Sony SRX-R515P User manual

DIGITAL CINEMA PROJECTOR PACKAGE
SRX-R515P
LENS CHANGE TABLE
LKRA-008
3D PROJECTION LENS
LKRL-A502
LKRL-A503
2D PROJECTION LENS
LKRL-Z511
LKRL-Z514
LKRL-Z519
PROJECTION LAMP
LKRM-U330
LKRM-U450
INSTALLATION MANUAL
1st Edition

SRX-R515P
!警告
このマニュアルは，サービス専用です。
お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
安全のために，周辺機器を接続する際は，過大電圧を持
つ可能性があるコネクターを以下のポートに接続しない
でください。
: NETWORK コネクター
上記のポートについては本書の指示に従ってください。
For safety, do not connect the connector for periph-
eral device wiring that might have excessive volt-
age to the following port.
: NETWORK connector
Follow the instructions for the above port.
For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
For SRX-R515/XCT-S10

SRX-R515P
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please
make sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
1 (P)
警告
万一，異常が起きた際に，お客様が電源を切ることが
できるように，設置の際には，機器近くの固定配線内
に専用遮断装置を設けるか，機器使用中に，容易に抜
き差しできるコンセントに電源プラグを接続してくだ
さい。
WARNING
When installing the unit, incorporate a readily accessible
disconnect device in the fixed wiring, or connect the
power cord to a socket-outlet which must be provided
near the unit and easily accessible, so that the user can
turn off the power in case a fault should occur.
WARNUNG
Beim Einbau des Geräts ist daher im Festkabel
ein leicht zugänglicher Unterbrecher einzufügen,
oder das Netzkabel mußmit einer in der Nähe
des Geräts befindlichen, leicht zugänglichen
Wandsteckdose verbunden werden, damit sich bei
einer Funktionsstörung die Stromversorgung zum Gerät
jederzeit unterbrechen läßt.
For XCT-S10
本機をラックに設置するとき
熱の適切な排気・発散を得るために，ラックと本機の
間には，以下の空間を確保してください。
.前面 4cm 以上
.後面 10cm 以上
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operating Instructions.
6. When performing the installation, keep the fol-
lowing space away from walls in order to obtain
proper exhaust and radiation of heat.
Front: 4 cm (1.6 inches) or more
Rear: 10 cm (4 inches) or more

1 (E)
SRX-R515P
Table of Contents
4. Connection with External Equipment
4-1. Projector ....................................................................4-1 (E)
4-1-1. Connection Diagram........................................4-1 (E)
4-1-2. Connector Input/Output Signal........................4-2 (E)
4-2. Server ........................................................................4-3 (E)
4-2-1. Connection Diagram........................................4-3 (E)
4-2-2. Connector Input/Output Signal........................4-4 (E)
5. Setting and Adjustment after Connection
5-1. System Startup and Login .........................................5-1 (E)
5-1-1. Startup..............................................................5-1 (E)
5-1-2. Login................................................................5-2 (E)
5-2. About the GUI Screen...............................................5-4 (E)
5-3. Initial Setting.............................................................5-6 (E)
5-3-1. TPC Calibration Setting...................................5-6 (E)
5-3-2. Language Setting .............................................5-8 (E)
5-3-3. Owner Information Setting ..............................5-9 (E)
5-3-4. Date/Time Setting ..........................................5-10 (E)
5-4. Performing the Marriage .........................................5-12 (E)
5-5. Projector Startup...................................................... 5-13 (E)
5-6. Screen Adjustment Flow .........................................5-13 (E)
5-6-1. In the Case of Using Only 2D Lens...............5-14 (E)
5-6-2. In the Case of Using Only 3D Lens...............5-15 (E)
5-6-3. In the Case of Using Both 2D Lens and
3D Lens..........................................................5-15 (E)
5-7. Image Adjustment (2D Lens) ..................................5-16 (E)
5-7-1. Zoom/Focus Adjustment................................5-16 (E)
5-7-2. Position Adjustment....................................... 5-17 (E)
5-7-3. Position Adjustment
(Electric Shift by Touch Panel)......................5-20 (E)
5-7-4. Position Adjustment
(Adjusting the Projector Tilt and Direction)...5-21 (E)
5-7-5. Brightness Adjustment................................... 5-22 (E)
5-7-6. Registration of Adjustment Result
(FUNCTION MEMORY Function)...............5-23 (E)
5-7-7. Calling the Registered Image Information
(FUNCTION MEMORY Function)...............5-24 (E)
Manual Structure
Purpose of this manual............................................................ 3 (E)
Related manuals...................................................................... 3 (E)
Trademarks.............................................................................. 3 (E)
1. Installation Outline
1-1. System Configuration Example................................. 1-1 (E)
1-2. Accessories................................................................1-2 (E)
1-3. Required Equipment/Tools........................................1-3 (E)
1-4. External Dimensions .................................................1-4 (E)
1-4-1. Projector...........................................................1-4 (E)
1-4-2. Server...............................................................1-6 (E)
1-5. Installation Flow........................................................ 1-7 (E)
1-6. Installation of Carrying Handle.................................1-8 (E)
2. Installation of Projector
2-1. Installation of Duct....................................................2-1 (E)
2-2. Installation of Lens....................................................2-2 (E)
2-3. Installation of 3D Lens Filter
(In the Case of LKRA-005)....................................... 2-4 (E)
2-4. Installation of Lamp ..................................................2-7 (E)
2-5. Installation of Touch Panel Monitor..........................2-8 (E)
2-6. Connection of Power Cord......................................2-12 (E)
2-7. Adjustment of Projector Tilt....................................2-14 (E)
3. Installation of Server
3-1. Installation of Server .................................................3-1 (E)
3-1-1. Rack Mounting ................................................ 3-1 (E)
3-1-2. Placing the Server on the Pedestal...................3-3 (E)
3-2. Connection with Projector......................................... 3-4 (E)
3-3. Power Connection .....................................................3-5 (E)
3-4. Power Cord................................................................ 3-6 (E)
3-5. Installation of CRU DATAPORT Carrier..................3-6 (E)

2 (E) SRX-R515P
5-15. Operating This System Using a Personal
Computer (PC) ........................................................ 5-64 (E)
5-15-1. Connection and Startup of PC ....................... 5-64 (E)
5-15-2. Changing the Setting of Firefox.....................5-66 (E)
5-16. Shutdown.................................................................5-70 (E)
6. Installation of Lens Change Table
6-1. Component ................................................................6-1 (E)
6-2. Installation of Foot Assembly ...................................6-1 (E)
6-3. Installation/Adjustment of 2D Unit Assembly..........6-9 (E)
6-3-1. Installation of 2D Unit Assembly ....................6-9 (E)
6-3-2. Height Adjustment of 2D Unit Assembly ...... 6-12 (E)
6-3-3. Check after Adjustment .................................6-14 (E)
6-4. Installation/Adjustment of 3D Unit Assembly........6-18 (E)
6-4-1. Installation of 3D Unit Assembly ..................6-18 (E)
6-4-2. Height Adjustment of 3D Unit Assembly ...... 6-19 (E)
6-4-3. Check after Adjustment .................................6-21 (E)
5-8. Image Adjustment (3D Lens) ..................................5-25 (E)
5-8-1. Optical Axis Adjustment................................5-25 (E)
5-8-2. 3D Lens Filter Adjustment
(In the Case of LKRA-005) ...........................5-27 (E)
5-8-3. Zoom/Focus Adjustment................................5-29 (E)
5-8-4. Position Adjustment
(Using the Lens Shift Mechanism,
Only in the Vertical Direction).......................5-30 (E)
5-8-5. Position Adjustment
(Adjust Image by Touch Panel) ..................... 5-31 (E)
5-8-6. Position Adjustment
(Adjusting the Projector Tilt and Direction)...5-32 (E)
5-8-7. Alignment of the Horizontal Position of Image
for Right Eye and Image for Left Eye ...........5-33 (E)
5-8-8. Image Mapping..............................................5-35 (E)
5-8-9. Brightness Adjustment................................... 5-36 (E)
5-8-10. Registration of Adjustment Result
(FUNCTION MEMORY Function)...............5-37 (E)
5-8-11. Calling the Registered Image Information
(FUNCTION MEMORY Function)...............5-38 (E)
5-9. Color Space Conversion (CSC) Adjustment ...........5-38 (E)
5-10. Check of Video Signal and Audio Output...............5-40 (E)
5-11. Network Setting.......................................................5-41 (E)
5-12. Folder Setting..........................................................5-43 (E)
5-13. Setting of External Equipment................................5-45 (E)
5-13-1. Change in ini File...........................................5-45 (E)
5-13-2. Registration of UPS .......................................5-47 (E)
5-13-3. Registration of Audio Processor ....................5-47 (E)
5-13-4. Setting of GPIO ............................................. 5-48 (E)
5-14. Other Settings..........................................................5-52 (E)
5-14-1. Termination Processing During Generation of a
Fire Alarm or During Occurrence of a Serious
Error in a Projector ........................................5-52 (E)
5-14-2. Periodic Automatic Deletion of File in External
Folder.............................................................5-54 (E)
5-14-3. Setting of Shortcut .........................................5-55 (E)
5-14-4. Log Output Setting ........................................5-56 (E)
5-14-5. Import and Export of Setting Data................. 5-58 (E)
5-14-6. Audio Output Setting.....................................5-59 (E)
5-14-7. Creation of KDM Hot Folder.........................5-60 (E)
5-14-8. Retrieving the Certificate...............................5-61 (E)
5-14-9. Alignment of the Screen Position of
Each Image (R, G and B)...............................5-62 (E)
5-14-10. Turning Off the Lamps Individually..............5-63 (E)

3 (E)
SRX-R515P
Manual Structure
Purpose of this manual
This manual is the installation manual of Digital Cinema Projector Package SRX-
R515P.
This manual is intended for use by trained system and service engineers, and de-
scribes the information for installation of the system.
Related manuals
The following manuals are prepared for this unit.
.Safety Regulations (supplied with this system)
This manual describes the information required to safely use this system.
.Operating Instructions (available on request)
This manual is necessary for application and operation of this system.
.Maintenance Manual (available on request)
This manual describes the information about the system maintenance (periodic
check, cleaning, etc.)
.Service Manual (available on request)
This manual describes the information that premise the service based on part re-
placement of this system.
Trademarks
Trademarks and registered trademarks used in this manual are follows.
.The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
.Windows and Windows 7 are the registered trademarks of Microsoft Corporation
in the United States and Other countries.
Other system names, product names, and company names appearing in this manual
are trademarks or registered trademarks of their respective holders.

1-1 (E)
SRX-R515P
Section 1
Installation Outline
HDMI
UPS
Digital cinema projector
(hereafter referred to as “Projector”)
Digital cinema server
(hereafter referred to as “Server”)
Theater network (LAN)
Device with external video
(HDMI)
Video signal, audio data
USB HDD
Touch panel monitor
PCI-EX, LAN
Audio processor
USB 2.0
VGA, USB 2.0
GPIO
USB 2.0/3.0
RS-232C
D-sub 9 pin
LAN
Automation system
Lighting controller
Curtain controller
1-1. System Configuration Example

1-2 (E) SRX-R515P
1-2. Accessories
The following accessories are supplied with this system.
[Digital Cinema Projector SRX-R515]
.Keys for removing panels (5)
.Safety regulations (1)
.TPC arm (1 set)
.Cable clamper (2)
[Digital Cinema Server XCT-S10]
.Feet (1 set)
.PCI express cable (2 m) (1)
.Ethernet cable (2 m) (1)
[Touch Panel Monitor LKRA-007]
.AC adaptor (1)
.VGA cable (1)
.USB cable (1)

1-3 (E)
SRX-R515P
1-3. Required Equipment/Tools
The equipment and tools required for this system are as follows.
Equipment/tools Description
Projection lens Prepare the necessary lens(es) in accordance with the installation
environment.
.LKRL-Z511
.LKRL-Z514
.LKRL-Z519
.LKRL-A502
.LKRL-A503
n
Regarding the selection of lens, contact your local Sony Sales Office/Service Center.
3D lens filter LKRA-005 etc.
Lens change table LKRA-008
For enabling easy replacement of the 2D lens and 3D lens.
n
When installing the lens change table LKRA-008, refer to Section 6.
Lamp Prepare one of the following lamps in accordance with the installation environment.
.LKRM-U450 (6 pcs, 450 W)
.LKRM-U330 (6 pcs, 330 W)
m
.If all 6 pcs are not inserted, the projector does not operate.
.Regarding the selection of lamp, contact your local Sony Sales Office/Service
Center.
Pedestal _
UPS For the server
Power cable Need to obtain the cable that matches the plug on the installation site.
Exhaust system Connect the duct to the duct connecting portion on the rear top panel for exhausting
the heat inside the projector. In the case of using the 8-inch duct, the following exhaust
air volume is required.
The exhaust air volume of 450-550 ft3/min (12.7 to 15.6 m3/min) should be secured.
External connection cable Refer to Section 4.
Tool Screwdriver (for installing the lamp and server)
Carrying handle Handle arm (part number: 4-164-849-02)
Pipe (short) (part number: 4-164-850-02)
Pipe (long) (part number: 4-164-851-02)
Luminance meter CL-200 or the equivalent
Colorimeter PR-650 or the equivalent
Tripod For the colorimeter and illuminometer
Hexagonal wrench For the 3D lens adjustment: subtense: 2.5, 3.0, 5.0 mm
For the lens shift adjustment: subtense: 5.0 mm
Spanner Subtense: 8 mm (supplied with the lens)
Subtense: 24 mm (for flexible leveler)
Subtense: 30 mm (for nut (M20))
USB mouse, USB keyboard For the connection setting with the external equipment such as audio processor and
UPS

1-4 (E) SRX-R515P
Front view
Left side view
*
(Refer to the optional
lens list.)
Air Intake
Air
Intake
Air
Intake
Heat
exhaust
Input/output
terminal
*
LKRL LIST
No. LKRL L REMARKS
1 Z511 258-297
2 Z514 230-283
3 Z519 244
4 A502 462 Including in 3D lens filter
5 A503 462 Including in 3D lens filter
1-4. External Dimensions
1-4-1. Projector

1-5 (E)
SRX-R515P
Top view
Right side view Rear view
Bottom view
Unit: mm
Heat exhaust
Heat exhaust
Air Intake
Air Intake
Air Intake
Air Intake
Air Intake
Air Intake
Air
Intake
AC power cable
10-M8 (for fixing the projector)

1-6 (E) SRX-R515P
1-4-2. Server
Front view
Top view
Right side view
Rear view
Unit: mm
Input/output
terminal
AC power
cable Heat exhaust
Heat exhaust
Air Intake

1-7 (E)
SRX-R515P
1-5. Installation Flow
The installation procedure for this system is shown in the flow chart.
For the details of each flow, refer to the corresponding item.
n
Basically there is no problem even if Sections 2-1 to 2-5 are not performed in sequential order. However,
do not connect the power cord in Section 2-6 before Sections 2-1 to 2-5 are completed.
Start the installation.
Install the projector.
(Refer to Section 2.)
2-1. Installation of Duct
2-2. Installation of Lens
2-3. Installation of 3D Lens Filter (In the Case of LKRA-005)
2-4. Installation of Lamp
2-5. Installation of Touch Panel Monitor
2-6. Connection of Power Cord
2-7. Adjustment of Projector Tilt
3-1. Installation of Server
3-2. Connection with Projector
3-3. Power Connection
3-5. Installation of CRU DATAPORT Carrier
5-1. System Startup and Login
5-3. Initial Setting
5-4. Performing the Marriage
5-5. Projector Startup
5-7. Image Adjustment (2D Lens)
5-8. Image Adjustment (3D Lens)
5-9. Color Space Conversion (CSC) Adjustment
5-10. Check of Video Signal and Audio Output
5-11. Network Setting
5-12. Folder Setting
5-13. Setting of External Equipment
5-14. Other Settings
5-15. Operating This System Using a Personal Computer (PC)
5-16. Shutdown
6-1. Component
6-2. Installation of Foot Assembly
6-3. Installation/Adjustment of 2D Unit Assembly
6-4. Installation/Adjustment of 3D Unit Assembly
Install the lens change table as required.
Install the server.
(Refer to Section 3.)
Connect the external equipment.
(Refer to Section 4.)
Setting and adjustment
after the connection.
(Refer to Section 5.)
The installation is completed.
Install the lens change table.
(Refer to Section 6.)

1-8 (E) SRX-R515P
Adjuster
Nut B
A
Handle arm
1-6. Installation of Carrying Handle
When moving the projector to the pedestal after unpacking, attach the carrying handles as required for
transporting it.
n
The carrying handles cannot be attached to both back/forth and right/left at the same time.
Parts information
.Handle arm: 4-164-849-02: 4 pcs
.Pipe (short): 4-164-850-02: 2 pcs
.Pipe (long): 4-164-851-02: 2 pcs
.M8 bolt: 2-590-262-02 or -11: 4 pcs
In the case of attaching the pipe (long) to the right and left side of projector
1. Loosen the nut in the direction of the arrow A, then insert the handle arm in the direction of the
arrow B.
2. Tighten the nut to fix the handle arm.
3. Attach the handle arm to the adjuster of other three portions by repeating steps 1 and 2.

1-9 (E)
SRX-R515P
4. Insert the pipe (long) into the handle arms, then fix the pipe with the two M8 bolts.
5. Attach the pipe (long) on the other side in the same way.
Pipe (long)
Pipe (long)
Handle arm
Handle arm
Handle arm
M8 bolts

1-10 (E) SRX-R515P
Adjuster
Nut
Handle arm
B
A
In the case of attaching the pipe (short) to the back and forth of projector
n
The procedure is the same as the pipe (long).
1. Loosen the nut in the direction of the arrow A, then insert the handle arm in the direction of the
arrow B.
2. Tighten the nut to fix the handle arm.
3. Attach the handle arm to the adjuster of other three portions by repeating steps 1 and 2.

1-11 (E)
SRX-R515P
4. Insert the pipe (short) into the handle arms, then fix the pipe with the two M8 bolts.
5. Attach the pipe (short) on the other side in the same way.
Pipe (short)
Pipe (short)
Pipe (short)
M8 bolts