3
MODEL CDL1100-20 Series CDL1100-40 Series
Section ORIGI- SUPPLE- SUPPLE- ORIGI- SUPPLE- SUPPLE-
NAL MENT-1 MENT-2 NAL MENT-1 MENT-2
List of Technical Service Tools — — 3 — — 3
6 CDM-47/57
6-1 GENERAL 6-1 2 — 6-1 2 —
6-2 Tools and Measuring Instruments 6-3 — — G—6
6-2-1 Tools and Special Tools List 6-3 — — G—6
6-2-1-1 General Tools 6-3 — — G—6
6-2-1-2 Special Tools 6-3 — — G—6
6-2-1-3 Test Disc 6-3 — — G—6
6-2-1-4 Measuring Equipments G2—GG 6
6-2-1-5 Software 6-3 — — G—6
6-2-1-6 Expendable and Chemical Supplies 6-3 — — G—6
6-2-2 Setting Single-Operation of CDM-47/57 Mechanism Block 6-4 — — G—7
6-2-3 System Configuration 6-6 — — G—9
6-2-3-1 Set up PS/VS System 6-6 — — G—9
6-2-3-2 System Configuration 6-6 — — G—9
6-3 Trouble Shooting 6-8 — — G—11
6-3-1 Before Trouble Shooting 6-8 — — G—11
6-3-2 Flowchart for Trouble Shooting 6-8 — — G—11
6-3-3 Procedure of ATP Test 6-9 — — G—12
6-3-3-1 Pre-setting 6-9 — — G—12
6-3-3-2 Test Procedure 6-10 — — G—13
6-3-4 Drive Function Check 6-12 — — G—15
6-3-4-1 Pre-setting for Test Mode Operation 6-12 — — G—15
6-3-4-2 Flowchart 6-13 — — G—16
6-3-4-3 Test Command List 6-16 — — G—19
6-3-4-4 Spindle Motor 6-16 — — G—19
6-3-4-5 Sled Gear Train 6-16 — — G—19
6-3-4-6 2-Axis Actuator 6-16 — — G—19
6-3-4-7 Focusing (Focus Bias) 6-16 — — G—19
6-3-4-8 Laser Power 6-16 — — G—19
6-3-4-9 Chucking Mechanism 6-17 — — G—20
6-3-4-10 Sled Motor 6-17 — — G—20
6-3-4-11 Spindle Motor Drive 6-17 —————
6-3-4-12 E-F Balance 6-18 — — G—21
6-3-4-13 RF Level 6-18 — — G—21
6-3-5 Down Load Program 6-20 — — G—23
7 DIAGRAMS
7-1 Circuit Boards Location 7-1 9 — GG25
7-2 IC Pin Function 7-2 — — 7-2 — 26 to 30
7-3 Block Diagrams 7-21 9 — 7-21 9 31, 32
7-4 Frame Schematic Diagram 7-29 9 — 7-29 9 33
7-5 Printed Wiring Board/Schematic Diagram 7-33 — — 7-33 — 34
Main Section 7-33 10 to 15 — 7-33 10 to 15 —
Power Supply Section 7-40 16 to 20 — 7-40 16 to 20 —
Carrier,Mail Box Section 7-46 21,22 — 7-46 21,22 —
Panel Section 7-52 — — 7-52 — —
CD-ROM Drive Section 7-55 — — G— 34 to 41
Continued next page
List of For Primary Service Contents G: Need not refer
Page No: Added, Refer to on page
—: Not applicable
TABLE OF CONTENTS
EDITION
