Sony Triniton GDM-20SHT User manual

GDM·20SHT
SERVICE MANUAL
Chassis No. SCC-H71A-A
Multiscan 20sh
•••••
•••••
•••
MICROFILM
SPECIFICATIONS
Picture tube 0.25 mm aperture grille pitch
20 inches measured diagonally
(19" visual)
90-degree denection
Effective picture size Approx. 384 x 290 mm (w /h)
(15 1ft x 11 In inches)
Display picture size Approx. 373 x 280
mm (w /h)
(14 y, x 11 1;" inches)
Resolution
or
Approx. 350 x 280 mm (w /h)
(13 %x 11 1,1" inches)
Horizontal: 640- to 1600 dots (-VGA
mode)
Vertical: 480- to 1200 lines (-VGA
mode)
Deflection frequency Horizontal: 30 to 107 kHz
Vertical: 50 to 160 Hz
Input signal Sync:
Sync
on Green: 0.286 Vp·p, Negative
H/V Composite Sync: 75 ohms/2
kohms, TIL Positive/Negative
H. Sync/V. Sync Separate: 75 ohms/
2 kohms, TIL Positive/Negative
Video:
R/G/B: 0.714 Vp-p, Positive
AC
input voltage/current
100 to 120 V, 50/60 Hz, max. 2.5 A
200 to 240 V, 50 - 60 Hz, max. 1.2 A
Dimensions Approx.
474 x 474 x 502 mm (w/h/d)
(18 1f. x 18 Yt x 19 Yt inches)
Mass Approx. 31 kg (68 Ib 4 oz)
Supplied ilCc('s5ories AC power cord (1)
15-pin mini D-sub (HD15 -HOtS)
videu cable (1)
Ferrite core (1)
Binder (1)
Design and specifications are subject to change without
notice.
P-5 CHASSIS
For Service Manuals
MAURITRON SERVICES
B Cherry Tree Road, Chlnnor
Oxfordshlre, OX9 4Qy'
Tel [phone]
Fax [phone]
email:[email protected]
TRINITRON® COLOR GRAPHIC DISPLAY
SONY

GDM-20SHT
Power Saving Function
This monitor meets the power saving guidelines set by
TCOn guidelines (NUTEK). It is capable of reduced power
consumption when used with a computer equipped with
Display Power Management Signaling (DPMS). By sensing
the
absence of the sync signal coming from the computer, it
will
reduce the power consumption as follows:
Normal operation
100%
2
Suspend
approx.l0%
(1st step of power saving)
Active-off
3 (2nd
step of power saving)
approx.7%
TIMING SPECIFICATION
Mode 1 2 3
Graphics mode
YGA YESA-75 Macintosh
(Graphics) 16" Color
Resolution (H x V)
640 x 480
800 x 600
832 x 624
Oat Clock 25.17 MHz
49.5 MHz
57.283 MHz
H Frequency
310463 kHz 46.875 kHz 49.725 kHz
HTotal
31.784 ~S 21.333 ~S 20.111 ~
H Front porch 0.318
~S 0.323 ~S 0.559 ~
HSync width
3.814 ~S 1616 ~S 1.117~
H Back porch 1.589
~S 3.232 ~S 3.910 ~S
H Blanking 5.721
~S 5.172 ~S 5.586 ~S
H Active Area 26.063
~
16.162 ~S 14.524 ~S
V Frequency 59.929 Hz
75.000 Hz 74.550
Hz
V Total 525 H Lines
625 H Lines 667 H Lines
Y Front porch 2 H Lines 1 H Line 1 H Line
Y Sync
width
2 H Lines 3 H Lines 3 H Lines
Y Back porch
25 H Lines 21 H Lines 39 H Lines
Y Blanking
29 H Lines 25 H Lines
43 H Lines
Y Active Area 496 H Lines
600 H Lines 624 H Lines
Sync External External External
Sync Polarity H H
(+)
H
Sync Polarity V H
(+)
(-)
Scan Mode
Non- Non- Non-
interlace interlace interlace
1) VGA does not include the border area.
2) Recommended horizontal frequency timings are:
Horizontal front porch
is 0.1 ~sec or more.
Horizontal sync. width is 0.8 ~sec or more.
Horizontal back porth
is 0.6 ~sec or more.
Horizontal blanking width is 2.4 ~sec or more.
CAUTION: The Power Saving function will automatically
put the monitor into the Active-off state if the
power switch is turned on without any video
signal input. Once the horizontal and vertical
syncs are sensed, the monitor will automatically
return to its Normal operation state.
green on off
approx. 3 sec. green on
orange on
approx. 10 sec. off orange
on
4 5 6 7 8
Macintosh Macintosh YESA-75 YESA-75 VESA-80
19"
Color
21" Color
1024 x 768 1152 x 870 1280 x 1024 1600 x 1200 1600 x 1200
80 MHz 100 MHz 135 MHz
202.5 MHz 216 MHz
60.241 kHz 68.681 kHz 79.976 kHz 93.750 kHz 100.00 kHz
16.600 ~
14.560 ~
12.504 ~
10.667 ~S
10.000 ~S
0.550 ~
0.320 ~S
0.119 ~
0.316 ~S 0.296 ~S
1.200 ~
1.280 ~ 1.067 ~S 0.948 ~
0.889 ~
2.050 ~S 1.440~ 1.837 ~S
1.501 ~S 10407 ~S
3.800 ~S 3.040 ~S 3.022~
2.765 ~S
2.593 ~S
12.800 ~S
11.520 ~S 9.481 ~S
7.901 ~S
7.407 ~S
74.927 Hz 75.062 Hz 75.025 Hz
75.000 Hz
80.000 Hz
804 H Lines 915 H Lines 1066 H Lines 1250 H Lines
1250 H Lines
3 H Lines 3 H Lines 1 H Line 1 H Line 1 H Line
3 H Lines 3 H Lines 3 H Lines 3 H Lines 3 H Lines
30 H Lines
39 H Lines
38 H Lines 46 H Lines
46 H Lines
36 H Lines 45 H Lines 42 H Lines
50 H Lines
50 H Lines
768 H Lines 870 H Lines
1024 H Lines
1200 H Lines
1200 H Lines
External External External External External
(-)
H (+)
(+) (+)
(-)
(-)
(+) (+) (+)
Non- Non- Non- Non- Non-
interlace interlace interlace interlace interlace
-2-
9
YESA-85
1600 x 1200
229.5 MHz
106.250 kHz
9.412
~
0.279 ~S
0.837~
1.325 ~S
2.440 ~S
6.972~
85.000 Hz
1250 H Lines
1 H Line
3 H Lines
46 H Lines
50 H Lines
1200 H Lines
External
(+)
(+)
Non-
interlace

GDM-20SHT
SAFETY CHECK-OUT
(US Model only)
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-sol:
dered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly tran-
sistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values.
Make sure your instruments are accurate; be suspicious of
your HV meter if sets always have low HV.
8. Check the antenna terminals, metal trim, "metallized"
knobs, screws, and all other exposed metal parts for AC
Leakage. Check leakage as described below.
O.1SIlF
To Exposed Metal
Parts on
Set
1.5 kfl
AC
Voltmeter
(0.75 V)
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 rnA (500 microampers).
Leakage current can be measured by anyone of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers' instructions to
use these instruments.
2. A battery-operated AC milliammeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
YOM or battery-operated AC voltmeter. The "limit" indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all
battery operated digital multimeters that have a 2 V AC
range are suitable. (See Fig. A)
WARNING!!
NEVER TURN ON THE POWER IN A CONDITION IN
WHICH THE DEGAUSS COIL HAS BEEN REMOVED.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED
BY SHADING AND MARK .&
ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS
AND IN THE PARTS LIST ARE CRITICAL FOR SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED
IN
THIS MANUAL. FOLLOW THESE PROCEDURES
WHENEVER CRITICAL COMPONENTS ARE REPLACED
OR IMPROPER OPERATION IS SUSPECTED.
AVERTISSEMENT!!
NE JAMAIS METTRE SOUS TENSION QUAND LA
BOBINE DE DEMAGNETISATION EST ENLEVEE.
ATIENTION AUX COMPOSANTS RELATIFS A LA
SECURITE!!
-=- Earth Ground LES COMPOSANTS IDENTIFIES PAR UNE TRAME ET
PAR UNE MARQUE .& SUR LES SCHEMAS DE
Fig. A. Using an AC voltmeter to check AC leakage. PRINCIPE, LES VUES EXPLOSEES ET LES LlSTES DE
PIECES SONT D'UNE IMPORTANCE CRITIQUE POUR LA
SECURITE DU FONCTIONNEMENT. NE LES REM-
PLACER QUE PAR DES COMPOSANTS SONY DONT
LE
NUMERO DE PIECE EST INDlQUE DANS LE PRESENT
MANUEL OU DANS DES SUPPLEMENTS PUB LIES PAR
SONY. LES REGLAGES DE CIRCUIT DONT L'IMPOR-
TANCE EST CRITIQUE POUR LA SECURITE DU
FONCTIONNEMENT SONT IDENTIFIES DANS LE
PRESENT MANUEL. SUIVRE CES PROCEDURES LORS . .~
DE CHAQUE REMPLACEMENT DE COMPOSANTS
CRITIQUES, OU LORSQU'UN MAUVAIS FONCTIONNE-
MENT EST SUSPECTE.
-3-

GDM-20SHT
TABLE OF CONTENTS
1. GENERAL ............................................. ·.··· ................. 5
2. DISASSEMBLY
2-1. Rear Cabinet and Top Cover Removal............... 7
2-2. D Block Assy Removal....................................... 7
2-3. Power Block Assy Removal............................... 8
2-4. L Board Removal ................................................ 8
2-5. M Board Removal ............................................... 9
2-6. A Block Assy Removal....................................... 9
2-7. H Board Removal ................................................
10
2-8. Picture Tube Removal......................................... 10
2-9. Wiring Harness Layout .......................................
11
3. SAFETY RELATED ADJUSTMENT ............. 12
4. ADJUSTMENTS ...................................................... 13
5. DIAGRAMS
5-1. Block Diagrams ................................................... 17
5-2. Frame Schematic Diagram .................................. 25
5-3. Circuit Boards Location ...................................... 27
5-4. Schematic Diagrams and Printed Wiring Boards
(1) Schematic Diagrams of D and L Boards ............ 31
(2) Schematic Diagram of DA Board ....................... 35
(3) Schematic Diagram of A Board .......................... 45
(4) Schematic Diagrams
of DB, G, Hand
M Boards ......................................................... 49
5-5. Semiconductors ................................................... 56
6. EXPLODED VIEWS
6-1. Chassis... .............................................................. 57
6-2. Picture Tube ........................................................ 58
6-3. Packing Materials ................................................ 59
7. ELECTRICAL PARTS LIST ............................ 61
-4-

U1
I
The operating Instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remeln as In the manual.
SECTION 1
GENERAL
Function of Controls
See the given pages for further descnption.
Front panel
Rear panel
4 ,
'.
i •.
II II
ill RESET button (page 10)
Resets
the adjustment data to the factory-preset levels
for
the Input Signal being received.
III M01RE button and indicator (page 10)
Eliminates moire.
~ Adjustment parameter buttons and indicators
Select the adjustment parameters. The mdlcator of the
selected parameter lights.
ROTATION: Raster rotation and color distortion
(page 101
COLOR: Color temperature (page 9)
CONY: Convergence (page 9)
SHAPE: Pincushion and keystone distortions (page 9)
SIZE: Picture size (page 9)
CENTER:
Centering (page 8)
[II 0. (brightnes!.) buttons
Adjust the picture bnghtness in normal operation mode
(page 8).
Act
as +/- or % controls to adjust pICture size,
centenng, convergence, rotation, keystone distortion and
coJor temperature (pages 8 - 10).
~ () (contrast) buttons
Adjust the picture contrast in normal operation mode
(page 8).
Act as +/- or ¢fc> controls to adjust picture size,
centering, con\"t:~rgence, beam landing, pincushIOn
distortion, color temperature and moire (pages 8 - 10).
[ID roWEI{ SA VIt\:G indicato( (page II)
Lights up when the mom tor is in Power Saving mode.
Flashes when the limit value for an adju~tment IS
reached. Also fla5he~ If you press the adjustment buttons
on the front panel In the Lock mode.
m t:> power switch and indICator
Turns the momtor on and off. The indicator illuminates
when the monitor IS turned on.
To disconnect
the power completely, unplug the power
cord.
[ID AC IN connector (page 6)
input for the ~upphed AC power cord
(ID Video mput connectors (5 BNC) (page 6)
Accept ReB vldt;O'o and sync :'Ignab
BNC
Input onnntorsl R
_:l~ll3b (@)
SYnc on
l.rl:'"t'n
H/V
Composite
Sync
R<d
Red
G B
(@)
(@)
C0m~t~ I Blue
~yn( nn
Gr ... t'ro
Crt>t:'n I Slut'
HO
(@)
H/V
Cumpo>llt
Svnc
vo
(@)
HjV
s.-p.uale
S~'nc
Red Grt:'l;'n ! Blut' H Sync IV
Sync
llil 8:-JC/O-SUB ;witch (p"ge 6)
Select::. the RGB or O-sub Signal
l __ ~'
[j] Video input connector OS-pin mini D-sub) (page 6)
Accepts D-sub Video and sync signals. To connect this
connector, use the supplied IS-pin mini D-sub cable.
o o
Pm,\iu !
Signal
Signal
Red
N/C
Green
Ground
(Cump..>Slte
Sync on Green)
Slue
Ground
Ground
Bi-Due-ctlonal D.lta
(SDA)'
DOC Ground· !3 H. Sync
Red Ground 14
V. Sync
Green Ground
tS
Data Clock (5CU·
Blue Ground
• DIsplay Data Channd (DOC) Standard by VESA
~ 7S0/2kO SWitch
SWitches
the impedance of the sync input connectors
«(ID, [j]) termindtion to 75 n or 2 kn. ThiS monitor is
Lnltially set to 2 kfl, whICh LS appropn<\te for the majonty
of IBM compatible .md Maclnto!>h systems. For UllIlllH!
systems which may require 75ft ~et' the Oper .. lllng
In~tructions ot your computer.
[j] CONTROL LOCK switch
Locks the montlor so that the buttons, except the power
SWitch, on the front panel cannot be operated (Lock
mode) With this switch, you can ensure that the display
remainS In the optimum condition even when the
mom tor is placed where the control buttons can be
touched by unauthorized persons.
To release the Lock mode, set to OFF
I\!ormally keep this switch set to OFF.
[j1J SERVICE terminal
The term mal is to be used by servICe personnel only.
.,
5

en
I
Connection
You (,In connect this mOnitor to imy IBM or compatible system, Macintosh, and othH various computers. In order to comply
with the mandatory FCC standards, use the supplied Video signal cablt'.
Connecting an IBM or compatible system
CSt' the supplied video Signal cable.
Set to D-SUB.
Toawa~et ~ II 111~ci l·f·':: .. ~1111 III
BNC c=m O·SUB
.........
Power cord (supplied)
To video output
~
Video signal (able (supplied)
Connecting a Macintosh system
Use the supplied video signal cable, and d MaCintosh adapter (not supplied).
Set to D-SUB.
To a wall outlet
+- ~ 1'1 ttrn~IU
Power cord (SUPPlied: I \
Connecting a computer to the BNC connector
Use it BNC video signal cable (not supplied) Set to BNC.
Toawal~t ~ II 1,5.1111 II rBNemlDsuB1
Power cord (supplied)
Computer
I~~Q£JI
To video output
Video signal cable (not supplied)
6 F
~"!
Attaching the ferrite cores
Wht:'n you use a Video signal cable otiWf Ih,1I1 the ~uppllL'J
one, be sure to dtt,Kh the supplied terntl' core ,l~ dlll~trdted
Close the lid.
~
~
Pull the supplied plastic binder tightly.
~
~~
-~-~" 1l-~1
Preset Mode
The Multiscan 205h autoillatically ad!ll~b the J.l~pl<ly ~ize
.lnd POSition to the optimum 1Il J((ordann: \'11th the Input
Signal up to l~ Jltfert:'nt types.
[t has factory-presd adjustment dato for 9 Jlfferent types of
~ignab (preset mode). When a computer or it \ .... orkstation
No. Display Horizontal
(dots x lines)
frequency
I 640 x 480 31.5
kill
--
2 800 x 600 46.9
kllz
3 832 x 624
497kHz
4 1024 x 768 60.2
kHz
5 1152 x 870 68.7
kHz
6 1280 x
\024
80 0 kHz
_7_
1600 x 1200 93.6
kHz
I-----~~~-
I
8 1600 x 1200 100
kHz
9 1600 x 1200 106.3
kHz
I
-
l)VGA I~ d tr,ldemMb nf lUr-..t Cnrporat!on
2)VESA i~ ,I tr,ldl'm,lrl-.ul tilt.' Illln-pmfit llrg,lIl1L,ltHlll, VIdeo
Electrolllc~ Stcll1d,1rd r\~Sl)(l<lt\On
3)r-.tacI!Ho~h l~ ,I Ir,lliL'marl-. ()f Applt' Compukr [nc
Em
• Tht' button~ nil the tront panel ,III<H\' IlMlllldl iHijustnwnt
\\·hen ,1 "'1~n .... 1 tWin l'qulpnH'nt uther 111,111 the pre~et·type
HHH.it'b.,.; mput \;inL' dllterl'lIt m,lnu,llly ,1Jju~tl;.'d d,lta
.HI..' ~tllrl'd in 1lH"II\llrv, ,1nd LlllL'd b.l~l.. when the '>,lnlL'
:::OlMI1,lll:::O Input ,1g,lIn:::oo th,lt tilt., Opltll1Ul\1 dl:>plav lor thl~
'>1 t; 11 ,1 I I." ,)bt,lllll'd ,lut{ltn,IIIl,llly
mn1
If you do not att,Kh the h~rnte core, the monitor
will not (ontorm 10 manJatory FCC st,lIldarJ."
that Issues :::ouch ~lgnal I::. connected, thl! optimum dbplay IS
obtained without any manual adjustment .
The factory-preset adjustment data are listed below:
Vertical Graphics
mode
frequency
Iilliz
YGA GraphiC 1)
75 Hz
YESA2)
75 Hz
Macmtosh 16" color)) I
75 Hz
M,Kinto~h 19" color
75 Hz
Macmtosh 21" color
75 Hz
VESA
75 Hz
VESA
80Hz
1
VESA
85 Hz
I
VESA
• The type ot Input vldeu Signal is dlstlnguisht:'d according
to its ~ignal ::.peClficatlOns, such.1s horizontal frequency or
::.ync polaflty. When the Signal specitications 01 the mput
::.!gnaJs iHe almost same, these signals may not be
dIStingUished ,l~ bemg different.
• If \fOll use a computer or vH.iea board of high output level
(,lbullt 1.0 Yp-pl, you may not bt' able to obtam the
optimum display. In such case, try decre,\sing the pICture
(Ulltr""t (p,lge H)
7

SECTION 2
DISASSEMBL
Y
GDM-20SHT
2-1. REAR CABINET AND TOP COVER REMOVAL
2-2. D BLOCK ASSY REMOVAL
CD Five screws
(-t-BVTP M4 x 8)
CD Four screws
(+BVTP 4 x 16)
CD Rea' cablnel j
~/~
,. ,
~
®Two screws
(+-BVTP M4 x 8)
!J) Rear shield
I
)
CD Two push rivets
!J) Two screws
(+-BVTP M3 x 8)
\ @Two PCB holde'
,.1
CD Screw j Push
(+--BVTP M4 ,81 ~ ~
CD Four screws
(-t-BVTP M4 x 8)
-7-
CD 0 block assy
(Remove the twelve connectors,
CN401-404, 406-411, FV1, FV2)

GDM-20SHT
2-3. POWER BLOCK ASSY REMOVAL
IJ) Top shield
""Q
,
CD Two PCB holder
CD Four screws
G)Twoclaws
CD Power block assy (+-BVTP M4 x 8)
(Remove the three connectors
CN603, 605, 606)
2-4. L BOARD REMOVAL
G) L board
~~d--t~CD Two claws
-8-

2-5. M BOARD REMOVAL
2-6. A BLOCK ASSY REMOVAL
FV1
Earth lead CN101
@M board
CD Two screws
.
~ (-t-BVTP M4 x 8)
~:?"\
1
CD Two screws
(+-BVTP
M3 x 8)
CD Two screws
(+-BVTP 3 x 12)
CD Video shield cover
CN104
)~
" CN102
CD A block assy
(Remove the eleven connectors,
GDM-20SHT
CN1 01-104, J1 01-301, FV1, FV2, NTC, Earth lead)
(DScrew
(Hexagon head screw M4 x 20)
-9-

GDM-20SHT
IDBI
[8J
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
RESISTOR
D901 8·719-045-19 DIODE SPB-26MVWF
D902 8-719-311-90 DIODE SEL1922D-C
Rl0l
1-216-073-00 METAL GLAZE 10K 5%
WOW
D903 <4-049-089-01 HOLDER, LED
Rl02
1-208-806-11 METAL CHIP 10K
0.50%1/10W
0903
8-719-311-90 DIODE SEL1922D-C
Rl03
1-218-768-11 METAL CHIP 470K
0.50%1/10W
Rl04
1-218-760-11 METAL CHIP 220K
0.50%1/10W
0904
8-719-311-90 DIODE SEL1922D-C
Rl05
1-216-649-11 METAL CHIP 820
0.50%1/10W
D905 8-719-311-90 DIODE SEL1922D-C
0906 8-719-311-90 DIODE SEL1922D-C
Rl06
1-216-663-11 METAL CHIP 3.3K
0.50%1/10W
0907 8-719-311-90 DIODE SEL1922D'C
Rl07 1-216-057-00 METAL GLAZE 2.2K 5%
1/10W
0908
8-719-911-19 DIODE lSSl19-25
Rl08
1-216-073-00 METAL GLAZE 10K 5%
1/10W
Rl09
1-216-627-11 METAL CHIP 100
0.50%1/10W
D909 8-719-911-19 DIODE
lSSl19-25
Rll0
1-216-049-91 METAL GLAZE
lK 5%
1/10W
D910 8-719-911-19 DIODE lSS119-25
D911
8-719-911·19 DIODE lSS119-25
Rlll
1-216-049-91 METAL GLAZE
lK 5%
1/10W
0912 8-719-311·90 DIODE SEL1922D-C
R112 1-216-049-91 METAL GLAZE
lK 5%
1/10W
0913 8-719-109·85 DIODE
RD5.1 ESB2
R113 1-249-887-11 CARBON 33 5%
1/4W F
R114 1-208-806-11 METAL CHIP 10K
0.50%1/10W
0914 8-719-109-85 DIODE RD5.1 ESB2
R115 1-208-814-11 METAL CHIP 22K
0.50%1/10W
0915 8-719-109-85 DIODE RD5.1 ESB2
D916 8-719-109-85 DIODE RD5.1ESB2
Rl16
1-208-814-11 METAL CHIP 22K
0.50%1/10W
D917 8-719-109-85 DIODE RD5.1 ESB2
Rl17 1-208-e06-11 METAL CHIP 10K
0.50%1/10W
0918 8-719-109-85 DIODE
RD5.1 ESB2
R118 1-216-057-00 METAL GLAZE 2.2K 5%
1/10W
R119 1-216-627-11 METAL CHIP 100
0.50%1/10W
D919 8·719-109-85 DIODE RD5.1 ESB2
R123 1-249-437·11 CARBON 47K 5%
1/4W 0920 8-719-911-19 DIODE lSS119-25
0921 8-719-911-19 DIODE
lSSl19-25
R124 1-249-437-11 CARBON 47K 5%
1/4W
0922
8-719-911-19 DIODE lSSl19-25
R126 1-208-854-11 METAL CHIP
1M
0.50%1/10W
D923 8-719-911-19 DIODE lSS119-25
R130 1-208-806-11 METAL CHIP 10K
0.50%1/10W
0924 8-719-311-90 DIODE SEL1922D-C
1rw ............. , ................................................................. 1I''Ir* .............. ."." ... .",., ....... 11' ...... ."." • ."11'11',,, .........
IC
H BOARD
IC931 8-759-285-18 IC MC68HC05P7BSC402191 B
........................... -IC932 8-759-165-81 IC PST600D-T
(BOARD PART NO. 1-657-355-11)
4-045-133-01 HOLDER (B), LED COIL
L901
1-410-482-31 INDUCTOR 100UH
CAPACITOR
C904 1-102-114-00 CERAMIC 470PF 10% 50V TRANSISTOR
-. C905 1-102-114-00 CERAMIC 470PF 10% 50V
-. C906 1-102-114-00 CERAMIC 470PF 10% 50V 0931 8-729-900-36 TRANSISTOR DTC124ES
C907 1-102-114-00 CERAMIC 470PF 10% 50V
0932
8-729-902-80 TRANSISTOR DTA114YS
C931
1-128-057-11 ELECT 330MF 20% 6.3V
0933
8-729-902-80 TRANSISTOR DTA114YS
C932 1-161-051-00 CERAMIC O.OlMF 10% 50V
C933 1-126-160-11 ELECT
lMF
20% 50V RESISTOR
C945 1-136-165-00 FILM O.lMF 5% 50V
C990 1-136-153-00 FILM
O.Q1MF
5% 50V
R901
1-247-807-31 CARBON 100 5%
1/4W
C991
1-136-153-00 FILM
O.Q1MF
5% 50V R902 1-247-807-31 CARBON 100 5% 1/4W
R903 1-247-807-31 CARBON 100 5%
1/4W
C992 1-136-153-00 FILM O.OlMF 5% 50V R904 1-247-807-31 CARBON 100 5% 1I4W
C993 1-136-153-00 FILM O.OlMF 5% 50V R905 1-247-807-31 CARBON 100 5%
1/4W
R906 1-249-423-11 CARBON 3.3K 5%
1/4W
CONNECTOR R907 1-247-807-31 CARBON 100 5%
1/4W
R908 1-249-425-11 CARBON 4.7K 5%
1/4W
CN901<1-564-525-11 PLUG, CONNECTOR lOP R909 1-249-425-11 CARBON 4.7K 5%
1/4W
R910 1-249-425-11 CARBON 4.7K 5% 1/4W
DIODE
R911
1-249-425-11 CARBON 4.7K 5%
1/4W
R912 1-247-807-31 CARBON 100 5%
1/4W'
.
.
"-
0901 <4-049-089-01 HOLDER. LED R913 1-247-807-31 CARBON 100 5% 1/4W
-76 -