Sony SST-6420 User manual

OPERATING MANUAL
Before attempting to connect or operate this product, please read these
nstructions completelyi
OKIUSA Standard Camera
1/3” SONY Super HAD CCD
1. General
This color video camera employs 1/3 inch charge coupled imaging device with
310/270 k picture elements and equipped with Digital Signal Processor for
video signal processing, to provide high quality stable picture.
2. Features
1. Resolution: 420 TV lines of horizontal resolution.
2. Low Lux: BY employing high sensitivity image sensor and low noise circuit
design produces 0.8 Lux and signal-to-noise ratio of 48 dB.
3. White Balance: The wide range of Auto Wide Balance (AWB) and Auto
Tracing White Balance (ATW) allow the camera to adjust automatically the
tone according to the color temperature of the light source illuminating the
subject.
4. Back Light Compensation: Smart digital control Auto BLC, ensure for use
against any unusual lighting conditions.
5. Auto Gain Control: Advanced Super AGC and auto gain control function
built-in.
6. Internal sync.
Model SST-6420 12V DC
Model SST-6420D 12V DC + 24V AC
Model SST-6420P 85 ~ 265V AC
-1 -

3. Name of parts and functions
A C 24V
DC 12V
PL
VI DE O O U T
A C 85V ~ 265V
VI DE O O U T
PL
DC 12V
VI DE O O U T
PL
BLCOFF
SUPAG C
AE AI
ATW
BLC
AGC
AWB
FLO FF FLO N
AI
FLO N
SUPAG C
AWB
BLCOFF
ATW
AGC
BLC
AE
FLO FF
BLCOFF
AWB
SUPAG C
FLO N
AI
AGC
ATW
FLO FF
AE
BLC
DC V IDE O
DC LEVEL
DIGITAL
DCBA
EF
G
J
H
K
L
SST-6420P
SST-6420D
SST-6420
A. C（CS）mount adapter
If a CS mount lens is to be used, remove the C mount ring.
B. DC lever Adjuster（VR）
For DC drive auto iris lens driving level adjustment; in order to obtain
correct exposure light.
C. Auto iris lens connector（MINI JACK）See 3-1 auto-iris connector.
DC VIDEO
D. Video/DC auto-iris lens selector
DC—For DC Drive lens
Video—For Video drive lens
E. Flange focal lock screw
F. Holder screw hole
Standard photographic pan-head screw size（1/4”-20）
G. Dip Switch
BLCOFF
AW B
SUP AG C
FLO N
AI
AGC
ATW
FLOFF
AE
BLC
AE /A I O PTIO N
WB MODE
AG C M OD E
BLC FUNC TIO N
FLI CKERLESS FUNCTIO N
H. Video output terminal（BNC）
This connector is used to connect with the VIDEO IN connector of monitor.
-2 -

I. Power pilot LED
J. AC85V~265V Power Cord
K. DC 12V or AC24V/DC 12V Block Terminal
L. DC 12V power input terminal
1
2
3
4
DC 12V
3.1 Auto Iris Lens Connector
●Use the accompanying auto iris lens control connector plug.
For auto iris lens with built-in EE amp.（VIDEO Type）
Set the lens selector switch to “Video” position.
Connector cable leads
1.Red----power 2.NC
3.White----video 4.Black----shielded
For auto iris lens without EE amp.（DC Type）
This is the view from external of camera
Set the lens selector switch to “DC” position.
Connector cable leads
1.Damping coil（－） 2.Dampling coil（＋）
3.Driving coil（＋） 4.Driving coil（－）
Connect the leads as shown above; refer to the instructions of the lens.
3.2 Power Terminal
3.2.1 DC 12V SST-6420 model
Connect the power supply to the power-input terminal as shown is the
figure right
1.Power for the camera is 12VCD±10％, connector “DC 12V” as positive
and the “G” is common ground.
2.Vψterminal for external Vertical phase input as Line lock
3.Connector’s center as positive and the outside being common ground.
3.2.2 AC 24V/DC 12V SST-6420D model
This terminal accepts both AC 24V and DC 12V non-polarity
3.2.3 AC 85V~265V SST-6420P model
This camera equipped with a universal switching power supply, it can accept
power source input from 85VAC to 265VAC
-3 -

4. DIP SW function
4.1 Flickerless mode
If you use flickerless function, in this mode, the shutter speed is fixed to 1/100
sec for NTSC system and 1/120 sec for PAL system to reduce the flicker of
fluorescent lights. Better for Japan
FLOFF FLON FLOFF FLON
4.2 AE/AI mode
If you use a fixed or manual iris lens, please select the AE mode to control the
exposure with electronic shutter, the range of shutter speed is from 1/60(1/50)
sec to 1/100,000 sec.
If you use an auto iris lens, please set the AI mode, in this mode, the shutter
speed is fixed to 1/60 sec. during NTSC and 1/50 sec. on PAL
AE AI
AE AI
4.3 BLC mode
As you take a picture with strong light behind the subject, the subject only a
slight darker luminance than the overall screen, please set BLC ”on” to perform
through exposure compensation operation by apply the appropriate luminance
intensity to the dark areas.
In normal light condition, please set the DIP SW to BLC “off”.
BLC BLCOFF BLC BLCOFF
4.4 AGC mode
Set the DIP switch to SUPAGC, the gain is up to 34 dB. In normal AGC the
gain is at 28dB
AGC SUPAGC
A
GC SUPAG
C
4.5 ATW mode/AWB mode
4.5.1 ATW mode --Set the DIP SW to ATW position, the color temperature is
monitoring continuous and the white balance is set automatically by internal
microcontroller, the operating color temperature range is from 2500°k to
18000°k.
-4 -

ATW AWB
ATW AWB
4.5.2 AWB mode-- Conventional auto white balance set the DIP SW to AWB
position. In this case, operation is performed at a faster operating speed than
ATW mode.
5. Cautions:
5.1. Never point the camera toward the sun
Do not epose the lens directly to the sun or to strong light as this may damage
the pick-ip device.
5.2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could damage
the camera.
5.3. Requires a proper operating environment
This camera is designed for indoor use. The alloable temperature range for
operation of this camra is between -10ºC ~ 50ºC and the allowable humidity is
85%RH maximum.
5.4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before lens
installation or whenever the lens is changed. Cleaning should be done by
using a chamois, a very find soft cloth, lens tissue or cotton tipped applicator
and ethanol to carefully remove any fingerprint or dust.
5.5. Check the power source voltage
The power source voltage should be within the specified range. (Camera must
meet the specifications).
5.6. Objects and liquid entry
Never push objects of any kind into this camra sa this may touch dangerous
boltage points of short out parts that could result in a fire or electric shock.
Never spill any kind of liquid on the video product.
5.7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may epost you to dangerous voltage or othe rhazards. Refer
all service to qualified servicing personnel.
5.8. Damage requiring service
Unplug thi svideo product from the all outlet and refer service to qualified
servicing personnel under the following conditions:
1) When the power supply cord or plug is damaged.
2) If liquid has been spilled, or objects has fallen into the video product.
3) If the video product has been exposed to rain or water.
4) If the video product has been dropped or the cabinet has been damaged.
5) When the video product exhibits a distince change in performance.
-5 -

5.9. Installation
Installation should confrom to all local codes.
5.10. Power Supply
OKIUSA does not carry any responsibilities for any problem caused by
defective power suuplies or power transformers. Bad power suuplied and
power transformer will also reduce the lifetime of the camera and lower the
image quality. We strongly suggedt our customers to use power supplies and
power transformers in good quality which have UL certified and regulator.
6. Specifications
Model Number SST-6420 SST-6420D SST-6420P
Power Requirements 12V DC 12V DC+ 24V AC 85 ~ 265V AC
Synchronization Internal
Horizontal Resolution 420 TV Lines
Image Device 1/3” SONY Super HAD CCD
Picture Elements PAL: 500 x 582, NTSC: 512 x 492
Scanning System PAL: 625 lines, NTSC: 525 lines, 2:1 interlace
Min. Illumination 0.8 Lux @F1.2
Aperture Correction Horizontal & Vertical 2H enhancer
Signal to Noise Ratio Better than 48 dB
Flicker Less ON/OFF
Auto Gain Control YES
Auto Iris Shutter Auto iris mode: PAL:1/50 sec, NTSC: 1/60 sec.
Auto Electronic Shutter AES: 1/50(60) ~1/100,000 sec.
Auto White Balance 0.8 Lux
BL Compensation Auto detect, Histogram & Central window weighted
Gamma Correction 0.45
Video Output 1Vp-p, 75Ωcomposite, BNC connector
Auto Iris Lens Accept DC/video servo iris lens
Operating Temperature -10°C ~ 50°C (14°F ~ 122°F)
Weight 0.8g
Dimensions 60 x 53 x 110mm (W x H x D)
To prevent electric shock, do not remove screws or covers.
-6 -
There are no user serviceable parts inside. Ask a qualified service person for
servicing.