Soundcore Motion X600 User manual

USER MANUAL
soundcore Motion X600

English 01
Čeština 11
Dansk 21
Deutsch 31
Español 41
Suomi 51
Français 61
Italiano 71
Nederlands 81
Norsk 91
Język polski 101
Portugues do Brasil 111
Pусский 121
Svenska 131
Türk 141
日本語 151
한국어 161
简体中文 171
繁體中文 181
ةيِبَرَعل 191
תי ִ רבִע201

01 EN
At a Glance
1. Power
2. Bluetooth
3. Spatial Sound
4. BassUp
5. Volume Down
6. Play / Pause
7. Volume Up
8. USB-C Charging Input
9. AUX IN

02 EN
Charging
Use a certified USB-C cable and charger to prevent any damage.
Fully charge this speaker before the first use to prolong the lifespan of the built-in
battery.
Flashing red Low battery
Steady red Charging
Steady white Fully charged

03 EN
Powering On / Off
Press once Power on
Steady white
Press and hold for at least 2 seconds Power off
Light off
This speaker will power off automatically after 20 minutes if no device is connected.

04 EN
Using Your Speaker
Bluetooth Mode
With this speaker, you can enjoy music through your Bluetooth-enabled devices.
Press once Enter Bluetooth pairing mode
Flashing blue Bluetooth pairing
Steady blue Bluetooth connected
• To re-enter Bluetooth pairing mode, press the Bluetooth button once.
• This speaker can only play music on one mobile device at a time. To play from
another connected device, pause the device that's currently active first.
• Each time you power on your speaker, it will automatically connect to your
last connected device if available within the Bluetooth range. If not, press the
Bluetooth button to enter Bluetooth pairing mode.

05 EN
TWS (True Wireless Stereo) Mode
Two identical Motion X600 speakers can pair with each other for stereo sound.
Both speakers can play the same audio (one as the left channel and the other as
the right channel).
1. Connect either speaker with your Bluetooth device.
2. On both speakers, press and hold the Bluetooth button for at least 2 seconds
to enter TWS pairing mode.
Press and hold for at least 2 seconds Enter TWS pairing mode
Flashing white TWS pairing
Steady blue (Speaker 1) TWS connected
Steady white (Speaker 2)
To exit TWS mode, press and hold the Bluetooth button for at least 2 seconds.

06 EN
Spatial Sound
Spatial sound places sound all around you to create an immersive listening
experience.
x1 OFF
ON
Press once Turn spatial sound on / off
Steady white Spatial sound on
Light off Spatial sound off
LDAC
Use devices powered by Android 8.0 or later to experience LDAC quality sound.
1. Open the soundcore app.
2. Go to the Settings icon on the home page.
3. Click on "Sound Mode."
4. Select "Preferred audio quality" to switch to LDAC codec.

07 EN
1
2
3
4
• It takes about 10 seconds to switch audio codecs. You may be requested to
update the speaker's firmware if available.
• LDAC provides higher quality sound, increases power consumption, and
reduces playtime.
• Enable LDAC in a low-interference environment to ensure a stable Bluetooth
connection.
AUX Mode
Insert a 3.5mm AUX cable (not included) to play audio on an external device.
When using AUX mode, control audio playback via the connected device.

08 EN
Button Controls
Press once Power on
Press and hold for at least 2
seconds Power off
Press once Enter Bluetooth pairing mode
Press and hold for at least 2
seconds Enter / exit TWS pairing mode
Press once Turn spatial sound on / off
Press once Turn BassUp on / off
Press Volume up / down
Press once Play / pause
Press twice Next track
Press three times Previous track
Press once Answer / end a call
Press and hold for at least 2
seconds Reject a call
Press and hold for at least 2
seconds Activate voice assistant software
Reset
Press and hold the Bluetooth button and volume up button simultaneously for at
least 4 seconds to reset the speaker.
4