Sony CSS-HD2 - Cyber-Shot Station Digital Camera... User manual

SONY:
3-286-877-11 (1)
-
eyber-shotStation
eyber-shot $J}](mJ{f/lE
Operating Instructions IB
Mode d'emploi -----'_
Manual de instrucciones ---'_
ffm~B,ijt! _
ffmi~B,ij~ _
A.g~~Ai _
CSS-HD2
©2008 Sony Corporation

English
Before operating the product, please read this manual thoroughly and retain it for future reference.
WARNING
To reduce fire or shock hazard, do not expose the unit to rain or
moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER·SERVICEABLE PARTS INSIDE.
REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be
of sufficient magnitude to constitute
arisk
of electric shock to persons.
This symbol
is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
2-GB

IMPORTANT SAFEGUARDS
For your protection, please read these safety instructions completely before operating the appliance, and
keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the
appliance,
or the one described in the operating instructions and adhere to them.
Use·······;,,·;···········
Power Sources
This set should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of electrical power supplied to your home, consult your dealer or local power company. For
those sets designed to operate from battery power,
or other sources, refer to the operating instructions.
Polarization
This set may be equipped with apolarized ac power cord plug (a plug having one blade wider than the other).
This plug will fit into the power outlet onlyone
way. This is asafety feature. If you are unable to insert the
plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact your electrician to
have asuitable outlet installed.
Do
not defeat the safety purpose of the polarized plug by forcing it in.
Overloading
Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can
result in fire
or electric shock.
Object and Liquid Entry
Never push objects of any kind into the set through openings as theymay touch dangerous voltage points or
short out parts that could result in afire or electric shock. Never spill liquid of any kind on the set.
Attachments
Do not use attachments not recommended by the manufacturer, as they may cause hazards.
Cleaning
Unplug the set from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol
cleaners. Use acloth lightly dampened with water for cleaning the exterior
of the set.
Water and Moisture
Do not use power-line operated sets near water -for example, near abathtub, washbowl, kitchen sink, or
laundrytub, in awet basement, or near aswimming pool, etc.
Power-Cord Protection
Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to the plugs, receptacles,
and the pointwhere the cord exits from the appliance.
Accessories
Do not place the set on an unstable cart, stand, tripod, bracket, or table. The set mayfall, causing serious
injuryto achild
or an adult, and serious damage to the set. Use only acart, stand, tripod, bracket, or table
recommended by the manufacturer.
Ventilation
The slots and openings in the cabinet are provided for necessary ventilation. To ensure reliable operation of
the set, and to protect it from overheating, these slots and openings must never be blocked or covered.
-Never cover the slots
and openings with acloth or other materials.
-Never blockthe slots
and openings by placing the set on abed, sofa, rug, or other similar surface.
-Never place the set
in aconfined space, such as abookcase, or built-in cabinet, unless properventilation is
provided.
- Do not place the set near or over aradiator or heat register, or where it is exposed to direct sunlight.
-
3-GB

Lightning
For added protection for this set during alightning storm, or when it is left unattended and unused for long
periods
of time, unplug it from the wall outlet and disconnect the antenna or cable system. This willprevent
damage to the set due to lightning and power-line surges.
.- .. .
',S~rvlce
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to qualified service personnel under the follOwing
conditions:
-
When the power cord or plug is damaged or frayed.
-
If liquid has been spilled or objects have fallen into the set.
-
If the set has been exposed to rain or water.
-
If the set has been subject to excessive shock bybeing dropped, or the cabinet has been damaged.
-
If the set does not operate normallywhen following the operating instructions. Adjust only those controls
that are specified in the operating instructions. Improper adjustment
of other controls may result in damage
and will often require extensive work byaqualified technician to restore the set to normal operation.
-
When the set exhibits adistinct change in performance -this indicates aneed for service.
Servicing
Do not attempt to service the set yourself as opening or removing covers may expose you to dangerous
voltage
or other hazards.
Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer
that have the same characteristics as the original parts.
Unauthorized substitutions may result in fire, electric shock,
or other hazards.
SafetyCheck
Upon completion of any service or repairs to the set, as the service technician to perform routine safety
checks (as specified by the manufacturer) to determine that the set
is in safe operating condition.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual couldvoid your
authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for aClass Bdigital device, pursuant
to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference
in aresidential installation. This equipment generates, uses, and can radiate radio frequency
energy and,
if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in aparticular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined byturning the equipment offand on, the user is encouraged to
try to correct the interference by
one
or more of the follOwing measures:
-Reorient
or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on acircuit different from that to which the receiver is connected.
-Consult the dealer
or an experienced radio/TV technician for help.
The supplied interface cable must be used with the equipment in order to comply with the limits for adigital
device pursuant to Subpart B
of Part 15 of FCC Rules.
4-GB

Amoulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced, afuse
of the same rating as the supplied one and
approved by ASTA or BSI to BS1362, (Le., marked with <g> or ~ mark) must be used.
If the plug supplied with this equipment has adetachable fuse cover, be sure to attach the fuse cover after you
change the fuse. Never use the plug without the fuse cover.
If you should lose the fuse cover, please contact
your nearest Sony service station.
This
product has been tested and found compliant with the limits sets out in the EMC Directive for using
connection cables shorter
than 3meters (9.8 feet).
Attention
The electromagnetic field at the specific frequencies may influence the picture and sound of this unit.
Notice for the customers in the countries applying EU Directives
The manufacturer ofthis product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan.
The Authorized Representative for EMC and product safety
is Sony Deutschland GmbH, Hedelfinger Strasse
61, 70327 Stuttgart, Germany. For any service
or guarantee matters please refer to the addresses given in
separate service or guarantee documents.
Disposal of Old Electrical &Electronic Equipment (Applicable in
the European Union and other European countries with separate
collection systems) -
This symbol on the product or on its packaging indicates that this product shall
not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling
of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment
and human health, which could
otherwise be caused by inappropriate waste handling
of this product. The recycling
of materials will help to conserve natural resources. For more detailed information
about recycling of this product, please contactyour local Civic Office, your
household waste disposal service
or the shop where you purchased the product.
5-GB

Disposal of waste batteries (applicable in the European Union and
other European countries with separate collection systems)
This symbol on the battery or on the packaging indicates that the batteryprovided with
this product shall not be treated as household waste.
By ensuring these batteries are disposed of correctly, you will help prevent potentially
negative consequences for the environment and human health which could otherwise be
caused by inappropriate waste handling
of the battery. The recycling of the materials will
help to conserve natural resources.
In case
of products that for safety, performance or data integrity reasons require a
permanent connection with an incorporated battery, this battery should be replaced by
qualified service staffonly. To ensure that the batterywill be treated properly, hand over
the
product at end-of-life to the applicable collection point for the recycling of electrical
and electronic equipment.
For all other batteries, please view the section
on how to remove the batteryfrom the
product safely.
Hand the battery over to the applicable collection pointfor the recycling of waste batteries.
For more detailed information about recycling
of this product or battery, please contact
your local Civic Office, your household waste disposal service or the shop where you
purchased the product.
6-GB

Table of contents
Notes on using the Cyber-shot Station 8
Features 9
Trademarks 9
Identifying the parts 10
Set up 12
Placing the camera on the Cyber-shot Station 14
Removing the camera from the Cyber-shot Station 14
Charging the battery pack 14
Viewing images
on a TV screen 15
Remote Commander functions 16
Care and maintenance 17
Changing the battery
of the Remote Commander 17
Troubleshooting
18
Specifications 19
7-GB
-

Noteson using the Cyber-shot Station
Refer to the operating instructions for your camera as well as this manual.
The Cyber-shot Station is not adust-proofed, moist-proofed, or water proofed product.
The CSS- HD2 can be used with the DSC-T300/T75/T70/T2/W3001W170/W150/W1301W125/W120/W115/
WIlD digital still cameras. Not all of the above models are available in all countries and regions.
About the station plates
• The Cyber-shot Station is supplied with 5station plates that are
compatible
with various digital cameras (hereinafter referred to as the
"camera"). See page 12 for further details.
•Be sure
to set the correct station plate that is compatible with your camera
before using.
If you set the wrong station plate, the 110 unit could be
damaged.
•
The illustration in this manual shows the combination of DSC-T300 and
station plate for DSC-T300.
Precautions on use and storage locations:
Do not use or keep the Cyber-shot Station in locations subject to the following conditions. Otherwise, the
Cyber-shot Station could malfunction.
•Locations subject
to extreme high temperature
Temperatures
in a hot sun or closed automobiles during summer may be extremely high, causing
deformation or malfunction of the Cyber-shot Station.
•Locations
under direct sunlight or near heaters
This
may cause deformation or amalfunction of the Cyber-shot Station.
•Locations subject
to vibration
•Locations subject
to strong magnetism
•Locations subject
to dust particles in asandyplace or the beach
Precautions on use:
•Even if the CHARGE lamp is not lit, the unit is not disconnected from the AC power source (mains) as long
as it is
connected to the wall outlet (wall socket). If some trouble occurs while using the unit, immediately
shut off the power by disconnecting the plug from the wall outlet (wall socket).
•Use
the nearest wall outlet to get the AC Adaptor plugged in. If any malfunctions occur using the product,
unplug the AC Adaptor to cut off the power source.
•
The set is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet,
even
if the set itselfhas been turned off.
•
Do not use the AC Adaptor placed in a narrow space, such as between awall and furniture.
•
Do not use the Cyber-shot Station in locations that are subject to strong radio waves or radiation. Images
may not be played backproperly.
•Avoid
other metallic objects from coming in contact with the connecting parts of the Cyber-shot Station
and the power cord. It may cause a short circuit.
Precautions on recorded data:
•Please note that Sony will not be liable for recorded data such as images and audio data if you cannot record
or play back due to a malfunction of the camera, recording media, or the Cyber-shot Station.
8-GB

Features
When you place acamera on the Cyber-shot Station, you can use the Cyber-shot Station in the following way.
• You can view the images of the camera in high definition by connecting the Cyber-shot Station to ahigh
definition
TV. Images can be viewed in standard definition on anormal TV.
• You can easilyview images on a TV screen with the wireless Remote Commander.
Using the Remote Commander, you can operate the followings:
-Viewing images
-Slide Show
-Playback zoom
-Display the images in index display and switch the way to display images to "Folder:' "Date View:'
or
"Favorites" (except for DSC- T7S/T70/T2/W130/W12S/W120/WllS/WllO).
-Display the images in index display and search for the image by 'i\ll people:' "Children," "Smiles:' or
"Infants" (except for DSC- T7S/T70/T2/W130/W12S/W120/Wl lS/Wl 10).
•The Cyber-shot Station can charge the batterypack inside the camera faster
than the batterycharger
supplied with the camera when you simply place the camera
on it.
Trademarks
• Cyber-shot and "Cyber-shot Station" are trademarks of Sony Corporation.
•In addition, system and product names used in this manual are, in general, trademarks or registered
trademarks
of their respective developers or manufacturers. However, the 1M or ®marks are not used in all
cases
in this manual.
•
9-GB

Identifying the parts
Cyber-shot Station
_-------Camera front guide
1/0 unit -----~~~~~~jtl
~~~~~~=;;~--protection cover
Positioning marker
-~~-""",,~""'J~ ~ Detach this cover
before use.
. .-.:~:;.... Remote sensor
POWER lamp ~
CHARGE lamp __HDOUTPUT lamp
DC IN jack
T.·~~:'-"'-AV OUTjack
~~~
Station plate
Positioning marker B ---------- .......
Positioning marker A -------_
_----Camera side guide
• The eyber-shot Station is supplied with 5station plates. Be sure to attach the correct station plate before
use.
See page
12 for further details.
10-GB

Remote Commander
The functions of the Remote Commander differ depending on the camera you use.
When using DSC-T75/T70/T2, the Remote Commander of the Cr.ber-shot Station functions the same as the
Remote Commander
of CSS-HDI, except for the functions ofthe ~ (Slide Show) button and the control
buttons.
Also, some buttons do not function at all. For further information on the functions
of the control buttons,
refer to the operating instructions supplied with the camera.
•
i-+---- Playback Zoom (6)1
Index0 button
~--- POWER button (CAMERA)
!-""+----- PlaybackZoom (e) button
....... i----- Control buttons
(IJ..~ 1-t4/~/.)
H+-4----- HOME button'
2
r;;&;;~§§§0i----V UP buttonl
VDOWN button '2
WZOOM button'
2
-----
~ (Slide Show) button ---
MENU button
HD/SD button'2
VIEW MODE button'
1
----
FACE button '1
*1 These functions are not supported for DSC-T75/T70/T2/W130/WI25/WI20/W1l5/WllO.
*2 These functions are not supported for DSC-T75/T70/T2.
ll-GB

Setup
Using aright-sliding station plate (such as
HD2-A)
Sliding to the left
®Hold the eyber-shot Station with one hand.
Hold the camera side guide
of the station
plate with the other hand
and slide the station
plate until it
is pushed in all the way.
•See the table in step 1for the sliding direction.
Sliding to the right
Using aleft-sliding station plate (such
as
HD2-B)
·I· ..• ~~··.·.I
Sonylogo
r··.·.'··,·~·.".···,····~.··,·.···,.·.··.·,·'.···'" ,.' .. ," .. ,.,'"
... '.."" ".'"",:-:: .:'-::";;'.:.
Model name Plate name Sliding
direction
DSC-T300 HD2-A
Right
DSC-Wll 0
DSC-W115
DSC-W120 HD2-B Left
DSC-W125
DSC-W130
DSC-W150 HD2-C Left
DSC-W170
DSC-W300
HD2-D
Left
DSC-T2
DSC-T70 HD2-E Right
DSC-T75
Bottom side
Plate name
Select the station plate corresponding with your
camera.
Preparing the Cyber-shot Station
1Selectastation plate.
The station plates have afront side and bottom
side.
Front side
2Attach the station plate.
CD Hold the station plate on the front side (the
side with the Sonylogo) facing you, and place
it
on the I/O unit of the eyber-shot Station
as if you place it over the protection cover
attached
on the I/O unit.
12-GB

®The station plate will sink in when it is slid all
the way to the correct position.
You will hear
a
dick when the plate is attached properly.
Ifthe station plate does not sink in properly,
evenlypush down
on its left/right sides.
•The positioning marker A
on the station plate
and positioning marker
on the Cyber-shot
Station will be aligned.
@Detach the protection cover of the I/O unit.
•Before you place acamera on the Cyber-shot
Station, be sure to detach the protection cover.
Detaching the station plate
Hold the Cyber-shot Station with one hand. Hold
the camera side guide
of the station plate with the
other
hand and pull the station plate upward.
3Connect the supplied AC Adaptor to the DC
IN jack ofthe Cyber-shot Station.
The POWERlamp of the Cyber-shot Station
lights up.
AC Power cord
(mains lead)
To use yourCyber-shot Station abroad
-Power sources
You can use the Cyber-shot Station and the AC
Adaptor (supplied) in any country
or region where
the power supply
is within 100 Vto 240 VAC
50/60 Hz.
Use acommercially available AC plug adaptor,
ifnecessary, depending
on the design of the wall
outlet (wall socket). •
IAC-lS5 KJ= - qm: -8
AC plug adaptor
(not supplied)
Do
not use an electronictransformer (travel
converter), as this
may cause amalfunction.
Preparing the Remote Commander
Notes on the Remote Commander
•The Remote Commander is powered by abutton
type lithium battery (CR2025) installed at the
factory. An insulation sheet is inserted to avoid
the batteryexhaustion. Remove the insulation
sheet before using the Remote Commanderfor
the first time.
Insulation sheet -~4
•Point the remote sensor of the Cyber-shot Station
away from strong light sources such
as direct
sunlight
or overhead lightings. Otherwise, the
Remote Commander may not function properly.
13-GB

• The Remote Commander range is less than
five meters (for indoor use). Point the Remote
Commander at the remote sensor of the Cyber-
shot Station. Try adjusting the angle
of the
Remote
Commander if you cannot operate the
Cyber-shot Station.
Placing the camera on the
Cyber-shotStation
Remove the Adaptor ring, the Conversion lens,
etc.
from the camera.
Attach
the camera as shown below.
• Be sure to turn off the camera before placing it on
the Cyber-shot Station.
•
When attaching the camera, make sure to insert
the camera straight down.
'~'Tips
•Make sure that the camera is securely attached to
the Cyber-shot Station.
14-GB
Removing the camera from
the Cyber-shot Station
•Hold the Cyber-shot Station down when you
remove the camera from the Cyber-shot Station.
"Notes
• When removing the camera, make sure to lift the
camera straight up. It may damage the camera
or
the Cyber-shot Station when some extra force is
added to the front
or the sides.
Charging the batterypack
Place the camera with the battery pack
inserted on
the Cyber-shot Station.
Charging starts automatically. The CHARGE lamp
of the Cyber-shot Station lights up.
•
When the camera is turned on, the Cyber-shot
Station cannot charge the battery pack.
•
When the charging reaches to Normal charge*,
the CHARGE lamp goes off.
*Recording and playback time with Normal
charge
is approximately 90% of Full charge.
•For the time
of the full charge for acompletely
discharged batteryat the temperature
of 25 °C
(77
OF), see the table below.
DSC -T300fT75fT70fT2 Approx.
160 minutes
DSC-
Approx.
W3001W1701W15011W1301
W1251W1201W1151W110
230 minutes
-It may take longer to charge, depending on the
charging condition and environment.

Viewing images on TVs otherthan high-
definition
TV
Connect the AN OUT jack of the Cyber-shot
Station and the audiolvideo inputjacks
of the
TV.
3Turn on the TV and set the input switch to
the inputconnected in step 1.
4 Press ~/~ on the Control buttons of the
Remote Commander to select the image.
You can also select the image bypressing ~/~
on the Control buttons of the camera.
•The Cyber-shot Station
is compatible with both
NTSC and PAL TV systems. For further details,
see the operating instructions supplied with the
camera.
I. :j •..
CE
Red •Audio
~
White ~
.. Yellow <iJ) Video
AN connecting cable
•Turn offthe TV before connecting the Cyber-
shot Station and
TV with the Component
AN Cable.
• The signal format to be output from the AN
OUT jack depends on the camera setting.
•
To view the 1080i format images, you need a •
TV compatible with 1080i format.
•The audio to be output from the Cyber-shot
Station via the
NV OUT jackis monaural.
•The Cyber-shot Station is not compatible with
the
S- VIDEO connecting cable.
2Turn on the power by pressing the [E
(playback) button of the camera or the
POWER button on the Remote Commander.
'~'Tips
•The buttons on the camera or the Remote
Commander may not function immediately
after the camera
is attached to the Cyber-
shot Station. This occurs when the camera
is
booting up and is not amalfunction. Wait for
about
10 seconds.
•Audio
~
ey
• PB/CB
• PRICR
_"'lIIIlI-.Green
'==f--" Blue
Red
Component
AN Cable
,,==---,r---~ Red
--<IIIlIDWhite
1Viewing images on ahigh-definition TV
Connect the AN OUT jack of the Cyber-shot
Station
and the Component AV jacks of the TV.
On battery life
• The batterylife is limited. Battery capacity
decreases little bylittle
as you use it more and
more, and as time passes. If the batteryoperating
time seems shortened considerably, aprobable
cause
is that the batterypack has reached the end
of its life. Buy anew batterypack.
• The batterylife varies according to how it
is stored and the operating conditions
and
environment in which each battery pack is used.
Viewing images on a TV
screen
You can playback images byconnecting the Cyber-
shot Station to the
TV with the AN connecting
cable (supplied) or the Component AIV Cable
(supplied).
Refer to the operating instructions supplied with
the
TV for connection.
UNotes
•After attaching the camera to the Cyber-shot
Station, the CHARGE lamp mayblink slowly for
3
to 10 seconds. This indicates communication
between the camera and the Cyber-shot Station,
and it is not amalfunction.
•
If CHARGE lamp does not light or blinks for
more
than 10 seconds, refer to "Troubleshooting':
Chargingtemperature
The temperature range for charging is 0 °C to
40°C (32 OF to 104 OF). However, to provide
maximum battery efficiency, the recommended
temperature range when charging
is 10°C to
30 °C (50
OF to 86 OF).
1S-GB

Remote Commander
functions
The functions of the Remote Commander differ
depending
on the camera you use.
For further information, refer to the operating
instructions supplied with the camera.
Slide show
You can play back aseries of still images recorded
with your camerabyonlypressing the
~ (Slide
Show) button
on the Remote Commander.
1Turn on the power of the camera by
pressing
the ~ (playback) button of
the camera or the POWER button on the
Remote Commander.
2Press the ~ (Slide Show) button on the
Remote Commander.
The Slide Show settings screen appears.
•The Slide Show settings screen may not be
displayed
on some models even if you press
the
~ (Slide Show) button. The Slide Show
will start in the preset conditions. For further
details about the setting method, refer to
the operating instructions supplied with the
camera.
3Use the control buttonson the Remote
Commander
to change the settings of the
Slide Show.
4Use the control buttons on the Remote
Commander
to select [OK] and press the
center. button or press the g(Slide
Show)
button on the Remote Commander.
16-GB
To cancel Slide Show
Press the ~ (Slide Show) button on the Remote
Commander again.
•For further information, refer to the operating
instructions supplied with the camera.
Switching the view mode
You can change the index display bypressing the
VIEW MODE button
on the Remote Commander.
•Except for DSC-T7S/T70/T2/W1301W12S/W1201
WllS/Wl10.
1Turn on the power of the camera by
pressing the ~ (playback) button of
the camera or the POWER button on the
Remote Commander.
2 Press the VIEWMODE button on the
Remote Commander.
The view mode screen appears.
3Use the control buttons on the Remote
Commander
to select the desired view
modeand press the center. button.
The images are displayed in index mode using
the view mode you just selected.
• When you press the VUP button and V DOWN
button on the Remote Commander, you can
perform the following functions in each view
mode.
-Date View mode:
Display the previous date and next date.
-Folder mode:
Display the previous folder
and next folder.
-Favorites mode:
Display the previous page and next page.
Filter by Faces
You can search the images recorded with various
faces by pressing the
FACE button on the Remote
Commander.
•Except for DSC-T7S/T70/T2/W1301W12S/W1201
WllSlWllO.
1Turn on the power of the camera by
pressing the ~ (playback) button of
the camera or the POWER button on the
Remote Commander.
2 Press the FACE button on the Remote
Commander.
The Search images menu appears.

3Use the control buttons on the Remote
Commander
to select the search condition
and press the center. button.
The images are displayed in index mode in
accordance with the search condition.
•For further information, refer to the operating
instructions supplied with the camera.
Switching between HD and SO
You can switch the TV display between high-
definition video (HD)
and other than high-
definition video (SD) by pressing the HD/SD button
on the Remote Commander.
•Except for DSC-T75/T70/T2.
1Turn on the power of the camera by
pressing the lB (playback) button of
the camera or the POWER button on the
Remote Commander.
2 Press the HD/SD button on the Remote
Commander.
•Every time you press the HD/SD button, the
setting will change alternately between
HD and
SD.
•The HD-OUTPUT lamp (blue) of the Cyber-shot
Station lights up while the
HD video is viewed
on a TV
•For further information, refer to the operating
instructions supplied with the camera.
Wide Zoom Display
You can display astill image with an angle of view of
4:3 or 3:2 to those of 16:9 bypressing the W ZOOM
button on the Remote Commander, which is the
same as the wide zoom function
of the camera.
•For DSC-T75/T70, the Wide Zoom functions
whenyou press the Tbutton
on the Remote
Commander.
•Except for DSC-T2.
1Turn on the power of the camera by
pressing the lB(playback) button of
the camera or the POWER button on the
Remote Commander.
2 Press the WZOOM button on the Remote
Commander.
•Every time you press the W ZOOM button, the
setting will change alternately between Wide
Zoom and Normal modes.
•The Wide
Zoom mode is canceled when you turn
off the camera or the shooting mode is switched.
•Some functions of the Remote Commander will
be unavailable when you are using the Wide
Zoom function.
•For further information, refer to the operating
instructions supplied with the camera.
Care and maintenance
Clean the Cyber-shot Station with asoft cloth
slightly moistened with water
or tepid water, and
wipe the surface with a dry cloth. Do not use any
type
of solvent such as thinner, alcohol or benzine
as this may damage the surface.
Changing the battery of the
Remote Commander
WARNING
Battery may explode if mistreated. Do not recharge,
disassemble,
or dispose of in fire.
•
When the lithium batterybecomes weak, the
operating distance
of the Remote Commander
may shorten,
or the Remote Commander may
not function properly.
In this case, replace the
batterywith aSony CR2025 lithium battery. Use •
of another battery maypresent arisk of fire or
explosion.
For the State of California, USA only
Perchlorate Material -special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium batterycontains
perchlorate.
CAUTION
Replace the battery with the specified type only.
Otherwise, fire or injury may result.
Replacing the button type lithium
battery
*Do not use any batteries other than CR2025.
<D Pull out the battery holder while pushing the
tab
on the holder.
®Put anew battery into the holder with its +
side facing upward.
®Insert the holder into the Remote
Commander until it clicks.
17-GB

Troubleshooting
If any problems occurwith your products, refer to the following solutions.
If the problem persists, contact your Sony dealer.
Symptom
Unable to charge the battery pack or the
CHARGE lamp fails to light.
Cause/Solution
•The camera is turned on.
-+ Turn the camera off.
•The
AC Adaptor is disconnected.
-+ Connect the AC Adaptor properly.
•The camera
is not placed on the Cyber-shot Station correctly.
-+ Place the camera correctly.
•The batterypack
is not installed correctly.
-+ Install the battery pack correctly.
•The battery pack
is completely charged.
•The batterypack installed into the camera
is inapplicable.
-+ Install the batterypack compatible with your camera.
The CHARGE lamp blinks fast, or blinks •The batterypackinstalled into the camera is inapplicable.
for
more than 10 seconds. -+ Install the battery pack compatible with your camera.
•The connection
is not correct. The camera is not placed
correctly
on the Cyber-shot Station.
-+ Remove the camera from the Cyber-shot Station and
reconnect the
AC Adaptor. After the CHARGE lamp goes
off, place the camera on the Cyber-shot Station.
Unable
to tum on the camera, or
it suddenly gets turned off.
The images cannot be played back on
aTV:
Buttons on the Remote Commander
do not work, and no operations can be
performed.
Unable to attach the camera on the
Cyber-shot Station or the camera is
unstable.
18-GB
•The camera is not placed on the Cyber-shot Station correctly.
-+ Place the camera correctly.
•The
AC Adaptor is disconnected.
-+ Connect the AC Adaptor properly.
•The HD output setting is incorrect.
-+ Refer to the operating instructions supplied with the
camera, and set the
HD output setting correctly.
•The Component A/V Cable
or A/V connectingcable from the
Cyber-shot Station is not connected properlyto the
TV.
-+ Connect the cable properly or correct the setting.
•The camera
is not placed correctly on the Cyber-shot Station.
-+ Place the camera correctly.
•The
AC Adaptor is disconnected.
-+ Connect the AC Adaptor properly.
•The battery in the Remote Commander
is dead.
-+ Replace the battery with anew one.
•The station plate
is not attached properly.
-+ Confirm that the station plate is compatible with your
camera and attach it properly.

Specifications
Cyber-shot Station
Input/Output connectors
• AN OUT jack: Component, Video/audio output
connector
•
DC IN jack
•
I/O unit
General
Dimensions (Approx.):
124 x48 x
78 mm
(5 x 1 15/16 x 3 1/8 in.)
(w/h/d)
Mass (Approx.): 110 g(3.9 oz.)
(including astation plate)
Operating temperature:
o°C to 40°C
(32 of to 104 OF)
Storage temperature:
-20°C to +60 °C
(-4 of to +140 OF)
ACAdaptor
Input rating: 100 Vto 240 V, AC 50/60 Hz,
llW
Output rating: 4.2 V DC
See the label on the AC Adaptor
for other specifications.
Dimensions (Approx.):
48 x29 x
81 mm
(115/16 x 1 3/16 x 3 114 inches)
(w/h/d, excluding projecting
parts)
Mass (Approx.): 130 g
(5 oz)
(excluding
AC Power cord)
Operating temperature:
o°C to 40°C
(32 of to 104 OF)
Storage temperature:
-20°C to +60 °C
(-4 of to +140 OF)
Included items
•Cyber-shot Station (CSS-HD2) (1)
•Wireless Remote Commander(RMT-CSS6)
(A button type lithium battery installed) (1)
•Station plate (5)
• AN connecting cable (1)
•Component AN Cable (1)
• AC Adaptor (AC-LS5) (1)
• AC Power cord (mains lead) (1)
•Protection cover (1)
•Set of printed documentation
Design and specifications are subject to change
without notice.
-
19-GB

Printed on 70% or more recycled paper using VOC (Volatile
Organic Compound)-free vegetable oil based ink.
Imprimesur papier recycle a70 %ou plus avec de I'encre abase
d'huile vegetale
sans COV (composes organiques volatils).
Impreso en papel reciclado en un 70% 0mas utilizando tinta
hecha con aceite vegetal exento de compuesto organico volatil
(COV).
ffm~~~$~ voc (.V~~*~:7t) ~ti~5m~5m~{£
70% ~.A...tiij~~...tEIUil~o
ffm~T~$~ voc (t¥~~~m~:7t) ~ti~5m~5m.{£
7 0% ~.A...t iij ~~...t EIUil~ 0
http://www.sony.net!
Printed in Japan
IIII1111 ~IIIIIIIII ml
3286877110