internal component.
•C: panel designation.
•A: B+ Line.
• Powervoltage isdc14.4V andfedwith regulateddcpower
supply from ACC and BATT cords.
• Voltagesare takenwith aVOM (Inputimpedance 10MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F: FM
f: MW/LW
J: CD
for printed wiring boards:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•x: parts mounted on the conductor side.
•a: Through hole.
•: Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side: Partson thepatternface sideseenfromthe
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
Note: The components identified by mark 0or dotted line
with mark 0are critical for safety.
Replace only with part number specified.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
19 19
CDX-CA600/CA600X
1
A
B
C
D
E
F
G
H
I
J
234567891011121314
TP8
C45
C4
C26
C37
TP6
TP1
TP2
TP4
TP5
TP87
TP86
TP57
TP77
TP11
TP79
TP83
TP70
TP9
TP27
TP12
TP78
TP10
TP81
TP84
TP54
TP25
TP24
TP37
TP39
TP36 TP38
TP40
TP45
TP22
TP88
TP41
TP46
FB3
TP21
TP17
TP20
TP42
TP19
TP28
TP90
C41
TP29
C44
TP73 TP32
TP48
TP71
TP51
TP49
TP52
TP55
TP75
TP53
TP56
TP43
TP58
TP61
TP74
TP68
TP80
TP7
TP62
TP91
TP63
C40
TP66
TP64
TP69
TP72
TP50
TP26
TP3
TP59
TP76
TP18
TP89
TP30
R8
R9
R5
R7
R12
R14
R15
R10
R17
R18
R19
R20
R22
FB6
FB7
FB1
FB2
TP92
FB4
C3
C5
C6
C8
C9 C10
C11
C13
C14
C16 C18
C19
C24
C25
C29
C34
C36
C38 C35
C21
C22
C30
C23
C1
C27
R21
TP47
C15
C20
TP35
TP23
R24
R6
C17
TP82
TP44
Q1
R26
TP34
R25
R3
TP16
TP85
IC1
IC2
C43
R30
R29
X1
TP60
CN3
CN1
SW3
SW2
SW4
(Page 21)
Ref. No. Location
IC1 E-7
IC2 H-7
Q1 C-6
•Semiconductor
Location
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
2020
CDX-CA600/CA600X
IC B/D
IC B/D
TP77
TP78
R29
R30
C43
TP79
TP80
TP81
TP82
TP83
TP84
CN2
CN3
TP85
M902
M901
SW2 TP4
TP2
TP3
M903
TP87
TP86
TP9 TP8
R3 R26
C4
TP10
C13
R5
C11
C10
C8
TP7
TP92
R6
TP17
TP20
TP16
TP19
R25
TP21
TP18
R24
R7
TP6
C17
FB1
TP11
TP12 C9
C14
TP89
C19
C20 C23
R9
R8
TP22
TP23
TP24
TP25
TP88
FB4
C26
TP32
R14
R15
TP30
R12
R10
TP91 C37
TP90
TP29
TP28
TP26
TP27
R21
R22
TP34
TP35
TP36
TP46
TP37
TP38
TP39
TP40
TP41
TP42
TP43
TP44
TP45
FB2
CN1
R18
R19
R20
R17
TP66
FB7
FB6
TP62
TP47
TP63
TP48
TP49
TP64
TP50
TP51
TP52
TP68
TP53
TP69
TP54
TP70
TP55
TP71
TP56
TP72
TP57
TP73
TP58
TP74
TP59
TP75
TP60
TP76
TP61
X1
SW3
SW4
CN13
Q1
C18
IC2
FB3
IC1
SW1
TP1
TP5
C44
C40
C1 C5
C3 C6
C15
C16
C41
C27
C45
C34
C29
C25
C36
C38
C35
C24
C30
C22
C21
•Refer to page 17 for Waveforms.
3-7. SCHEMATIC DIAGRAM —CD MECHANISM SECTION —•Refer to page 26 for IC Block Diagrams.
(Page 23)
Note:
• Voltage is dc with respect to
ground under no-signal conditions.
no mark : CD PLAY
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
Other manuals for CDX-CA600
2
This manual suits for next models
1
Table of contents
Other Sony Car Receiver manuals
Sony
Sony XR-C7220 User manual
Sony
Sony XR-C7220R User manual
Sony
Sony XR-CA350X Marketing s & diagrams User manual
Sony
Sony XR-M500R User manual
Sony
Sony CDX-GT63UIW - Fm/am Compact Disc Player User manual
Sony
Sony CDX-5100 Product guide
Sony
Sony CDX-V7800X Product guide
Sony
Sony ST-SE570 User manual
Sony
Sony CDX-GT517EE User manual
Sony
Sony MEX-GS600BT User manual
Sony
Sony CDX-MP50 Product guide
Sony
Sony CDX-565MXRF Operating Instruction correction: multi-session... Product guide
Sony
Sony CDX-4250 - Fm/am Compact Disc Changer System User manual
Sony
Sony CDX-3100 User manual
Sony
Sony CDX-RA650 User manual
Sony
Sony CDX-R505X - Synchro-flip Detachable Face User manual
Sony
Sony BluetoothH MEX-BT5100 User manual
Sony
Sony CDX-F5705X - Fm/am Compact Disc Player Product guide
Sony
Sony CDX-C7850 User manual
Sony
Sony CDX-GT06 - Fm/am Compact Disc Player User manual
