Sony SDM-HS74P User manual

MENU
OK
COLOR MONITOR
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS NO. : CL-42
FACTORY MODEL: LHS74P, LHS74PM
MODEL: SDM-HS74, SDM-HS74P

1. LCD CHARACTERISTICS
Type : TFT Color LCD Module
Active Display Area : 17 inch(337.92(H) x 270.336(V))
Size : 358.5(W) x 296.5(H) x 17.0(D)
Pixel Pitch : 0.264 (Per one triad) x 0.264
Color Depth : 16.2M Colors
Electrical Interface : LVDS
Operating Mode : Normally White
Backlight Unit : 4-CCFL (Cold Cathode
Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥ 10
Left : -60° min., -70°(Typ) Right : +60° min., +70°(Typ)
Top :+60° min., +70°(Typ) Bottom : -60°min., -70°(Typ)
2-2. Luminance : 75(min), 80(Typ)
2-3. Contrast Ratio : 250(min), 450(Typ)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
• Type : Separate Sync
3-2. Video Input Signal
1) Type : R, G, B Analog
2) Voltage Level : 0~0.70 V( 5%)
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.35 Vp-p
c) Color 15, 0 : 0.7 Vp-p
3) Input Impedance : 75 Ω
3-3. Operating Frequency
Horizontal : 28 ~ 80kHz
Vertical : 48 ~ 75Hz
4
. Max. Resolution
Analog : 1280 x 1024 / 75Hz
Digital : 1280 x 1024 / 60Hz
5. POWER SUPPLY
5-1. Power
: AC 100~240V, 50/60Hz , 1.0A
5-2. Power Consumption
6. ENVIRONMENT
6-1. Operating Temperature: 5°C~35°C (41°F~95°F)
(Ambient)
6-2. Relative Humidity : 10%~80%
(Non-condensing)
6-3. MTBF : 50,000 Hours(Typ)
30,000 Hours(Min)
7. DIMENSIONS (with TILT/SWIVEL)
Width : 367 mm (14.49'')
Depth : 215 mm (8.46'')
Height : 410 mm (16.14'')
8. WEIGHT (with TILT/SWIVEL)
Net. Weight : 5.7 kg (12.57 lbs)
Gross Weight : 8.3 kg (18.30 lbs)
CONTENTS
SPECIFICATIONS
- 2 -
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 3
TIMING CHART ........................................................4
OPERATING INSTRUCTIONS ................................ 5
WIRING DIAGRAM ................................................. 6
BLOCK DIAGRAM ................................................... 7
DESCRIPTION OF BLOCK DIAGRAM.....................8
ADJUSTMENT ...................................................... 10
TROUBLESHOOTING GUIDE .............................. 11
EXPLODED VIEW...................................................17
REPLACEMENT PARTS LIST ...............................19
SCHEMATIC DIAGRAM......................................... 22
MODE
POWER ON (NORMAL)
STAND-BY
SUSPEND
DPMS OFF
POWER S/W OFF
H/V SYNC
ON/ON
OFF/ON
ON/OFF
OFF/OFF
-
POWER CONSUMPTION
less than 45 W
less than 1 W
less than 1 W
less than 1 W
LED COLOR
GREEN
AMBER
AMBER
AMBER
OFF
VIDEO
ACTIVE
OFF
OFF
OFF
-less than 1 W

- 3 -
Signal Connector Pin Assignment
Pin Signal (DVI-D)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
T. M. D. S. Data2-
T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4-
T. M. D. S. Data4+
DDC Clock
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1-
T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3-
T. M. D. S. Data3+
+5V Power
Ground
(return for +5V,
H. Sync. and V. Sync.)
Pin Signal (DVI-D)
18
9
17 24
16
16
17
18
19
20
21
22
23
24
Hot Plug Detect
T. M. D. S. Data0-
T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5-
T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
T. M. D. S. (Transition Minimized Differential Signaling)
• DVI-D Connector

- 4 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
•There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
•Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
•Must mount the module using mounting holes arranged
in four corners.
•Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
•Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
•Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
•Make certain that treatment person’s body are
grounded through wrist band.
•Do not leave the module in high temperature and in
areas of high humidity for a long time.
•The module not be exposed to the direct sunlight.
•Avoid contact with water as it may a short circuit within
the module.
•If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
•If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
•Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
PRECAUTION
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

- 5 -
Mode H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
720x400
70Hz
H–35.00 864 640 64 64 96 224
V–66.667Hz 525 480 3 3 39 45
640x480
60Hz
H–37.50 840 640 16 64 120 200
V–75.0Hz 500 480 1 3 16 20
640x480
65Hz
H–31.500 900 720 18 108 54 180
V + 70.156Hz 449 400 12 3 34 49
640x480
75Hz
H–35.162 896 720 34 40 102 176
V–59.901Hz 587 480 12 2 93 107 720x480
60Hz
H +- 35.156 1024 800 24 72 128 224
V + 56.250Hz 625 600 1 2 22 25 800x600
56Hz
H + 37.879 1056 800 40 128 88 256
V + 60.317Hz 628 600 1 4 23 28 800x600
60Hz
H + 48.077 1040 800 56 120 64 240
V + 72.188Hz 666 600 37 6 23 66 800x600
72Hz
H + 46.875 1056 800 16 80 160 256
V + 75.0Hz 625 600 1 3 21 25 800x600
75Hz
H–49.727 1152 832 32 64 224 320
V–74.553Hz 667 624 3 3 37 43
832x624
(MAC16”)
75Hz
H–48.363 1344 1024 24 136 160 320
V–60.004Hz 806 768 3 6 29 38 1024x768
60Hz
H–56.476 1328 1024 24 136 144 304
V–70.069Hz 806 768 3 6 29 38 1024x768
70Hz
H + 60.023 1312 1024 16 96 176 288
V + 75.029Hz 800 768 1 3 28 32 1024x768
75Hz
H–60.241 1328 1024 32 96 176 304
V–74.927Hz 804 768 3 3 30 36
1024x768
(MAC19)
75Hz
H + 67.500 1600 1152 64 128 256 448
V + 75.000Hz 900 864 1 3 32 36 1152x864
75Hz
H–68.681 1456 1152 32 128 144 304
V–75.062Hz 915 870 3 3 39 45
1152x870
(MAC21)
75Hz
H–61.795 1504 1152 30 128 194 352
V–65.950Hz 937 900 2 4 31 37 1152x900
66Hz
H–71.732 1472 1152 16 96 208 320
V–76.068Hz 943 900 2 8 33 43 1152x900
75Hz
H + 31.216 1480 1170 37 129 144 310
V + 50.026Hz 624 584 3 3 34 40 1170x584
50Hz
H + 60.000 1800 1280 96 112 312 520
V + 60.000Hz 1000 960 1 3 36 40 1280x960
60Hz
H + 63.981 1688 1280 48 112 248 408
V + 60.020Hz 1066 1024 1 3 38 42 1280x1024
60Hz
H + 79.976 1688 1280 16 144 248 408
V + 75.025Hz 1066 1024 1 3 38 42 1280x1024
75Hz
Sync
Polarity Frequency
Dot
Clock
Back Porch
(F)
Blanking time
(B)
Resolution
28.350
25.175
30.240
31.500
31.505
36.000
40.000
50.000
49.500
57.285
65.000
75.000
78.750
80.000
108.000
100.000
92.940
105.590
46.200
108.000
108.000
135.000
TIMING CHART
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H–31.469 800 640 16 96 48 160
V–59.940Hz 525 480 10 2 33 45
Sync Duration
(D)
Front Porch
(C)
Video Active Time
(A)
Total Period
(E)

TIMING CHART
- 6 -
VIDEO
SYNC
B
C
EA
D
OPERATING INSTRUCTIONS
FRONT / REAR VIEW
1. (Power) switch and indicator
To turn the display on or off, press the (power) switch
upward.
The power indicator lights up in green when the display
is turned on, and lights up in orange when the monitor is
in power saving mode.
2. MENU button
This button displays or closes the main menu.
3. buttons
These buttons function as the buttons when
selecting the menu items and making adjustments.
4. OK button
This button selects the item or executes the settings in
the menu.
5. button
This button is used to change the brightness of the
screen.
6. AC IN connector
Connect the power cord (supplied).
7. DVI-D input connector (digital RGB)
This connector inputs digital RGB video signals that
comply with DVI Rev.1.0.
8. HD15 (RGB) input connector (analog RGB)
This connector inputs analog RGB video signals (0.7
Vp-p, positive) and SYNC signals. DDC (Display Data
Channel) is a standard of VESA.

- 7 -
WIRING DIAGRAM
Connector Ass’y
P/N: 6631T11016W
Connector Ass’y
P/N: 6631T20023L

- 8 -
ADC
DVI(TMDS)
Inverter
Output
(4Lamp)
EEPROM
(EDID)
EEPROM
(System)
LVDS
Panel
Vcc
Regulator Regulator
KEY
DVI-D D-Sub X1
Filter
EEPROM*1
(EDID) MST9131B
3.3V
3.3V
2.5V
2.5V
5V
5V
MTV412PLCC
12V
DVI Rx
LAMP Connector
LIPS
OSD
Scaling Pre-Amp PLL
LVDS
Tx
+
BLOCK DIAGRAM

- 9 -
DESCRIPTION OF BLOCK DIAGRAM
1. Video Controller Part & Display Data Transmitter Part.
This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the
digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 135MHz.
This part consists of the Scaler, LVDS Tx, TMDS Rx, Reset IC.
The Scaler gets the video signals which were converted analog to digital, interpolates input to 1280 x 1024
resolution signal and outputs 8-bit R, G, B signal to transmitter.
Especially pre-amp / ADC / Video controller/ Transmitter are merged to one chip ‘MST9131A’by MST.
This part transmit digital signal from the Scaler to the receiver of module.
2. Power Part
This part consists of the one 3.3V and one 2.5 regulators to convert power which is provided 5V by LIPS Board.
In particular, 5V is provided for LCD Panel. There is also 12V which is for Audio power.
Also, 5V is converted 3.3V and 2.5V by regulator. Converted power is provided for IC in the main board.
3. System Controller (Microprocessor) Circuit
1) Microprocessor (U501) distinguishes polarity and frequency by calculating horizontal and vertical sync input from
signal source.
2) Microprocessor (U501) carries out power control by sending power-down trigger signal to each IC.
3) Microprocessor (U501) communicates with EEPROM (704), and MST9131A (U201) through IIC or 8 bit bus line.
It is enable to control and communicate each devices.
4) Microprocessor (U501) let User adjust screen by OSD function.

- 10 -
EMI
COMPONENTS
LINE
100 ~ 240V
INPUT RECTIFIER
AND FILTER ENERGY TRANSFER OUTPUT RECTIFIER AND FILTER
12V
5V
GND
SIGNAL
COLLECTI
ON
PHOTO-
COUPLER
ISOLATION
PWM
CONTROL
CIRCUIT
HVDC 100KHz
PRIMARY SECONDARY
50 ~ 60Hz
Operation description_LIPS
LIPS Board Block Diagram
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and also
the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor.

- 11 -
ADJUSTMENT
Windows EDID V1.0 User Manual
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Doesn’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available for LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys”file to
“c:\WINNT\system32\drivers”folder
b) Run Userport.exe
c) Remove all default number
d) Add 300-3FF
e) Click Start button.
f) Click Exit button.
2. EDID Read & Write
1) Run WinEDID.exe
2) Edit Week of Manufacture, Year of Manufacture,
Serial Number
a) Input User Info Data
b) Click “Update”button
c) Click “Write”button

- 12 -
Figure 1. Cable Connection
220
IBM
Compatible PC
PARALLEL PORT
Power inlet (required)
Power LED
ST Switch
Power Select Switch
(110V/220V)
Control Line
Not used
RS232C
PARALLEL
V-SYNC POWER
ST
VGS MONITOR
E
E
V-Sync On/Off Switch
(Switch must be ON.)
F
F
A
A
B
B
C
C
1510
5
569
1
1
1
14
13
25
6
5V
5V
5V
4.7K
4.7K
4.7K
74LS06
74LS06
OFF ON
OFF
ON
11
Video Signal
Generator
SERVICE OSD
1) Turn off the power switch button.
2) Press DOWN, POWER key.
3) Shows the service OSD menu. That menu is located in down side of main menu.
4) The service OSD menu contains additional menus as described below.
a) COLOR TEMP : Adjust R/G/B color values of contrast and brightness in 9300K, 6500K, user color mode.
b) INITIAL EEPROM : Initialize the EEPROM values(24C08).
c) CLEAR ETI : Initialize the used time of monitor.
d) AGING : Select aging mode.(On/Off)
e) WHITE BALANCE
AUTO : Allows you to set the R/G/B offset and gain value automatically.
MANUAL : Allows you to set the R/G/B offset and gain value manually.
f) DEFAULT TIMING : Select the resolution timing of the signal. Sub menus are 1152x864(VESA standard
timing) and 1152x870(MAC computer timing).
g) MODULE : Select the LCD module attached to this monitor.

- 13 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO PROBLEM
NO POWER
(POWER INDICATOR OFF)
CHECK POWER
BOARD, AND FIND
OUT A SHORT POINT
AS OPENING
EACH POWER LINE
CHECK J705
VOLTAGE
PIN 5, 6, 8(5V)
PIN 1, 2(12V)?
NO
CHECK 5VS LINE
(OPEN CHECK)
CHECK
U501 PIN 8 Voltage
(5V) ?
NO
CHECK IIC LINE
CONNECTION
(U501, U502)
CHECK U201 VCC,
X501 XTAL CHECK
IS U201
PIN94 (3.3V), PIN85(2.5V)
VOLTAGE REPEATED
AS PULSE
SHAPE ?
NO
YES
YES NO PROBLEM
YES
CHECK KEY CONTROL
CONNECTOR ROUTINE

- 14 -
2. NO RASTER
CHECK MICOM INV
ON/OFF PORT.
CHECK
J705 PIN 9
5V?
NO
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK LIPS
CHECK J705
PIN 5, 6, 8(5V)
PIN 1, 2(12V)?
NO
1. CONFIRM BRIGHTNESS
OSD CONTRL STATE.
2. CHECK MICOM DIM-ADJ
PORT
CHECK
J705 PIN 10
5V?
NO
LIPS
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL.
(CONTACT PROBE TO
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
NO
REPLACE CCFL LAMP
IN THE LCD MODULE
YES
YES
YES
YES

- 15 -
1. CHECK PIN11, 12
SOLDERING CONDITION
2. CHECK X501
3. TROUBLE IN U501
U201
POWER PIN 72,
82, 94(3.3V)
PIN 64, 85 (2.5V)?
NO CHECK U803
(2.5V REGULATOR),
CHECK U804
(3.3V REGULATOR)
U501
PIN11, 12
OSCILLATE AS
12MHZ?
CHECK CONNECTION LINE
FROM D-SUB TO U501
TROUBLE IN CABLE
OR LCD MODULE
YES
YES
YES
3. NO RASTER (OSD IS NOT DISPLAYED) –MST9131B
NO RASTER
(OSD IS NOT DISPLAYED)
U501
PIN41 IS 48KHz H-SYNC?
PIN42 IS 60Hz V-SYNC?
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
NO
NO

- 16 -
4. TROUBLE IN DPM
TROUBLE IN DPM
TROUBLE IN PC
CHECK PC
PC IS NOT GOING
INTO DPM OFF MODE
NO
TROUBLE IN
SIGNAL CABLE
NO
YES
YES
CHECK
R734, R741
(INPUT-1)SYNC.
R732, R755
(INPUT-2)SYNC.
CHECK
U501 PIN 24
(0V) ?

- 17 -
12
GENESS
SONY
1
2
3
13
9
11
16
7
10 15
8
6
5
14
4-1
4-2
EXPLODED VIEW

- 18 -
EXPLODED VIEW PARTS LIST
1
2
3
4-1
4-2
5
6
7
8
9
10
11
12
13
14
15
16
3091TKL061K CABINET ASSEMBLY, HS94 SONY 3090TKL061A BLUE - Europe, U.S.A/CANADA-SDM-HS74
3091TKL061L
CABINET ASSEMBLY, HS74 SONY 3090TKL061A BLACK - U.S.A/CANADA-SDM-HS74, SDM-HS74P
3091TKL061N CABINET ASSEMBLY, HS74P SONY 3090TKL061A BLACK SPRAY - Europe, Japan - SDM-HS74P
3091TKL061M
CABINET ASSEMBLY, HS74P SONY 3090TKL061A SILVER SPRAY - Europe, Japan,U.S.A/CANADA-SDM-HS74P
6304FCI005B LCD(LIQUID CRYSTAL DISPLAY), M170E5-L05 CHIMEI TFT COLOR 300NITS 16MS TCO-03 TN SXGA - Europe-SDM-HS74
6304FAU012A LCD(LIQUID CRYSTAL DISPLAY), M170EN05V5 AU TFT COLOR SXGA 250NIT GEN5-Europe, U.S.A/CANADA-SDM-HS74
6304FAU010B
LCD(LIQUID CRYSTAL DISPLAY), M170EN06-V2(AR COATING), AU TFT COLOR LVDS SXGA 16MS - SDM-HS74P
3809TKL085C BACK COVER ASSEMBLY, HS74 3808TKL084A BLACK-SDM-HS74P, U.S.A/CANADA-SDM-HS74
3809TKL085B BACK COVER ASSEMBLY, HS74 3808TKL084A DARK BLUE -SDM-HS74
3043TKK109A TILT SWIVEL ASSEMBLY, SONY_HS17 . . - SDM-HS74
3043TKK109C TILT SWIVEL ASSEMBLY, SONY HS74P . .- SDM-HS74P
3043TKK115B TILT SWIVEL ASSEMBLY, HS74 3550TKK304C _NT - SDM-HS74
3043TKK115C TILT SWIVEL ASSEMBLY, HS74P 3550TKK304C .- SDM-HS74P
6871TST540B PWB(PCB) ASSEMBLY,SUB, LHS74/94(P)M CONTROL TOTAL SONY CL-55
4951TKS165B METAL ASSEMBLY, FRAME HS74 CMO_L05 - SDM-HS74
4951TKS165A METAL ASSEMBLY, FRAME HS74 AUO_V5 - SDM-HS74
4951TKS165D METAL ASSEMBLY, FRAME HS74 AUO EN06 V2 - SDM-HS74P
4950TKK583A METAL, FIX CONNECTOR CMO 17 OX73
4950TKK487A METAL, FIX CONNECTOR-AU SIDE LS71K
3550TKK301B COVER, LHS73K PIECE BACK DARK BLUE - SDM-HS74
3550TKK301G COVER, LHS73K PIECE BACK BLACK - SDM-HS74(USA/CANADA), SDM-HS74P
6631T11016W CONNECTOR ASSEMBLY, 30P-30P H-H 200MM UL20276 AWG30 LOX73L/LOX93L
6871TPT285C PWB(PCB) ASSEMBLY,POWER, HS74 CMO, HS94 LPL/AUO POWER TOTAL POWERNET
6871TPT285A PWB(PCB) ASSEMBLY,POWER, HS74 AUO 2X4PIN POWER TOTAL POWERNET
3313TL7047B MAIN TOTAL ASSEMBLY, LHS74M - AGRDR SONY CL-43 - SDM-HS74 , CMO
3313TL7047A MAIN TOTAL ASSEMBLY, LHS74/94PM _ AUO SONY CL-42 - SDM-HS74
3313TL7047E MAIN TOTAL ASSEMBLY, LHS74PM AURDR SONY CL-42 - SDM-HS74P, AUO
4815TKK040A SHIELD ASSEMBLY, REAR HS74
3550TKK302L COVER, HS74 BACK DECO BLUE- SDM-HS74
3550TKK302M COVER, HS74 BACK DECO BLACK- U.S.A/CANADA-SDM-HS74
- 3550TKK302P COVER, HS74P BACK DECO BLACK SPRAY - Europe, Japan-SDM-HS74P
3550TKK302N COVER, HS74P BACK DECO SILVER SPRAY- Europe, Japan, U.S.A/CANADA-SDM-HS74P
3550TKK302Q COVER, HS74P BACK DECO BLACK- U.S.A/CANADA-SDM-HS74P
3846TKK058B MARK, PIECE BADGE(AL),SONY-HS73-BK(3-704-176-51)
3846TKK062B MARK, PIECE BADGE SONY NO6.0(AL) 4-095-995-21 GREY
6620K00002G
SOCKET(CIRC),POWER, HUAJIE,SA-4S-008-2-AA(180MM),JST,17" SONY AC UNIVERSAL NOPIN BLACK
6631T20023L CONNECTOR ASSEMBLY, 11P-11P H-H 160MM UL1061 AWG26 TWI LOS93L (JST HOUSING)
Description Part No.
Ref. No.

- 19 -
DATE: 2004. 06. 02.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C204 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C205 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C206 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C207 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C208 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C209 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C210 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C211 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C213 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C214 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C215 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C216 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C217 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C218 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C219 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C220 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C221 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C222 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C223 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C224 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C225 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C226 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C227 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C230 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C231 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C232 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C233 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C240 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C251 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C500 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C501 0CZZTAT006A RV2-16V100MU-R ELNA 16V 10UF
C502 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C503 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C504 0CC330CK41A 33PF 1608 50V 5% R/TP NP0
C505 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C506 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C512 0CC180CK41A 18PF 1608 50V 5% R/TP NP0
C513 0CC100CK41A 10PF 1608 50V 5% R/TP NP0
C516 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C703 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C707 0CC680CK41A 68PF 1608 50V 5% R/TP NP0
C708 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C709 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C710 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C711 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C712 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C713 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C714 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C727 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C730 0CC101CK41A 100PF 1608 50V 5% R/TP NP0
C731 0CC680CK41A 68PF 1608 50V 5% R/TP NP0
C732 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
DATE: 2004. 06. 02.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C733 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C734 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C735 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C737 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C738 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C739 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C740 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C745 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C746 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C747 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C760 0CZZTAT005B RJ4-16V101MX ELNA 16V 100UF 2
C761 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C762 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C801 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C802 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C803 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C804 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C809 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C810 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C817 0CZZTAT005B RJ4-16V101MX ELNA 16V 100UF 2
C818 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C819 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C820 0CZZTAT005B RJ4-16V101MX ELNA 16V 100UF 2
C821 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C822 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C823 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C828 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
C829 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C831 0CZZTAT005B RJ4-16V101MX ELNA 16V 100UF 2
C832 0CZZTAT005B RJ4-16V101MX ELNA 16V 100UF 2
D701 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D702 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D706 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D707 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23
D708 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D709 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D710 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D711 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D712 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D713 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D714 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D715 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D719 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23
D720 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D721 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D722 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D723 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D724 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D725 0DS226009AA KDS226 TP KEC SOT-23 80V 300
D726 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23
D727 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
MAIN BOARD
CAPACITORS
DIODEs

DATE: 2004. 06. 02.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
ZD501 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD502 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD701 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD702 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD703 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD704 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD705 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD706 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD709 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD711 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD715 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD716 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD719 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD720 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD721 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
ZD722 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323
U201 0IPRPM3011C "MST9131B-LF MSTAR 128P,LQFP T"
U502 0IMMRSS040C S524A60X51(SCT0) SAMSUNG ELEC
U702 0IMMRSG036A "M24C02-WMN6T SGS-THOMSON 8P,S"
U703 0IMMRSG036A "M24C02-WMN6T SGS-THOMSON 8P,S"
U802 0TFVI80023A VISHAY SI3865DV R/TP TSOP-6 8
U803 0IPMGFA003E FAN1086-1.5A FAIRCHILD SOT252
U804 0IPMGK2001B AIC1117A-33CYTR(BS33) AIC SOT
L801 6210TCE001S HU-1M2012-121 CERATECH 2012MM
L802 6210TCE001S HU-1M2012-121 CERATECH 2012MM
L803 6210TCE001S HU-1M2012-121 CERATECH 2012MM
Q502 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q503 0IKE704200H KIA7042AP TO-92 TP 4.2 VOLT.
Q504 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q505 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q506 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q701 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q702 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q703 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q704 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
R201 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R202 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R203 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R207 0RJ3900D677 390 OHM 1/10 W 5% 1608 R/TP
R208 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R209 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R210 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R220 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R240 0RJ3900D677 390 OHM 1/10 W 5% 1608 R/TP
R501 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R502 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R503 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R504 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R505 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R507 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
DATE: 2004. 06. 02.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R508 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R509 0RH4701D622 4.7K 1/10W 5 D.R/TP
R510 0RH4701D622 4.7K 1/10W 5 D.R/TP
R514 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R517 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R518 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R519 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R520 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R521 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R522 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R523 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R524 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R525 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R526 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R527 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R532 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R533 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R534 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R535 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R537 0RH4701D622 4.7K 1/10W 5 D.R/TP
R541 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R544 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R545 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R551 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R570 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R571 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R572 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R573 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R574 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R575 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R576 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R577 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R582 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R584 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R585 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R586 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R587 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R588 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R589 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R590 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R591 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R592 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R593 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R594 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R595 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R701 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R703 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R705 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R706 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R707 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R708 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R709 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R710 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R711 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R716 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R717 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R722 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R723 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R724 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R726 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R727 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R728 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP
- 20 -
TRANSISTOR
RESISTORs
COILs & COREs
ICs