Sony D-WDR / 3D DNR User manual

8-007-06
D-WDR/3D DNR DOME CAMERA
630 TVL
D-WDR / 3D DNR
DOME CAMERA
USER’S MANUAL
■
■
Sony 1/3” Super HAD CCD II
High Resolution 630TV Lines
■
■
■
■
■
■
■
■
■
■
D-WDR(Wide Dynamic Range)
3D DNR(Digital Noise Reduction)
LSC(Lens Shading Compensation)
Sens-Up Function(x1024)
Back Light Compensation
Day & Night (ICR-Optional)
Intelligebt Motion Detection
PELCO-D / RS485(Option)
Privacy Mask(Polygonal,8 Colors)
O.S.D menu function

The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This installation should be made by a qualified service person
and should conform to all local codes.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.

Precaution
Do not install the camera in
extreme temperature conditions.
To avoid malfunctions, never
use the camera close to a gas
or oil leak
Do not Keep the camera face to
strong light directly
Do not disassemble the camera
even if troubles happened
Do not drop the camera or
subject them to physical shocks.
Do not install the camera under
unstable lighting conditions
Do not install or use the camera
in an environment where the
humidity is high
Do not expose the camera to
rain or spill beverage on it.

1. Features
D-WDR(Wide Dynamic Range)
Delivers a powerful Wide Dynamic Range to the camera to provide D-WDR captures
the images at all light levels by correcting GAMMA CURVE. If you use an ordinary
camera in a scene with an intensive backlight, the object will be displayed dark on
the monitor affected by the backlight.To solve this problem, you can use the D-WDR
function to improve the dark part without saturation from bright part.
You can adjust SET LEVEL to get clearer images.
630 TVL ULTRA HIGH RESOLUTION
The horizontal resolution is 630 TV Lines in Color mode and 700 TV Lines in Black/
White mode using a high density CCD. It gives a vivid image output with super
high horizontal resolution using our own De-Mosaic Interpolation algorithm and a
specialised built-in sharpness filter.
3D DNR(Digital Noise Reduction)
Achieves excellent 3D-DNR (3 Dimensional-Digital Noise Reduction)
function very excellently by using upgraded 3D filtering and enables to keep this
function automatically while operating the camera to provide the clear and superior
images in very low light luminance.The SAMRT 3D-DNR will be work automatically if
There is any movement or motion. Also, this can be focus on the object in reduce the
“Ghost Effect”caused by moving object to it self.
Smart IR Function
LSC ( Lens Shading Compensation)
Sens-Up(x1024)
Achieves high quality pictures by supporting a long exposure time - more than
1/50second - and enables recognition of the shape and color of a suspended
object under no light conditions
POLYGONAL PRIVACY MASKING(Polygonal, 8colors)
Ensures privacy protection for private and specific areas on the video signal
output using a polygonal masking function. It allows the size and position of the
masking areas to be controlled very easily, and there are 8 mask areas which are
user programmable - color, brightness and mosaic.
HLC
Enables the recognition of a visible car license plate by blocking unwanted light
sources.
HIGH SENSITIVITY TRUE DAY&NIGHT
The Day & Night function delivers high quality color rendition and converts
automatically into monochrome as luminance levels drop.

FOCUS
ZOOM
⑤
④
3. Names and Functions of Parts
②
②
②
②
①
③
③
①⑥
①
①
IR LED Type
Non IR LED Type
DIMESION:145( Ø) x 106(H)mm
DIMESION:145(
Ø) x 106(H)mm
DIMESION:144(
Ø) x 103(H)mm
DIMESION:144(
Ø) x 103(H)mm

3. Components
①Base
②Dome Cover Ring
③ IR LEDs
④ Focus Handle
Used to provide for accurate of an object within the
lens field of view
⑤ Zoom Handle
Used to adjustzoom magnification by turning
⑥OSD Board
Service Video
WDR/3D DNR DOME CAMERA
WDR / 3D DNR
DOME CAMERA
USER’S MANUAL
WDR/3DDNR
ZeroDefect
HighResolution of 600 TV Lines
SensUp(x512, DSS)
DIS(DigitalImage Stabilization)
PolygonalPrivacy Masking
D.Zoom(x1~x10)
Eclipse
HighSensitivity Day&Night
Option
CEILING PAD
SCREW
MANUAL
L-WRENCHSERVICE VIDEO
SERVICE VIDEO
RS-485
Terminal Block
WDR/3D DNR DOME CAMERA
WDR / 3D DNR
DOME CAMERA
USER’S MANUAL
WDR/3DDNR
ZeroDefect
HighResolution of 600 TV Lines
SensUp(x512, DSS)
DIS(DigitalImage Stabilization)
PolygonalPrivacy Masking
D.Zoom(x1~x10)
Eclipse
HighSensitivity Day&Night
SCREW
DOME COVER OPENER
MANUAL
Option
RS-485
Terminal Block
DOWN RIGHT
LEFT ENTER UP

4. Installation & Connection
Wall
Note :
* Ceiling pad(gasket) should be sticked to above base in installation
place.
* Wall mounting backet and other instruments should be used
with dome camera if the installation condition is not appropriate
to cover the whole dome base.
Wall
Plastic Dome CameraVandalproof Dome Camera

DC Power Connecting
Monitor
Power
(Adaptor Plug)
Adaptor
Video Cable
DVR
RS485 +
RS485 -(White)
RS485 +(Orange)
(Option)
RS485 -
PORT2
TX
+
_+ _+ _+ _
RX TX RX
PORT1
AC Power Connecting
Monitor
Adaptor
Video Cable
DVR
RS485 +
RS485 -(White)
Power
RS485 +(Orange)
(Option)
RS485 -
PORT2
TX
+
_+ _+ _+ _
RX TX RX
PORT1
+

5. Setup Menu Flow
EXPOSURE LENS DC, MANUAL
AGC OFF,LOW,MID,HIGH
SENSE-UP AUTO, OFF, X2, X4, X8, X16, X32, X64,
X128, X256, X512, X1024
BACK LIGHT OFF
BLC - BLC LEVEL<OFF, LOW, MID, HIGH>
HLC
D-WDR-SET LEVEL<0~20>
3D-DNR OFF, LOW, MID, HIGH, AUTO
RETURN
WHITE BALANCE WB MODE ATW, MANUAL, PUSH
R-Y GAIN
B-Y GAIN
RETURN
DAY&NIGHT D&N MODE AUTO, COLOR, B&W, EXT, EXT2
BURST ON, OFF
C_SUP <0 ~ 100>
S_SUP <0 ~ 100>
SMART IR ON, OFF
RETURN
IMAGE ADJUST MIRROR OFF, MIRROR
SHARPNESS <0~30>
GAMMA 0.45, 0.55, 0.65, USER<0.2 ~ 1.0>
LSC OFF, ON <0 ~ 30>
MONITOR CRT, LCD
RETURN
MOTION MOTION OFF, ON
AREA AREA1 ~ AREA4
SENSITIVITY <1 ~ 30>
DISPLAY OFF, MESSAGE, TRACE
HOLD TIME <0~15>
ALARM OUTPUT OFF, ON
RETURN

PRIVACY MASK1 OFF
ON
DOT SEL
DOT XY
MOVE XY
COLOR SET<1~8>
MASK8 OFF
ON
DOT SEL
DOT XY
MOVE XY
COLOR SET<1~8>
RETURN
SPECIAL LANGUAGE 9 Language
TITLE
COMMUNICATION OFF
ON
ID<0 ~ 255>
BAUD RATE<2400, 4800, 9600>
PROTOCOL<PELCO-D>
DPC OFF, AUTO
FACTORY SET NO, YES
RETURN
EXIT SAVE&EXIT
EXIT
RETURN

6. Special Features
1. LENS
PRIVACY MASK1 OFF
ON
DOT SEL
DOT XY
MOVE XY
COLOR SET<1~8>
MASK8 OFF
ON
DOT SEL
DOT XY
MOVE XY
COLOR SET<1~8>
RETURN
SPECIAL LANGUAGE 9 Language
TITLE
COMMUNICATION OFF
ON
ID<0 ~ 255>
BAUD RATE<2400, 4800, 9600>
PROTOCOL<PELCO-D>
DPC OFF, AUTO
FACTORY SET NO, YES
RETURN
EXIT SAVE&EXIT
EXIT
RETURN
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY & NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
EXPOSURE
LENS DC
AGC MID
SENS-UP AUTO
BACK LIGHT D-WDR
3D-DNR AUTO
RETURN
Select the connected lens type DC or ELC by using the
LEFT / RIGHT buttons.
* To use the functions of this camera effectively a DC type Auto Iris
lens is recommended.
* Some lenses may not work properly, depending on the
setting of the DC level in the EXPOSURE.
* Please note that you should set the lens type ELC in the
EXPOSURE menu when using a fixed lens.
- Using this function, you can control brightness level.
DC <1~100>, ELC <1~100>
2. SENS UP
You can get a clear image with this function, even at night or
at low lighting levels.
-AUTO, OFF, X2~X1024
Note : Ghost is increased according to the SENS-UP level(x2~x1024 )
* Note that higher SENS-UP level, the brigher the screen, but there
will be a more likely ghosting effect.

3. D-WDR(Wide Dynamic Range)
D-WDR captures the images at all light levels by correcting GAMMA CURVE.
If you use an ordinary camera in a scene with an intensive backlight,
the object will be displayed dark on the monitor affected by the backlight.
To solve this problem, you can use the D-WDR function to improve the dark
part without saturation from bright part.
You can adjust SET LEVEL to get clearer images.
4. HLC
This function is to mask the bright color.
You can select 4 mask areas and DAY&NIGHT and adjust HLC level.
EXPOSURE
LENS DC
AGC MID
SENS-UP AUTO
BACK LIGHT D-WDR
3D-DNR AUTO
RETURN
D-WDR
SET LEVEL 003
RETURN
EXPOSURE
LENS DC
AGC MID
SENS-UP AUTO
BACK LIGHT HLC
3D-DNR AUTO
RETURN
HLC
HBLC MANUAL
MODE ALL DAY
HLC LEVEL 003
MASK1 ON
MASK2 ON
MASK3 ON
MASK4 ON
RETURN

5. 3D DNR(Digital Noise Reduction)
Select 3D DNR ON or OFF.
3D-DNR function reduce the background noise in a low luminance
environment. Upgraded 3D filtering ensures even more clear image.
[DNR Level High : Picture image is more clear but Ghost is more increased.
DNR Level Low : Picture image is not clear but less Ghost.]
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY & NIGHT
MOTION
IMAGE ADJUST
PRIVACY
SPECIAL
EXIT
EXPOSURE
LENS DC
AGC MID
SENS-UP AUTO
BACK LIGHT D-WDR
3D-DNR AUTO
RETURN
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY & NIGHT
MOTION
IMAGE ADJUST
PRIVACY
SPECIAL
EXIT
DAY & NIGHT
D&N MODE AUTO
BURST OFF
C_SUP 060
A_SUP 045
SMART IR OFF
RETURN
6. DAY & NIGHT
Selectable AUTO, COLOR, B&W, EXT, EXT2(not use)
- AUTO : The camera switch Color to B/W or B/W to Color
automatically by ambient illumination.
- COLOR : The picture is always displayed in Color
- B&W : The picture is always displayed in B/W
- EXT : Switch day or night by external CDS sensor for
true day&night (ICR / Lens ICR)

7. SMART MOTION
With learning capability, it memorizes the previous screen on the
movement of the subject approximately in 3 to 5 seconds. When
there is a change, the alarm function goes off.
6-1. BURST
Select BURST ON or OFF
6-2. C_SUP : Color Suppression
You can set the level(0~100)
This is a level to make the Color suppression
6-3. A_SUP : Aperture Suppression
You can set the level()~100)
This is a level to make the Aperture suppression
6-4 SMART IR ON/OFF
Select SMART IR ON or OFF
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY & NIGHT
MOTION
IMAGE ADJUST
PRIVACY
SPECIAL
EXIT
MOTION
MOTION
AREA
SENSITIVITY
HOLD TIME
DISPLAY
ALARM OUTPUT
RETURN
ON
003
007
TRACE
OFF

7. SPECIFICATIONS
TV System
Sensor
Total Pixels
Effective Pixels
Synchronization
Scanning System
Horizontal Resolution
Min. Illumination Sens-Up Off
Sens-Up On
Video Output
γCorrection
Monitor
S/N
O.S.D
Electrical Shutter
Privacy Masking
Day & Night
Motion Detection
Sens-Up(Low Shutter)
Language
White Balance
D-WDR
Mirror
3D-DNR
LSC
Smart IR
Day & Night System
IR LED
Night View Distance
Lens
Lens(optional)
Operating Temperature/Humidity
Storage Temperature/Humidity
Power(Max.) DC Type
DC/AC Type
NTSC PAL
Sony 1/3” Super HAD CCD II
(H)811 x (V)508 (H)795 x (V)596
(H)768 x (V)494 (H)752 x (V)582
H/V 15.734/59.94Hz H/V 15.625/50Hz
2:1 Interlace
630 TV Lines(Max.) / 700 TV Lines(B/W)
0.12 Lux(15IRE), 0.2Lux(30IRE), 0.4Lux(50IRE) F1.2
0.0002Lux(15IRE), 0.0005Lux(30IRE), 0.0008Lux(50IRE) F1.2
1.0Vp-p/75ohm Video 0.71Vp-p
0.45, 0.55, 0.65, USER
CRT, LCD
More than 52dB (AGC off)
LENS, AGC, SENS-UP, BACK LIGHT(BLC, HLC, D-WDR),
3D-DNR, WHITE BALANCE, DAY & NIGHT
MIRROR, SHARPNESS, GAMMA, MONITOR, LSC,
MOTION, PRIVACY (MASK1 ~MASK8), LANGUAGE
COMMUNICATION, DPC
1/60~1/100,000 1/50~1/100,000
8 Windows(Polygonal, 8 Colors)
AUTO, COLOR, BW, EXT, EXT2
ON / OFF
AUTO, OFF~x1024
9 Language
ATW / MANUAL / PUSH
ON / OFF (WDR LEVEL)
ON / OFF
OFF, LOW, MID, HIGH, AUTO
ON / OFF
ON / OFF
ICR (Optional)
IR LED Type Non IR LED Type
30 units
Outdoor 25m
2.8~12mm DC Iris Varifocal Lens
2.8~12mm Varifocal Lens
-20 ~60 / 30% ~80%
-30~60 / 20% ~90%
DC 12V 450mA DC 12V 120mA
DC 12V 550mA, AC 24V 250mA DC 12V 200mA, AC 24V 80mA
[Recommended-Voltage : +/- 20%, Current:
Adapter with rated power of 2 times(than real using current]
Design and specifications are subject to change without notice

PRODUCT WARRANTY CARD
1) ITEM # :
2) S/N # :
3) INSTALLATION CONDITION
- Indoor  / Outdoor 
- Power supply SPECIFICATION :
DC12V  / AC24V 
CURRENT __________ mA
4) TROUBLESHOOTING
- No picture 
- Bad image 
- No power 
- Water damage 
- LED ON  / OFF 
- ETC.  :
* Please keep this warranty card with the manual.
* Please fill out this warranty card and send us this warranty card
with the faulty units together.
Following cases can be charged even within the warrany period.
a. When defects are caused by user’s carelessness.
b. When improper or unauthorized repairs are done or when the inside is
modified or damaged.
c. Defects caused by natural disaster or power problem.
d. When the warranty card is not filled out or corrected unconfirmed.