Sony LIB-162 User manual

LIB-162
4-662-591-11 (1)
AIT Library
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.

2
INFORMATION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to
operate this equipment.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Caution
The mains plug on this equipment must be used to disconnect mains power.
Please ensure that the socket outlet is installed near the equipment and shall be easily accessible.
Notice
Use the power cord set approved by the appropriate testing organization for the specific countries where this unit is to be
used.
WARNING
Before performing any installation or maintenance procedures, be sure that the library power switch is in the off position
and that the power cord is disconnected from the library.
WARNING
The standalone library weighs around 18 kg. At least 2 people are needed to move or lift the library. Make sure you install
the rack-mount library in the lowest possible location in the rack. For best results, use a rack with extension support legs.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance withthe instructions, maycause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device requires shielded interface cables to comply with FCC emission limits.
Diese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung in folgender/folgenden
Umgebung(en):
·Wohngegenden
·Gewerbegebiete
·Leichtindustriegebiete
(Diese Ausrüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B.)

3
ACHTUNG
Zur Trennung vom Netz ist der Netzsecker aus der Steckdose zu ziehen, welche sich in der Nähe des Gerätes befinden
muß und leicht zugänlich sein soll.

4
HINWEIS
Hinweis: Der höchste Schalldruckpegel beträgt 70 dB(A) order weniger gemäß ISO7779.
Operating environment
Installation Horizontal
Temparature 10 ºC to 35 ºC
Relative Humidity
20 % to 80 % (no condensation)
Ratings
Input Voltage
100 -120/200 - 240 V
Frequecny
50 / 60 Hz
Current
1.4 A / 0.7 A Max
Weight approx. 18 kg

4
Table of Contents
Chapter 1 Introduction
Overview.......................................................................7
Product Features and Functions ...............................8
Front................................................................................8
Rear.................................................................................9
Inside (front) .................................................................10
System Structure.......................................................11
Cartridges...................................................................11
AIT Cartridge................................................................11
Cleaning Cartridge........................................................12
Software .....................................................................12
Precautions................................................................12
Chapter 2 Installation
Overview.....................................................................13
Unpacking ..................................................................13
Checking the Package Contents..............................15
Preparing the Host Computer ..................................15
Installing the AIT library............................................16
Connecting the Power Cable....................................17
Connecting to the Host Computer...........................17
Setting the DIP Switches ..........................................19
Connecting SCSI Peripheral Devices ......................20
Turning the Power On/Off.........................................20
Initial Setup................................................................22
Setting the Date and Time.............................................23
Setting the SCSI ID.......................................................24
Setting the Cartridges....................................................25
Connecting to the Network ...........................................28
Chapter 3 Basic Usage
Overview.....................................................................32
Control Panel .............................................................32
Usage of the Control Panel ...........................................32
Viewing the Status Display...........................................33
Menu Items ...................................................................34
Control Buttons .........................................................37
Warnings ....................................................................38
Errors..........................................................................39
Setting or Changing the Password..........................39
Basic Settings............................................................41

5
Disabling the Life Warning Display.............................41
Setting the Bar Code .....................................................42
Setting the R-MIC Function..........................................42
Adjusting the Brightness of the LCD Panel..................43
Disabling the Buttons on the Front Panel...............44
Assigned Element Addresses..................................45
Handling the Cartridges............................................46
Handling........................................................................46
Storing...........................................................................46
Daily Maintenance .....................................................47
Chapter 4 Operating the AIT Library
Overview.....................................................................48
Using the Cartridges .................................................48
Taking Out the Cartridges.............................................48
Replacing the Cartridges...............................................50
Moving the Cartridges ..................................................53
Viewing Information Related to the AIT Library .....54
Viewing Cartridge Information .................................55
Chapter 5 Operating the AIT Drive
Overview.....................................................................57
Viewing Information Related to the AIT Drive.........57
Cleaning the AIT Drive ..............................................58
Chapter 6 Using the Library Administration Menu
Overview.....................................................................62
Library Administration Menu....................................63
Library Administration Menu....................................63
Menu Items.................................................................65
System Configuration Menu.....................................65
Configuration ................................................................65
Network.........................................................................67
SCSI ID.........................................................................69
Password .......................................................................70
Maintenance Menu ....................................................71
Life Count .....................................................................72
Error Count ...................................................................73
Sensor............................................................................73
History...........................................................................75
Diagnostic .....................................................................76
Firmware Upload ..........................................................77
Information Menu ......................................................79
Information....................................................................80
Inventory.......................................................................80

6
Appendix
If You Forget the Password......................................82
Changing the Air Filter..............................................82
Troubleshooting ........................................................83
Transporting the AIT Library....................................84
Hardware Specifications...........................................85
Hardware.......................................................................85
Memory capacity...........................................................86
Optional Accessories (sold separately) ..................86
SCSI Cable and Terminator Specifications.............86
SCSI Cable....................................................................86
SCSI Cable Length........................................................86
SCSI Specifications...................................................86
About SCSI Components..............................................87
About SCSI Bus............................................................87
Error Code List ..........................................................88
Index ...........................................................................90
Trademarks
• Advanced Intelligent Tape is a trademark of Sony Corporation in this country, other countries, or both.
• Other product names are trademarks or registered trademarks of their respective owners in this country, other countries,
or both.

7
Chapter 1 Introduction
Chapter1
Introduction
Overview
LIB-162 is an AIT (Advanced Intelligent Tape) library with a built-in AIT
drive. Up to 16 cartridge volumes can be set and used. You can set and use up
to 16 cartridges at once. The unit can also be connected to, and used with, a
workstation or server.
Up to 16 cartridge volumes can be set
Up to 16 AIT cartridge volumes can be set. Cartridges can be replaced from the
front panel. Since the AIT library has a built-in bar code reader, bar code labels
can beused to manage cartridges. The following types of cartridges can beused
in this library:
• AIT-3 Cartridge: records up to 3.2 terabytes of data
• AIT-2 Cartridge: records up to 1.6 terabytes of data
• AIT-1 Cartridge: records up to 1.1 terabytes of data
Notes
• Cartridges that can be used vary according to the type of built-in drive.
• The memory capacity mentioned above assumes a data compression ratio of
2:1.
Up to two AIT drives can be installed
Up to two AIT drives can be installed and used. (One AIT drive is preinstalled.)
Since AIT drives are hot-swappable units, they can be added or replaced even
while the power is on. If you want to install an additional AIT drive, please
contact your dealer.
The AIT library can be remotely controlled
A browser can be used to configure individual settings. It can also be used to
view library and maintenance information.
Ultra Wide LVD SCSI compliant
The AIT library is Ultra Wide LVD SCSI compliant.
Suitable for rack mounting
Withthe rack mounting kit, ACY-RK2 (sold separately), the AIT library can be
installed on an EIA_STANDARD 19-inch rack. Rack mounting kits are
available from your dealer.

8
Chapter 1 Introduction
Product Features and Functions
Front
A Front Panel
B Power Indicator LED
This LED light is on when the power is turned on.
C Power Standby Switch (Home Position Switch)
Hold for five seconds or more to move the library's internal mechanism to its
designated position or turn the power on or off.
(When preparing to move the device, turn it off with this switch, then set the
transport lock and transport screw in place on the bottom.)
D Cartridge Dock
Load and exchange cartridges in the cartridge dock. When the cartridge dock is
specified using the control buttons, its shutter opens automatically. The library
does not operate while the cartridge dock shutter is open, so close the shutter
using the control buttons after loading or exchanging cartridges.
E Cartridge Select LED
When loading or exchanging cartridges, the Cartridge Select LED light is on
next to the slot that you select with the control buttons. (There are two slots: an
upper one and a lower one.) Cartridge operations affect the cartridge in the slot
whose LED is lit.
F Liquid Crystal Display
The LCD panel displays information such as the operating status. When in
normal standby state, it displays the status of the AIT library.
G Error LED
This LED light is on when an error occurs.
H Control Buttons
These buttons are used to control operations through the Control Panel Menu.
IVentilationHoles
Please be careful not to block the ventilation holes. If the ventilation holes are
blocked, the AIT library may overheat, resulting in fire or other damage.
CANCELENTERMENU
ERROR
STAND BY
1453267
89

9
Chapter 1 Introduction
Rear
A Power Supply Unit
The power supply unit consists of a fan, a power supply connector, and a power
switch.
BFan
Please be careful not to block the ventilation holes. If the ventilation holes are
blocked, the AIT library may overheat, resulting in fire or other damage.
C Power Supply Connector
Plug the provided power cord into this connector.
D Power Switch
In order to turn on the library power, first press this power switch, then press the
front power standby switch. When this power switch is pressed to turn off the
power, the library power is shut off completely.
EFan
Please be careful not to block the ventilation holes. If the ventilation holes are
blocked, the AIT library may overheat, resulting in fire or other damage.
F SCSI connector 1 7SCSI connector 2 8SCSI connector 3
9SCSI connector 4
For information about connecting the SCSI connectors, refer to “Connecting to
theHost Computer”(page17)and“ConnectingSCSIPeripheralDevices”(page
20) in Chapter 2, “Installation”.
J Maintenance Connector
Used for maintenance purposes. Do not use.
K LAN Connector
Connect a 10Base-T network cable here.
L Transport Lock
During installation, set the transport lock here after removing it from the bottom.
M Transport Screw
During installation, set the transport screw here after removing it from the
bottom.
N DIP Switches for Setup
1 2 3 4 5 6 8 qa07 9
q
f
q
d
qs

10
Chapter 1 Introduction
The default factory setting of the DIP switches is as follows.
Use the DIP switches as is.
1: On
SCSI TERM POWER 1 (for SCSI connector 1 and SCSI connector 2 series)
2: On
SCSI TERM POWER 2 (for SCSI connector 3 and SCSI connector 4 series)
3: Not used
4: Not used
Inside (front)
A Cartridge Case (Library)
Up to 16 cartridges volumes can be set.
BAITDrive1(R)
This drive is a standard built-in drive.
C Additional AIT drive slot (AIT Drive 2 (L))
Attach an additional AIT drive. Add a product of the same format as AIT Drive
1 (R).
1
2
3

11
Chapter 1 Introduction
System Structure
Generally, the library is connected to the host computer and used to control the
library from the host computer. Also, you can connect the library to the network
so that it can be configured and maintained through a browser.
Notes
• A SCSI host adapter card must be installed in the host computer.
• In order to configure and maintain the library through a browser, browser
software must be installed in the computer. Operating systems and browsers
that are compatible with this library are as follows.
Operating systems:
- Microsoft Windows 95, Microsoft Windows 98, Microsoft Windows Me,
and Microsoft Windows 2000
Browsers:
- Microsoft Internet Explorer 5.01 or later
- Netscape Communicator 4.7 or later
Cartridges
This section describes used in the AIT library.
AIT Cartridge
AIT cartridges for AIT-3, AIT-2 and AIT-1 drives can be used in the AIT
library. To achieve the maximum transfer rate and recording capacity, use the
optimum cartridges for the type of AIT drive installed. For information on
recording capacities, refer to “Hardware Specifications” (page 85) in the
“Appendix” chapter.
Ethernet
Wide SCSI LIB-162
Control the
library.
Make library settings and
perform maintenance.
Host computer

12
Chapter 1 Introduction
AIT-1 Drive
AIT-2 Drive
AIT-3 Drive
Caution
Do not use 8 mm video tapes sold at stores. An 8 mm video tape looks a lot like
an AIT cartridge, but has different specifications. Do not use any other
cartridges other than AIT cartridges.
Cleaning Cartridge
To clean the AIT drive, use an AIT cleaning cartridge. For information on
cleaning, refer to “Cleaning the AIT Drive” (page 58) in Chapter 5, “Operating
the AIT Drive”.
Software
For guidance on application software that can be used with the AIT library and
supported operating systems, contact your dealer.
Precautions
• Up to two AIT drives can be set and used in the AIT library. If you want to
use two AIT drives, use products with the same format. Using products with
different formats may result in improper operation.
• In the cartridge slots, use the optimum cartridges for the type of AIT drive
installed. Using cartridges other than an AIT cartridge may cause improper
operations. For information about cartridges that can be used with the AIT
library, refer to “Cartridges” (page 11).
• Do not insert anything except AIT cartridges in the cartridge dock, as doing
so may result in damage.
AIT-1 mark
AIT-2 markAIT-1 mark
AIT-2 markAIT-1 mark AIT-3 mark

13
Chapter 2 Installation
Chapter2
Installation
Overview
This chapter explains general procedures for positioning the AIT library,
connecting itto the host computer and turningon the library power. Thischapter
also explains initial set-up. Installation and set-up steps may vary depending on
your system.
After turning on the power, make settings required to use the unit as explained
in “Initial Setup” (page 22).
Unpacking
Note
You will need the box, packing materials, transport lock and transport screw if
you wish to move or transport the AIT library in the future. Retain them for
future use.
1
Remove the AIT library from the box as indicated on the box.
Remove the packing materials, such as plastic covers and tapes.

14
Chapter 2 Installation
2
Place the library standing up so that the bottom is visible.
3
Remove the transport lock (1) and transport screw (2). To cover the holes,
affix the silver stickers provided on the positions marked by dotted lines in
the illustration below.
The transport lock (1) can be removed by turning it 90 degrees to the left
or right.
Remove the transport screw (2) by turning it counterclockwise.
• When you remove the transport lock and transport screw, cover the holes
with the silver stickers provided.
4
Attach the transport lock (1) and the transport screw (2) to the rear of the
library.
Bottom
(1)*
(2)*
90˚90˚
(2)
(1)

15
Chapter 2 Installation
Checking the Package Contents
After opening the package, make sure that all of the following items are present.
Contact your dealer if anything is missing.
• LIB-162 main unit (1)
• Power cable (1)
• SCSI terminator (1)
• Quick Start Guide (1)
• CD-ROM (this manual) (1)
• Bar code label (1 sheet)
• Transport Lock (1)
• Transport Screw (1)
• Transport lock/screw sticker (silver) (2)
• Safety Notice (1)
Note
In addition to the above, other documentation and papers may also be included
in the package.
Preparing the Host Computer
To prepare the host computer before installing the AIT library:
1
Make sure that a SCSI host adapter card is installed in the host computer.
2
Install the application software supporting the libraryon the hostcomputer.
For guidance on application software that can be used with the AIT library
and supported operating systems, contact your dealer.

16
Chapter 2 Installation
Installing the AIT library
The library weighs about 18 kg (39.7 lb.) and has the following dimensions.
Before installing the library,make sure that the surface on which you are placing
it is large and strong enough.
Withthe rack mounting kit, ACY-RK2 (sold separately), the AIT library can be
installed on an EIA_STANDARD 19-inch rack. Contact your dealer for
information about the rack mounting kit.
Note
Install the AIT library on a horizontal surface near an AC power outlet. Also,
leave a gap of about 150mm (5.9 in.) behind the rear of the unit to allow air to
circulate.
ERROR
CANCEL
ENTER
MENU
STANDBY
680mm (26.8 in.)
430mm (16.9 in.)
88mm (2U)
F
ront 430mm (16.9 in.)
680mm (26.8 in.)
Rear
150mm
(5.9 in.)

17
Chapter 2 Installation
Connecting the Power Cable
1
Confirm that the power switch on the rear of the AIT library is turned off
(a is pressed).
2
Connect one end of the power cable to the power supply connector and the
other end to the electric outlet.
Connecting to the Host Computer
Connect the AIT library and the host computer with a SCSI cable. This section
explains general connecting steps. To connect, use the Ultra Wide SCSI cable
sold at stores. The library side uses the 68-pin half pitch connector.
When connecting other SCSI devices together with the AIT Library, see
“Connecting SCSI Peripheral Devices” (page 20).
Caution
• Do not connect the AIT library to the High Voltage Differential (HVD) SCSI
bus. If connected, the library or other devices on the SCSI bus may be
damaged.
• When connecting the Wide SCSI cable, turn off allof the connecting devices,
including the host computer.
• When connecting the AIT library as the last device on the SCSI bus, be sure
to attach the provided terminator. Also, if the host computer is equipped with
a single-end SCSI host adapter, use a terminator that supports single-end.
When the wrong terminator is used, the device may be damaged.
• In Ultra Wide SCSI, make the length of the LVD (Low Voltage Differential)
SCSI cable, which connects the host computer and the device at the end of the

18
Chapter 2 Installation
SCSI bus, shorter than 12 meters (39 ft. 4.4 in). (When connecting the AIT
library to a single-ended SCSI host adapter that provides SCSI termination,
use a SCSI cable shorter than 1.5 meters or 59 inches.)
• Using SCSI cables longer than 30cm (11.8 in.) to connect between devices is
recommended.
• SCSI cables cannot be branched.
Notes
• For information about the SCSI bus, refer to “SCSI Specifications” (page 86)
in the “Appendix” chapter.
• Prepare the necessary SCSI cables. For information about SCSI cable
specifications, refer to “SCSI Cable and Terminator Specifications” (page 86)
in the “Appendix” chapter.
1
Confirm that the power to the hostcomputer and AIT library are turned off.
2
Attach the SCSI cable and terminator as shown in the figure below.
The manner in which it is attached varies with the number of internal
drives.
When there is only one standard internal AIT drive (AIT drive is
not added):
1Use a SCSI cable (sold at stores) to connect the AIT library to the host
computer.
2Connect the SCSI cable to connector 1.
3Attach the provided terminator to connector 2.
Nothing is connected to connector 3 and connector 4.
When an AIT drive is added (there are two installed AIT drives):
1Use a SCSI cable (sold at stores) to connect the AIT library to the host
computer.
2Connect the SCSI cable to connector 1.
3Connect a SCSI jumper cable (sold at stores) from connector 3 to
connector 4.
2
1
Host computer
Terminator

19
Chapter 2 Installation
4Attach the provided terminator to connector 4.
Setting the DIP Switches
DIP switch settings determine whether electric power is supplied to the SCSI
terminator (when multiple SCSI devices are connected).
The default factory setting of the DIP switches is as follows.
1: On
SCSI TERM POWER 1 (for SCSI connector 1 and SCSI connector 2 series)
2: On
SCSI TERM POWER 2 (for SCSI connector 3 and SCSI connector 4 series)
3: Not used
4: Not used
2
3
1
Host computer
Terminator