Sony VPL-EX100 User manual

DATA PROJECTOR
VPL-EX100
VPL-EX120
VPL-EX145
VPL-EX175
VPL-F400H
VPL-F400X
VPL-F500X
VPL-F700HL
VPL-F700XL
VPL-FH30
VPL-FH500L
VPL-FX30
VPL-FX35
VPL-FX500L
PROTOCOL MANUAL
1st Edition (Revised 3)

VPL Series PROTOCOL MANUAL
!警告
このマニュアルは，サービス専用です。
お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

1 (T)
VPL Series PROTOCOL MANUAL
Table of Contents
1. Overview
1-1. Introduction ........................................................................ 1
1-2. Glossary of Terms .............................................................. 1
1-3. Protocol Stack Structure..................................................... 1
2. Common Commands
2-1. Sub Commands .................................................................. 3
2-1-1. ITEM List ................................................................. 3
2-1-2. Infrared Remote Command Code........................... 13
2-2. Reply ................................................................................ 16
3. RS-232C
3-1. Connection ....................................................................... 17
3-2. Communication Specifications......................................... 17
3-3. Communication Procedure............................................... 18
3-3-1. Outline of Communication ..................................... 18
3-4. Communication Rules...................................................... 18
3-5. Approximate Return Waiting Times................................. 18
3-6. Command Block Format .................................................. 19
3-6-1. Simplified Command .............................................. 19
3-7. Packet Examples .............................................................. 20
3-7-1. Change “ASPECT” to “ZOOM” ............................ 20
3-8. AMX Device Discovery................................................... 20
4. Ethernet
4-1. Service.............................................................................. 21
4-1-1. Advertisement......................................................... 21
4-1-2. PJ Talk..................................................................... 22
4-2. Communication Procedure............................................... 23
4-3. Protocols........................................................................... 24
4-3-1. SDAP ...................................................................... 24
4-3-2. SDCP....................................................................... 25
4-3-3. SNMP...................................................................... 33
4-3-4. PJLink ..................................................................... 34
4-3-5. DDDP...................................................................... 41

1
VPL Series PROTOCOL MANUAL
1. Overview
1-1. Introduction
The projector is remotely controllable over RS-232C as well as Ethernet. It is useful for setting up the
projector away from the operator.
This protocol manual describes the specifications such as packet format and procedures for controlling the
projector.
In the following sections below, the term “CONTROLLER” is used as a device which controls the projec-
tor. CONTROLLER can be a PC or other specific device that is able to handle RS-232C or Ethernet.
Although most of commands are available for both RS-232C and Ethernet, some commands are dedicated
to Ethernet.
*Ethernet is a registered trademark of Xerox Corporation.
1-2. Glossary of Terms
Table 1-1 Glossary of Terms
Terms Abbreviated Description
CONTROLLER _Command initiator such as PCs.
PROJECTOR _Front projector.
SDAP Simple Display Advertisement Protocol Protocol name for advertising the projector status over
Ethernet.
SDCP Simple Display Control Protocol Protocol name for controlling projector over Ethernet.
PJLink _Protocol name for controlling projector over Ethernet.
DDDP Dynamic Device Discovery Protocol AMX Device Discovery is the protocol name by AMX
to enable to configure the AMX control system and
other intended devices.
1-3. Protocol Stack Structure
The protocol stack structure diagram is shown below. Though the stack is drawn for RS-232C and Ether-
net separately, the following portions are common.
Table 1-2 Common Portions in Protocol Stack
Layer Name Description
Sub Command Value is assigned for projector’s functions. Refer to the section 2-1 for detail description.
Simplified Command Packet format for sending/receiving “Sub Command”. Refer to the section 3-6-1 for detail
description.

2VPL Series PROTOCOL MANUAL
(1) RS-232C
Fig. 1-1 RS-232C Protocol Stack
“RS-232C” layer is physical portion and “Asynchronous” is the traditional protocol layer as shown in the
section 3-2.
(2) Ethernet
Fig. 1-2 Ethernet Protocol Stack
Ethernet corresponding model
VPL-FH30, VPL-FH500L, VPL-FX30, VPL-FX35, VPL-FX500L, VPL-F400H, VPL-F400X, VPL-
F500X, VPL-F700HL, VPL-F700XL, VPL-EX145, VPL-EX175
Because of traditional portions for Ethernet general layer, “TCP/IP”, “UDP/IP”, “HTTP” and “SNMP”
are out of scope in this document.
SDCP specific command is described in the section 4-3-2.
SDAP and SDCP (PJ Talk) are SONY original protocol stack, which are described in the sections 4-3-1
and 4-3-4 respectively.
RS-232C
Simplified Command
Asynchronous
Sub Command
AMX Device
Discovery
SDAP
SDCP Specific Command
SNMP DDDPPJLinkHTTP
UDP/IP
Ethernet
TCP/IP
SDCP (PJ Talk)
Sub
Command
Simplified
Command

3
VPL Series PROTOCOL MANUAL
2. Common Commands
2-1. Sub Commands
Sub Command is the value which is used by Simplified Command. Value is assigned for executing func-
tion. For example, if you want to change the picture mode, the appropriate value assigned for the desired
picture mode should be chosen.
2-1-1. ITEM List
Item lists are described below. Tables are shown per function category.
VPL-FH30/FX30/FX35/F400H/F400X/F500X
ITEM List For Picture
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
PICTURE MODE 00h 02h DYNAMIC 0000h Set/Get
STANDARD 0001h
PRESENTATION 0002h
CONTRAST 00h 10h VALUE 0000h-0064h(0-100)
BRIGHTNESS 00h 11h VALUE 0000h-0064h(0-100)
COLOR 00h 12h VALUE 0000h-0064h(0-100)
HUE 00h 13h VALUE 0000h-0064h(0-100)
SHARPNESS 00h 14h VALUE 0000h-0064h(0-100)
EXT. OUTPUT VOLUME 00h 16h VALUE 0000h-0064h(0-100)
COLOR TEMP 00h 17h HIGH 0000h
MID 0001h
LOW 0002h
CUSTOM1 0005h
CUSTOM2 0006h
CUSTOM3 0007h
BLACK LEVEL ADJ 00h 1Ch OFF 0000h
LOW 0001h
HIGH 0002h
FILM MODE 00h 1Fh OFF 0000h
AUTO 0001h

4VPL Series PROTOCOL MANUAL
ITEM List For Screen
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
ASPECT 00h 20h FULL 0000h Set/Get
NORMAL 0001h
ZOOM 0003h
FULL1 0007h
FULL2 0008h
4:3 0009h
16:9 000Ah
OVER SCAN 00h 23h OFF 0000h
ON 0001h
ITEM List For Setup
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
INPUT TERMINAL 1 00h 01h VIDEO 0000h Set/Get
SVIDEO 0001h
INPUTA 0002h
INPUTB 0003h
INPUTC 0004h
INPUTD*0005h
MULTI SCREEN MODE*00h 03h OFF 0000h
TWIN 0001h
INPUT TERMINAL 2*00h 04h VIDEO 0000h Get
SVIDEO 0001h
INPUTA 0002h
INPUTB 0003h
INPUTC 0004h
INPUTD 0005h
PICTURE MUTING 00h 30h OFF 0000h Set/Get
ON 0001h
AUDIO MUTING 00h 31h OFF 0000h
ON 0001h
INPUT A SIGNAL-SEL 00h 32h AUTO 0000h
COMPUTER 0001h
COMPONENT 0002h
VIDEO GBR 0003h
LAMP MODE 00h 40h HIGH 0000h
STANDARD 0001h
*: VPL-FH30/F400H only

5
VPL Series PROTOCOL MANUAL
ITEM List For Infrared Remote Command
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Infrared Remote Command
(15 bit category)
17h Refer to Section
2-1-2.*1
_00h 00h Set only
Infrared Remote Command
(20 bit E category)
19h _00h 00h
Infrared Remote Command
(20 bit EE category)
1Bh _00h 00h
*1: For using this item number, the simulation of the infrared remote controller is enable. Select the corresponding code in the table of
Section 2-1-2 and use it as the lower byte of the item number.
n
Other value is assigned depending for category.

6VPL Series PROTOCOL MANUAL
ITEM List For Status
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
STATUS ERROR1 01h 01h NO ERROR 00h Get only
LAMP ERROR 01h
FAN ERROR 02h
COVER ERROR 04h
TEMP ERROR 08h
D5V ERROR 10h
POWER ERROR 20h
WARNING TEMP 40h
NVM DATA ERROR 80h
STATUS POWER 01h 02h STANDBY 00h
START UP 01h
STARTUP LAMP 02h
POWER ON 03h
COOLING1 04h
COOLING2 05h
SAVING COOLING1 06h
SAVING COOLING2 07h
SAVING STANDBY 08h
LAMP TIMER 01h 13h VALUE xxh
SUB ROM VERSION 01h 1Dh VALUE xxh
MAIN ROM VERSION 01h 1Eh VALUE xxh
STATUS SECURITY 01h 1Fh DISABLE 00h
ENABLE 01h
STATUS ERROR2 01h 25h NO ERROR 00h
Don’t Use 01h
Don’t Use 02h
Don’t Use 04h
Don’t Use 08h
Don’t Use 10h
WARNING HIGHLAND 20h
Don’t Use 40h
Don’t Use 80h
NVM DATA VERSION 01h 27h VALUE xxh

7
VPL Series PROTOCOL MANUAL
VPL-FH500L/FX500L/F700HL/F700XL
ITEM List For Picture
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
PICTURE MODE 00h 02h DYNAMIC 0000h Set/Get
STANDARD 0001h
PRESENTATION 0002h
CONTRAST 00h 10h VALUE 0000h-0064h(0-100)
BRIGHTNESS 00h 11h VALUE 0000h-0064h(0-100)
COLOR 00h 12h VALUE 0000h-0064h(0-100)
HUE 00h 13h VALUE 0000h-0064h(0-100)
SHARPNESS 00h 14h VALUE 0000h-0064h(0-100)
COLOR TEMP 00h 17h HIGH 0000h
MID 0001h
LOW 0002h
CUSTOM1 0005h
CUSTOM2 0006h
CUSTOM3 0007h
BLACK LEVEL ADJ 00h 1Ch OFF 0000h
LOW 0001h
HIGH 0002h
FILM MODE 00h 1Fh OFF 0000h
AUTO 0001h
ITEM List For Screen
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
ASPECT 00h 20h FULL 0000h Set/Get
NORMAL 0001h
ZOOM 0003h
FULL1 0007h
FULL2 0008h
4:3 0009h
16:9 000Ah
OVER SCAN 00h 23h OFF 0000h
ON 0001h

8VPL Series PROTOCOL MANUAL
ITEM List For Setup
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
INPUT TERMINAL 1 00h 01h VIDEO 0000h Set/Get
SVIDEO 0001h
INPUTA 0002h
INPUTB 0003h
INPUTC 0004h
INPUTD*0005h
INPUTE*0006h
MULTI SCREEN MODE*00h 03h OFF 0000h
TWIN 0001h
INPUT TERMINAL 2*00h 04h VIDEO 0000h Get
SVIDEO 0001h
INPUTA 0002h
INPUTB 0003h
INPUTC 0004h
INPUTD 0005h
INPUTE 0006h
PICTURE MUTING 00h 30h OFF 0000h Set/Get
ON 0001h
INPUT A SIGNAL-SEL 00h 32h AUTO 0000h
COMPUTER 0001h
COMPONENT 0002h
VIDEOGBR 0003h
PICTURE MUTING
MODE
00h 3dh IMAGE 0000h
SHUTTER 0001h
LAMP MODE 00h 40h HIGH 0000h
STANDARD 0001h
LAMP LIGHT MODE 00h 41h AUTO 0001h
FIXED LAMP1 0002h
FIXED LAMP2 0003h
*: VPL-FH500L/F700L only
ITEM List For Infrared Remote Command
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Infrared Remote Command
(15 bit category)
17h Refer to Section
2-1-2.*1
_00h 00h Set only
Infrared Remote Command
(20 bit E category)
19h _00h 00h
Infrared Remote Command
(20 bit EE category)
1Bh _00h 00h
*1: For using this item number, the simulation of the infrared remote controller is enable. Select the corresponding code in the table of
Section 2-1-2 and use it as the lower byte of the item number.
n
Other value is assigned depending for category.

9
VPL Series PROTOCOL MANUAL
ITEM List For Status
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
STATUS ERROR1 01h 01h NO ERROR 00h Get only
LAMP ERROR 01h
FAN ERROR 02h
COVER ERROR 04h
TEMP ERROR 08h
D5V ERROR 10h
POWER ERROR 20h
WARNING TEMP 40h
NVM DATA ERROR 80h
STATUS POWER 01h 02h STANDBY 00h
START UP 01h
STARTUP LAMP 02h
POWER ON 03h
COOLING1 04h
COOLING2 05h
SAVING COOLING1 06h
SAVING COOLING2 07h
SAVING STANDBY 08h
LAMP TIMER 01h 13h VALUE xxh
SUB ROM VERSION 01h 1Dh VALUE xxh
MAIN ROM VERSION 01h 1Eh VALUE xxh
STATUS SECURITY 01h 1Fh DISABLE 00h
ENABLE 01h
STATUS ERROR2 01h 25h NO ERROR 00h
LENS SHUTTER ERROR 01h
Don’t Use 02h
Don’t Use 04h
Don’t Use 08h
Don’t Use 10h
WARNING HIGHLAND 20h
Don’t Use 40h
LAMP SWITCHING
ERROR
80h
NVM DATA VERSION 01h 27h VALUE xxh
LAMP TIMER2 01h 2Bh VALUE xxh
STATUS LAMP 01h 2Dh NO ERROR 00h
LAMP1 NG 01h
LAMP2 NG 02h
ALL LAMP NG 03h

10 VPL Series PROTOCOL MANUAL
VPL-EX100/EX120/EX145/EX175
ITEM List For Picture
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
PICTURE MODE 00h 02h DYNAMIC 0000h Set/Get
STANDARD 0001h
PRESENTATION 0002h
GAME 0003h
LIVING 0004h
CINEMA 0005h
CONTRAST 00h 10h VALUE 0000h-0064h(0-100)
BRIGHTNESS 00h 11h VALUE 0000h-0064h(0-100)
COLOR 00h 12h VALUE 0000h-0064h(0-100)
HUE 00h 13h VALUE 0000h-0064h(0-100)
SHARPNESS 00h 14h VALUE 0000h-0064h(0-100)
VOLUME 00h 16h VALUE 0000h-0064h(0-100)
COLOR TEMP 00h 17h HIGH 0000h
MID 0001h
LOW 0002h
FILM MODE 00h 1Fh OFF 0000h
AUTO 0001h
ITEM List For Screen
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
ASPECT 00h 20h FULL 0000h Set/Get
NORMAL 0001h
ZOOM 0003h
FULL1 0007h
FULL2 0008h
4:3 0009h
16:9 000Ah

11
VPL Series PROTOCOL MANUAL
ITEM List For Setup
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
INPUT TERMINAL 00h 01h VIDEO 0000h Set/Get
SVIDEO 0001h
INPUTA 0002h
INPUTB*0003h
PICTURE MUTING 00h 30h OFF 0000h
ON 0001h
AUDIO MUTING 00h 31h OFF 0000h
ON 0001h
INPUT A SIGNAL-SEL 00h 32h AUTO 0000h
COMPUTER 0001h
COMPONENT 0002h
VIDEOGBR 0003h
LAMP MODE 00h 40h HIGH 0000h
STANDARD 0001h
LOW 0002h
*: This item is disabled for VPL-EX100.
ITEM List For Infrared Remote Command
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Infrared Remote Command
(15 bit category)
17h Refer to Section
2-1-2.*1
_00h 00h Set only
Infrared Remote Command
(20 bit E category)
19h _00h 00h
Infrared Remote Command
(20 bit EE category)
1Bh _00h 00h
*1: For using this item number, the simulation of the infrared remote controller is enable. Select the corresponding code in the table of
Section 2-1-2 and use it as the lower byte of the item number.
n
Other value is assigned depending for category.

12 VPL Series PROTOCOL MANUAL
ITEM List For Status
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Byte
STATUS ERROR1 01h 01h NO ERROR 00h Get only
LAMP ERROR 01h
FAN ERROR 02h
COVER ERROR 04h
TEMP ERROR 08h
D5V ERROR 10h
POWER ERROR 20h
WARNING TEMP 40h
NVM DATA ERROR 80h
STATUS POWER 01h 02h STANDBY 00h
START UP 01h
STARTUP LAMP 02h
POWER ON 03h
COOLING1 04h
COOLING2 05h
SAVING COOLING1 06h
SAVING COOLING2 07h
SAVING STANDBY 08h
LAMP TIMER 01h 13h VALUE xxh
SUB ROM VERSION 01h 1Dh VALUE xxh
MAIN ROM VERSION 01h 1Eh VALUE xxh
STATUS SECURITY 01h 1Fh DISABLE 00h
ENABLE 01h
STATUS ERROR2 01h 25h NO ERROR 00h
Don’t Use 02h
Don’t Use 04h
Don’t Use 08h
Don’t Use 10h
WARNING HIGHLAND 20h
Don’t Use 40h
Don’t Use 80h
NVM DATA VERSION 01h 27h VALUE xxh

13
VPL Series PROTOCOL MANUAL
2-1-2. Infrared Remote Command Code VPL-FH30/FX30/FX35/F400H/F400X/F500X 15bit PROJECTOR
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x
BLACK LEVEL
ADJ TOGGLE
PICTURE
ADJ TOGGLE
1x VOL
LARGE
VOL
SMALL
AUDIO
MUTING
POWER
TOGGLE
CONTRAST
+
CONTRAST
_
COLOR
+
COLOR
_
BRIGHTNESS
+
BRIGHTNESS
_
2x HUE
+
HUE
_
SHARPNESS
+
SHARPNESS
_
PICTURE
MUTING
STATUS
ON
STATUS
OFF
MENU VIDEO INPUT A INPUT B POWER
ON
POWER
OFF
3x CURSOR
→
CURSOR
←
CURSOR
↑
CURSOR
↓
4x PITCH SHIFT 5x INPUT
TOGGLE
ENTER S VIDEO
6x INPUT C 7x INPUT D*TWIN*RESET TEST
PATTERN
*: VPL-FH30/F400H only 20bit PROJECTOR-E
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x
V KEYSTONE
+
V KEYSTONE
_
1x 2x 3x
V KEYSTONE
4x FILM MODE
TOGGLE
5x PICTURE
MODE
DYNAMIC
PICTURE
MODE
STANDARD
PICTURE
MODE
PRESENTATION
PICTURE
MODE
TOGGLE
COLOR
TEMP
TOGGLE
6x APA PHASE FREEZE DIGITAL
ZOOM
+
DIGITAL
ZOOM
_
ASPECT
TOGGLE
7x
20bit PROJECTOR-EE
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x 1x ECO MODE 2x 3x 4x 5x 6x RETURN 7x

14 VPL Series PROTOCOL MANUAL
VPL-FH500L/FX500L/F700HL/F700XL 15bit PROJECTOR
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x
BLACK LEVEL
ADJ TOGGLE
PICTURE
ADJ TOGGLE
1x POWER
TOGGLE
CONTRAST
+
CONTRAST
_
COLOR
+
COLOR
_
BRIGHTNESS
+
BRIGHTNESS
_
2x HUE
+
HUE
_
SHARPNESS
+
SHARPNESS
_
PICTURE
MUTING
STATUS
ON
STATUS
OFF
MENU VIDEO INPUT A INPUT B POWER
ON
POWER
OFF
3x CURSOR
→
CURSOR
←
CURSOR
↑
CURSOR
↓
4x PITCH SHIFT 5x INPUT
TOGGLE
ENTER S VIDEO
6x INPUT C 7x INPUT D*INPUT E*LENS SHIFT
↑
LENS SHIFT
↓
LENS
FOCUS
FAR
LENS
FOCUS
NEAR
LENS ZOOM
LARGE
LENS ZOOM
SMALL
TWIN*RESET TEST
PATTERN
*: VPL-FH500L/F700L only 20bit PROJECTOR-E
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x
V KEYSTONE
+
V KEYSTONE
_
LENS SHIFT
→
LENS SHIFT
←
1x 2x 3x
V KEYSTONE
4x FILM MODE
TOGGLE
5x PICTURE
MODE
DYNAMIC
PICTURE
MODE
STANDARD
PICTURE
MODE
PRESENTATION
PICTURE
MODE
TOGGLE
COLOR
TEMP
TOGGLE
6x APA PHASE LENS ZOOM LENS SHIFT LENS
FOCUS
FREEZE DIGITAL
ZOOM
+
DIGITAL
ZOOM
_
ASPECT
TOGGLE
7x LENS
TOGGLE
20bit PROJECTOR-EE
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x 1x ECO MODE 2x 3x 4x 5x 6x RETURN 7x

15
VPL Series PROTOCOL MANUAL
VPL-EX100/EX120/EX145/EX175 15bit PROJECTOR
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x
BLACK
LEVEL ADJ
TOGGLE
PICTURE
ADJ
TOGGLE
1x VOL
LARGE
VOL:SMALL AUDIO
MUTING
POWER
TOGGLE
CONTRAST
+
CONTRAST
_
COLOR
+
COLOR
_
BRIGHTNESS
+
BRIGHTNESS
_
2x HUE
+
HUE
_
SHARPNESS
+
SHARPNESS
_
PICTURE
MUTING
STATUS
ON
STATUS
OFF
MENU VIDEO INPUT A INPUT B*POWER
ON
POWER
OFF
3x CURSOR
→
CURSOR
←
CURSOR
↑
CURSOR
↓
4x PITCH SHIFT 5x INPUT
TOGGLE
ENTER S VIDEO
6x 7x RESET TEST
PATTERN
*This item is disabled for VPL-EX100. 20bit PROJECTOR-E
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x
V KEYSTONE
+
V KEYSTONE
_
1x 2x 3x
V KEYSTONE
4x FILM MODE
TOGGLE
5x PICTURE
MODE
DYNAMIC
PICTURE
MODE
STANDARD
PICTURE
MODE
PRESENTATION
PICTURE
MODE
LIVING
PICTURE
MODE
GAME
PICTURE
MODE
CINEMA
PICTURE
MODE
TOGGLE
COLOR
TEMP
TOGGLE
6x APA PHASE FREEZE DIGITAL
ZOOM
+
DIGITAL
ZOOM
_
ASPECT
TOGGLE
7x
20bit PROJECTOR-EE
x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF
0x 1x ECO MODE 2x 3x 4x 5x 6x RETURN 7x

16 VPL Series PROTOCOL MANUAL
2-2. Reply
<Table 3>
Item Number Data
Item Data Upper byte Lower byte
ACK Complete 00h 00h
NAK Undefined Command 01h 01h
Size Error 04h
Select Error 05h
Range Over 06h
Not Applicable 0Ah
Check Sum Error F0h 10h
Framing Error 20h
Parity Error 30h
Over Run Error 40h
Other Comm Error 50h
Error description
Check Sum Error
A check sum error occurred.
Framing Error
A framing error occurred.
Parity Error
A parity error occurred.
Over Run Error
An overrun error occurred.
Other Comm Error
Another error occurred.