Sony XR-C5300X Product guide

FM/AM Cassette
Car Stereo
Installation/Connections
Installation/Connexions
XR-C5300X
XR-C5305
Sony Corporation © 2000

Parts list
The numbers in the list are keyed to those in the instructions.
® @ @
® ® ®
x4 x2
®
®
Caution
Cautionary notice for handling the bracket (_).
Handle the bracket carefully to avoid injuring your fingers.

Connections
Caution
• This unit is designed for negative ground 12 V DC operation only.
• Be careful not to pinch any wires between a screw and the body of the car or this unit or between any
moving parts such as the seat railing, etc.
• Before making connections, disconnect the ground terminal of the car battery to avoid short circuits.
• Connect the yellow and red power input leads only after all other leads have been connected.
• Be sure to connect the red power input lead to the positive 12 V power terminal which is energized
when the ignition key is in the accessory position.
•Run all ground wires to a common ground point.
• Connect the yellow cord to a free car circuit rated higher than the unit's fuse rating. If you connect this
unit in series with other stereo comportents, the car circuit they are connected to must be rated higher
than the sum of the individual component's fuse rating. If there are no car circuits rated as high as the
unit's fuse rating, connect the unit directly to the battery. If no car circuits are available for connecting
this unit, connect the unit to a car circuit rated higher than the unit's fuse rating in such a way that if the
unit blows its fuse, no other circuits will be cut off.
• When installing a car without ACC (accessory) position on the ignition key switch, connect the red
power input lead to the + 12 V power terminal which is energized at all times with the yellow lead.
Warning when installing in a car without ACC (accessory) position on
the ignition key switch
Be sure to press _on the unit for two seconds to turn off the clock display after turned off the
engine.
When you press _ momentarily, the clock display does not turn off and this causes battery wear.
Reset button
When the installation and connections are complete, be sure to press the reset button with a ball-point
pen, etc.

Installation
Precautions
•lfyou mount other Sony equipment with this unit, it is better to mount this unit in the lower position.
• There must be a distance of at least 15 cm between the cassette slot of the unit and shift lever in order to insert a
cassette easily. Choose the installation location carefully so the unit does not interfere with gear shifting and
other driving operations.
• Choose the installation location carefully so that the unit will not interfere with normal driving
• Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20
How to detach and attach the front panel
Before installing the unit, detach the front panel,
[] To detach
Before detaching the front panel, be sure to press _. Press _, then slide the front panel to the right
side, and pull out the left side.
[] To attach
Place the hole (_) in the front panel onto the spindle _) on the unit as illustrated, then push the left side in.
M
6

Mounting example
Installation in the dashboard
12
Bend these claws
outward for a tight fit, if
necessary.
Plier ces grilles pour
assurer une prise
correcte si necessaire.
3
®
Mounting the unit in a Japanese car
You may not be able to Install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.
TOYOTA ®
max, size
5xSmm
Dimension
max. 5xB mm
to dashboard/centerconsole
au tableau de bord/consolecentrale
Bracket (_
Support max. size
5x8mm
Dimension
max. 5 ×8mm
Bracket
Support
Existing parts supplied with your car
Pieces existantes fournies avec la voiture
Note
Toprevent malfunction, instal/onlywith the supplied screws(_.

34Dashboard
Tableau de bord
Fire wall
Paroi ignifuge
NISSAN ®
max. size
5×Bmm
Dimension
max. 5x 8 mm
to dashboard/center console
au tableau de bord/console centrale
Bracket
Suppo_
Bracket
SuppoK
max. size
5x8mm
Dimension
max. 5 x8 mm
Pieces existantes rournies avec la voiture
9

Connection example
Supplied with XA-C30
Foumi avec le XA-C30
from car antenna
de I'antenne de la voiture
Fuse (10 A)
Fusible (10 A)
RCA pin cord (not supplied)
Cordon b broche RCA (non fourni)
Toconnect to AMP REMOTE IN of the
optional power ampfifier
Thisconnection is only for amplifiers.
Connecting any other system may damage
the unit.
Pour effectuer le raccordement _AMP
REMOTE IN de I'ampfificateur de puissance
en option.
Cette connexion s'applique uniquement
aux amplificateurs. Le branchement de
tout autre systeme risque d'endommager
I'appareil.
Le_
Gauche
Blue/white striped
AMP REM Raye bleu/blan¢
Max. supply current 0.3 A
Courant max. fourni 0,3 A
White
.,.o0
_ _ White/black striped
Ray_ blanc/noir
Blue
Bleu
10

Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
Insert with the cord upwards.
Ins6rez ave(: le cable vers le haut,
Rotary commander RM-X4S (not supplied)
Satellite de commande RM-X4S (non fourni)
Blue
Bleu ANT REM
Max. supply current 0.1 A
Courant max. fourni 0,1 A
to the power antenna control lead or power supply lead of antenna booster
amplifier
Notes
• It is not necessary to connect this lead it"there isno power antenna or antenna
booster, or with e manually-operated telescopic antenna.
•When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes on
the control leads."
11

Le. 0
Gauche
White
Raye blanc/noir
Right O
Droit
Grey
Grey/black striped
Raye gris/noir
'e.
Gauche
Green
Vert
Green/black striped
Raye vert/noir
Right
Droit Purp,e
Mauve
Purple/black striped
Ray_ mauve/noir
to a metal place in the car
First connect the black ground lead, then connect the
yellow and red power input leads. Black
Noir
Red
Rouge
Yellow
Jaune
Notes on the control leads
•The power antenna control lead (blue) supplies + 12 V DC when you turn on the tuner or when you activate
the A TA (Automatic Tuner ActivaUon) function.
• A power antenna without relay box cannot be used with this unit.
•When your car has a built-in FM/AM antenna in the rear/side glass, it is necessary to connect the power
antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing
antenna booster. For details, consult your dealer,
Memory hold connection
When the yellow power input lead is connected, power will always be supplied to the memory circuit even
when the ignition key is turned off.
Notes on speaker connection
•Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities. Otherwise,
the speakers may be damaged.
• Do not connect the terminals of the speaker system to the car chassis, and do not connect the terminals of
the right speaker with those of the left speaker.
• Do not attempt to connect the speakers in parallel.
• DO not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing so
may damage the active speakers. Be sure to connect passive speakers to these terminals.
12

Red
Rouge
to the +12 V power terminal which is energized at the accessory position of
the ignition key switch,
Notes
•If there is no accessoryposition, connect to the _12Vpower (battery)
terminal which is energized at all times.
Be sure to connect the black ground lead to it first
•When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes
on the control leads."
Yellow to the +12 V power terminal which is energized at all times
Jaune _Be sure to connect the black ground lead first.

Connection diagram
Equipment used in illustrations (not supplied)
Front speaker Power amplifier TV monitor
Rearspeaker CD/MD chaneer
For connecting two or more changers, the source selector XA-C30 (optional) is necessary.
Dans le cas du raccordement de deux changeurs ou plus, le selecteur de source XA-C30 (optionnel) est
indispensable.
14

Notes
•Be sure to connect the ground cord before connecting the amplifier.
•If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will
be deactivated.
15

Sony Corporation Printed in USA