Sony CDXM60UI - Marine CD Receiver MP3/WMA/AAC... User manual
SONY
3-274-100-12 (1)
FM/AM
Compact
Disc
Player
CDX-M50IP/CDX-M30
FMIMWII.W
Compact
Disc
Player
CDX-MR50IP
Operating
Instructions
-----Jm.
Mode
d'emploi
..
Manual
de
instrucciones
~
Bedienungsanleitung
a:.
Gebruiksaanwijzing
.-
Istruzioni
per
I'uso
__
Owner's
Record
The model and serial numbers are located
on
the bottom
of
the unit.
Record these numbers
in
the spaces provided below.
Refer
to
these numbers whenever you call upon your Sony dealer regarding this product.
Model
No.
Serial
No.
_
To cancel the demonstration (DEMO) display, see page 16.
Pour annuler la demonstration (DEMO), reportez-vous ala page 16.
Para cance1ar la pantalla de demostraci6n (DEMO), consulte la pagina 16.
Zum
Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte
auf
Seite
14
nacho
Om
de demonstratie (DEMO)
te
annuleren, zie pagina 14.
Per
annullare
1a
dimostrazione (DEMO), vedere pagina 14.
[Q]o§rn
DIGITAL
AUDIO
ITEXT I
IOl
Made for
@j
iPod
©2007 Sony Corporation
SONY
3-274-100-12 (1)
FM/AM
Compact
Disc
Player
CDX-M50IP/CDX-M30
FMIMWII.W
Compact
Disc
Player
CDX-MR50IP
Operating
Instructions
-----Jm.
Mode
d'emploi
..
Manual
de
instrucciones
~
Bedienungsanleitung
a:.
Gebruiksaanwijzing
.-
Istruzioni
per
I'uso
__
Owner's
Record
The model and serial numbers are located
on
the bottom
of
the unit.
Record these numbers
in
the spaces provided below.
Refer
to
these numbers whenever you call upon your Sony dealer regarding this product.
Model
No.
Serial
No.
_
To cancel the demonstration (DEMO) display, see page 16.
Pour annuler la demonstration (DEMO), reportez-vous ala page 16.
Para cance1ar la pantalla de demostraci6n (DEMO), consulte la pagina 16.
Zum
Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte
auf
Seite
14
nacho
Om
de demonstratie (DEMO)
te
annuleren, zie pagina 14.
Per
annullare
1a
dimostrazione (DEMO), vedere pagina 14.
[Q]o§rn
DIGITAL
AUDIO
ITEXT I
IOl
Made for
@j
iPod
©2007 Sony Corporation
•
2
For installation and connections, see the
supplied installation/connections manual.
Warning
CDX-M501P/M30 only
This equipment has been tested and found to
comply with the limits for aClass Bdigital
device, pursuant to Part
15
of
the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and,
if
not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there
is
no guarantee that interference
will not occur in aparticular installation.
If
this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment
off
and on,
the user is encouraged to try to correct the
interference by one
or
more
of
the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
and receiver.
-Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced
radiorrV
technician for help.
You are cautioned that any changes or
modifications not expressly approved
in
this
manual could void your authority to operate this
equipment.
CAUTION
The
use
of
optical instruments with this product
will increase eye hazard.
For the state
of
california,
USA
only
Perchlorate
Material-
special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate
CLASS 1
LASER PRODUCT
This label is located on the bottom
of
the
chassis.
The manufacturer
of
this product
is
Sony
Corporation,
1-7-1
Konan Minato-ku Tokyo,
108-0075 Japan.
The Authorized Representative for EMC and
product safety
is
Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters
please refer to the addresses given in separate
service or guarantee documents.
:a
Disposal
of
Old
Electrical
&
Electronic
Equipment
(Applicable
in
the
European
Union
and
other
•
European
countries
with
separate
collection
systems)
This symbol on the product or on its
packaging indicates that this product shall not be treated
as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling
of
electrical
and electronic equipment. By ensuring this product
is
disposed
of
correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling
of
this product. The recycling
of
materials
will help to conserve natural resources. For more detailed
information about recycling
of
this product, please contact
your local Civic Office, your household waste disposal
service or the shop where you purchased the product.
Applicable accessory: Remote commander
:a
Disposal
of
waste
batteries
(applicable
in
the
European
Union
and
other
European
countries
with
•
separate
collection
systems)
This symbol on the battery or on the packaging indicates
that the battery provided with this product shall not be
treated as household waste. By ensuring these batteries are
disposed
of
correctly, you will help prevent potentially
negative consequences for the environment and human
health which could otherwise be caused by inappropriate
waste handling
of
the battery. The recycling
of
the
materials will help
to
conserve natural resources.
In
case
of
products that for safety, performance or data integrity
reasons require apermanent connection with an
incorporated battery, this battery should be replaced by
qualified service staff only.
To
ensure that the battery will
be treated properly, hand over the product at end-of-life to
the applicable collection point for the recycling
of
electrical and electronic equipment. For all other batteries,
please view the section on how to remove the battery from
the product safely. Hand the battery over to the applicable
collection point for the recycling
of
waste batteries. For
more detailed information about recycling
of
this product
or battery, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product.
•
2
For installation and connections, see the
supplied installation/connections manual.
Warning
CDX-M501P/M30 only
This equipment has been tested and found to
comply with the limits for aClass Bdigital
device, pursuant to Part
15
of
the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and,
if
not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there
is
no guarantee that interference
will not occur in aparticular installation.
If
this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment
off
and on,
the user is encouraged to try to correct the
interference by one
or
more
of
the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
and receiver.
-Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced
radiorrV
technician for help.
You are cautioned that any changes or
modifications not expressly approved
in
this
manual could void your authority to operate this
equipment.
CAUTION
The
use
of
optical instruments with this product
will increase eye hazard.
For the state
of
california,
USA
only
Perchlorate
Material-
special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate
CLASS 1
LASER PRODUCT
This label is located on the bottom
of
the
chassis.
The manufacturer
of
this product
is
Sony
Corporation,
1-7-1
Konan Minato-ku Tokyo,
108-0075 Japan.
The Authorized Representative for EMC and
product safety
is
Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters
please refer to the addresses given in separate
service or guarantee documents.
:a
Disposal
of
Old
Electrical
&
Electronic
Equipment
(Applicable
in
the
European
Union
and
other
•
European
countries
with
separate
collection
systems)
This symbol on the product or on its
packaging indicates that this product shall not be treated
as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling
of
electrical
and electronic equipment. By ensuring this product
is
disposed
of
correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling
of
this product. The recycling
of
materials
will help to conserve natural resources. For more detailed
information about recycling
of
this product, please contact
your local Civic Office, your household waste disposal
service or the shop where you purchased the product.
Applicable accessory: Remote commander
:a
Disposal
of
waste
batteries
(applicable
in
the
European
Union
and
other
European
countries
with
•
separate
collection
systems)
This symbol on the battery or on the packaging indicates
that the battery provided with this product shall not be
treated as household waste. By ensuring these batteries are
disposed
of
correctly, you will help prevent potentially
negative consequences for the environment and human
health which could otherwise be caused by inappropriate
waste handling
of
the battery. The recycling
of
the
materials will help
to
conserve natural resources.
In
case
of
products that for safety, performance or data integrity
reasons require apermanent connection with an
incorporated battery, this battery should be replaced by
qualified service staff only.
To
ensure that the battery will
be treated properly, hand over the product at end-of-life to
the applicable collection point for the recycling
of
electrical and electronic equipment. For all other batteries,
please view the section on how to remove the battery from
the product safely. Hand the battery over to the applicable
collection point for the recycling
of
waste batteries. For
more detailed information about recycling
of
this product
or battery, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product.
-wP
_la"":"'
Y
S_--1
_.
Windows
1M
Media™
Microsoft, Windows Media,
and the Windows logo are
trademarks or registered
trademarks
of
Microsoft
Corporation in the United States and/or other
countries.
CDX-M50IP/MR50IP only
iPod is atrademark
of
Apple Inc., registered in
the U.S. and other countries.
CDX-M50IPIM30 only
H3'
Radio®
-!JREADY
The
"HD
Radio Ready" logo indicates that this
product will control aSony HD
Radio™
tuner
(sold separately).
For
HD
Radio™
tuner operation, please refer to
the HD
Radio™
tuner
owner's
manual.
The HD Radio Ready logo is aregistered
trademark
of
iBiquity.
HD
Radio™
is atrademark
of
iBiquity Digital
Corp.
CDX-M501P/M30 only
nThe
"SAT
Radio Ready"
~SA
1"
logo indicates that this
~RADIO
product will control asatellite
REA
0 Y radio tuner module (sold
separately). Please see your nearest authorized
Sony dealer for details on the satellite radio
tuner module.
"SAT
Radio," "SAT Radio Ready," the SAT
Radio and SAT Radio Ready logos and all
related marks are trademarks
of
Sirius Satellite
Radio Inc. and XM Satellite Radio Inc.
Warning if your boat's ignition has no
ACC position
Be sure to set the Auto Offfunction (page 16).
The unit will shut offcompletely and
automatically in the set time after the unit is
turned off, which prevents battery drain.
If
you do not set the Auto Offfunction, press
and hold
(OFF)
until the display disappears
each time you turn the ignition off.
•
3
-wP
_la"":"'
Y
S_--1
_.
Windows
1M
Media™
Microsoft, Windows Media,
and the Windows logo are
trademarks or registered
trademarks
of
Microsoft
Corporation in the United States and/or other
countries.
CDX-M50IP/MR50IP only
iPod is atrademark
of
Apple Inc., registered in
the U.S. and other countries.
CDX-M50IPIM30 only
H3'
Radio®
-!JREADY
The
"HD
Radio Ready" logo indicates that this
product will control aSony HD
Radio™
tuner
(sold separately).
For
HD
Radio™
tuner operation, please refer to
the HD
Radio™
tuner
owner's
manual.
The HD Radio Ready logo is aregistered
trademark
of
iBiquity.
HD
Radio™
is atrademark
of
iBiquity Digital
Corp.
CDX-M501P/M30 only
nThe
"SAT
Radio Ready"
~SA
1"
logo indicates that this
~RADIO
product will control asatellite
REA
0 Y radio tuner module (sold
separately). Please see your nearest authorized
Sony dealer for details on the satellite radio
tuner module.
"SAT
Radio," "SAT Radio Ready," the SAT
Radio and SAT Radio Ready logos and all
related marks are trademarks
of
Sirius Satellite
Radio Inc. and XM Satellite Radio Inc.
Warning if your boat's ignition has no
ACC position
Be sure to set the Auto Offfunction (page 16).
The unit will shut offcompletely and
automatically in the set time after the unit is
turned off, which prevents battery drain.
If
you do not set the Auto Offfunction, press
and hold
(OFF)
until the display disappears
each time you turn the ignition off.
•
3
•
4
•
4
Table
of
Contents
'
Welcome!
6
Getting Started
Resetting the unit 6
Preparing the card remote commander 6
Setting the clock 6
Detaching the front panel 7
Attaching the front panel 7
Inserting the disc in the unit 7
Ejecting the disc 7
Location of controls and basic
operations
Main unit 8
Card remote commander RM-X
151
10
CD
Display items
11
Repeat and shuffle play
11
Radio
Storing and receiving stations
11
Storing automatically -BTM
11
Storing manually
11
Receiving the stored stations
11
Tuning automatically 12
RDS (CDX-MR50IP) 12
Overview
12
Setting
AF
and TA . . . . . . . . . . . . . . . . . . .
12
Selecting PTY
13
Setting
CT
..........................
13
iPod (CDX-M501P/MR50IP)
Playing back iPod 14
Playing tracks 14
Display items 14
Setting the play
mode.
................
..
14
Selecting Album, Artist or Playlist 14
Repeat and shuffle Play
15
Scan
15
Other functions
Changing the sound settings. ...........
..
15
Adjusting the sound characteristics. . . .
..
15
Customizing the equalizer curve
-EQ3
16 •
Adjusting setup items -
SET
16
Using optional equipment.
17
Auxiliary audio equipment. . . . . . . . . . .
..
17
CD/MD
changer. ..................
..
18
Marine remote commander
RM-X55MIXIIM
18
Additional Information
Precautions .........................
..
19
Notes on discs
...
.................
..
19
Playback order
of
MP3IWMA/AAC
files 20
About MP3 files. .................... 20
About
WMA
files 20
About AAC files 20
About iPod (CDX-M50IPIMR50IP) 20
Maintenance 20
Removing the unit.
21
Specifications 22
Troubleshooting 23
Error displayslMessages 24
5
Table
of
Contents
'
Welcome!
6
Getting Started
Resetting the unit 6
Preparing the card remote commander 6
Setting the clock 6
Detaching the front panel 7
Attaching the front panel 7
Inserting the disc in the unit 7
Ejecting the disc 7
Location of controls and basic
operations
Main unit 8
Card remote commander RM-X
151
10
CD
Display items
11
Repeat and shuffle play
11
Radio
Storing and receiving stations
11
Storing automatically -BTM
11
Storing manually
11
Receiving the stored stations
11
Tuning automatically 12
RDS (CDX-MR50IP) 12
Overview
12
Setting
AF
and TA . . . . . . . . . . . . . . . . . . .
12
Selecting PTY
13
Setting
CT
..........................
13
iPod (CDX-M501P/MR50IP)
Playing back iPod 14
Playing tracks 14
Display items 14
Setting the play
mode.
................
..
14
Selecting Album, Artist or Playlist 14
Repeat and shuffle Play
15
Scan
15
Other functions
Changing the sound settings. ...........
..
15
Adjusting the sound characteristics. . . .
..
15
Customizing the equalizer curve
-EQ3
16 •
Adjusting setup items -
SET
16
Using optional equipment.
17
Auxiliary audio equipment. . . . . . . . . . .
..
17
CD/MD
changer. ..................
..
18
Marine remote commander
RM-X55MIXIIM
18
Additional Information
Precautions .........................
..
19
Notes on discs
...
.................
..
19
Playback order
of
MP3IWMA/AAC
files 20
About MP3 files. .................... 20
About
WMA
files 20
About AAC files 20
About iPod (CDX-M50IPIMR50IP) 20
Maintenance 20
Removing the unit.
21
Specifications 22
Troubleshooting 23
Error displayslMessages 24
5
Note
Pressing the RESETbutton will erase the clocksetting
and
some storedcontents.
Preparing
the
card
remote
commander
Getting
Started
Resetting
the
unit
Before operating the unit for the first time, or
after replacing the boat's battery or changing the
connections, you must reset the unit.
Detach the front panel and press the RESET
button with apointed object, such as aball-point
pen.
oil
RESET
~
~
button
~
Welcome!
Thank you for purchasing this Sony Compact
Disc Player.
You
can enjoy your boating with the
following functions.
•CD playback
You
can play CD-DA (also containing CD
TEXT) and CD-R/CD-RW (MP3/WMA/AAC
files (page 20)).
Type of discs Label
on
the disc
CD-DA
[[]D~~
ffi]D~@
DIGITAL
AUDIO
DIGITAL
AUDIO
la·,MII IReWritablel
[[]D~~
[[]OO~~
MP3
DIGITAL
AUDIO
DIGITAL
AUDIO
WMA
GM·,M'MI
IReWritablel
AAC
ffi]D~~
ffi]o~~
IiM·I
••
mml
IReWritablel
•
6
•Radio reception
-
You
can store up to 6stations per band.
CDX-M501P/M30:
FMI,
FM2, FM3,
AMI
and AM2
CDX-MR50IP:
FMI,
FM2, FM3,
MWand
LW
-
8TM
(Best Tuning Memory): The unit selects
strong signal stations and stores them.
•RDS services
-
You
can listen to FM stations with the Radio
Data System (RDS) in Europe.
(CDX-MR50IP)
•Sound adjustment
-EQ3 stage2:
You
can choose
anyone
of
7
preset equalizer curves.
-DSO (Dynamic Soundstage Organizer):
Creates amore ambient sound field, using
virtual speaker synthesis, to enhance the
sound
of
speakers, even
if
they are installed
low in the door.
•Optional device operation
Various kinds
of
audio devices can be
connected.
-iPod: iPod connection can be made by the
dock connector cable on the rear
of
the unit.
(CDX-M50IPIMR50IP)
-Portable audio device: An AUX input
jack
on the front
of
the unit allows connection
of
aportable audio device (analog
connection).
-CD/MD changers:
CDIMD
changers can be
connected to the Sony BUS at the rear
of
the
unit.
Before using the card remote commander for the
first time, remove the insulation film.
Tip
For
how
to replace the battery, see "Replacing the
lithium battery
of
the card remote commander"on
page 20.
Setting
the
clock
CDX-M501P/M30:
I2-hour indication
CDX-MR50IP:
24-hour indication
1Press and hold the select button.
The setup display appears.
2Press the select button repeatedly
until "CLOCK-ADJ" appears.
3Press
(SEEK)
+.
The hour indication flashes.
4Rotate the volume control dial to set
the hour and minute.
To
move the digital indication, press
(SEEK)
-/+.
5Press the select button.
The setup is complete and the clock starts.
Note
Pressing the RESETbutton will erase the clocksetting
and
some storedcontents.
Preparing
the
card
remote
commander
Getting
Started
Resetting
the
unit
Before operating the unit for the first time, or
after replacing the boat's battery or changing the
connections, you must reset the unit.
Detach the front panel and press the RESET
button with apointed object, such as aball-point
pen.
oil
RESET
~
~
button
~
Welcome!
Thank you for purchasing this Sony Compact
Disc Player.
You
can enjoy your boating with the
following functions.
•CD playback
You
can play CD-DA (also containing CD
TEXT) and CD-R/CD-RW (MP3/WMA/AAC
files (page 20)).
Type of discs Label
on
the disc
CD-DA
[[]D~~
ffi]D~@
DIGITAL
AUDIO
DIGITAL
AUDIO
la·,MII IReWritablel
[[]D~~
[[]OO~~
MP3
DIGITAL
AUDIO
DIGITAL
AUDIO
WMA
GM·,M'MI
IReWritablel
AAC
ffi]D~~
ffi]o~~
IiM·I
••
mml
IReWritablel
•
6
•Radio reception
-
You
can store up to 6stations per band.
CDX-M501P/M30:
FMI,
FM2, FM3,
AMI
and AM2
CDX-MR50IP:
FMI,
FM2, FM3,
MWand
LW
-
8TM
(Best Tuning Memory): The unit selects
strong signal stations and stores them.
•RDS services
-
You
can listen to FM stations with the Radio
Data System (RDS) in Europe.
(CDX-MR50IP)
•Sound adjustment
-EQ3 stage2:
You
can choose
anyone
of
7
preset equalizer curves.
-DSO (Dynamic Soundstage Organizer):
Creates amore ambient sound field, using
virtual speaker synthesis, to enhance the
sound
of
speakers, even
if
they are installed
low in the door.
•Optional device operation
Various kinds
of
audio devices can be
connected.
-iPod: iPod connection can be made by the
dock connector cable on the rear
of
the unit.
(CDX-M50IPIMR50IP)
-Portable audio device: An AUX input
jack
on the front
of
the unit allows connection
of
aportable audio device (analog
connection).
-CD/MD changers:
CDIMD
changers can be
connected to the Sony BUS at the rear
of
the
unit.
Before using the card remote commander for the
first time, remove the insulation film.
Tip
For
how
to replace the battery, see "Replacing the
lithium battery
of
the card remote commander"on
page 20.
Setting
the
clock
CDX-M501P/M30:
I2-hour indication
CDX-MR50IP:
24-hour indication
1Press and hold the select button.
The setup display appears.
2Press the select button repeatedly
until "CLOCK-ADJ" appears.
3Press
(SEEK)
+.
The hour indication flashes.
4Rotate the volume control dial to set
the hour and minute.
To
move the digital indication, press
(SEEK)
-/+.
5Press the select button.
The setup is complete and the clock starts.
To display the clock, press
(DSPL).
Press
(
DSPL)
again to return to the previous display.
Tip
You
can set the clock automatically with the RDS
feature (page 13). (CDX-MR50IP)
Detaching
the
front
panel
You can detach the front panel
of
this unit to
prevent theft.
Caution alarm
If
you
tum
the ignition switch to the OFF
position without detaching the front panel, the
caution alarm will sound for afew seconds.
The alarm will only sound
if
the built-in
amplifier is used.
1Press
(OFF).
The unit is turned off.
2Press
(OPEN).
The front panel
is
flipped down.
3Slide the front panel to the right, then
gently pull out the left end of the front
panel.
Notes
•Do not drop
or
put
excessive pressure on the front
panel
and
display window.
•Do not subject the front panel to heat/high
temperature
or
moisture. Avoid leaving it in a
moored boat.
Attaching the front panel
Place the hole ®
of
the front panel onto the
spindle ®on the unit, then lightly push the left
side in.
Press
(SOURCE)
on the unit (or insert adisc) to
operate the unit.
Note
Do
not
put
anything on the innersurface
of
the front
panel.
Inserting
the
disc
in
the
unit
1Press
(OPEN).
2Insert the disc (label side up).
3Close the front panel.
Playback starts automatically.
Ejecting the disc
1Press
(OPEN
).
2
Press~.
The disc is ejected.
3Close the front panel.
•
7
To display the clock, press
(DSPL).
Press
(
DSPL)
again to return to the previous display.
Tip
You
can set the clock automatically with the RDS
feature (page 13). (CDX-MR50IP)
Detaching
the
front
panel
You can detach the front panel
of
this unit to
prevent theft.
Caution alarm
If
you
tum
the ignition switch to the OFF
position without detaching the front panel, the
caution alarm will sound for afew seconds.
The alarm will only sound
if
the built-in
amplifier is used.
1Press
(OFF).
The unit is turned off.
2Press
(OPEN).
The front panel
is
flipped down.
3Slide the front panel to the right, then
gently pull out the left end of the front
panel.
Notes
•Do not drop
or
put
excessive pressure on the front
panel
and
display window.
•Do not subject the front panel to heat/high
temperature
or
moisture. Avoid leaving it in a
moored boat.
Attaching the front panel
Place the hole ®
of
the front panel onto the
spindle ®on the unit, then lightly push the left
side in.
Press
(SOURCE)
on the unit (or insert adisc) to
operate the unit.
Note
Do
not
put
anything on the innersurface
of
the front
panel.
Inserting
the
disc
in
the
unit
1Press
(OPEN).
2Insert the disc (label side up).
3Close the front panel.
Playback starts automatically.
Ejecting the disc
1Press
(OPEN
).
2
Press~.
The disc is ejected.
3Close the front panel.
•
7
Front panel removedFront panel removed
This section contains instructions on the location
of
controls and basic operations. For details, see
the respective pages.
For iPod operation, see
"iPod
(CDX-M50IP/
MR50IP)" on page 14, or for optional device
(CD/MD changer, etc.,) operation, see "Using
optional equipment" on page 17.
The corresponding buttons on the card remote
commander control the same functions as those
on the unit.
[I]
OFF
button
To
power off; stop the source.
[2] Volume
control
dial/select
button
page 15
To
adjust volume (rotate); select setup items
(press and rotate).
~
SOURCE
button
To power on; change the source (Radio/CD/
AUXlPD*1)*2.
@]
Display
window
[ID
AUX
input
jack
page 17
To connect aportable audio device.
[§]
OPEN
button
page 7
[1]
ALBM
+/-
buttons
(during
MP3IWMN
AAC
playback)
To skip albums (press); skip albums
continuously (press and hold).
lID
Receptor
for
the
card
remote
commander
[ill SEEK
-/+
buttons
CDIPD*1:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1second and hold); reverse/fast-
forward atrack (press and hold).
Radio:
To tune in stations automatically (press); find
astation manually (press and hold).
11m
MODE
button
page
11
To
select the radio band*2; select the play
mode
of
iPod*1.
Ill] BTM/CAT
button
(CDX-M50IP/M30)
page
11
To start the
BTM
function (press and hold).
AF
(Alternative
Frequencies)/TA
(Traffic
Announcement)/PTY
(Program
Type)
button
(CDX-MR50IP)
page 12
To
set
AF
and TA (press); select PTY (press
and hold) in RDS.
[12J
Frequency
select
switch
(CDX-M50IP/
M30
only)
(located on the bottom
of
the unit)
See "Frequency select switch" in the
supplied installation/connections manual.
~
Number
buttons
CDIPD*1:
®:
REP page
11
0:
SHUF page
11
®:
PAUSE
To
pause playback
of
a
CD
on this unit.
To
cancel, press again.
Radio:
To
receive stored stations (press); store
stations (press and hold).
IHl
DSPL (display)/SCRL
(scroll)
button
page
11
To
change display items (press); scroll the
display item (press and hold).
[1§]
RESET
button
page 6
[WI
~
(eject)
button
page 7
To
eject the disc.
I11J
Disc
slot
page 7
To
insert the disc.
continue
to
next
page
---+
This section contains instructions on the location
of
controls and basic operations. For details, see
the respective pages.
For iPod operation, see
"iPod
(CDX-M50IP/
MR50IP)" on page 14, or for optional device
(CD/MD changer, etc.,) operation, see "Using
optional equipment" on page 17.
The corresponding buttons on the card remote
commander control the same functions as those
on the unit.
[I]
OFF
button
To
power off; stop the source.
[2] Volume
control
dial/select
button
page 15
To
adjust volume (rotate); select setup items
(press and rotate).
~
SOURCE
button
To power on; change the source (Radio/CD/
AUXlPD*1)*2.
@]
Display
window
[ID
AUX
input
jack
page 17
To connect aportable audio device.
[§]
OPEN
button
page 7
[1]
ALBM
+/-
buttons
(during
MP3IWMN
AAC
playback)
To skip albums (press); skip albums
continuously (press and hold).
lID
Receptor
for
the
card
remote
commander
[ill SEEK
-/+
buttons
CDIPD*1:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1second and hold); reverse/fast-
forward atrack (press and hold).
Radio:
To tune in stations automatically (press); find
astation manually (press and hold).
11m
MODE
button
page
11
To
select the radio band*2; select the play
mode
of
iPod*1.
Ill] BTM/CAT
button
(CDX-M50IP/M30)
page
11
To start the
BTM
function (press and hold).
AF
(Alternative
Frequencies)/TA
(Traffic
Announcement)/PTY
(Program
Type)
button
(CDX-MR50IP)
page 12
To
set
AF
and TA (press); select PTY (press
and hold) in RDS.
[12J
Frequency
select
switch
(CDX-M50IP/
M30
only)
(located on the bottom
of
the unit)
See "Frequency select switch" in the
supplied installation/connections manual.
~
Number
buttons
CDIPD*1:
®:
REP page
11
0:
SHUF page
11
®:
PAUSE
To
pause playback
of
a
CD
on this unit.
To
cancel, press again.
Radio:
To
receive stored stations (press); store
stations (press and hold).
IHl
DSPL (display)/SCRL
(scroll)
button
page
11
To
change display items (press); scroll the
display item (press and hold).
[1§]
RESET
button
page 6
[WI
~
(eject)
button
page 7
To
eject the disc.
I11J
Disc
slot
page 7
To
insert the disc.
continue
to
next
page
---+
PI
t
(+)1.
(-)
buttons
To
control CD/PD*1, the same as
(ALBM)
+/-
on the unit.
Setup, sound setting, etc., can be operated by
t•.
f)I
SeRl
(scroll) button
To
scroll the display item.
~
Number buttons
To
receive stored stations (press); store
stations (press and hold).
*1COX-M50IPIMR50IP only
*2 In the case
of
aCOIMO changer,
HO
radio tuner
or
SATtunerbeing connected; when
(SOURCE)
is
pressed, the connecteddevice ("MO:' "HO:'
'XM"
or
"SR") will appear
in
the display, depending
on
which device is connected. Furthermore,
if
(
MODE)
is pressed, you can switch the changer,
HO
radio tuner band
or
SAT tuner band.
(A
HO
radio tuner
or
SATtuner can only
be
connected
to
the COX-M50IPIM30.)
Note
Ifthe unit
is
turned
off
and
the display disappears, it
cannot be operated with the cardremote commander
unless
(SOURCE)
on the unit is pressed,
or
adisc
is
inserted
to
activate the unit first.
About
AUX
cap
When not using the AUX inputjack (rnJ), use the
supplied
AUX
cap to prevent water entering. Keep the
AUX
cap out
of
the reach
of
children
to
prevent
accidental swallowing.
It---+---
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 6).
1m
~
(~)/
..
(~)
buttons
To
control CD/radio/PD*1, the same as
(SEEK)
-/+
on the unit.
Setup, sound setting, etc., can be operated by
~
...
1m
DSPl
(display) button
To
change display items.
PI
VOL (volume)
+/-
button
To
adjust volume.
mATT
(attenuate) button
To
attenuate the sound.
To
cancel, press
again.
SEl
(select) button
The same as the select button on the unit.
Card remote commander
RM-X151
PI
t
(+)1.
(-)
buttons
To
control CD/PD*1, the same as
(ALBM)
+/-
on the unit.
Setup, sound setting, etc., can be operated by
t•.
f)I
SeRl
(scroll) button
To
scroll the display item.
~
Number buttons
To
receive stored stations (press); store
stations (press and hold).
*1COX-M50IPIMR50IP only
*2 In the case
of
aCOIMO changer,
HO
radio tuner
or
SATtunerbeing connected; when
(SOURCE)
is
pressed, the connecteddevice ("MO:' "HO:'
'XM"
or
"SR") will appear
in
the display, depending
on
which device is connected. Furthermore,
if
(
MODE)
is pressed, you can switch the changer,
HO
radio tuner band
or
SAT tuner band.
(A
HO
radio tuner
or
SATtuner can only
be
connected
to
the COX-M50IPIM30.)
Note
Ifthe unit
is
turned
off
and
the display disappears, it
cannot be operated with the cardremote commander
unless
(SOURCE)
on the unit is pressed,
or
adisc
is
inserted
to
activate the unit first.
About
AUX
cap
When not using the AUX inputjack (rnJ), use the
supplied
AUX
cap to prevent water entering. Keep the
AUX
cap out
of
the reach
of
children
to
prevent
accidental swallowing.
It---+---
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 6).
1m
~
(~)/
..
(~)
buttons
To
control CD/radio/PD*1, the same as
(SEEK)
-/+
on the unit.
Setup, sound setting, etc., can be operated by
~
...
1m
DSPl
(display) button
To
change display items.
PI
VOL (volume)
+/-
button
To
adjust volume.
mATT
(attenuate) button
To
attenuate the sound.
To
cancel, press
again.
SEl
(select) button
The same as the select button on the unit.
Card remote commander
RM-X151
For details on selecting a
CDIMD
changer, see
page 18.
Radio
Storing
and
receiving
stations
Display
items
Caution
When tuning in stations while boating, use Best
Tuning Memory (BTM) to prevent an accident.
*When
an
MP3IWMAlAAC is played.
To
return to normal play mode,
select"
c::
OFF"
or "SHUF
OFE"
Repeat and
shuffle
play
1
During
playback,
press
®(REP)
or
CD
(SHUF) repeatedly
until
the
desired
setting
appears.
oSource
eTrack number/Elapsed playing time, DiscI
artist name, Album number*, Album name,
Track name, Text information, Clock
*Album
number
is displayed only when the album is
changed.
To
change display items
e,
press
(DSPL).
Tip
Displayed items will differ, depending on the disc type,
recording format
and
settings. For details on MP31
WMAlAAC, see
page
20.
•
Storing
manually
1While
receiving
the
station
that
you
want
to
store,
press
and
hold
a
number
button
(CD
to
®)
until
"MEM"
appears.
Note
If
you
try
to store
another
station on the same
number
button, the previously storedstation will be replaced.
Tip
When aRDB station is stored, the AFITA setting is
also stored (page 12). (CDX-MR50IP only)
Receiving
the
stored
stations
1Select
the
band,
then
press
a
number
button
(CD
to
®).
Storing
by
the BTM
button
(CDX-M50IPIM30 only)
Press and hold
(BTM
)until "BTM" flashes,
instead
of
steps 2to 4.
Storing
automatically
-
BTM
1Press
(SOURCE)
repeatedly
until
"TUNER" appears.
To change the band, press
(MODE)
repeatedly.
2Press
and
hold
the
select
button.
The setup display appears.
3Press
the
select
button
repeatedly
until
"BTM"
appears.
4Press
(SEEK)
+.
The unit stores stations in order
of
frequency
on the number buttons.
Abeep sounds when the setting is stored.
track repeatedly.
album in random order.
disc in random order.
album repeatedly.
To
play
~
===
I
1)
~~~~~
usn
E03
c::
ALBUM*
c::
TRACK
SHUF
ALBUM*
SHUF DISC
Select
11
For details on selecting a
CDIMD
changer, see
page 18.
Radio
Storing
and
receiving
stations
Display
items
Caution
When tuning in stations while boating, use Best
Tuning Memory (BTM) to prevent an accident.
*When
an
MP3IWMAlAAC is played.
To
return to normal play mode,
select"
c::
OFF"
or "SHUF
OFE"
Repeat and
shuffle
play
1
During
playback,
press
®(REP)
or
CD
(SHUF) repeatedly
until
the
desired
setting
appears.
oSource
eTrack number/Elapsed playing time, DiscI
artist name, Album number*, Album name,
Track name, Text information, Clock
*Album
number
is displayed only when the album is
changed.
To
change display items
e,
press
(DSPL).
Tip
Displayed items will differ, depending on the disc type,
recording format
and
settings. For details on MP31
WMAlAAC, see
page
20.
•
Storing
manually
1While
receiving
the
station
that
you
want
to
store,
press
and
hold
a
number
button
(CD
to
®)
until
"MEM"
appears.
Note
If
you
try
to store
another
station on the same
number
button, the previously storedstation will be replaced.
Tip
When aRDB station is stored, the AFITA setting is
also stored (page 12). (CDX-MR50IP only)
Receiving
the
stored
stations
1Select
the
band,
then
press
a
number
button
(CD
to
®).
Storing
by
the BTM
button
(CDX-M50IPIM30 only)
Press and hold
(BTM
)until "BTM" flashes,
instead
of
steps 2to 4.
Storing
automatically
-
BTM
1Press
(SOURCE)
repeatedly
until
"TUNER" appears.
To change the band, press
(MODE)
repeatedly.
2Press
and
hold
the
select
button.
The setup display appears.
3Press
the
select
button
repeatedly
until
"BTM"
appears.
4Press
(SEEK)
+.
The unit stores stations in order
of
frequency
on the number buttons.
Abeep sounds when the setting is stored.
track repeatedly.
album in random order.
disc in random order.
album repeatedly.
To
play
~
===
I
1)
~~~~~
usn
E03
c::
ALBUM*
c::
TRACK
SHUF
ALBUM*
SHUF DISC
Select
11
I
12
Tuning automatically
1Select the band, then press
(SEEK)
-/+
to search for the station.
Scanning stops when the unit receives a
station. Repeat this procedure until the
desired station is received.
Tip
If
you know the frequency
of
the station you want to
listen
to,
press
and
hold
(
SEEK)
-/+
to locate the
approximate frequency, then press
(SEEK)
-/+
repeatedly to fine adjust to the desired frequency
(manual tuning).
RDS
(CDX-MR50IP)
Overview
FM stations with Radio Data System (RDS)
service send inaudible digital information along
with the regular radio program signal.
Display items
---r
---
DSD
oRadio band, Function
o
TAfTP*l
eFrequency*2 (Program service name), Preset
number, Clock, RDS data
*1'TA" flashes during traffic information. "TP" lights
up while such astation is received.
*2 While receiving the
RDS
station,
"*"
is displayed
on the left
of
the frequency indication.
To
change display items
e,
press
(DSPL).
RDS services
This unit automatically provides RDS services as
follows:
AF
(Alternative Frequencies)
Selects and retunes the station with the
strongest signal in anetwork. By using this
function, you can continuously listen to the
same program during along-distance voyage
without having to retune the same station
manually.
TA
(Traffic Announcement)ITP (Traffic
Program)
Provides current traffic information/programs.
Any information/program received, will
interrupt the currently selected source.
PTY (Program Types)
Displays the currently received program type.
Also searches your selected program type.
CT
(Clock Time)
The
CT
data from the RDS transmission sets
the clock.
Notes
•Depending on the countrylregion,
not
all RDS
functions
may
be
available.
•RDS will not work
if
the signal strength is too weak,
or
if
the station you are tuned to is not transmitting
RDSdata.
Setting AF and TA
1Press
(AFrrA)
repeatedly until the
desired setting appears.
Select
To
AF-ON
activate AF and deactivate
TA.
TA-ON
activate
TA
and deactivate
AF.
AF,
TA-ON
activate both AF and TA.
AF,
TA-OFF
deactivate both AF and TA.
Storing RDS stations with the AF and
TA
setting
You
can preset RDS stations along with the AF/
TA
setting.
If
you use the BTM function, only
RDS stations are stored with the same
AFfTA
setting.
If
you preset manually, you can preset both RDS
and non-RDS stations with the AFfTA setting for
each.
1Set AF/TA, then store the station with BTM or
manually.
I
12
Tuning automatically
1Select the band, then press
(SEEK)
-/+
to search for the station.
Scanning stops when the unit receives a
station. Repeat this procedure until the
desired station is received.
Tip
If
you know the frequency
of
the station you want to
listen
to,
press
and
hold
(
SEEK)
-/+
to locate the
approximate frequency, then press
(SEEK)
-/+
repeatedly to fine adjust to the desired frequency
(manual tuning).
RDS
(CDX-MR50IP)
Overview
FM stations with Radio Data System (RDS)
service send inaudible digital information along
with the regular radio program signal.
Display items
---r
---
DSD
oRadio band, Function
o
TAfTP*l
eFrequency*2 (Program service name), Preset
number, Clock, RDS data
*1'TA" flashes during traffic information. "TP" lights
up while such astation is received.
*2 While receiving the
RDS
station,
"*"
is displayed
on the left
of
the frequency indication.
To
change display items
e,
press
(DSPL).
RDS services
This unit automatically provides RDS services as
follows:
AF
(Alternative Frequencies)
Selects and retunes the station with the
strongest signal in anetwork. By using this
function, you can continuously listen to the
same program during along-distance voyage
without having to retune the same station
manually.
TA
(Traffic Announcement)ITP (Traffic
Program)
Provides current traffic information/programs.
Any information/program received, will
interrupt the currently selected source.
PTY (Program Types)
Displays the currently received program type.
Also searches your selected program type.
CT
(Clock Time)
The
CT
data from the RDS transmission sets
the clock.
Notes
•Depending on the countryiregion,
not
all RDS
functions
may
be
available.
•RDS will not work
if
the signal strength is too weak,
or
if
the station you are tuned to is not transmitting
RDSdata.
Setting AF and TA
1Press
(AFrrA)
repeatedly until the
desired setting appears.
Select
To
AF-ON
activate AF and deactivate
TA.
TA-ON
activate
TA
and deactivate
AF.
AF,
TA-ON
activate both AF and TA.
AF,
TA-OFF
deactivate both AF and TA.
Storing RDS stations with the AF and
TA
setting
You
can preset RDS stations along with the AF/
TA
setting.
If
you use the BTM function, only
RDS stations are stored with the same
AFfTA
setting.
If
you preset manually, you can preset both RDS
and non-RDS stations with the AFfTA setting for
each.
1Set AF/TA, then store the station with BTM or
manually.
Receiving emergency
announcements
With
AF
or
TA
on, the emergency
announcements will automatically interrupt the
currently selected source.
Tip
If
you adjust the volume level during atraffic
announcement, that level will
be
stored into
memory
for subsequent traffic announcements, independently
from the regular volume level.
Staying with one regional program
-REG
When the AF function is on: this unit's factory
setting restricts reception to aspecific region, so
you will not be switched to another regional
station with astronger frequency.
If
you leave this regional program's reception
area, set "REG-OFF" in setup during FM
reception (page 17).
Note
This function does
not
work in the
UK
and
in some
otherareas.
Local Link function (UK only)
This function enables you to select other local
stations in the area, even
if
they are not stored on
your number buttons.
1During FM reception, press anumber button
(CD
to
CD)
on which alocal station is stored.
2Within 5seconds, press again anumber button
of
the local station.
Repeat this procedure until the local station is
received.
Selecting
PTV
1Press and hold
(AF/TA)
(PTY) during
FM
reception.
Type of programs
NEWS (News), AFFAIRS (Current Affairs),
INFO (Information), SPORT (Sports),
EDUCATE (Education), DRAMA (Drama),
CULTURE (Culture), SCIENCE (Science),
VARIED (Varied), POP M(Popular Music),
ROCK M(Rock Music), EASY M(Easy
Listening), LIGHT M(Light Classical),
CLASSICS (Classical), OTHER M(Other
Music Type), WEATHER (Weather),
FINANCE (Finance), CHILDREN (Children's
Programs), SOCIAL A(Social Affairs),
RELIGION (Religion), PHONE
IN
(Phone In),
TRAVEL (Travel), LEISURE (Leisure), JAZZ
(Jazz Music), COUNTRY (Country Music), .
NATION M(National Music), OLDIES (OldIes
Music), FOLK M(Folk Music), DOCUMENT
(Documentary)
Nore •
You
cannot use this function in countries/regions
where
no
PTY
data is available.
Setting
CT
1Set "CT-ON"
in
setup (page 16).
Notes
•The
CT
function may
not
work even though an ROS
station is being received.
•There mightbe adifference between the time
set
by
the
CT
function
and
the actual time.
PT'::I
===r
---
OBO
]
::::::
........
M
..
E03
The
current program type name appears
if
the
station is transmitting PTY data.
2Press
(AF/TA)
(PTY) repeatedly until
the desired program type appears.
3Press
(SEEK)
-/+.
The
unit starts to search for astation
broadcasting the selected program type.
13
Receiving emergency
announcements
With
AF
or
TA
on, the emergency
announcements will automatically interrupt the
currently selected source.
Tip
If
you adjust the volume level during atraffic
announcement, that level will
be
stored into
memory
for subsequent traffic announcements, independently
from the regular volume level.
Staying with one regional program
-REG
When the AF function is on: this unit's factory
setting restricts reception to aspecific region, so
you will not be switched to another regional
station with astronger frequency.
If
you leave this regional program's reception
area, set "REG-OFF" in setup during FM
reception (page 17).
Note
This function does
not
work in the
UK
and
in some
otherareas.
Local Link function (UK only)
This function enables you to select other local
stations in the area, even
if
they are not stored on
your number buttons.
1During FM reception, press anumber button
(CD
to
CD)
on which alocal station is stored.
2Within 5seconds, press again anumber button
of
the local station.
Repeat this procedure until the local station is
received.
Selecting
PTV
1Press and hold
(AF/TA)
(PTY) during
FM
reception.
Type of programs
NEWS (News), AFFAIRS (Current Affairs),
INFO (Information), SPORT (Sports),
EDUCATE (Education), DRAMA (Drama),
CULTURE (Culture), SCIENCE (Science),
VARIED (Varied), POP M(Popular Music),
ROCK M(Rock Music), EASY M(Easy
Listening), LIGHT M(Light Classical),
CLASSICS (Classical), OTHER M(Other
Music Type), WEATHER (Weather),
FINANCE (Finance), CHILDREN (Children's
Programs), SOCIAL A(Social Affairs),
RELIGION (Religion), PHONE
IN
(Phone In),
TRAVEL (Travel), LEISURE (Leisure), JAZZ
(Jazz Music), COUNTRY (Country Music), .
NATION M(National Music), OLDIES (OldIes
Music), FOLK M(Folk Music), DOCUMENT
(Documentary)
Nore •
You
cannot use this function in countries/regions
where
no
PTY
data is available.
Setting
CT
1Set "CT-ON"
in
setup (page 16).
Notes
•The
CT
function may
not
work even though an ROS
station is being received.
•There mightbe adifference between the time
set
by
the
CT
function
and
the actual time.
PT'::I
===r
---
OBO
]
::::::
........
M
..
E03
The
current program type name appears
if
the
station is transmitting PTY data.
2Press
(AF/TA)
(PTY) repeatedly until
the desired program type appears.
3Press
(SEEK)
-/+.
The
unit starts to search for astation
broadcasting the selected program type.
13
Display items
Setting
the
play
mode
I
1
······
E03
I
To change display items, press
(DSPL).
Note
Some
letters stored in iPod
may
not
be
displayed
correctly
Selecting Album, Artist or Playlist
1During playback, press
(MODE).
The mode changes as follows:
ALBUM
-+
ARTIST
-+
PLAYLIST
Skipping albums, artists and
play
lists
I
Track/album/artist name, Track number,
Elapsed playing time, Clock
Tips
•When the iPod is connected to the dock connector,
the
mode
changes to the Resuming mode. In
Resuming mode, pressing ®(Repeat),
ill
(Shuffle) or
CD
(Scan) does
not
function.
If
you
cancel Resuming
mode
by
pressing (
MODE)
or
(ALBM)
+/-, ®(Repeat),
ill
(Shuffle) or
CD
(Scan)
now
function to change the play mode.
•When the ignition key is turned to the
ACC
position,
or
the unit is on, the iPod will be recharged.
•
If
the iPod is disconnected during playback,
playback will pause.
Note
An
anotheriPod cannot be connected using the XA-
110lP or
XA-1201P.
iPod
(CDX-M50IP/MR50IP)
Playing
back
iPod
1Connect the iPod to the dock
connector.
The iPod will tum on automatically, and the
display will appear on the iPod screen
as
below.
Playing tracks
By connecting an iPod
to
the dock connector at
the rear
of
the unit, you can listen on your boat's
speakers, while controlling the iPod from the
unit.
Notes
•When
an
iPod is connectedto the dock connector,
operation from the iPod cannotbe performed.
•Before connef;ting the iPod to the dock connector,
turn down the volume
of
the unit.
•When
not
using the dock connector, use the
supplied dock connector
cap
to prevent water
entering.
•
2Press
(SOURCE)
repeatedly until "PO"
appears.
"PD IPORTABLE" appears, and the tracks
on the iPod start playing automatically from
the point last played.
3Press
(MODE)
to select the play mode.
The mode changes
as
follows:
RESUMING
-+
ALBUM
-+
ARTIST
-+
PLAYLIST
4Adjust the volume.
Press
(OFF)
to stop playback.
To
Skip
Skip
continuously
Press
(ALBM)
+/-
[press once for each]
(ALBM)
+/-
[hold to desired point]
14
Display items
Setting
the
play
mode
I
1
······
E03
I
To change display items, press
(DSPL).
Note
Some
letters stored in iPod
may
not
be
displayed
correctly
Selecting Album, Artist or Playlist
1During playback, press
(MODE).
The mode changes as follows:
ALBUM
-+
ARTIST
-+
PLAYLIST
Skipping albums, artists and
play
lists
I
Track/album/artist name, Track number,
Elapsed playing time, Clock
Tips
•When the iPod is connected to the dock connector,
the
mode
changes to the Resuming mode. In
Resuming mode, pressing ®(Repeat),
ill
(Shuffle) or
CD
(Scan) does
not
function.
If
you
cancel Resuming
mode
by
pressing (
MODE)
or
(ALBM)
+/-, ®(Repeat),
ill
(Shuffle) or
CD
(Scan)
now
function to change the play mode.
•When the ignition key is turned to the
ACC
position,
or
the unit is on, the iPod will be recharged.
•
If
the iPod is disconnected during playback,
playback will pause.
Note
An
anotheriPod cannot be connected using the XA-
110lP or
XA-1201P.
iPod
(CDX-M50IP/MR50IP)
Playing
back
iPod
1Connect the iPod to the dock
connector.
The iPod will tum on automatically, and the
display will appear on the iPod screen
as
below.
Playing tracks
By connecting an iPod
to
the dock connector at
the rear
of
the unit, you can listen on your boat's
speakers, while controlling the iPod from the
unit.
Notes
•When
an
iPod is connectedto the dock connector,
operation from the iPod cannotbe performed.
•Before connef;ting the iPod to the dock connector,
turn down the volume
of
the unit.
•When
not
using the dock connector, use the
supplied dock connector
cap
to prevent water
entering.
•
2Press
(SOURCE)
repeatedly until "PO"
appears.
"PD IPORTABLE" appears, and the tracks
on the iPod start playing automatically from
the point last played.
3Press
(MODE)
to select the play mode.
The mode changes
as
follows:
RESUMING
-+
ALBUM
-+
ARTIST
-+
PLAYLIST
4Adjust the volume.
Press
(OFF)
to stop playback.
To
Skip
Skip
continuously
Press
(ALBM)
+/-
[press once for each]
(ALBM)
+/-
[hold to desired point]
14
Repeat and shuffle Play
1During playback, press ®(REP) or
m(SHUF) repeatedly until the
desired setting appears.
To
return to normal play mode, select
"REP
OFF" or
"SHUF
OFF."
Note
(
ALBM)
+/-
will not work during shuffle
play.
Select
REPTRK
REP
ALB
REP
ART
REP
PLY
SHUF ALB
SHUF ART
SHUF
PLY
SHUF ALL
To
play
track repeatedly.
album repeatedly.
artist repeatedly.
playlist repeatedly.
album in random order.
artist in random order.
playlist in random order.
all tracks in random order.
Other
functions
Changing
the
sound
settings
Adjusting the sound
characteristics
1Press the select button repeatedly
until the desired item appears.
2Rotate the volume control dial to
adjust the selected item.
After 3seconds, the setting is complete and
the display returns to normal play/reception
mode.
The following items can be set (follow the page
reference for details):
"e"
indicates the default settings.
EQ3
To
select an equalizer type: "XPLOD" (e),
"VOCAL," "EDGE," "CRUISE," "SPACE,"
"GRAVITY," "CUSTOM" or "OFF." •
Scan
You can quickly locate aspecific point on the
iPod.
1During playback, press ®until
"SCAN ON" appears.
The first 10 seconds
of
each track will be
played.
To
return to normal play mode, select
"SCAN
OFF."
Note
This function will not work during shuffle play.
DSO
To select the DSO mode:
"1,"
"2"
(e),
"3"
or
"OFF." The larger the number, the more
enhanced the effect.
When tuner/PD*1 is selected as the source, the
default setting is "OFF."
LOW*2,
MID*2,
HI*2
(page 16)
To
customize the equalizer curve.
BAL (Balance)
To adjust the balance between the right and left
speakers: "RIGHT-l
0"
-"CENTER"
(e)-
"LEFT-I0"
FAD
(Fader)
To adjust the balance between the front and rear
speakers: "FRONT-IO" -"CENTER"
(e)-
"REAR
-10"
SUB*3 (Subwoofer volume)
To
adjust the subwoofer volume: "+
10
dB" -
"0
dB"
(e)
-
"-10
dB"
("ATT" is displayed at the lowest setting.)
AUX*4
(AUX level)
To adjust the volume level for each connected
auxiliary equipment. This setting negates the
need to adjust the volume level between sources
(page 17).
Adjustable level: "+18 dB" -
"0
dB"
(e)-
"-8
dB"
*1CDX-M50IP/MR50IP only
*2 When EQ3 is activated.
*3
When the audio output is set to "SUB" (page
16).
*4 When AUXsource is activated.
15
Repeat and shuffle Play
1During playback, press ®(REP) or
m(SHUF) repeatedly until the
desired setting appears.
To
return to normal play mode, select
"REP
OFF" or
"SHUF
OFF."
Note
(
ALBM)
+/-
will not work during shuffle
play.
Select
REPTRK
REP
ALB
REP
ART
REP
PLY
SHUF ALB
SHUF ART
SHUF
PLY
SHUF ALL
To
play
track repeatedly.
album repeatedly.
artist repeatedly.
playlist repeatedly.
album in random order.
artist in random order.
playlist in random order.
all tracks in random order.
Other
functions
Changing
the
sound
settings
Adjusting the sound
characteristics
1Press the select button repeatedly
until the desired item appears.
2Rotate the volume control dial to
adjust the selected item.
After 3seconds, the setting is complete and
the display returns to normal play/reception
mode.
The following items can be set (follow the page
reference for details):
"e"
indicates the default settings.
EQ3
To
select an equalizer type: "XPLOD" (e),
"VOCAL," "EDGE," "CRUISE," "SPACE,"
"GRAVITY," "CUSTOM" or "OFF." •
Scan
You can quickly locate aspecific point on the
iPod.
1During playback, press ®until
"SCAN ON" appears.
The first 10 seconds
of
each track will be
played.
To
return to normal play mode, select
"SCAN
OFF."
Note
This function will not work during shuffle play.
DSO
To select the DSO mode:
"1,"
"2"
(e),
"3"
or
"OFF." The larger the number, the more
enhanced the effect.
When tuner/PD*1 is selected as the source, the
default setting is "OFF."
LOW*2,
MID*2,
HI*2
(page 16)
To
customize the equalizer curve.
BAL (Balance)
To adjust the balance between the right and left
speakers: "RIGHT-l
0"
-"CENTER"
(e)-
"LEFT-I0"
FAD
(Fader)
To adjust the balance between the front and rear
speakers: "FRONT-IO" -"CENTER"
(e)-
"REAR
-10"
SUB*3 (Subwoofer volume)
To
adjust the subwoofer volume: "+
10
dB" -
"0
dB"
(e)
-
"-10
dB"
("ATT" is displayed at the lowest setting.)
AUX*4
(AUX level)
To adjust the volume level for each connected
auxiliary equipment. This setting negates the
need to adjust the volume level between sources
(page 17).
Adjustable level: "+18 dB" -
"0
dB"
(e)-
"-8
dB"
*1CDX-M50IP/MR50IP only
*2 When EQ3 is activated.
*3
When the audio output is set to "SUB" (page
16).
*4 When AUXsource is activated.
15
•
16
Customizing the equalizer curve
-EQ3
"CUSTOM"
of
EQ3 allows you to make your
own equalizer settings.
1Select asource, then press
the
select
button
repeatedly
to
select "EQ3."
2Rotate
the
volume
control
dial
to
select "CUSTOM."
3Press
the
select
button
repeatedly
until
"LOW,"
"MID"
or
"HI"
appears.
4Rotate
the
volume
control
dial
to
adjust
the
selected item.
The volume level is adjustable in 1dB steps,
from
-10
dB
to +10 dB.
a n a• r
L
U"'"
1
+
6d]
Repeat steps 3and 4to adjust the equalizer
curve.
To
restore the factory-set equalizer curve,
press and hold the select button before the
setting is complete.
After 3seconds, the setting is complete and
the display returns
to
normal play/reception
mode.
Tip
Otherequalizer types are also adjustable.
Adjusting
setup
items
-
SET
1Press and
hold
the
select button.
The setup display appears.
2Press
the
select
button
repeatedly
until
the
desired item appears.
3Rotate
the
volume
control
dial
to
select
the
setting
(example
"ON"
or
"OFF").
4Press and
hold
the
select button.
The setup
is
complete and the display returns
to
normal play/reception mode.
Note
Displayed items will differ, depending on the source
and
setting.
The following items can be set (follow the page
reference for details):
"e"
indicates the default settings.
CLOCK-ADJ (Clock Adjust) (page 6)
CT*1
(Clock Time)
To
set "CT-ON" or "CT-OFF" (e) (page 12, 13).
BEEP
To
set "BEEP-ON" (e) or "BEEP-OFF."
AUX-A*2 (AUX Audio)
To
tum the AUX source display "AUX-A-ON"
(e) or "AUX-A-OFF" (page 17).
A.OFF (Auto Off)
To
shut off automatically after adesired time
when the unit is turned off,
-"A.OFF-NO" (e), "A.OFF-30S (Seconds),"
"A.OFF-30M (Minutes)" or "A.OFF-60M
(Minutes)."
REARISUB*2
To
switch the audio output.
-"REAR-OUT" (e): to output to apower
amplifier.
-"SUB-OUT": to output to asubwoofer.
DEMO (Demonstration)
To
set "DEMO-ON" (e) or "DEMO-OFF."
DIMMER
To
change the brightness
of
the display.
-"DIMMER-AT" (e): to dim the display
automatically when you tum lights on.
-"DIMMER-OFF": to deactivate the dimmer.
-"DIMMER-ON": to dim the display.
CONTRAST
To
adjust the contrast
of
the display.
The contrast level is adjustable in 7steps.
ILLUMI (Illumination)
To
change the illumination color:
"ILLUMI-l"
(e) or "ILLUMI-2."
•
16
Customizing the equalizer curve
-EQ3
"CUSTOM"
of
EQ3 allows you to make your
own equalizer settings.
1Select asource, then press
the
select
button
repeatedly
to
select "EQ3."
2Rotate
the
volume
control
dial
to
select "CUSTOM."
3Press
the
select
button
repeatedly
until
"LOW,"
"MID"
or
"HI"
appears.
4Rotate
the
volume
control
dial
to
adjust
the
selected item.
The volume level is adjustable in 1dB steps,
from
-10
dB
to +10 dB.
a n a• r
L
U"'"
1
+
6d]
Repeat steps 3and 4to adjust the equalizer
curve.
To
restore the factory-set equalizer curve,
press and hold the select button before the
setting is complete.
After 3seconds, the setting is complete and
the display returns
to
normal play/reception
mode.
Tip
Otherequalizer types are also adjustable.
Adjusting
setup
items
-
SET
1Press and
hold
the
select button.
The setup display appears.
2Press
the
select
button
repeatedly
until
the
desired item appears.
3Rotate
the
volume
control
dial
to
select
the
setting
(example
"ON"
or
"OFF").
4Press and
hold
the
select button.
The setup
is
complete and the display returns
to
normal play/reception mode.
Note
Displayed items will differ, depending on the source
and
setting.
The following items can be set (follow the page
reference for details):
"e"
indicates the default settings.
CLOCK-ADJ (Clock Adjust) (page 6)
CT*1
(Clock Time)
To
set "CT-ON" or "CT-OFF" (e) (page 12, 13).
BEEP
To
set "BEEP-ON" (e) or "BEEP-OFF."
AUX-A*2 (AUX Audio)
To
tum the AUX source display "AUX-A-ON"
(e) or "AUX-A-OFF" (page 17).
A.OFF (Auto Off)
To
shut off automatically after adesired time
when the unit is turned off,
-"A.OFF-NO" (e), "A.OFF-30S (Seconds),"
"A.OFF-30M (Minutes)" or "A.OFF-60M
(Minutes)."
REARISUB*2
To
switch the audio output.
-"REAR-OUT" (e): to output to apower
amplifier.
-"SUB-OUT": to output to asubwoofer.
DEMO (Demonstration)
To
set "DEMO-ON" (e) or "DEMO-OFF."
DIMMER
To
change the brightness
of
the display.
-"DIMMER-AT" (e): to dim the display
automatically when you tum lights on.
-"DIMMER-OFF": to deactivate the dimmer.
-"DIMMER-ON": to dim the display.
CONTRAST
To
adjust the contrast
of
the display.
The contrast level is adjustable in 7steps.
ILLUMI (Illumination)
To
change the illumination color:
"ILLUMI-l"
(e) or "ILLUMI-2."
M.DSPl
(Motion Display)
To
select the Motion Display mode.
-"M.DSPL-SA" (e): to show moving patterns
and spectrum analyzer.
-"M.DSPL-ON": to show moving patterns.
-"M.DSPL-OFF": to deactivate the Motion
Display.
A.SCRl
(Auto Scroll)
To scroll long displayed item automatically
when the disc/album/track is changed.
-"A.SCRL-ON" (e): to scroll.
-"A.SCRL-OFF": to not scroll.
lOCAL
(Local Seek Mode)
-
"LOCAL-ON"
:to only tune into stations with
stronger signals.
-"LOCAL-OFF" (e): to tune normal reception.
MONO*3
(Monaural Mode)
To improve poor FM reception, select monaural
reception mode.
-
"MONO-ON"
:to hear stereo broadcast in
monaural.
-"MONO-OFF" (e): to hear stereo broadcast in
stereo.
REG*1*3
(Regional)
To set "REG-ON" (e)
or
"REG-OFF" (page 13).
lPF*4 (Low Pass Filter)
To select the subwoofer cut-offfrequency:
"LPF
OFF" (e),
"LPFI25Hz"
or
"LPF
78Hz."
lOUD
(Loudness)
To allow you to listen clearly at low volume
levels.
-"LOUD-ON" :to reinforce bass and treble.
-"LOUD-OFF" (e): to not reinforce bass and
treble.
BTM (page
11)
*1CDX-MR50IP only
*2 When the unit
is
turned
off.
*3 When FM
is
received.
*4 When the audio output
is
set
to
"SUB."
Using
optional
equipment
Auxiliary audio equipment
By connecting an optional portable audio device
to the AUX input
jack
(stereo mini jack) on the
unit and then simply selecting the source, you
can listen on your boat's speakers. The volume
level is adjustable for any difference between the
unit and the portable audio device. Follow the
procedure below:
Connecting the portable audio
device
1Turn offthe portable audio device.
2
Tum
down the volume on the unit.
3Connect to the unit.
Connecting
cord*
(not supplied)
*Be sure to use astraight type plug.
Adjust the volume level
Be sure to adjust the volume for each connected
audio device before playback.
1Turn down the volume on the unit.
2Press
(SOURCE)
repeatedly until "AUX"
appears.
"AUX FRONT IN" appears.
3Start playback
of
the portable audio device at a
moderate volume.
4Set your usual listening volume on the unit.
5Adjust the input level (page 15).
•
17
M.DSPl
(Motion Display)
To
select the Motion Display mode.
-"M.DSPL-SA" (e): to show moving patterns
and spectrum analyzer.
-"M.DSPL-ON": to show moving patterns.
-"M.DSPL-OFF": to deactivate the Motion
Display.
A.SCRl
(Auto Scroll)
To scroll long displayed item automatically
when the disc/album/track is changed.
-"A.SCRL-ON" (e): to scroll.
-"A.SCRL-OFF": to not scroll.
lOCAL
(Local Seek Mode)
-
"LOCAL-ON"
:to only tune into stations with
stronger signals.
-"LOCAL-OFF" (e): to tune normal reception.
MONO*3
(Monaural Mode)
To improve poor FM reception, select monaural
reception mode.
-
"MONO-ON"
:to hear stereo broadcast in
monaural.
-"MONO-OFF" (e): to hear stereo broadcast in
stereo.
REG*1*3
(Regional)
To set "REG-ON" (e)
or
"REG-OFF" (page 13).
lPF*4 (Low Pass Filter)
To select the subwoofer cut-offfrequency:
"LPF
OFF" (e),
"LPFI25Hz"
or
"LPF
78Hz."
lOUD
(Loudness)
To allow you to listen clearly at low volume
levels.
-"LOUD-ON" :to reinforce bass and treble.
-"LOUD-OFF" (e): to not reinforce bass and
treble.
BTM (page
11)
*1CDX-MR50IP only
*2 When the unit
is
turned
off.
*3 When FM
is
received.
*4 When the audio output
is
set
to
"SUB."
Using
optional
equipment
Auxiliary audio equipment
By connecting an optional portable audio device
to the AUX input
jack
(stereo mini jack) on the
unit and then simply selecting the source, you
can listen on your boat's speakers. The volume
level is adjustable for any difference between the
unit and the portable audio device. Follow the
procedure below:
Connecting the portable audio
device
1Turn offthe portable audio device.
2
Tum
down the volume on the unit.
3Connect to the unit.
Connecting
cord*
(not supplied)
*Be sure to use astraight type plug.
Adjust the volume level
Be sure to adjust the volume for each connected
audio device before playback.
1Turn down the volume on the unit.
2Press
(SOURCE)
repeatedly until "AUX"
appears.
"AUX FRONT IN" appears.
3Start playback
of
the portable audio device at a
moderate volume.
4Set your usual listening volume on the unit.
5Adjust the input level (page 15).
•
17
RM-X55M
Marine
remote
commander
RM-X55M1X11 M
GP/ALBM
-/+
(fPIo~--
MODE
rltt:t==~\t~r-
SEEK
-/+
MUTING
(ATT)
OFF--~
-.......:::::::::=::::::::--~
VOLUME
--.....,....:::~~~
+/-
RM-X11M
Location
of
controls
The corresponding buttons on the marine remote
commander control the same functions as those
on this unit.
j.
EC3
Disc number
Playback starts.
Skipping albums and
discs
1During playback, press
(ALBM)
+/-.
CD/MD
changer
Selecting the changer
1Press
(SOURCE)
repeatedly until "CD" or
"MD"
appears.
2Press
(MODE)
repeatedly until the desired
changer appears.
Unit number
•
Repeat and shuffle play
1During playback, press
CD
(REP) or
ill
(SHUF) repeatedly until the desired setting
appears.
To
skip
album
album
continuously
discs
discs
continuously
Select
4DISC
SHUF
CHANGER
SHUF
ALL*
Press (ALBM )
and release (hold for a
moment).
within 2seconds
of
first
releasing.
repeatedly.
then, press again within 2
seconds and hold.
To play
disc repeatedly.
tracks in the changer in random
order.
tracks in all units
in
random
order.
VOL
+/-
-~~-=-rl;:li
I P ........
:loor--
MODE
OFF
--"""I"!~~I~;;;~~~~_
)i=
SEEK-I+
"","""",,~~-I-I-
SOURCE
GP/ALBM
-1+
---..;~:oo:::::======-~
The following controls on the marine remote
commander require adifferent operation from
the unit.
•VOLUME (VOL)
+/-
button(s)
The same as the volume control dial on the
unit.
•GP/ALBM
-/+
button(s)
The same as
(ALBM)
-/+
on the unit.
•MUTING
button
To attenuate the sound. (The same as
(A
TT)
on
the card remote commander.)
*When one
or
more CD changers,
or
two
or
more MD
changers are connected.
To
return to normal play mode, select
"4
OFF"
or "SHUF
OFF."
Tip
"$HUF
ALL:' will notshuffle tracks between CD units
and
MD changers.
18
RM-X55M
Marine
remote
commander
RM-X55M1X11 M
GP/ALBM
-/+
(fPIo~--
MODE
rltt:t==~\t~r-
SEEK
-/+
MUTING
(ATT)
OFF--~
-.......:::::::::=::::::::--~
VOLUME
--.....,....:::~~~
+/-
RM-X11M
Location
of
controls
The corresponding buttons on the marine remote
commander control the same functions as those
on this unit.
j.
EC3
Disc number
Playback starts.
Skipping albums and
discs
1During playback, press
(ALBM)
+/-.
CD/MD
changer
Selecting the changer
1Press
(SOURCE)
repeatedly until "CD" or
"MD"
appears.
2Press
(MODE)
repeatedly until the desired
changer appears.
Unit number
•
Repeat and shuffle play
1During playback, press
CD
(REP) or
ill
(SHUF) repeatedly until the desired setting
appears.
To
skip
album
album
continuously
discs
discs
continuously
Select
4DISC
SHUF
CHANGER
SHUF
ALL*
Press (ALBM )
and release (hold for a
moment).
within 2seconds
of
first
releasing.
repeatedly.
then, press again within 2
seconds and hold.
To play
disc repeatedly.
tracks in the changer in random
order.
tracks in all units
in
random
order.
VOL
+/-
-~~-=-rl;:li
I P ........
:loor--
MODE
OFF
--"""I"!~~I~;;;~~~~_
)i=
SEEK-I+
"","""",,~~-I-I-
SOURCE
GP/ALBM
-1+
---..;~:oo:::::======-~
The following controls on the marine remote
commander require adifferent operation from
the unit.
•VOLUME (VOL)
+/-
button(s)
The same as the volume control dial on the
unit.
•GP/ALBM
-/+
button(s)
The same as
(ALBM)
-/+
on the unit.
•MUTING
button
To attenuate the sound. (The same as
(A
TT)
on
the card remote commander.)
*When one
or
more CD changers,
or
two
or
more MD
changers are connected.
To
return to normal play mode, select
"4
OFF"
or "SHUF
OFF."
Tip
"$HUF
ALL:' will notshuffle tracks between CD units
and
MD changers.
18
Additional
Information
Precautions
•
If
your boat has been moored in direct sunlight,
allow the unit to cool
off
before operating it.
•Power antenna (aerial) will extend automatically
while the unit is operating.
Moisture condensation
On arainy day
or
in avery damp area, moisture
condensation may occur inside the lenses and
display
of
the unit. Should this occur, the unit will
not operate properly. In such acase, remove the disc
and wait for about an hour until the moisture has
evaporated.
To
maintain high sound quality
Be careful not to splash juice or other soft drinks
onto the unit or discs.
Notes on
discs
•To keep adisc clean, do not touch its surface.
Handle the disc by its edge.
•Keep your discs in their cases
or
disc magazines
when not
in
use.
•Do not subject discs to heat/high temperature.
Avoid leaving them in amoored boat.
•
Do
not attach labels, or use discs with sticky inkJ
residue. Such discs may stop spinning when used,
causing amalfunction,
or
may ruin the disc.
•Do not use any discs with labels or stickers
attached.
The following malfunctions may result from using
such discs:
-Inability to eject adisc (due to alabel
or
sticker
peeling
off
and jamming the eject mechanism).
-Inability to read audio data correctly (e.g.,
playback skipping,
or
no
playback~
due
t~
heat
shrinking
of
asticker or label causIng a
diSC
to
warp.
•Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this
un~t.
Attempting to do so may damage the umt. Do not
use such discs.
•You cannot play 8em (3 1/4in) CDs.
•Before playing, clean the discs
with acommercially available
cleaning cloth. Wipe each disc
from the center out.
Do
not use
solvents such as benzine,
thinner, commercially available
cleaners,
or
antistatic spray
intended for analog discs.
Notes on CD-R1CD-RW discs
•Some CD-Rs/CD-RWs (depending on the
equipment used for its recording
or
the condition
of
the disc) may not play on this unit.
•
You
cannot
playa
CD-RIa CD-RW that
is
not
finalized.
•The unit is compatible with the ISO 9660 level II
level 2format, Joliet/Romeo in the expansion
format, and Multi Session.
•The maximum number of:
-folders (albums): 150 (including root and empty
folders).
-files (tracks) and folders contained in adisc: 300 _
(if afolder/file names contain many characters,
this number may become less than 300).
-displayable characters for afolder/file name is
32 (Joliet),
or
64 (Romeo).
•When the disc is recorded in Multi Session, only
the first track
of
the first session format is
recognized and played (any other format is
skipped). The priority
of
the format
is
CD-DA and
MP3IWMAIAAC.
-When the first track is aCD-DA, only CD-DA
of
the first session
is
played.
-When the first track is not aCD-DA, the MP3/
WMAIAAC session is played.
If
the disc has no
data
in
any
of
these formats,
"NO
MUSIC" is
displayed.
Music discs encoded with copyright
protection technologies
This product
is
designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed by
some record companies. Please be aware that among
those discs, there are some that do not conform to
the
CD
standard and may not be playable by this
product.
Note on DualDiscs
ADualDisc is atwo sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side. However,
since the audio material side does not conform to
the Compact Disc (CD) standard, playback on this
product is not guaranteed.
19
Additional
Information
Precautions
•
If
your boat has been moored in direct sunlight,
allow the unit to cool
off
before operating it.
•Power antenna (aerial) will extend automatically
while the unit is operating.
Moisture condensation
On arainy day
or
in avery damp area, moisture
condensation may occur inside the lenses and
display
of
the unit. Should this occur, the unit will
not operate properly. In such acase, remove the disc
and wait for about an hour until the moisture has
evaporated.
To
maintain high sound quality
Be careful not to splash juice or other soft drinks
onto the unit or discs.
Notes on
discs
•To keep adisc clean, do not touch its surface.
Handle the disc by its edge.
•Keep your discs in their cases
or
disc magazines
when not
in
use.
•Do not subject discs to heat/high temperature.
Avoid leaving them in amoored boat.
•
Do
not attach labels, or use discs with sticky inkJ
residue. Such discs may stop spinning when used,
causing amalfunction,
or
may ruin the disc.
•Do not use any discs with labels or stickers
attached.
The following malfunctions may result from using
such discs:
-Inability to eject adisc (due to alabel
or
sticker
peeling
off
and jamming the eject mechanism).
-Inability to read audio data correctly (e.g.,
playback skipping,
or
no
playback~
due
t~
heat
shrinking
of
asticker or label causIng a
diSC
to
warp.
•Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this
un~t.
Attempting to do so may damage the umt. Do not
use such discs.
•You cannot play 8em (3 1/4in) CDs.
•Before playing, clean the discs
with acommercially available
cleaning cloth. Wipe each disc
from the center out.
Do
not use
solvents such as benzine,
thinner, commercially available
cleaners,
or
antistatic spray
intended for analog discs.
Notes on CD-R1CD-RW discs
•Some CD-Rs/CD-RWs (depending on the
equipment used for its recording
or
the condition
of
the disc) may not play on this unit.
•
You
cannot
playa
CD-RIa CD-RW that
is
not
finalized.
•The unit is compatible with the ISO 9660 level II
level 2format, Joliet/Romeo in the expansion
format, and Multi Session.
•The maximum number of:
-folders (albums): 150 (including root and empty
folders).
-files (tracks) and folders contained in adisc: 300 _
(if afolder/file names contain many characters,
this number may become less than 300).
-displayable characters for afolder/file name is
32 (Joliet),
or
64 (Romeo).
•When the disc is recorded in Multi Session, only
the first track
of
the first session format is
recognized and played (any other format is
skipped). The priority
of
the format
is
CD-DA and
MP3IWMAIAAC.
-When the first track is aCD-DA, only CD-DA
of
the first session
is
played.
-When the first track is not aCD-DA, the MP3/
WMAIAAC session is played.
If
the disc has no
data
in
any
of
these formats,
"NO
MUSIC" is
displayed.
Music discs encoded with copyright
protection technologies
This product
is
designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed by
some record companies. Please be aware that among
those discs, there are some that do not conform to
the
CD
standard and may not be playable by this
product.
Note on DualDiscs
ADualDisc is atwo sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side. However,
since the audio material side does not conform to
the Compact Disc (CD) standard, playback on this
product is not guaranteed.
19
II
20
Playback order of MP3IWMAIAAC
files
(""""--, Folder
L-J
(album)
~
MP3IWMA/
AAC
file
(track)
About MP3 files
•MP3, which stands for
MPEG-l
Audio Layer-3,
is
amusic file compression format standard. It
compresses audio CD data to approximately 1/10
of
its original size.
•ID3 tag versions 1.0, 1.1, 2.2, 2.3 and
204
apply to
MP3 only.
103
tag
is
15/30 characters (1.0 and
1.1), or 63/126 characters (2.2, 2.3 and
204).
•When naming an MP3 file, be sure to add the file
extension ".mp3"
to
the file name.
•During playback or fast-forward/reverse
of
aVBR
(variable bit rate) MP3 file, elapsed playing time
may not display accurately.
Note
Ifyou
playa
high-bit-rate MP3, such
as
320 kbps,
sound
may
be intermittent.
About WMA files
•WMA, which stands for Windows Media Audio,
is amusic file compression format standard. It
compresses audio CD data to approximately 1/22*
of
its original size.
•WMA tag
is
63 characters.
•When naming aWMA file, be sure to add the file
extension ".wma" to the file name.
•During playback or fast-forward/reverse
of
aVBR
(variable bit rate) WMA file, elapsed playing time
may not display accurately.
*only for 64 kbps
Note
Playback
of
the foffowing
WMA
files is not supported.
-lossless compression
-copyright-protected
About AAC files
•AAC, which stands for Advanced Audio Coding,
is amusic file compression format standard.
It
compresses audio CD data to approximately 1/11*
of
its original size.
•AAC tag is 126 characters.
•When naming an AAC file, be sure
to
add the file
extension ".m4a"
to
the file name.
•During playback orfast-forward/reverse
of
aVBR
(variable bit rate) AAC file, elapsed playing time
may not display accurately.
*only for 128 kbps
NoteonAAC
Playback
of
acopyright-protected file is notsupported.
About iPod (CDX-M50IP/MR50IP)
This unit can be used with the dock connector type
iPod, iPod photo, iPod mini and iPod nano with the
following software versions. All other versions
earlier than listed are not guaranteed.
-Third-generation iPod: Ver.2.3.0
-Fourth-generation iPod: Ver.3.1.1
-Fifth-generation iPod: Ver.l.2
-iPod photo: Ver.l.2.1
-iPod mini: Ver.IA.I
-First-generation iPod nano: Ver.I.3
-Second-generation iPod nano: Ver.l.l
(video function
of
fifth-generation iPod and
photo function
of
iPod photo are not supported).
For customers in USA, please visit the following
site for further information:
http://www.xplodsony.com
If
you have any questions or problems concerning
your unit that are not covered
in
this manual, consult
your nearest Sony dealer.
Maintenance
Replacing the lithium battery of the
card remote commander
Under normal conditions, the battery will last
approximately Iyear. (The service life may be
shorter, depending on the conditions
of
use.)
When the battery becomes weak, the range
of
the
card remote commander becomes shorter. Replace
the battery with anew CR2025 lithium battery. Use
of
any other battery may present arisk
of
fire or
explosion.
II
20
Playback order of MP3IWMAIAAC
files
(""""--, Folder
L-J
(album)
~
MP3IWMA/
AAC
file
(track)
About MP3 files
•MP3, which stands for
MPEG-l
Audio Layer-3,
is
amusic file compression format standard. It
compresses audio CD data to approximately 1/10
of
its original size.
•ID3 tag versions 1.0, 1.1, 2.2, 2.3 and
204
apply to
MP3 only.
103
tag
is
15/30 characters (1.0 and
1.1), or 63/126 characters (2.2, 2.3 and
204).
•When naming an MP3 file, be sure to add the file
extension ".mp3"
to
the file name.
•During playback or fast-forward/reverse
of
aVBR
(variable bit rate) MP3 file, elapsed playing time
may not display accurately.
Note
Ifyou
playa
high-bit-rate MP3, such
as
320 kbps,
sound
may
be intermittent.
About WMA files
•WMA, which stands for Windows Media Audio,
is amusic file compression format standard. It
compresses audio CD data to approximately 1/22*
of
its original size.
•WMA tag
is
63 characters.
•When naming aWMA file, be sure to add the file
extension ".wma" to the file name.
•During playback or fast-forward/reverse
of
aVBR
(variable bit rate) WMA file, elapsed playing time
may not display accurately.
*only for 64 kbps
Note
Playback
of
the foffowing
WMA
files is not supported.
-lossless compression
-copyright-protected
About AAC files
•AAC, which stands for Advanced Audio Coding,
is amusic file compression format standard.
It
compresses audio CD data to approximately 1/11*
of
its original size.
•AAC tag is 126 characters.
•When naming an AAC file, be sure
to
add the file
extension ".m4a"
to
the file name.
•During playback orfast-forward/reverse
of
aVBR
(variable bit rate) AAC file, elapsed playing time
may not display accurately.
*only for 128 kbps
NoteonAAC
Playback
of
acopyright-protected file is notsupported.
About iPod (CDX-M50IP/MR50IP)
This unit can be used with the dock connector type
iPod, iPod photo, iPod mini and iPod nano with the
following software versions. All other versions
earlier than listed are not guaranteed.
-Third-generation iPod: Ver.2.3.0
-Fourth-generation iPod: Ver.3.1.1
-Fifth-generation iPod: Ver.l.2
-iPod photo: Ver.l.2.1
-iPod mini: Ver.IA.I
-First-generation iPod nano: Ver.I.3
-Second-generation iPod nano: Ver.l.l
(video function
of
fifth-generation iPod and
photo function
of
iPod photo are not supported).
For customers in USA, please visit the following
site for further information:
http://www.xplodsony.com
If
you have any questions or problems concerning
your unit that are not covered
in
this manual, consult
your nearest Sony dealer.
Maintenance
Replacing the lithium battery of the
card remote commander
Under normal conditions, the battery will last
approximately Iyear. (The service life may be
shorter, depending on the conditions
of
use.)
When the battery becomes weak, the range
of
the
card remote commander becomes shorter. Replace
the battery with anew CR2025 lithium battery. Use
of
any other battery may present arisk
of
fire or
explosion.
Other manuals for CDXM60UI - Marine CD Receiver MP3/WMA/AAC...
9
This manual suits for next models
2
Table of contents
Other Sony Marine Audio manuals
Sony
Sony XS-F1021 User manual
Sony
Sony XS-C69BR User manual
Sony
Sony XS-HF137 Product guide
Sony
Sony CDX-H905IP User manual
Sony
Sony XS-HA1327 Product guide
Sony
Sony XS-HA1326 Product guide
Sony
Sony MEX-M72BT User manual
Sony
Sony XS-GT1028F Installation instructions manual
Sony
Sony XS-A825 Product guide
Sony
Sony XS-GT1627A User manual
Sony
Sony XS-A1024 Product guide
Sony
Sony XS-HA1724 Product guide
Sony
Sony XS-HT130CN User manual
Sony
Sony XS-F6920 User manual
Sony
Sony XS-7303 User manual
Sony
Sony CDX-M20 User manual
Sony
Sony XS-6029 User manual
Sony
Sony XS-A1726 Product guide
Sony
Sony XS-AR1025 Product guide
Sony
Sony DSX-M80 Reference guide
