Soozier A90-326V80 User manual

INapb007_US
A90-326V80
TREADMILL
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
UESR’S MANUAL

1. CAUTION
To avoid any hurts, please read this manual carefully before using.
For safety purpose do not stand on running belt while start.
Please stop immediately for any feeling of vomit、jerky during using.
Please increase speed slowly if needed.
Adjustment of belt is prohibited during using.
It is suggested to wear sports shoes when using the machine.
Children、elder、pregnant women、patients are prohibited to use the machine.
2. SAFETY NOTIICE
Please put the machine on flat ground. It is unsuitable to put the machine at following places:
1 Outdoors.(The machine is specially designed for indoor use only)
2
Slant ground or slant places on balcony.
3 Sunlight area or near heater.
4
Big noisy places.
Error may be appeared if the power is not stable. Please do not use the same socket
together with computer、air conditioner etc.
It is suggested to wear sports shoes and gym suit when use the machine.
Please increase or decrease speed slowly.
Do not put the machine near to wet object. Error maybe caused by water drop.
3. CAUTION DURING USE
If you do not feel well before using, please consult with your doctor or coach.
It is not our company’s responsibility for any improper use by user to cause body injured.
Please pull up plug after using.
Please pull out plug for any movement or change parts for the machine.
Children 、elder and pregnant women are prohibited to use the machine. Patients need
doctor’s consultant before using.
Please place the machine on flat places. Do not locate any objects 2M behind the machine.
Do not start the machine when it is folded.
Water drop is prohibited to run into the machine , especially to motor, power line andplug.
Danger may cause if wearing long dress or other unsuitable dresses during use.
Encloser spaces, air uncirculated places and with flammability places are prohibited to use

the machine.
Do not put any objects on the machine.
Put away the plug from heated place or fire seat.
Please switch off all functions and pull out plug after using.
Please do not stand directly on the belt while starting the machine.
Do not disassemble the machine without conduct of professional person.
Please make sure the running belt is fastened before using.
4. Technical Specification
Product Name
Treadmill
Item No.
A90-326
Power
0.75HP
Voltage
100-110V
Frequency
50Hz
Speed
1-6km/h
User Capacity
100KG
5. Control Panel
(1) Display
1.1 “TIME” window has two modes which shows the running time.①Forward
counting time is from 0:00 to 99:59 minutes. ②Countdown is count to 0 from the
set time(setting range: 5:00~99:00 minutes). The machine will stop slowly when it
counts to 0:00 and shows” end”, then the machine will come to the standby mode
after 5 seconds.
“STEP ”window shows the steps. It counts from 0 to 9999 steps. It will recount
when the step numbers reaches the top point.
Note:The window will be switched from TIME and STEP cyclically, you can
press“ M” button to switch between cyclic display mode and single display
mode in motion state.

1.2 “DISTANCE”window has two modes which shows the current movement
distance. ①In the forward counting mode, the distance will be increased from 0.0
to 99.9 miles, it will recount if the distance reaches the top point. ②In the distance
countdown mode, the distance will be decreased from the setting data(setting
range:1.00~99.00miles) to 0 . The machine will stop slowly when it counts to 0:00
and shows” end”, then the machine will come to the standby mode after 5
seconds.
“CALORIES”window has two modes which shows the calories.①Forward mode
counts from 0 to 9999, it will recount when it reaches the top point. ②countdown
mode will count from setting calorie data( setting ranges 20~990) to 0. The
machine will stop slowly when it counts to 0:00 and shows” end”, then the
machine will come to the standby mode after 5 seconds.
Note: The window will be switched from DISTANCE and CALORIES
cyclically, you can press“ M” button to switch between cyclic display mode
and single display mode in motion state.
1.3 “SPEED” window shows the current running speed, the setting range is
0.5MPH~6.0MPH. The speed will +/- 0.1MPH every time you click “+/-” button.
P1 ~ P12 are displayed under the setting of automatic selection.
1.4 After the treadmill is started, every window will be displayed cyclically at an
interval of 5 seconds. You can press the "M" button to switch between cyclic
display mode and single display mode.
(2) Function Of The Remote Control
2.1 “Start/Stop”:
(1) In standby or countdown mode: Pressing “start/stop” button to start the machine.
Note: The default speed is 0.5MPH/H.
(2) Choose the preset program: Pressing “start/stop” to start the machine and the
speed will changes according to the preset speed.

(3) In running state: Pressing “start/stop” , then the treadmill will stop slowly and
back to standby state.
2.2 “+”“-”button is to adjust speed. Keep pressing “+”/“-” over 0.5 seconds, the speed
will keep increasing or decreasing. Note: The speed will change by 0.1mph.
2.3 “M”:①In standby mode: it can switch from different mode, including Time,
Distance and Calories. ②In running mode: press ”M” button will switch display
mode between cyclic display mode and single display mode.
2.4 “P”: There are P01~P12, totally 12 preset programs you can choose in standby
mode.
2.5 Press the “ ” once to mute the machine, and press it again to resume the
beep sound.
2.6 After use, press " " button, treadmill will stop slowly and it will retain its
data until power off.It will resume the previous speed when start again.
"Reset": Press the " " button, the data will reset. It only works when
treadmill is in standby mode.
(3) Functional Instruction
3.1 Sports mode: Press “start” key to start the machine and the SPEED window will
count from“3 2 1 ”. Please note that the default speed is 0.5MPH and you can
press“+”“-” to adjust speed.
3.2 Countdown mode: when in standby, press“M” key to choose countdown for time,
distance and calories. Press “+”“-” to set relevant data. After setting, press“start/stop”
to start the treadmill, it will count down from the set data, the machine will stop by
itself when it counts to 0.
3.3 Preset program(P01~P12): choose one program first and then press “+”“-” to set the
running time(ranges 5:00~99:00, and the default time is 30:00), press “start/stop” to
start the machine, it will run according to the preset speed and speed will change
according to the time ”(Time/20)”.

(4) About the Remote Control
4.1 Pull out the insulating sheet, you can use the remote control directly.
4.2 The remote control can directly control the treadmill.
4.3 If you have purchased multiple treadmills, in order to prevent the treadmills from
interfering with each other, please perform the following operations to match.
4.3.1 Turn on the treadmill.
4.3.2 Simultaneously press the left and right buttons on the remote control for 5 seconds.
The display will flash, and the treadmill and the remote control will be paired.
4.3.3 Please note: After matching the remote control, if the remote control isreplaced,
please perform the matching again according to the above operation.
6. Bluetooth Speaker Instructions
Turn on the Bluetooth switch in the phone settings, find the available Bluetooth devices in the
Bluetooth device connection selection, then select and connect the available Bluetooth audio
devices.
7. USAGE OF SILICONE OIL
Pull up tightly of the running belt. Then put the silicone oil to
running board. Then start the machine to running 3 minutes
without loading. It is better to maintain like this every 30 hours
working of the machine. This can save lifetime of parts properly.

8. Runbelt Adjustment
(1) Running belt deviate to left
Start the machine by speed at 2-3mph/h without loading, use die nut to make the screw go
1/4 circle(see fig1). Then make the machine running without loading 1-2 minutes. Please adjust
like this to make the belt till to mid place.
(2) Running belt deviate to right
Start the machine by speed at 2-3mph/h without loading, use die nut to make the screw go
1/4 circle(see fig2). Then make the machine running without loading 1-2 minutes. Please adjust
like this to make the belt till to mid place.
(3) Running belt logjam
If the running belt is in dead condition, use die nut to make the screw 1/2 circle both left and
right till this logjam solved.
9. DAILY MAINTAINANCE
1. Please disconnect power before checking the machine or cleaning.
2. Clear belt and dial plate after use, at least once a week.
3. Check and tighten screws and spines at fixing point.
4. Do not hang clothes or other objects on the machine.

10. Trouble Shooting
Error
Code
Meaning Problem Solution
E2 Control Board Error
Control board is broken
or pseudo soldering on
control board
Replace control board
E4 Control Board Error Control board is broken Replace control board
E5 Over
current Protection
Control board short
circuit or motor blocked
1. Open the motor cover and check
whether the motor is blocked. Remove
the block if yes.
2. Replace the control board if it’s not
blocked, or the error still shows.
E6 Motor Error Motor broken or motor
line fall off
1. Open the motor cover and check
whether the motor is broken or whether
the motor wire is connected to control
board properly. Reconnect the wire is
recommended.
2. Replace the control board if the error
still shows.
E7 Communication
Failures
Wires from the control
board to panel board are
broken or not properly
connected
1. Make sure the wires from the control
board and panel board are connected
securely and not damaged.
2. Replace the control board if the error
still shows.
E8 Overload Protection
Excess of electricity or
user exceeded max load
weight
1. Make sure the user does not exceed
max weight capacity.
2. Reconnect power and re-start the
machine.
3. Replace the control board if the error
code still shows.