Sony SA-TS22W User manual

SERVICE MANUAL
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
SURROUND SPEAKER SYSTEM
9-879-098-02
2004H16-1
© 2004.08
Ver 1.1 2004.08
SPECIFICATIONS
SA-TS22W
Surround (L)
Speaker system Two-way Bass reflex
Speaker unit 70 mm dia. cone type,
25 mm dia. balance-dome-
type tweeter
Rated impedance 4 ohms
Dimensions (approx.) 255 ×1112 ×255 mm
(w/h/d)
Mass (approx.) 5.0 kg
General
Surround speaker (L)
Power requirements 220-240 V AC, 50/60 Hz
P120 V AC, 60 Hz ower consumption 36 W (220-240 V AC)
Design and specifications are subject to change
without notice.
• SA-TS22W is speaker system in
DAV-FR10W/SR4W.

2
SA-TS22W
TABLE OF CONTENTS
1. GENERAL ................................................................... 3
2. DIAGRAMS
2-1. Printed Wiring Board – DIATAMP Board (Side A) – ... 5
2-2. Printed Wiring Board – DIATAMP Board (Side B) – ... 6
2-3. Schematic Diagram – DIAT AMP Board (1/3) – ........... 7
2-4. Schematic Diagram – DIAT AMP Board (2/3) – ........... 8
2-5. Schematic Diagram – DIAT AMP Board (3/3) – ........... 9
2-6. Printed Wiring Board – DIAT POWER Board – ............ 10
2-7. Schematic Diagram – DIAT POWER Board –............... 11
2-8. Printed Wiring Board – DIAT BUILT PD Section – ...... 12
2-9. Schematic Diagram – DIAT BUILT PD Section –......... 13
3. EXPLODEDVIEWS
3-1. Base Cover Section.......................................................... 18
3-2. Cabinet, Front Panel Section ........................................... 19
4. ELECTRICAL PARTS LIST .................................. 20
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metaltrim, “metallized” knobs, screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. Acommercial leakage tester, suchas the Simpson229 orRCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operatedAC voltmeter.The“limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2VAC range are suitable. (See
Fig. A)
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 °C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
1.5 k Ω 0.15 µ FAC
voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.

3
SA-TS22W
SECTION 1
GENERAL
Surround speaker (L)
The surround speaker (L) incorporates the IR receiver. It receives the sound from the IR transmitter and
sends it to the surround speaker (R).
Connect the surround speaker (R).
ON
OFF
ONLY FOR
POWER
DIR-R2
Rear side of the surround speaker (L)
IR receiver
This section is extracted
from instruction manual.
SERVICING NOTE
4-246-444-01
After service, as shown in a figure,
a power cord is fixed.
power cord
Label
Ver 1.1

4
SA-TS22W SECTION 2
DIAGRAMS
•Waveforms
– DIAT AMP Board –
4 IC114 4
2 IC102 tf (BCK)
1 IC102 rd (OSCO)
3 IC107 wd (X1)
20.3 ns 4.5 Vp-p
125 ns 3.5 Vp-p
325 ns 2.5 Vp-p
81.3 ns
1 V/DIV, 50 ns/DIV
1 V/DIV, 50 ns/DIV 2 V/DIV, 10 ns/DIV
1 V/DIV, 100 ns/DIV
2.5 Vp-p
Note on Schematic Diagrams:
•All capacitors are in µF unless otherwise noted. (p: pF)
50WV or less are not indicated except for electrolytics and
tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•C: panel designation.
•A: B+ Line.
•Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
∗ : Impossible to measure
•Voltages are taken with aVOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
•Circled numbers refer to waveforms.
•Signal path.
F: AUDIO
•Abbreviation
CND : Canadian model
MX : Mexican model
TW :Taiwan model
Note on PrintedWiring Boards:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
•DIAT AMP board is multi-layer printed board.
However, the patterns of intermediatelayershavenot been
included in diagrams.
•Indication of transistor.
• Note for PrintedWiring Boards and Schematic Diagrams
C
BThese are omitted. E
Q
Caution:
Pattern face side: Partsonthe pattern facesideseenfrom
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
B
These are omitted.
CE
Q
Note:
The components identi-
fied by mark 0or dot-
ted line with mark 0are
critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés
par une marque 0sont cri-
tiques pour la sécurité.
Nelesremplacer que parune
piéce portant le numéro
spécifié.

55
SA-TS22W
SA-TS22W
2-1. PRINTED WIRING BOARD — DIAT AMP BOARD (SIDE A) — :Uses unleaded solder.
CNP102
CNP106
CNP103
C199
C229
C235
EB101
EB102 C214
CN302
C161
C128
C163
L112
C137
C136
C104 C107 C102
L115
C168
L118
C228
L121
C225
C150
C140
C230
C179
C202
C178
Q110
Q106
R171
R222
FB109
C259
C152
C167
R100
R125
R196
C257
R220
C226
C195
R210
R143
C151
L106
C133
L109
L107
C130C119
R108
C114
R165
R136
R126
C115
R105
C157
R103
D115
R178
C162
C160
C185
FB106
C177
FB107
C155
R164
C154
C135
C138
C197
C103
C101
C256
C153 C182
C213
R106
R186
C183
C200
C203
C231
C193
R169
C236
R177
C170
R185
C189
R142
C209
R211
C210
C238
R139
C217
R191
R159
R154
R195
C201
R156
C194
R203 C218
C232
C171
Q109
R153
R254
R157
L104
FB104
FB105
IC108
C109
R158
C258
CN105
CN104
L105
C175
L108
C224
R209
R206
R204
C223
C227
C127
C141
C134
R205 R207
R208
L111
FB108
L110
C187
R200
C219
R201
C237
L122
C220
C172
C176 C173
R194
L116
C205
C206
C196
C198
R188
R197
C215
C188
R179
R166
D105
D106
D107
D104
R138
Q104
Q103
FB103
R312
R313
R314
R263
C204
C149
C212
C216
C192
C184
R256
FB301 C306
CN301
C310
C301
C309
R301
R303R302
L302
L303
E
E
E
E
E
(SIDE A)
DIAT AMP BOARD
1-862-468-
12
(12)
(CHASSIS)
SPEAKER
(CHASSIS)
16
61
DIAT POWER
BOARD
CN904
(Page 10)
C
DIAT POWER
BOARD
CN905
(Page 10)
B
1
3
POWER LED
BOARD
CNP400
(Page 12)
A
13
2
DIAT BUILT
PD BOARD
CN7301
(Page 12)
E
PIN JACK
BOARD
CN303
(Page 12)
F
SPEAKER
JACK
BOARD
CN100
(Page 12)
D
• Semiconductor
Location
Ref. No. Location
D104 E-12
D105 D-12
D106 D-12
D107 C-12
D115 C-10
IC108 C-8
Q103 D-5
Q104 C-5
Q106 D-17
Q109 F-17
Q110 B-5

66
SA-TS22W
SA-TS22W
2-2. PRINTEDWIRING BOARD — DIAT AMP BOARD (SIDE B) — :Uses unleaded solder.
R252
14
5
8
C240
R214
R213
IC102
IC302
C166
R111
C180
Q107
C124
C129
R212
R215
R155
R112
R137
C120
R172
R120
R119
R116
C131
C105
R127
IC101
R102
R104
C111
C110
C108
R218
C142
R117
R101
L103
IC103
R167
FB102
L102
R110
R109
C116
C190
R145
C207
R180
C132
R189
R114
C181
C191
FB101
R199
IC110
R253
R131
R140
C113
C222
C159
C221
C158
Q105
C165
R144
R198
R141
C126
C125
C169
C208 C123
C122
R115
IC113
R113
C174 X101
Q111
X102
IC105
IC112
R160
C233
R259 C253
C234
L101
R261
R262
R257
R258
C156 R121
R122
R128
R129
R124
C145
C146
C147
C148
Q102
C143 R123
D102
D110
Q112
Q108
R118
R163
R162
R161
IC109
R260
R152
R151
R150
C242
R135
R149
R148
R147
R173
R175
R181
R183
R187
R184
R146
IC114
X103
R193 R192
R190
C186
R217
C244 C211
R168
R174
R176
IC107
IC106
IC104
R216
R219
R224
R225
IC111
C243
R309
C300 C312
C302
C303
C305
R315
R304
R306
R307 R308
R305
R310
C304 D302
D301
Q303
Q302
Q301
L301
C308
C308
1
1
1
3
5
4
3
54
17
7
1
13
54
8
14
148
17
43
61
148
16
1
64
49
17
32
3348
13
12
1
54
13
1
18
36
19
1
18
36
19
E
36
25
24
48 37
16
48
33
32 17
49 64
E
E
E
E
E
1-862-468-
12
(12)
(SIDE B)
DIAT AMP BOARD
•Semiconductor Location
Ref. No. Location
D102 B-17
D110 C-17
D301 F-16
D302 E-16
IC101 E-16
IC102 E-13
IC103 D-14
IC104 F-11
IC105 C-17
IC106 C-13
IC107 C-16
IC109 D-12
IC110 E-9
IC111 D-11
Ref. No. Location
IC112 C-9
IC113 B-11
IC114 C-10
IC302 F-14
Q102 B-17
Q105 D-3
Q107 B-6
Q108 F-3
Q111 A-15
Q112 B-15
Q301 F-15
Q302 F-16
Q303 E-16

77
SA-TS22W
SA-TS22W
2-3. SCHEMATIC DIAGRAM — DIAT AMP BOARD (1/3) —
R110
FB102
R119
R118
R120
R313 R314C120
C116 R109
C132
C128
R116
C131
C134 C140 C130C119
FB104
C142
IC104
R117 C138
L104 10µHFB103
R111
FB101
C110
C111
R102
R104
C108
C135 C136
C127
FB109
X101
R108
R106
C114
C115
R105
C109 C107 C141R115
R114
C126C123
R103
C104
C103
R113R112
C122 C125
R101
C102
C101
IC103
R142
R129 C253 R131
R253
R152R171C143
R123
R124
C147
D102
R121
R122 C148
C152
C146
C145
D110
C150 C151 R127
R258
R257
R126R139
C156
R143
R148
R147
R146
R262
R261
R260
R151
R149
R150
R254
C154
C155
C153
C158
C159
C157
R138
R137
R144
R145
R141
FB107
R136
R165
R259
C149
IC106
R135
R256
C137
FB105
C160 C161C163 C162
Q111
Q103
R252
FB106
EB102
C113
R128
R100
R125
Q110
C124 C129
CNP102
CNP103
IC107
X102
Q102
IC101
C133
IC102
C105
R312
R140
Q112 Q104
IC105
1k
1k
1k
1k
2.2k 4.7k0.01
0.1 3.3k
1
47 16V
68
1
110
50V
0.10.1
0.01
TK11225CMCL-G
10k 0.1
220
0.1
0.01
820
3.3k
0.1
L102
10µH
L103
10µH
0.1
L105
10µH47
16V
0.1
12.288MHz
100
100
0.001
0.001
47k
0.1 47
16V
0.1100
100
100p100p
330
47
16V
0.1
100100
100p 100p
10k
10
50V
0.1
TC74VHCT08
AFT(EL)
100
100 0.22 47k
47k
10047k0.1
22k
47k
0.001
MA111-TX
2.2k
10k 0.1
0.1
0.1
0.22
1SS355TE-17
100
10V 0.1 47k
47k
47k
1k100
L107
10µH
L108
10µH
100p
0
100
100
100
100
100
100
100
100
100
10k
10p
100p
100p
100p
100p
100p
100
100
100
100
100
100
1k
1k
0.1
TC74VHCT08
IC108
µPC2933T-E2
AFT(EL)
10k
3.3k
10
50V
0.01 100
16V
100
10V
0.01
DTA114EKA-
T146
DTC114EKA-
T146
10k
0.1
10k
150
150
DTA114EKA-
T146
10p 33p
3P
6P
MB89537APFM
-G-565-BNDE-1
8MHz
2SC1623-T1
-L5L6
XC62HR1502MR
0.1
L106
10µH
CXD4017R
0.01
L104
47µH
4.7k
100
DTA114EKA-
T146
DTC114EKA-
T146
PST3629NR
A1
A2
A3
B1
B2
B3
B4
B5
SCDT
SCSHIFT
SCLATCH
SRDT
SRDT
CSOD
CSOD
DTVALID
DTVALID
BCK
LRCK
DAOUT
SCMODE
SCMODE
XSCEN
XSCEN
D_SCLK
D_SCLK
D_SWDT
D_SWDT
APX
OFF
OFF
CUT
CUT
CONT
CONT
P-MUT
S-MUT
N-MUT
DGND
V-CONT
DGND
AC-CUT
5V
MAIN-OFF
CSOD
SRDT
SWDT
XSCEN
SCLK
SCMODE
VSS
OSCI
VDDE
VSS
OSCO
TEST0
TEST1
TEST2
TEST3
TEST4
TEST5
TEST6
TEST7
SYMCLK
ICLK
VDDE
VSS
VDDI
DTVALID
EMPFS0
EMPFS1
XTST
MST
XSM
SMCK
VDDE
VSS
ADVRH
ADAVS
ADAVD
ADVRL
ADVIN
VDDE
VSS
XRST
DIFM0
DIFM1
DTSEL
PLREF
PLVAR
TESTMD
APVCI
APCPO
APAVD
APAVS
VSS
VDDI
VDDE
VCOR
CHNUM
DIVCODE
APX
EXTCK
VSS
NC
XSCEN
VCC
DIAT_SWDT
DIAT_SRDT
DIAT_SCLK
V_CONT
SI2
INT24
DAMP_SCDT
DAMP_SHIFT
DAMP_LATCH
T_SENSE
MAIN_OFF
P10
SCMODE
DRIVE_OCP
DRIVE_RST
DAMP_NSPMUTE
DAMP_SOFTMUTE
DAMP_PGMUTE
LED_GREEN
LED_RED
DRIVE_OTW
MOD2
AVCC
AVR
DTVALID
AVSS
CSOD
MODEL
SIMUKE
MOD0
MOD1
X0
X1
VSS
P23
FS2_EX
XRST_INIT
ACCUT
P22
/RESET
NC VIN CE
VOUT VSS
GND
CNT
CNP
IN
OUT
GND
RED
GND
GRN
(1/3)
+2.5V REGULATOR
LEVEL SHIFT
+3.3V REGULATOR
G
OI
Q103,104,111,112
LED DRIVE
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
SURROUND AMP
CONTROLLER
AC CUT
RESET SWITCH
LEVEL SHIFT
+1.5V REGULATOR
DAOUT
LRCK
TXOUT
BCK
A/D CONVERTER
RF DEMODULATOR
VOLTAGE
DETECTOR
SW1
IN2 IN1
VDD
SW2IN3
GND OUT
R303
1k
R302
3.3k
R301
47k
R304
1k R306
220
R305
470
C304
0.01
16V
C306
0.01
16V
FB301
0
C312
0.01
16V
C309
0.1
25V
C308 100
16V
C300
0
L301
47uH L303
10uH
C301
0.01
16V C307
100
16V
C310
56p
50V
L302
10uH
R315
0
C302
0.01
16V
Q301
2SC2712G-TE85L Q303
2SC2712G-TE85L
Q302
2SC2712G-TE85L
C303
0.01
16V
C303
0.01
16V
R307
1M
D301
1SS355
TE-17
D302
1SS355TE-17
C305
0.1
25V
R308
1M
R309
47k
R310
10k
CN301
2P
CN302
2P
IC302
NJM2235V(TE2)
SWITCH
Q301-Q303
SELECTOR
E
DIAT BUILT
PD BOARD
CN7301
(Page 13)
3.3
2.5
0
0
3.3
4.8
3.3
3.3
4.8
3.3
0
0
2
0
0
4.8
1234
8765
302
F
PIN JACK
BOARD
CN303
(Page 13)
(Page 13)
(Page 11)
(Page 8)
(Page 9)
• Refer to page 16 for IC Pin Function Description. • See page 14 for IC Block Diagrams. • See page 4 for Waveforms.

88
SA-TS22W
SA-TS22W
2-4. SCHEMATIC DIAGRAM — DIAT AMP BOARD (2/3) — •See page 14 for IC Block Diagrams.
C243 C188
R178
R212 R166
C186
R168
R176
R174
R175 R181 R183
R213 C240
R179
R173
R214 R215 C242R197
C215
R196
R192
R193
C244
R190
C211
R188
C235C199
C238
R203
R225R224R219R218R217R216
C221
C222
R198R189
C208
C207
C231C203
R186
D115
R222
C177 C197
C190
C191
R180R167
C180
C181R164
C201C200
R185 R220
C170
IC110
Q107
R155C166 C168
R263
D105D104
C184
C183 R169C182
C185 C193
C189R177 C194
C192
R159R157
R158
R195 C218 C224R191C210C209
C213
C212 C216
L-CH
R-CH
C217
D107D106
R204
R205
R206
R207
R209
R208
R210
R211
Q105
Q106
Q108
C165
R154
R153 R156
C169
Q109
IC112
C259
CN104
2P
CN105
2P
C258C257C256
0.1 0.01
100
22k 0
0.1
0
0
0
560 560 560
22k 47p
0
560
22k 22k 47p0
0.01
100
0
0
0.1
0
0.1
0
2200
35V
2200
35V
1
0
10k10k10k10k10k10k
0.22
0.22
3.33.3
0.22
0.22
0.0330.033
0
MA8027-H-TX
100
0.033 0.033
0.22
0.22
3.33.3
0.22
0.220
11
0100
1
CXD9774M
2SC1623-T1
-L5L6
100k2.2 47
16V
4.7k
P6SMBJ33A-5P6SMBJ33A-5
1
0.0022 2.70.0022
0.047 0.047
0.00222.7 0.0022
1
100k
L112
10µH
L115
10µH
L118
10µH
L121
10µH
100k
100k
2.7 0.0022 0.00222.70.00220.0022
0.047
11
0.047
P6SMBJ33A-5P6SMBJ33A-5
10k
10k
10k
10k
10k
10k
10k
10k
2SA1602TP-
1EF
2SA1602TP-
1EF
2SA1602TP-
1EF
2.2
100k
100k 100k
2.2
2SA1602TP-
1EF
CXD9774M
0.010.010.010.01
A2
A3
C1
C2
C3
C4
OUTL1
OUTL2
OUTR1
OUTR2
(2/3)
POWER DRIVER
DETECT
PROTECT
POWER DRIVER
Q105,106,108,109
OVER LOAD DETECT
(Page 7)
(Page 9)
D
SPEAKER
JACK
BOARD
CN100
(Page 13)
SPEAKER

99
SA-TS22W
SA-TS22W
2-5. SCHEMATIC DIAGRAM — DIAT AMP BOARD (3/3) — •See page 14 for IC Block Diagrams. • See page 4 forWaveforms.
C176
R172
R184 C198
C195
C202
C187C196
C178
C173
IC111
C233
C230
C206
C205
C204
R187
R194
C220
C219 C237
R200
R201
IC114
C223
C229
C226
IC113
C214
C225
EB101
C234
R199
C232
C228
C227 C236
CNP106
R161
R160
C174
C175
R163
R162
C167
C171
C172
C179
FB108
X103
IC109
0.1
100
0 0.1
0.1
47
16V
0.10.1
L110
10µHL111
10µH
L116
10µH
L109
10µH
L122
1µH
47
16V
0.1
CXD9788AR
0.01
22
25V
0.1
0.1
0.1
0
22
10p
0.001 5p
1M
100
MC74VHC1GU04DFT1
0.01
100
16V
0.1
NJM2870F18(TE2)
100
16V
100
16V
0.01
100k
0.01
100
10V
0.1 0.1
6P
100
100
100p
100p
100
100
0.1
100p
100p
47
16V
49.152MHz
TC74VHCT08
AFT(EL)
B1
B2
B3
B4
B5
C1
C2
C3
C4
SCDT
SCSHIFT
SCLATCH
BCK
LRCK
DAOUT
APX
P-MUT
S-MUT
N-MUT
OUTL1
OUTL2
OUTR1
OUTR2
GND
GND
GND
12V
30V
30V
(3/3)
(CHASSIS)
+1.8V REGULATOR
GND
VOUT
N.B.
VIN
CONT
GND
VDD
STREAM PROCESSOR
LEVEL SHIFT
OSC
(Page 7)
(Page 8)
(Page 11)

1010
SA-TS22W
SA-TS22W
2-6. PRINTEDWIRING BOARD — DIAT POWER BOARD — :Uses unleaded solder.
IC903 IC904
IC905
IC901
EXCEPT MX, TW
O
S901
I
POWER
CONNECT
BOARD
CN904
(Page 12)
G
(Page 5)
(Page 5)
•Semiconductor Location
Ref. No. Location
D901 C-7
D902 B-6
D904 D-7
D905 E-8
D906 E-7
D907 D-7
D908 E-8
D909 D-7
D910 D-5
D911 D-8
D913 D-7
D914 E-7
D915 E-7
Ref. No. Location
D921 C-3
D922 D-3
D933 D-2
D934 C-2
IC901 C-6
IC903 D-3
IC904 D-4
IC905 D-5
Q901 E-8
Q902 E-6
Q903 E-7

1111
SA-TS22W
SA-TS22W
2-7. SCHEMATIC DIAGRAM — DIAT POWER BOARD —
L904
D901
R947
TP901
TP902
TP903
TP904
TP905
TP906
TP908
TP909
IC903
R913
D906
TP911
TP913
TP912
TP910
TP914
TP915 TP916
R907
L903
TH902
FH901 FH902
EB901
EB902
D921
R923
D922
TH901
D902
D903
D915
D905
C931
L901
C901
C904
C909
C915
C932
C936
C938
C941
C935
R936
R948R935
R933
R934
C934
R932R931
C925
C933
R939
CN904
R943R942
R945
R938
CN905
R944
C940
TP907
R946
C937
R940 R941
C942
R921C917
C916
R920
R915
R916
R914
C914
C913
C912
R911
R909
C910
R910
CN903
R902
C902
C903
C905 D911
C906
R917
T901
R919
PC902
C918
C907
C908
R905 R924 R925
R922
R906
R926
R912
C911
PC901
PC903
D910
D904
D909
D907
Q901
D908
Q902
D914
Q903
IC905
IC904
R937
D934
D933
F901
LF901
LF902
R908
D913
IC901
D3SB60F3
0
30V
GND
GND
12V
5V
DGND
AC-CUT
MAIN-OFF
TA7812S
820
1/4W
MTZJ-T-77-
20B
GND
GND
VIN
VOUT
D
S/GND VCC
0
PRF18BC471QB1RB
FML-22S
0
11EQS04
-TA1B
NTH13D8R0LA
SARS03
NO MOUNT
MTZJ-T-77- 33B
MTZJ-T-77-
33B
4700p
0.22
0.22
2.2 50V
47
35V
1000 35V
100
35V
100
16V
470
10V
100 16V
2.2k
390
3.9k
47k
4.7k
0.01 25V
3.3k22k
0.001
250V
0.1
50V
1k
7P
1.5k
1.5k
2.2k
1k
7P
1k
220p
50V
V-CONT
100
0.1
50V
11
0.1 50V
68k0.01
25V
0.01
25V
4.7k
22
22
4.7k
0.0033
50V
22
50V
0.1 50V
1k
1k
470p 50V
100
2P
1M
1/2W
10EDB60TA1B2
1.5k
PC123Y22J00F
10k
1k
1/4W
100p
100V
PC123Y22J00F
PC123Y22J00F
UDZSTE-179.1B
11EQS10-TA1
1SS355-TE-17
1SS355TE-17
2SD1616A-TP-LK
11EQS10-TA1
DTA114EKA-T146 UDZSTE-1710B
DTC144EKA-T146
NJM431UTE2
NJM2374AE(TE2)
390
UDZSTE-1718B
UDZSTE-1710B
14MH 0.7A
UDZSTE-176.2B
STR-W6765N
*5
*5
*4
*6
*9
1/4W
*3
*2
1
*7
1/4W
*10
1/4W *10 1/4W
*12
1/4W
*11
2W
*13
*14
*8
2W
IC901
STR-W6765N : EXCEPT US, CND, MX, TW
STR-W6735N : US, CND, MX, TW
T901
ST-2008 : US, CND, MX, TW
ST-2009 : EXCEPT US, CND, MX, TW

1212
SA-TS22W
SA-TS22W
2-8. PRINTEDWIRING BOARD — DIAT BUILT PD SECTION — :Uses unleaded solder.
IC7302
IC7301
(Page 5)
(Page 5)
(Page 5)
(Page 5)
DIAT POWER
BOARD
CN903
(Page 10)
G
• Semiconductor
Location
Ref. No. Location
D400 B-12
D7301 D-8
D7302 D-8
D7303 D-7
D7304 D-7
IC7301 C-3
IC7302 B-2
Q7301 C-3
Q7302 B-3

1313
SA-TS22W
SA-TS22W
2-9. SCHEMATIC DIAGRAM — DIAT BUILT PD SECTION —
D400
T101
CN400 CN905
CN904 S901
CN303
J301
C22 C12
CN100
L7301
R7302
L7302
R7301
C7319
D7304
D7303
D7302
D7301
C7320
IC7302
C7322
C7301
IC7301
R7304
R7303
L7304
L7303
L7305
C7304
C7303
C7306
C7312
C7308
C7318
L7306
R7312
C7324
R7308
R7307
R7306
R7309
R7310
R7311
R7305
C7310
C7323
CN7301
Q7302
Q7301 TP7302
C7315
C7316
C7314
C7313
C7307
C7309
C7311
C7305
C7321
C7317
TP7301
CNP7302
SPR-54MVWF
TERMINAL BOARD
1P
3P
2P
2P
2P
0.001
50V
0.001
50V
2P
1k
2.2k
0.1
PP508
PP508
PP508
PP508
0.01
TK11225CMCL-G
0.1
0.1
CXA3668N-T4
33k
1.5k
0.0068
47p
0.1
0.0047
47
6.3V
47
6.3V
10k
100
10k
10k
22k
1k
100
10
1k
0.001
0.01
2P
2SC2712G-TE85L
2SA1162G-TE85L RF
0.1
47
6.3V
47
6.3V
0.1
0.0068
0.1
0.01
100p
0.1
10p
DET

1414
SA-TS22W
SA-TS22W
•IC Block Diagrams
– DIAT AMP Board –
IC101 XC62HR1502MR
+
–
3OUTPUT
CONTROL
REFERENCE
VOLTAGE
4
1
2 5
CURRENT
LIMIT
NC
VIN
CE
VSS
VOUT
IC102 CXD4017R
ADVRH 6
VSS 5
VDDE 4
TEST14 3
TEST13 2
TEST12 1
ADAVS 7
ADAVD 8
ADVRL 9
ADVIN 10
VDDEE 11
VSS 12
XRST 13
DIFM0 14
DIFM1 15
TEST15 16
A/D
CONVERTER
BUFFER
RAM
ERROR
CORRECTOR
OUTPUT
INTERFACE
DEMODULATOR
PLREF
17
TEST16
19
APVCI
20
VSS
21
APCPO
22
APAVD
23
APAVS
24
APX
31
EXTCK
32
VSS
25
VDDI
26
VDDE
27
VCOR
28
CHNUM
29
DIVCODE
30
PLVAR
18
PLL CLOCK
SELECTOR
CONTROLLER
CSOD33
SRDT34
SWDT35
XSCEN36
SCLK37
SCMODE38
OSCI40
TEST044
TEST145
TEST246
TEST347
TEST448
OSCO43
VSS39
VDDE
41
VSS
42
CLOCK
GENERATOR
TEST11
64
EMPFS1
63
EMPFS0
62
DTVALID
61
DAOUT
60
LRCK
59
VDDI
58
VSS
57
VDDE
56
BCK
54
TEST10
55
TEST9
53
TEST8
52
TEST7
51
TEST6
50
TEST5
49
IC104 TK11225CMCL-G
1 2 3
6 4
CONT
GND
NP
VIN
5
GND VOUT
CONTROL
CIRCUIT
BANDGAP
REFERENCE
CONSTANT
CURRENT
SOURCE
OVER HEAT &
OVER CURRENT
PROTECT
IC110, 112 CXD9774M
RESET 4
GND 1
GND 3
PWM BP 2
DREG RTN 5
GVDD 6
M3 7
M1 10
M2 11
DVDD 12
DREG 8
DGND 9
DGND 14
GND 16
GND 18
PWM
RECEIVER
TIMING
CONTROL
&
PROTECTION
SD 13
OTW 15
DIGITAL
REGULATOR
PROTECTION
LOGIC
OT
&
UVP
DVDD DREG DREG
DGND
PWM AP 17 PWM
RECEIVER
DVDD DREG
DGND
DREG
GVDD
DREG
GATE
DRIVE
GVDD B35
GVDD B36
BST B33
PVDD B
32
PVDD B
31
OUT B
30
OUT B
29
GND
28
GND
34
GATE
DRIVE
OCH
OCL
TIMING
CONTROL
&
PROTECTION
DREG
GATE
DRIVE
GVDD A
20
GVDD A
19
BST A
22
PVDD A
23
PVDD A
24
OUT A
25
OUT A
26
GND
27
GND
21
GATE
DRIVE
OCH
OCL
GVDD
GVDD
IC113 NJM2870F18 (TE2)
5
VIN
4
VOUT
2
GND
3
NOISE
BYPASS
1
CONTROL
BANDGAP
REFERENCE
THERMAL
PROTECTION

15
SA-TS22W
IC901 STR-W6765N
IC904 NJM2374AE (TE2)
D 1
NC 2
S/GND 3
VCC 4
SS/OLP 5
FB 6
OCP/BD 7
DELAY Q
R
S
+
–
+
–
+
–
Q
S
R
+
–BOTTOM
SELECTOR
COUNTER
OSC
R
Q
S
SOFT START
+
–
OVP
REGULATOR
& ICONST
+
–
BURST
CONTROL
START/STOP
BURST
PROTECTION
LATCH
DRIVE
REGULATOR
OLP
BSD
BD
OCP
FB
CS 1
ES 2
CT 3
IN+5
QS
R
PWM
LOGIC
OSC
GND 4
V+6
VREF
+
–
+
–
+
–
ERROR AMP
PWM
COMPARATOR
SI7
CD8
IPK SENSE
– DIAT POWER Board –

16
SA-TS22W
•IC Pin Function Description
•DIAT AMP BOARD IC107 MB89537APFM-G-565-BNDE1 (SURROUND AMP CONTROLLER)
Pin No. Pin Name I/O Description
1NCONot used
2MOD2 I Setting terminal for the CPU operation mode Fixed at “L” in this set
3, 4 NC O Not used
5MODEL I Setting terminal for the model
6SIMUKE I Setting terminal for the destination
7 to 10 NC O Not used
11 AVCC — Power supply terminal (+3.3V) (for A/D converter)
12 AVR I Reference voltage (+3.3V) input terminal (for A/D converter)
13 AVSS — Ground terminal (for A/D converter)
14 DTVAILD I Data valid flag input from the RF demodulator “L”: invalid, “H”: valid
15 CSOD I Captor start delay signal input from the RF demodulator “H” active
16 NC I Not used
17 AC CUT I AC cut detection signal input terminal “L”: AC cut
18 NC I Not used
Reset signal input terminal “L”: reset
19 RESET I For several hundreds msec. after the power supply rises, “L” is input, then it
changes to “H”
20, 21 MD0, MD1 I CPU operation mode setting signal input terminal
22 X0 I Main system clock input terminal (8 MHz)
23 X1 O Main system clock output terminal (8 MHz)
24 VSS — Ground terminal
25 FS2_EX I Not used
26 XRST_INIT O Reset signal output to the RF demodulator and stream processor “L”: reset
27, 28 NC O Not used
29 P23 I Setting terminal for the CPU operation mode Fixed at “L” in this set
30 P22 I Setting terminal for the CPU operation mode Fixed at “H” in this set
31, 32 NC O Not used
33 DAMP_PGMUTE O PG muting on/off control signal output to the stream processor “L”: muting on
34 DAMP_SOFTMUTE O Soft muting on/off control signal output to the stream processor “L”: muting on
35 DAMP_NSPMUTE O NSP muting on/off control signal output to the stream processor “L”: muting on
36 NC O Not used
37 DRIVE_RST O Reset signal output to the power driver “L”: reset
38 DRIVE_OCP I Shut down state input from the power driver “L”: shut down
39 DRIVE_OTW I Overtemperature warning signal input terminal Not used
40 P10 I Setting terminal for the CPU operation mode Fixed at “H” in this set
41 LED_RED O LED drive signal output of the POWER indicator “H”: LED on
42 LED_GRN O LED drive signal output of the ON LINE indicator “H”: LED on
43 to 47 NC O Not used
48 SCMODE O Control mode selection signal output to the RF demodulator
“L”: pin setting, “H”:serial setting”
49 NC — Not used
50 XSCEN O Serial interface enable signal output to the RF demodulator
51 DIAT_SCLK O Serial interface data clock signal output to the RF demodulator
52 DIAT_SWDT O Serial interface data write signal output to the RF demodulator
53 DIAT_SRDT I Serial interface data read signal input from the RF demodulator
54 NC O Not used
55 T_SENSE O Not used

17
SA-TS22W
Pin No. Pin Name I/O Description
56 VCC — Power supply terminal (+3.3V)
57 MAIN_OFF O Power off control signal output to the power control “H”:power off
58 V_CONT O Voltage control PWM signal output to the shunt regulator
59 DAMP_LATCH O Latch control signal output to the stream processor
60 DAMP_SHIFT O Shift clock signal output to the stream processor
61 DAMP_SCDT O Serial data output to the stream processor
62 SI2 I Serial data input terminal
63 INT24 O Not used
64 NC O Not used

18
SA-TS22W SECTION 3
EXPLODEDVIEWS
NOTE:
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•The mechanical parts with no reference
numberin the explodedviewsare not supplied.
•Abbreviation
AUS:Australian model
CND : Canadian model
E41 : 230 V ACArea in E model
HK : Hong Kong model
KR : Korea model
MX : Mexican model
SP : Singapore model
TW : Taiwan model
Ref. No. Part No. Description Remark
3-1. BASE COVER SECTION
Ref. No. Part No. Description Remark
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
12
1
3
4
not
supplied
not
supplied
not
supplied
Cabinet section
not
supplied
12-048-751-01 SCREW +BVTP 3.5X14 TYPE2
22-067-934-01 SCREW +BV M4X16
32-109-042-01 FRAME (WL), GRILLE
44-218-253-62 SCREW (M2.6), +BTTP

19
SA-TS22W
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
3-2. CABINET, FRONT PANEL SECTION
51
51
51
51
51
53
55
56
57
59
56
56
60
51
51
56
56
56
64
58
S901
62
61
60
51
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
#1
#2
SP1
F901
SP2
not
supplied
b
b
51 2-048-751-01 SCREW +BVTP 3.5X14 TYPE2
53 4-255-204-01 CATCHER, MOLD
55 2-109-041-01 PANEL (WL), FRONT
56 7-685-647-71 SCREW +BVTP 3X10 TYPE2 IT-3
57 A-1067-004-A DIAT BUILT PD BOARD, COMPLETE
58 2-109-031-01 CABINET (WL), SPEAKER
(EXCEPT US, CND, CH)
59 A-1067-003-A DIAT AMP BOARD, COMPLETE
60 7-685-647-71 SCREW +BVTP 3X10 TYPE2 IT-3
61 4-254-954-01 SHEET (DMB), RADIATION
62 A-1068-894-A DIAT POWER BOARD, COMPLETE (MX, TW)
(AEP, UK, EA, HK, SP, KR, AUS, CH, E41)
62 A-1067-416-A DIAT POWER BOARD, COMPLETE (MX, TW)
62 A-1079-747-A DIAT POWER BOARD, COMPLETE (US, CND)
064 1-696-169-31 CORD, POWER (AEP, UK, HK, SP, E41)
064 1-696-847-22 CORD, POWER (AUS)
064 1-751-520-21 CORD, POWER (EA)
064 1-769-079-32 CORD, POWER (KR)
064 1-775-789-91 CORD, POWER (MX)
064 1-783-531-72 CORD, POWER (US, CND)
064 1-827-597-41 CORD, POWER (TW)
#1 7-685-260-14 SCREW +KTP 4X10 TYPE2 NON-SLIT
#2 7-685-645-71 SCREW +BVTP 3X6 TYPE2 IT-3
0F901 1-532-465-32 FUSE 3.15A 250V
(AEP, UK, EA, HK, SP, KR, AUS, CH, E41)
0F901 1-533-453-12 FUSE 5A 125V (US, CND, MX, TW)
S901 1-771-124-21 SWITCH, POWER
SP1 1-825-871-11 SPEAKER (7cm)
SP2 X-2021-617-1 SPEAKER ASSY
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

20
SA-TS22W SECTION 4
ELECTRICAL PARTS LIST
NOTE:
•Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•CAPACITORS
uF: µF
•RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
•COILS
uH: µH
•SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . , uPA. . , µPA. . ,
uPB. . : µPB. . , uPC. . , µPC. . ,
uPD. . : µPD. .
•Abbreviation
AUS:Australian model
CND : Canadian model
CH : Chinese model
E41 : 230 V ACArea in E model
EA : Saudi Arabia model
HK : Hong Kong model
KR : Korea model
MX : Mexican model
SP : Singapore model
TW : Taiwan model
When indicating parts by reference number,
please include the board name.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
DIAT AMP
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
1-862-468-12 DIAT AMP BOARD COMPLETE
************************
< CAPACITOR >
C101 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C102 1-126-964-11 ELECT 10uF 20% 50V
C103 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C104 1-126-947-11 ELECT 47uF 20% 16V
C105 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C107 1-126-947-11 ELECT 47uF 20% 16V
C108 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C109 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C110 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C111 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C113 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C114 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C115 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C116 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C119 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C120 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C122 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C123 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C124 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C125 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C126 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C127 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C128 1-126-947-11 ELECT 47uF 20% 16V
C129 1-162-921-11 CERAMIC CHIP 33PF 5% 50V
C130 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C131 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C132 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C133 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C134 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C135 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C136 1-126-947-11 ELECT 47uF 20% 16V
C137 1-126-964-11 ELECT 10uF 20% 50V
C138 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C140 1-126-964-11 ELECT 10uF 20% 50V
C141 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C142 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C143 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C145 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C146 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C147 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C148 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C149 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C150 1-104-658-91 ELECT 100uF 20% 10V
C151 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C152 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C153 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C154 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C155 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C156 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C157 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C158 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C159 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C160 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C161 1-126-933-11 ELECT 100uF 20% 16V
C162 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C163 1-104-658-91 ELECT 100uF 20% 10V
C165 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C166 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C167 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C168 1-126-947-11 ELECT 47uF 20% 16V
C169 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C170 1-164-346-11 CERAMIC CHIP 1uF 16V
C171 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C172 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C173 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C174 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C175 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C176 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C177 1-115-185-11 CERAMIC CHIP 0.033uF 10% 50V
C178 1-126-947-11 ELECT 47uF 20% 16V
C179 1-126-947-11 ELECT 47uF 20% 16V
C180 1-125-898-91 CERAMIC CHIP 0.22uF 10% 50V
C181 1-125-898-91 CERAMIC CHIP 0.22uF 10% 50V
C182 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C183 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C184 1-136-177-00 FILM 1uF 5% 50V
C185 1-163-035-00 CERAMIC CHIP 0.047uF 50V
C186 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C187 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C188 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V