Sony STR-DA5300ES - Multi Channel Av Receiver User manual

SERVICE MANUAL
AUDIO POWER
SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 −20,000 Hz; rated 120 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
POWER OUTPUT
(US and Canadian models)
Rated Power Output at Stereo Mode1) 2)
(8 ohms 20 Hz −20 kHz,
THD 0.09%):
120 W + 120 W
Reference Power Output at Stereo Mode
(4 ohms 20 Hz −20 kHz,
THD 0.15%):
120 W + 120 W
Reference Power Output
(8 ohms 1 kHz, THD 0.7%)
FRONT2):
130 W + 130 W
CENTER2): 130 W
SURROUND2):
130 W + 130 W
SURROUND BACK2):
130 W + 130 W
Reference Power Output
(4 ohms 1 kHz, THD 0.7%)
FRONT2):
120 W + 120 W
CENTER2): 120 W
SURROUND2):
120 W + 120 W
SURROUND BACK2):
120 W + 120 W
1)Depending on the sound field settings and the
source, there may be no sound output.
2)Measured under the following conditions:
Power requirements: 120 V AC, 60 Hz
(AEP, Russian, Ukrainian and UK models)
Rated Power Output at Stereo Mode1) 2)
(8 ohms 1 kHz, THD
0.7%):
125 W + 125 W
Reference Power Output at Stereo Mode
(4 ohms 1 kHz, THD
0.7%):
125 W + 125 W
Reference Power Output
(8 ohms 20 Hz −20 kHz,
THD 0.09%)
FRONT2):
120 W + 120 W
CENTER2): 120 W
SURROUND2):
120 W + 120 W
SURROUND BACK2):
120 W + 120 W
Reference Power Output
(4 ohms 20 Hz −20 kHz,
THD 0.15%)
FRONT2):
120 W + 120 W
CENTER2): 120 W
SURROUND2):
120 W + 120 W
SURROUND BACK2):
120 W + 120 W
Reference Power Output at Stereo Mode
(8 ohms 1 kHz, THD
10%):
150 W + 150 W
MULTI CHANNEL AV RECEIVER
SPECIFICATIONS
Ver. 1.1 2007.10
– Continued on next page –
9-887-741-02
2007J05-1
© 2007.10
Sony Corporation
Home Audio Division
Published by SonyTechno Create Corporation
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
*Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories.
** Manufactured under license from DTS, Inc.
“DTS”, “DTS-ES” and “Neo:6” are registered trademarks of DTS, Inc. and “DTS-HD Master Audio”,
“DTS-HD High Resolution Audio” and “DTS 96/24” are trademarks of DTS, Inc.
STR-DA5300ES
US Model
Canadian Model
AEP Model
UK Model

2
STR-DA5300ES
Frequency response
Inputs (Analog)
Inputs (Digital)
Outputs
EQUALIZER
FM tuner section
Tuning range 87.5 −108.0 MHz
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
AM tuner section
T
(US and Canadian models)
uning range
With 10-kHz tuning scale
530 −1,710 kHz3)
(AEP, Russian, Ukrainian and UK models)
With 9-kHz tuning scale
531 −1,602 kHz
With 9-kHz tuning scale
531 −1,710 kHz3)
Antenna (aerial) Loop antenna (aerial)
3)
You can change the AM tuning scale to either 9
kHz or 10 kHz. After tuning in any AM station,
turn off the receiver. While holding down
TUNING MODE, press POWER on the receiver.
All preset stations will be erased when you change
the tuning scale. To reset the scale to 10 kHz (or 9
kHz), repeat the procedure.
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
HDMI Video
Input/Output (HDMI Repeater block)
640 ×480p@60Hz
720 ×[email protected]/60Hz
1440 ×[email protected]/60Hz (pixel sent 2times)
1280 ×[email protected]/60Hz
1920 ×[email protected]/60Hz
1920 ×[email protected]/60Hz
720 ×576p@50Hz
1440 ×576p@50Hz (pixel sent 2times)
1280 ×720p@50Hz
1920 ×1080i@50Hz
1920 ×1080p@50Hz
1920 ×1080p@24Hz
PHONO RIAA equalization curve
±0.5 dB
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/DAT, DVD/BD,
T
TAPE/CD-R,
TAPE/CD-R,
V, SAT/CATV,
VIDEO 1/2/3
10 Hz −100 kHz
±3 dB
PHONO Sensitivity: 2.5mV
Impedance: 50kohms
S/N: 90dB (A, 20 kHz
LPF)
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/DAT, DVD/BD, TV,
SAT/CATV,
VIDEO 1/2/3
Sensitivity: 150mV
Impedance: 50kohms
S/N: 100dB (A, 20 kHz
LPF)
DVD/BD, VIDEO 2,
SA-CD/CD (Coaxial) Impedance: 75ohms S/N: 96dB (A, 20 kHz
LPF)
VIDEO 1, TV,
SAT/CATV,
TAPE/CDR,
MD/DAT (Optical)
S/N: 96 dB
(A, 20 kHz LPF)
MD/DAT (REC OUT),
VIDEO 1, ZONE 2,
ZONE 3 (AUDIO OUT)
Voltage:150mV
Impedance: 1kohm
FRONT L/R, CENTER,
SURROUND L/R,
SURROUND BACK L/R,
SUB WOOFER
Voltage: 2V
Impedance: 1kohm
Gain levels ±10 dB, 1 dB step
Reference Power Output at Stereo Mode
(4 ohms 1 kHz, THD
10%):
150 W + 150 W
Reference Power Output
(8 ohms 1 kHz, THD 10%)
FRONT2):
150 W + 150 W
CENTER2):
150 W
SURROUND2):
150 W + 150 W
SURROUND BACK2):
150 W + 150 W
Reference Power Output
(4 ohms 1 kHz, THD 10%)
FRONT2):
150 W + 150 W
CENTER2):
150 W
SURROUND2):
150 W + 150 W
SURROUND BACK2):
150 W + 150 W
1)
Depending on the sound field settings and the
source, there may be no sound output.
2)
Measured under the following conditions:
Power requirements: 230 V AC, 50/60 Hz
(in countries/area in Europe
other than the U.K.)
240 V AC, 50/60 Hz
(in the U.K. and general area)
General
Power requirements 120 V AC, 60 Hz (US and
Canadian models)
Power output (DIGITAL MEDIA PORT)
DC OUT:5 V, 700 mA
Power consumption 480 W/580 VA (US/
480 W (AEP, Russian,
Ukrainian and UK models)
Canada)
Power consumption (during standby mode)
0.7 W (when “HDMI
Control” and “RS-232C
Control” is set to “OFF”)
Dimensions 430 ×175 ×430 mm
(width/height/depth)
including projecting parts
and controls
Mass (Approx.) 16.0 kg
Supplied accessories
Operating Instructions
Quick Setup Guide (1)
HDMI CONTROL Guide (1)
GUI Menu List (1)
Optimizer microphone ECM-AC1 (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
AC power cord (mains lead) (1)
Remote commander RM-AAL008 (1) (US and
Canadian models)
Remote commander RM-AAL009 (1) (AEP,
Russian, Ukrainian and UK models)
Remote commander RM-AAU016 (1)
R6 (size-AA) batteries (4)
Design and specifications are subject to
change without notice.
230 V AC, 50/60Hz
(in countries/area in
Europe other than the U.K.)
230 −240V AC, 50/60Hz
(in the U.K. and general
area)
Ver. 1.1

3
STR-DA5300ES
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals,metal trim, “metallized” knobs, screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operatedACvoltmeter.The “limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2VAC range are suitable. (See
Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µ FAC
voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
TABLE OF CONTENTS
1. SERVICING NOTES .............................................. 5
2. GENERAL .................................................................. 11
3. DISASSEMBLY
3-1. Disassembly Flow .......................................................... 19
3-2. Case ................................................................................ 20
3-3. SP-TM Board, Tuner (FM/AM) ..................................... 20
3-4. D-CONNECT Board, DSP Board, DIGITAL Board,
CIS Board and CONTROL Board.................................. 21
3-5. D-VIDEO Board............................................................. 21
3-6. Front Panel Section ........................................................ 22
3-7. S-VIDEO Board and A-VIDEO Board .......................... 22
3-8. FLI-1.8REG Board and ANALOG Board...................... 23
3-9. Power Transformer (T001), E-VOL Board and
MAIN Board................................................................... 24
3-10. Heat Sink Section ........................................................... 25
4. TEST MODE............................................................. 26
5. ELECTRICAL ADJUSTMENTS ........................ 30
6. DIAGRAMS
6-1. Block Diagram – CONTROL Section –.......................... 33
6-2. Block Diagram – DSP Section – ..................................... 34
6-3. Block Diagram – DIGITAL AUDIO Section – ............... 35
6-4. Block Diagram – HDMI Section (1/2) – ......................... 36
6-5. Block Diagram – HDMI Section (2/2) – ......................... 37
6-6. Block Diagram – VIDEO PROCESS Section – .............. 38
6-7. Block Diagram – ANALOGAUDIO Section – .............. 39
6-8. Block Diagram – POWER AMP Section – ..................... 40
6-9. Block Diagram – VIDEO Section (1/2) – ....................... 41
6-10. Block Diagram – VIDEO Section (2/2) – ....................... 42
6-11. Block Diagram – PANEL, CIS, XM/
SIRIUS RECEIVER, DMPORT Section – ..................... 43
6-12. Block Diagram – POWER SUPPLY Section – ............... 44
6-13. Printed Wiring Board
– MAIN Board (Component Side) – ............................... 46
6-14. Printed Wiring Board
– MAIN Board (Conductor Side) – ................................. 47
6-15. Schematic Diagram – MAIN Board (1/4) – .................... 48
6-16. Schematic Diagram – MAIN Board (2/4) – .................... 49
6-17. Schematic Diagram – MAIN Board (3/4) – .................... 50
6-18. Schematic Diagram – MAIN Board (4/4) – .................... 51
6-19. Printed Wiring Board
– DIGITAL Board (Component Side) – .......................... 52
6-20. Printed Wiring Board
– DIGITAL Board (Conductor Side) –............................ 53
6-21. Schematic Diagram – DIGITAL Board (1/4) – ............... 54
6-22. Schematic Diagram – DIGITAL Board (2/4) – ............... 55
6-23. Schematic Diagram – DIGITAL Board (3/4) – ............... 56
6-24. Schematic Diagram – DIGITAL Board (4/4) – ............... 57
6-25. Printed Wiring Board – DSP Board (Side A) – ............... 58
6-26. Printed Wiring Board – DSP Board (Side B) – ............... 59
6-27. Schematic Diagram – DSP Board (1/4) – ....................... 60
6-28. Schematic Diagram – DSP Board (2/4) – ....................... 61
6-29. Schematic Diagram – DSP Board (3/4) – ....................... 62
6-30. Schematic Diagram – DSP Board (4/4) – ....................... 63
6-31. Printed Wiring Board
– ANALOG Board (Component Side) – ......................... 64
6-32. Printed Wiring Board
– ANALOG Board (Conductor Side) – ........................... 65
6-33. Schematic Diagram – ANALOG Board (1/3) – .............. 66
6-34. Schematic Diagram – ANALOG Board (2/3) – .............. 67
6-35. Schematic Diagram – ANALOG Board (3/3) – .............. 68

4
STR-DA5300ES
6-92. Printed Wiring Board – AC Board (TYPEA) – ............. 124
6-93. Printed Wiring Board – AC Board (TYPE B) – ............. 124
6-94. Schematic Diagram – AC Board – ................................. 125
7. EXPLODED VIEWS
7-1. Case Section ................................................................... 173
7-2. DIGITAL Board Section ................................................ 174
7-3. D-VIDEO Board Section................................................ 175
7-4. DISPLAY Board Section................................................ 176
7-5. Front Panel Section ........................................................ 177
7-6. A-VIDEO Board Section................................................ 178
7-7. ANALOG Board Section ............................................... 179
7-8. Heat Sink Section ........................................................... 180
7-9. MAIN Board Section...................................................... 181
8. ELECTRICAL PARTS LIST............................... 182
6-36. Printed Wiring Board – E-VOL Board – ......................... 69
6-37. Schematic Diagram – E-VOL Board (1/2) – ................... 70
6-38. Schematic Diagram – E-VOL Board (2/2) – ................... 71
6-39. Printed Wiring Boards – CONNECTOR Section –......... 72
6-40. Schematic Diagram – CONNECTOR Section – ............. 73
6-41. Printed Wiring Board
– TEMPERATURE DETECTION Board – .................... 74
6-42. Schematic Diagram
– TEMPERATURE DETECTION Board – .................... 74
6-43. Printed Wiring Board – A-CLASS AMP Board – ........... 75
6-44. Schematic Diagram – A-CLASS AMP Board (1/2) – ..... 76
6-45. Schematic Diagram – A-CLASS AMP Board (2/2) – ..... 77
6-46. Printed Wiring Board
– POWER AMPLIFIER Board – .................................... 78
6-47. Schematic Diagram – POWERAMPLIFIER Board – .... 79
6-48. Printed Wiring Board – PROTECTOR (F-C) Board – .... 80
6-49. Schematic Diagram – PROTECTOR (F-C) Board –....... 81
6-50. Printed Wiring Boards
– PROTECTOR (SB/SURR) Section – ........................... 82
6-51. Schematic Diagram
– PROTECTOR (SB/SURR) Section – ........................... 83
6-52. Printed Wiring Board – BIAS Board –............................ 84
6-53. Schematic Diagram – BIAS Board – .............................. 85
6-54. Printed Wiring Board – SP-TM Board – ......................... 86
6-55. Schematic Diagram – SP-TM Board – ............................ 87
6-56. Printed Wiring Board
– D-VIDEO Board (Component Side) – ......................... 88
6-57. Printed Wiring Board
– D-VIDEO Board (Conductor Side) – ........................... 89
6-58. Schematic Diagram – D-VIDEO Board (1/12) – ............ 90
6-59. Schematic Diagram – D-VIDEO Board (2/12) – ............ 91
6-60. Schematic Diagram – D-VIDEO Board (3/12) – ............ 92
6-61. Schematic Diagram – D-VIDEO Board (4/12) – ............ 93
6-62. Schematic Diagram – D-VIDEO Board (5/12) – ............ 94
6-63. Schematic Diagram – D-VIDEO Board (6/12) – ............ 95
6-64. Schematic Diagram – D-VIDEO Board (7/12) – ............ 96
6-65. Schematic Diagram – D-VIDEO Board (8/12) – ............ 97
6-66. Schematic Diagram – D-VIDEO Board (9/12) – ............ 98
6-67. Schematic Diagram – D-VIDEO Board (10/12) – .......... 99
6-68. Schematic Diagram – D-VIDEO Board (11/12) – ......... 100
6-69. Schematic Diagram – D-VIDEO Board (12/12) – ......... 101
6-70. Printed Wiring Board
– A-VIDEO Board (Component Side) – ........................ 102
6-71. Printed Wiring Board
– A-VIDEO Board (Conductor Side) – .......................... 103
6-72. Schematic Diagram – A-VIDEO Board (1/4) – ............. 104
6-73. Schematic Diagram – A-VIDEO Board (2/4) – ............. 105
6-74. Schematic Diagram – A-VIDEO Board (3/4) – ............. 106
6-75. Schematic Diagram – A-VIDEO Board (4/4) – ............. 107
6-76. Printed Wiring Board – S-VIDEO Board – .................... 108
6-77. Schematic Diagram – S-VIDEO Board –....................... 109
6-78. Printed Wiring Board – VIDEO3 Board –...................... 110
6-79. Schematic Diagram – VIDEO3 Board – ........................ 111
6-80. Printed Wiring Board
– CONTROL Board (Component Side) – ...................... 112
6-81. Printed Wiring Board
– CONTROL Board (Conductor Side) – ........................ 113
6-82. Schematic Diagram – CONTROL Board (1/2) – ...........114
6-83. Schematic Diagram – CONTROL Board (2/2) – ...........115
6-84. Printed Wiring Board – CIS Board –.............................. 116
6-85. Schematic Diagram – CIS Board – ................................ 117
6-86. Printed Wiring Board – DISPLAY Board – ................... 118
6-87. Schematic Diagram – DISPLAY Board – ...................... 119
6-88. Printed Wiring Boards – PANEL Section –.................... 120
6-89. Schematic Diagram – PANEL Section –........................ 121
6-90. Printed Wiring Board – DC-DC Board – ....................... 122
6-91. Schematic Diagram – DC-DC Board – .......................... 123
Note 1:Refer “NOTE WHEN THE AC BOARD IS REPAIRED”
(page 5) in servicing notes for how to distinguish TYPE
A/B.
Ver. 1.1
Note 2:Referto SUPPLEMENT-1fortheCONTROL,DIGITAL and
DSPboardsofprinted wiringboards,schematic diagrams
and electrical parts list of Russian and Ukrainian models.
When repairing the set of US, Canadian, AEP and UK
models,referto either oforiginal servicemanual/SUPPLE-
MENT-1 according to the set.

5
STR-DA5300ES
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE OF REPLACING THE IC3601 ON THE
D-VIDEO BOARD
Replacement of IC3601 on the D-VIDEO board used in this set
requires a special tool.
NOTE WHEN THE AC BOARD IS REPAIRED
(US and Canadian models only)
Note: AEP, Russian, Ukrainian and UK models uses only TYPE B.
Two types exist in theAC board for US and Canadian models.
Repair after distinguishing which type it is referring to the figure
below.
•MODEL IDENTIFICATION
Model PART No.
US and Canadian models 3-113-954-1[]
AEP model 3-113-954-2[]
UK model 3-113-954-3[]
Russian and Ukrainian models 3-113-954-4[]
PART No.
– Back Panel –
NOTE OF REPLACING THE IC3511 AND IC3513 ON
THE D-VIDEO BOARD
IC3511 and IC3513 on the D-VIDEO board cannot exchange with
single. When IC3511 and IC3513 on the D-VIDEO board are
damaged, exchange the entire mounted board.
NOTE OF REPLACING THE IC5002 AND IC5202 ON
THE DSP BOARD
IC5002 and IC5202 on the DSP board cannot exchange with single.
WhenIC5002andIC5202 on the DSP boardaredamaged,exchange
the entire mounted board.
– AC Board (Component Side) –
JW003
TYPE A : JW003 is not mounted.
TYPE B : JW003 is mounted.
Ver. 1.1

6
STR-DA5300ES
for PC
J1499
UPDATE OF SOFTWARE OF IC2003 ON THE CONTROL BOARD, IC3610 ON THE D-VIDEO BOARD AND
IC5208 ON THE DSP BOARD
Perform operation of the following when the update of software of the IC2003 on the CONTROL board, IC3610 on the D-VIDEO board and
IC5208 on the DSP board is necessary.
Connect:
Procedure:
1. Connect J1499 on the MAIN board and PC by using the RS-232C cable.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J1499 on the MAIN board and PC.
ERROR MESSAGES
If there is a malfunction, the display shows a code of two numbers and a message. You can check the condition of the system by the
message. Refer to the following table to solve the problem.
messages cause and response
PROTECTOR Irregular current is output to the speakers, or the upper panel of the receiver is covered with something.
The receiver will automatically turn off after a few seconds. Cheack the speakers connection and turn
on the power again.

7
STR-DA5300ES
POWER AMP BLOCK SERVICE POSITION
In checking the PowerAMP block, prepare jig (extension cable J-2501-291-A: 2 mm Pitch, 12 cores, Length 300 mm/J-2501-311-A: 2 mm
Pitch, 15 cores, Length 300 mm).
insulating sheet
Connect the extension jig (J-2501-311-A) to the
A-CLASS AMP board (CN1505) and
CONNECTOR 1 board (CN1206).
CONNECTOR 2 board
(CN1206)
A-CLASS AMP board
(CN1505)
power AMP Block
Connect the extension jig (J-2501-291-A) to the
A-CLASS AMP board (CN1504) and
CONNECTOR 2 board (CN1207).
CONNECTOR 1 board
(CN1207)
A-CLASS AMP board
(CN1504)
CONTROL BOARD SERVICE POSITION
In checking the CONTROL board, prepare jig (extension cable J-2501-255-A: 1.25 mm Pitch, 10 cores, Length 300 mm/J-2501-258-A: 1.25
mm Pitch, 16 cores, Length 300 mm/J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-260-A: 1.25 mm Pitch, 20 cores,
Length 300 mm).
connect jig (extension cable J-2501-260-A)
to the CONTROL board (CN2006)
and MAIN board (CN1005).
connect jig (extension cable J-2501-255-A)
to the CONTROL board (CN2008)
and MAIN board (CN1006).
connect jig (extension cable J-2501-258-A)
to the CONTROL board (CN2004)
and D-CONNECT board (CN2403).
CONTROL board
(CN2006)
connect jig (extension cable J-2501-259-A)
to the CONTROL board (CN2005)
and D-CONNECT board (CN2405).
CONTROL board
(CN2008)
MAIN board
(CN1006)
MAIN board
(CN1005)
CONTROL board
(CN2004)
CONTROL board
(CN2005)
D-CONNECT board
(CN2403)
D-CONNECT board
(CN2405)
insulating sheet

8
STR-DA5300ES
DIGITAL BOARD SERVICE POSITION
In checking the DIGITAL board, prepare jig (extension cable J-2501-312-A: 1.25 mm Pitch, 11 cores, Length 300 mm).
D-VIDEO/S-VIDEO BOARDS SERVICE POSITION
In checking the D-VIDEO board, prepare jig (extension cable J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-313-A: 1.25
mm Pitch, 17 cores, Length 300 mm).
connect jig (extension cable J-2501-312-A)
to the DIGITAL board (CN2203)
and CONTROL board (CN2002).
CONTROL board
(CN2002)
DIGITAL board
(CN2203)
Connect jig (extension cable J-2501-259-A)
to the D-VIDEO board (CN3507) and
CONTOL board (CN2001).
CONTROL board
(CN2001)
D-VIDEO board
(CN3507)
Connect jig (extension cable J-2501-313-A)
to the D-VIDEO board (CN3508) and
CONTOL board (CN2009).
CONTROL board
(CN2009)
D-VIDEO board
(CN3508)
S-VIDEO board

9
STR-DA5300ES
A-VIDEO BOARD SERVICE POSITION
In checking the A-VIDEO board, prepare jig (extension cable J-2501-257-A: 1.25 mm Pitch, 14 cores, Length 300 mm).
ANALOG BOARD SERVICE POSITION
In checking the ANALOG board, prepare jig (extension cable J-2501-258-A: 1.25 mm Pitch, 16 cores, Length 300 mm).
connect jig (extension cable J-2501-257-A)
to the CONTROL board (CN2010) and A-VIDEO board (CN6507).
A-VIDEO board
(CN6507)
CONTROL board
(CN2010)
insulating sheet
connect jig (extension cable J-2501-258-A)
to the CONTROL board (CN2011) and ANALOG board (CN602).
ANALOG board
(CN602)
CONTROL board
(CN2011)
insulating sheet

10
STR-DA5300ES
LEAD WIRE SETTING
insulating sheet
MAIN board
In checking the board, make two
capacitors discharge for electric
shock prevention.(R: 800
Ω /2W)
C2490
C2490
C2491
C2491
CAUTION
MAIN BOARD SERVICE POSITION
heat sink
The lead wire must not come in contact with the transformer and the heat sink.
transformer
Please band together so that a primary side cable
cannot touch a power transformer and heat sink.