Sony SRXT615 User manual

4K Digital Projector
Operating Instructions
Before operating the unit, please read this manual and supplied Safety Regulations
thoroughly and retain it for future reference.
SRX-T615
4-488-198-11 (1)
© 2013 Sony Corporation

2Table of Contents
Table of Contents
Important Notes ........................................................ 3
Related Manuals .................................................... 3
Overview
Parts Identification ................................................... 4
Projector ................................................................. 4
SRX Controller Program Launcher Screen ........... 5
Main Screen of SRX Controller ............................ 6
Preparation
Precautions for Installation and Use ....................... 9
Unsuitable Environments ....................................... 9
Unsuitable Operating Conditions ........................ 10
Installing SRX Controller on the Controller
PC ............................................................................. 10
Operating Environment ........................................ 10
Installing SRX Controller .................................... 11
Connecting the Controller PC ............................... 12
Connecting to the NETWORK Connector .......... 12
Connecting to the RS-232C Connector ............... 13
Connecting the Projection Source Device ............. 13
Verification
Startup ..................................................................... 14
Turning On the Main Power of the Projector ...... 14
Starting SRX Controller ...................................... 14
Starting the Projector ........................................... 15
Turning Off the Projector ...................................... 16
Projection
Projecting Images onto a Screen ............................ 17
Masking Images ................................................... 17
Adjusting the Edge Blending ............................... 18
Adjustments and Settings
SRX Controller Adjustments and Settings ........... 19
Storing Setting Values .......................................... 19
[PICTURE CONTROL] Tab ................................. 20
[COLOR CONFIG.] Tab ........................................ 21
[INSTALLATION] Tab .......................................... 22
[LENS CONTROL] ............................................. 22
[ELECTRIC SHIFT FUNCTION] ...................... 22
[LAMP POWER] ................................................. 22
[IMAGE FLIP] ..................................................... 22
[3D GAMMA SELECT] ..................................... 22
[SINGLE 3D ADJUST] ....................................... 22
[TEST PATTERN] ............................................... 23
Miscellaneous
Lamp Replacement Cycles ..................................... 24
Troubleshooting ....................................................... 24
Messages ................................................................... 25
Specifications ........................................................... 28
Trademarks
• Microsoft, Windows, and Windows Vista are
trademarks or registered trademarks of Microsoft
Corporation in the United States and other countries.
• Intel and Pentium are registered trademarks of Intel
Corporation in the United States and other countries.
• The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
• Other products or system names appearing in this
document are trademarks or registered trademarks of
their respective owners.
Further, the ® or ™ symbols are not used in the text.
• Reproduction or duplication, in whole or part, of the
operation manual supplied with the system without
the authorization of the right holder is prohibited
under copyright law.
• Sony assumes no responsibility for damages, loss of
income, or any claims from a third party arising out
of use of the system.
• Note that the specifications of the system are subject
to change for improvement without prior notice.

3
Important Notes
Important Notes
Related Manuals
The following manuals are provided for the SRX-T615.
Safety Regulations
This includes instructions and precautions for safe
operation of the SRX-T615.
Installation Manual
This includes instructions on how to install and configure
initial settings for the SRX-T615, and how to perform
adjustments for devices. Refer to this manual whenever
you want to change settings or readjust the devices after
installation.
Operating Instructions (this manual)
This includes information on projection operations,
procedures for adjustment and configuration via SRX
Controller, names and functions of parts, and
specifications.
Refer to this manual for information on general day-to-day
operations.
Maintenance Manual
This includes information such as instructions on periodic
inspection, maintenance, and cleaning.
Service Manual
This is intended for use by service personnel and includes
information on diagnosing malfunctions and instructions
on repair.

4Parts Identification
Overview
Overview
Parts Identification
Projector
Front
a8-inch duct attachment point
Attach an exhaust duct here.
bLens lock lever
Locks or releases a lens.
cLens attachment point
Attach a lens (not supplied) here.
For details on lens attachment or replacement, contact
your dealer or your local Sony representative.
Rear
aEMERGENCY switch
Forces the lamp to turn off (enters standby after
cooling).
bMessage display window
Displays various messages (page 25).
cStatus indicators
Indicate the projector’s status.
Tips
The IMB indicator lights red under normal
circumstances. However, this may change depending
on the options you install.
dStatus lights
These operate when the server is connected.
ePower switch
Turns the projector’s main power on (|) or off (a).
To turn the projector off
Wait for the lamp’s cooling process to complete
before turning the power switch off.
For details, see “Turning Off the Projector”
(page 16).
Left side
aLamp access panel (lamp grill) / intake vent / air
filter
A lamp access panel (lamp grill) / intake vent / air
filter is also located on the right side of the projector.
MAIN LAMP Projector status
Lit red Lit red Standby mode
Lit green Blinking green
(rapid)
Starting up
Lit green Lit green Power on (lamp lit)
Lit green Blinking green
(slow)
Power on (lamp off)
Blinking green
(rapid)
Blinking green
(rapid)
Cooling
Connectors

5
Parts Identification
Overview
bIntake vent / air filter
For details on lamp replacement or filter cleaning, contact
your dealer or your local Sony representative.
AConnectors
aNETWORK connector (RJ-45 modular jack)
Connect a LAN cable (not supplied) here and use it to
connect to the computer on which the SRX Controller
software is installed (controller PC). The controller
PC is used to operate the projector.
bINTER LOCK connector (D-sub 15-pin, female)
Used for maintenance.
cRS-232C connector (D-sub 9-pin, female)
Connect a connection cable (not supplied) here and
use it to connect to the computer on which the SRX
Controller software is installed (controller PC). The
controller PC is used to operate the projector.
dHDMI IN 1/2 connectors
Input HDMI signals here.
For details on signal formats, see “HDMI signals”
(page 29).
SRX Controller Program Launcher Screen
a[File] menu
Includes the following commands.
[Quit]: Quits SRX Controller.
b[Connect] menu
Allows you to select the connection mode used to
connect the projector and the controller PC.
Includes the following commands.
[Network]: Select this when the projector is
connected to the controller PC via LAN
(page 12).
[COM]: Select this when the projector is connected to
the controller PC via RS-232C (page 13).

6Parts Identification
Overview
[PC Port Setting]: Allows you to change the port
number.
c[Help] menu
Includes the following commands.
[Version]: Displays version information for SRX
Controller.
dProjector list
Displays a list of information on projectors that are
connected to the same network (subnet). A projector
that can be connected via either IPv4 or IPv6 will be
listed twice as separate projectors.
When you double-click a projector in the list,
connection to the projector is established and the main
screen of SRX Controller appears.
[Alert]: Not supported.
[Model Name]: Displays the projector’s model name.
[Serial No.]: Displays the projector’s serial number.
[Type]: Displays the protocol type (IPv6/IPv4) that
can be used for connection.
[IP Adress]: Displays the projector’s IP address.
[Connection]: Indicates the network connection
status.
“Connectable” will appear for projectors that can
be selected from SRX Controller.
[Power]: Indicates the power status of the projector.
[Region]: Displays the region in which the projector
is installed (only if this information is registered).
[Location]: Displays the location in which the
projector is installed (only if this information is
registered).
[Name]: Displays the projector’s name (only if this
information is registered).
Main Screen of SRX Controller
a[File] menu
Includes the following commands.
[Save Log]: Used for maintenance.
For details, contact your dealer or your local
Sony representative.
[Quit]: Quits SRX Controller.
b[Password] menu
Includes the following commands.
[Reset]: Allows you to reset the password required
for authentication when displaying the
[SERVICE] and [SETTING] tabs.
This menu only appears when a user with
administrator privileges has started SRX
Controller.
[SCREEN CONTROL] block

7
Parts Identification
Overview
For details on the [SERVICE] and [SETTING]
tabs, contact your dealer or your local Sony
representative.
c[Help] menu
Includes the following commands.
[Version]: Displays version information for SRX
Controller.
[Serial]: Displays the projector’s serial number.
dPOWER indicator
Displays the projector’s status.
e(STANDBY) button
Turns the projector off (page 16).
f(ON) button
When the MAIN and LAMP indicators on the rear of
the projector are lit, pressing this button turns the
projector on.
When the MAIN and LAMP indicators on the rear of
the projector and the POWER indicator on the SRX
Controller screen light green, you can control the
projector via the SRX Controller screen.
For details, see “Startup” (page 14).
gInformation display area
[Location]: Displays the projector’s installation
location configured in the [SETTING] tab.
[Name]: Displays the projector’s name configured in
the [SETTING] tab.
Lamp indicators: Displays lamp status.
[Warning Info]: Displays an error message if a
malfunction occurs on the projector (page 25).
h[FUNCTION]
Select the FUNTION you want to use.
You can register adjustments and settings configured
for the projector in the SRX Controller screen to
FUNCTION 1 to FUNCTION 8, and recall them
whenever necessary.
For details, see “Storing Setting Values” (page 19).
iTabs
Allow you to perform various adjustments and
settings.
[PICTURE CONTROL] tab: Allows you to select
the input signal and adjust the picture quality
(page 20).
[COLOR CONFIG.] tab: Allows you to configure
settings for proper color reproduction (page 21).
[INSTALLATION] tab: Allows you to adjust and
configure settings related to projector installation
(page 22).
[SERVICE] tab: Allows you to adjust the projector.
A password is required to open this tab. For
details, contact your dealer or your local Sony
representative.
[SETTING] tab: Allows you to configure projector
settings.
A password is required to open this tab. For
details, contact your dealer or your local Sony
representative.
Color and
light status
Status
Lit green The projector is ready to be operated via
the SRX Controller screen.
Blinking green Standby mode (cooling)
Lit red Standby mode
Color Status
White Functioning normally
Yellow 80% of the recommended replacement cycle’s
duration has passed.
Red The recommended replacement cycle’s
duration has passed.
Gray The lamp is not lit.
× mark A lamp error has occurred.

8Parts Identification
Overview
A[SCREEN CONTROL] block
a[INPUT SELECT] area
Allows you to select the input signal to be projected
onto the screen (page 17).
b[MASKING ADJUST/EDGE BLENDING] area
Allows you to apply black masking to undesired areas
of the image according to the screen (page 17).
You can also perform edge blending adjustments here
(page 18).
c[MUTING] area
Allows you to display a black screen by blocking all
light through the use of a shutter.
[ON]: Temporarily blocks the entire image that is
projected onto the screen (i.e., a black screen will
be displayed).
[OFF]: Displays the image.
d[CUT OFF] area
Use this to display 3D images.
For details, contact your dealer or your local Sony
representative.

9
Precautions for Installation and Use
Preparation
Preparation
Precautions for
Installation and Use
Unsuitable Environments
Do not install the projector in the following types of
environments. Doing so may result in malfunctions or
damage to the projector.
Poorly ventilated locations
The intake and exhaust vents prevent the projector’s
interior from overheating. Avoid installation in locations
with poor ventilation, and make sure the intake and exhaust
vents are free from obstructions.
Locations that obstruct the intake and
exhaust vents
If objects are placed near the exhaust vents located on the
top of the projector and on its sides, exhaust will flow into
the intake vents. This may cause the projector’s interior to
overheat and the protection circuit to activate. Be sure to
leave sufficient space for the exhaust to escape when
installing the projector. Maintain a clearance of about 1 m
(39 3/8in.) between the projector and objects.
Locations subject to high temperature and
humidity
Locations subject to sudden temperature
changes
Sudden temperature changes in an enclosed space where
the projector is installed will result in condensation, which
may in turn result in malfunctions. Be careful when using
air conditioners.
Dusty locations

10 Installing SRX Controller on the Controller PC
Preparation
Unsuitable Operating Conditions
Do not operate the projector under the following
conditions.
Projector tilted to the left or right
Avoid operating the projector if it is tilted ±10 degrees or
more. Doing so may result in color distortion and
significant shortening of the lamp life.
Intake and exhaust vents covered
Do not use covers that may obstruct the intake or exhaust
vents, and do not operate the projector on thick-piled
carpets, for example. Obstructing the intake and exhaust
vents will result in overheating of the projector’s interior.
For details on the locations of the intake and exhaust
vents, see “Parts Identification” (page 4).
Installing SRX Controller
on the Controller PC
Install the SRX Controller software on the computer you
will use to control the projector.
If a previous version of SRX Controller is already installed
on the computer, uninstall the previous version
beforehand.
Operating Environment
A computer that meets the following conditions is required
to operate SRX Controller.
Operating system (OS):
Windows XP Professional SP3 (English or Japanese
edition, excluding x64 edition)
Windows Vista Business SP2 (English or Japanese
edition, excluding x64 edition)
Windows 7 Enterprise SP1 (English or Japanese
edition)
CPU: Intel Pentium M 1.6 GHz or higher,
OS-recommended CPU
Memory: 256 MB or higher (512 MB or higher
recommended), OS-recommended memory
Available HDD space: 15 MB or higher (internal drive)
Monitor: XGA (1024 × 768) or higher
Communication: LAN (10BASE-T/100BASE-TX) or
COM (RS-232C)
Windows Vista/7 User Account Control
Windows Vista/7 includes User Account Control (UAC) to
improve file security.
SRX Controller supports UAC, and UAC warning
messages may appear during installation or operation.
If warning messages appear, perform the following.
If the following screen appears
Select [Allow] to continue with the operation.

11
Installing SRX Controller on the Controller PC
Preparation
Notes
The application will not run if you select [Cancel].
If the administrator password entry screen
appears
Enter the administrator password, and click [OK].
Installing SRX Controller
1 Start the installation wizard that was downloaded via
the installer.
The installation wizard starts.
2 Click [Next].
The software license agreement appears.
3 Read the agreement, select [I accept the terms in the
license agreement], and then click [Next].
If you select [I do not accept the terms in the license
agreement], the software will not be installed and the
wizard will close.
4 Select the destination folder for installation, and click
[Next].
To change the destination for installation, click
[Change] and specify the folder to which you want to
install.
5 Click [Install].
Installation starts.

12 Connecting the Controller PC
Preparation
6 When the following screen appears, click [Finish].
If you selected the [Launch the program] checkbox,
SRX Controller will start immediately.
This completes installation of SRX Controller.
When SRX Controller is installed, the ìStart SRX
Controller for SRX-T seriesî icon is created on your
desktop.
Connecting the Controller
PC
Connect the controller PC to the NETWORK connector or
RS-232C connector on the projector, depending on your
operating environment.
Notes
If both the NETWORK connector (LAN) and the RS-232C
connector (COM) are connected at the same time,
communication errors may occur. Use only one connection
at a time.
Connecting to the NETWORK
Connector
Use a LAN cable (not supplied) to connect the
NETWORK connector on the projector to the LAN
connector on the controller PC.
You can also use a LAN cable (straight) (not supplied) and
connect to a network via a hub.
to NETWORK
connector
LAN cable (crossover cable)
(not supplied)
Controller PC
to LAN connector

13
Connecting the Projection Source Device
Preparation
Connecting to the RS-232C
Connector
Use a connection cable (not supplied) to connect the
RS-232C connector on the projector to the RS-232C
connector on the controller PC.
Connecting the
Projection Source Device
Notes on connection
• Perform connections for devices with their breakers off
or with their power cords disconnected.
• Use appropriate connection cables based on each of the
connectors.
• Fully insert all plugs. Incomplete connections may result
in image distortion. Be sure to grasp the plug portions
when performing disconnections.
• As an additional reference, refer to the operating
instructions of the device you want to connect.
For details on supported signals, “HDMI signals”
(page 29).
Connect the HDMI IN 1/2 connector on the projector to a
device equipped with HDMI output, such as a computer or
Blu-ray Disc player.
to RS-232C
connector
Connection cable (crossover cable)
(not supplied)
to RS-232C
connector
Controller PC
to HDMI IN 1
connector
to HDMI IN
2 connector
HDMI connection
cable (not supplied)
Computer Blu-ray Disc
player, etc.
to HDMI output
connector
to HDMI output
connector

14 Startup
Verification
Verification
Startup
Turn on the projector’s main power, start SRX Controller,
and then start the projector.
Turning On the Main Power of the
Projector
Raise the power switch on the rear of the projector to the
on position (|) to turn on the projector.
The main power of the projector will turn on and enter the
standby mode, the MAIN indicator and LAMP indicator
will light red.
Notes
Connect to SRX Controller after initialization of the
projector is complete and after the message in the message
display window disappears.
Starting SRX Controller
Start SRX Controller, and connect to the projector you
want to operate.
Starting the software
If the controller PC is running Windows XP SP3 or later or
has commercially available firewall software installed, or
the Windows firewall is enabled, the firewall settings must
be disabled.
When running Windows XP SP3 or later
• If the following dialog box appears during SRX
Controller startup, click [Unblock].
• If the dialog box does not appear and connection to the
projector is not possible, open [Windows Firewall] from
the [Control Panel], and add “SRX Controller” to the list
in the [Exceptions] tab.
When running Windows 7
Start [Windows Firewall], click [Allow a program or
feature through Windows Firewall], and select the
checkbox for SRX Controller in the list of allowed
programs and features. If SRX Controller does not appear
in the list, select [Change settings], and then add it by
clicking [Add another program].
When commercially available firewall software is
installed
Refer to the operating instructions of the firewall software,
and add “SRX Controller” to the “authorized” list.
When connected via LAN
1 Click on the desktop.
The program launcher screen appears.
2 Double-click the projector you want to operate in the
projector list.
The main screen of SRX Controller appears when
connection with the projector is established.

15
Startup
Verification
To connect by specifying the projector’s IP
address
Select [Network] in the [Connect] menu, enter the
projector’s IP address for [Projector IP Address] in the
[Network] dialog box that appears, select [SRX-T600
series] for [Select Model] and then click [OK].
Tips
• Direct specification of the IPv6 address is not supported.
When projectors that can be connected via IPv6 exist on
the same subnet, they will appear in the projector list, so
connect to them from there.
• If other items (services) are enabled for the network
connection, projectors may not appear in the projector
list of the program launcher screen. In such cases,
disable that item (service) or connect to projectors by
specifying their IPv4 addresses.
• To change the port number, select [PC Port Setting] in
the [Connect] menu, and enter the port number in the
dialog box that appears.
• The projector’s IPv4 address will appear in the message
display window when the main power is turned on using
the breaker. Match the IPv4 address of the computer you
are using, and perform connection.
When connected via RS-232C
1 Click on the desktop.
The program launcher screen appears.
2 Select [COM] in the [Connect] menu.
The [COM] dialog box appears.
3 Enter the controller PC’s COM port (RS-232C) for
[COM Port], select [SRX-T600 series] for [Select
Model], and then click [OK].
The main screen of SRX Controller appears when
connection with the projector is established.
Quitting SRX Controller
Select [Quit] in the [File] menu.
Starting the Projector
Click at the top right of the main screen of SRX
Controller.
The MAIN and LAMP indicators on the projector and the
POWER indicator on the main screen of SRX Controller
light green.
This completes the preparations and verifications required
to project images onto a screen.

16 Turning Off the Projector
Verification
Turning Off the Projector
1 Click at the top right of the main screen of
SRX Controller.
A confirmation screen appears.
2 Click [OK].
The MAIN and LAMP indicators on the rear of the
projector will begin to blink green to indicate that
cooling is in progress. When cooling is complete, the
LAMP indicator will light red. Wait a moment.
While cooling is in progress, the POWER indicator on
the main screen of SRX Controller will also blink
green.
3 When the MAIN and LAMP indicators light red,
lower the breaker to the off position (a) to turn off the
main power.
Notes
Do not turn off the projector using its power switch.
Forcibly turning off the projector using the power switch
may result in insufficient cooling of the lamp, which may
in turn cause shortening of the lamp life and malfunctions.

17
Projecting Images onto a Screen
Projection
Projection
Projecting Images onto a
Screen
Operations for projection are performed in the SRX
Controller screen.
1 Turn on the main power of the projector (page 14).
2 SRX Controller starts, and connection with the
projector is established (page 14).
3 Start the projector (page 15).
4 Turn on the source device of the images.
5 Select the input signal under [INPUT SELECT] of the
[SCREEN CONTROL] block.
HDMI-1: Project images from the device connected
to the HDMI IN 1 connector.
HDMI-2: Project images from the device connected
to the HDMI IN 2 connector.
AUX × 1: When a 4K option board is installed,
project the 2K input signal.
AUX × 4: When a 4K option board is installed,
project the 4K input signal.
SERVER: Intended for future expansion.
Notes
• If the [Signal Mode] is not configured correctly
under [Input Source] in the [PICTURE CONTROL]
tab, the image may be distorted.
• For details on connector locations for optional
external input boards, refer to the operating
instructions supplied with the external input boards.
For details, see “[PICTURE CONTROL] Tab”
(page 20).
6 Display the [INSTALLATION] tab, and adjust the
focus and viewing angle under [LENS CONTROL].
1Click [–] or [+] for [Focus] to adjust the focus.
2Click [–] or [+] for [Zoom] to adjust the picture
size.
3Adjust the focus again with [Focus].
Blocking the entire image
Click the [ON] button under [MUTING] in the [SCREEN
CONTROL] block to block the image and make the entire
screen go black.
Clicking the [OFF] button restores the image display.
Masking Images
You can apply black masking to undesired areas of the
image according to the screen.
You can adjust any of the eight adjustment points.
1 Double-click one of the adjustment points under
[MASKING ADJSUT/EDGE BLENDING] in the
[SCREEN CONTROL] block.
The adjustment screen appears.
2 While viewing the image projected on the screen,
click the [–] or [+] buttons for [Horizontal] or
[Vertical], or enter values to perform adjustments.
3 Repeat the above for each adjustment point to mask
the image.
13 2
Adjustment point

18 Projecting Images onto a Screen
Projection
Restoring the default adjustment values
Click [RESET] to restore all the adjustment points to their
default values.
Adjusting the Edge Blending
You can adjust the edge blending to smoothen the joints
between multiple images when conjoining images from
multiple projectors.
Configure the areas you want to blend and the widths as
follows.
• To blend the left and right edges: Set [Horizontal] to “the
blending width + 48.”
• To blend the top and bottom edges: Set [Vertical] to “the
blending width + 50.”
This section describes how to blend horizontally using a
right-edge blending width of 512 as an example.
1 Double-click the top right adjustment point under
[MASKING ADJUST/EDGE BLENDING] in the
[SCREEN CONTROL] block, and enter “560” for
[Horizontal] in the adjustment screen that appears.
Setting value: Blending width 512 + 48 = 560
2 Double-click the bottom right adjustment point, and
enter “560” for [Horizontal] in the adjustment screen
that appears.
Setting value: Blending width 512 + 48 = 560
3 Click [BLENDING].
The [EDGE BLENDING] screen appears.
4 Set [Right] to [ON], and select [512] for [Width].
If you set [Marker] to [On], green and red lines will
appear at the start and end positions of blending,
respectively.
Notes
We recommend setting [Upper] and [Lower] to [256]
or [512].
5 When you finish configuration, click [CLOSE].

19
SRX Controller Adjustments and Settings
Adjustments and Settings
Adjustments and Settings
SRX Controller
Adjustments and
Settings
Adjustments and settings are performed in the various tabs
of the SRX Controller screen.
This section describes the setting items in each tab.
Items that cannot be adjusted
Depending on the input signal, some setting items cannot
be configured. Setting items that cannot be configured will
not appear in the SRX Controller screen.
Storing Setting Values
Settings and adjustments configured for the projector can
be registered to a FUNCTION to be recalled whenever
necessary.
You can register up to 8 FUNCTIONs (FUNCTION 1 to
FUNCTION 8).
Registering setting values to FUNCTIONs
Setting values are stored to FUNCTION 1 under factory
default conditions.
To register additional FUNCTIONs, perform the
following.
1 Select the FUNCTION you want to register in the
[FUNCTION] drop-down list.
2 Perform adjustments and settings in each tab.
The current setting values will be stored to the
selected FUNCTION.
Recalling FUNCTIONs
Select the FUNCTION you want to recall in the
[FUNCTION] drop-down list.
Notes
When you switch to a different FUNCTION, the image
will temporarily enter the muting state for up to about
10 seconds. Afterward, the image will appear according to
the selected settings.

20 [PICTURE CONTROL] Tab
Adjustments and Settings
[PICTURE CONTROL] Tab
You can select the input signal and adjust the picture
quality in the [PICTURE CONTROL] tab.
[Input Source]
[Signal Mode]
Select the type of signal that is input from the device
connected to the input board.
[D Range]
Set the dynamic range to [Full Range], [Limited Range], or
[Auto].
[Limited Range] assumes that the signal includes restricted
codes, and performs adjustments so that data values 64 to
960 are at a 0% to 100% image levels in the case of a 10-bit
signal. When the signal includes restricted codes, select
[Limited Range].
[I/P Mode]
Select the I/P conversion mode.
Select [Auto Interlace] or [Auto PsF] depending on the
signal source.
[Signal Info]
Displays the horizontal and vertical frequencies
automatically. The values are rough estimates.
The input signal type is displayed under the frequency
values.
[fH]: Displays the horizontal frequency.
[fV]: Displays the vertical frequency.
Notes
If [Single 3D] is selected for [INPUT SELECT], signal
information will not be displayed in the right eye settings
if it is common to the left eye settings.
[Signal Adjust]
Adjust the picture quality of the input signal.
Click [+] to increase a setting value, and click [–] to
decrease it.
Clicking the [RESET] button restores all the setting values
below it to their default values.
[Contrast]
Adjust the contrast.
Increasing the value increases the contrast.
[Brightness]
Adjust the brightness.
Increasing the value increases the brightness.
[Color]
Adjust the color density.
Increasing the value increases the color density.
Notes
If [Single 3D] is selected for [INPUT SELECT], items will
not be displayed in the right eye settings if they are
common to the left eye settings.