Soundigital 3000.1D User manual

3000.1D

1 Promotional Sticker
1 3000.1D NANO Amplifier
1 Owner’s Manual
PACKAGE CONTENTS

INTRODUCTION
We recommended the use of SounDigital original
accessories for better performance. The crossovers,
power supplies and voltmeters offered by SounDigital
follow the same quality standards as our amplifiers,
assuring an excellent quality and high-power sound
system to our customers.
Dear Customer,
Congratulations on acquiring your SounDigital!
You've just purchased a product of high quality and
technology. The SounDigital products are developed to
assure maximum efficiency and reliability to your
sound system.
Read this manual and follow its instructions and
information carefully. It contains extremely important
information to have your amplifier working properly. If
you feel the need to contact our Tech Support, you can
r e a ch o u r t ec h n ic i a ns t h r ou g h t h e e -m a il
[email protected].
IMPORTANT INFO
To know our complete line of amplifiers and
accessories, visit www.soundigitalusa.com.
This “Warning” sign alerts the user of
important info. Not following these
instructions may cause injuries to the
user or damage to the equipment.
Warning!
ØInstall the amplifier in an vented location and avoid
obstructing the side ventilation windows;
ØBe careful when making holes in the vehicle. Make
sure you're not making holes in the fuel tank, brake
lines or electrical cables of the vehicle;
ØWear gloves, safety glasses and all necessary PPE
during the installation of SounDigital amplifiers;
ØDo not install the amplifier in places exposed to
water, dirt or humidity;
ØTo prevent personal injuries or damage to the
amplifier, read all the safety instructions written on this
manual.
ØUse rubber O-rings when passing wires to metal
walls to prevent them from being cut off and short-
circuiting;
ØThis equipment is for use in automotive DC voltage
batteries, between 12.6 and 14.4 volts. Before
installing the equipment, check the voltage of the
batteries;
ØIf you have questions about the installation of this
equipment, get in touch with our tech support or with a
professional specialized in car audio installation;
ØMake sure the cables are properly fixed throughout
the installation;
ØSecure the amplifier properly and firmly. Avoid fixing
to metal parts, as this may cause ground "looping"
(noise);
SECURITY INSTRUCTIONS
ØBefore proceeding with the installation of any
electric equipment on your vehicle, unplug the negative
(-) terminal of the battery to avoid fires, injuries or
damages;
ØUse your sound system safely, exposure to
continuous sound pressure over 85 dB may cause
irreversible hearing loss.
ØMake sure that the location chosen for installation
of the amplifier does not impair the operation of the
vehicle;
1

DESCRIPTION PANELS
Audio input RCA connector;
Audio output RCA connector;
Variable high pass filter control (5Hz ~ 80Hz);
Variable low pass filter control (80Hz ~ 25kHz);
Variable signal gain control;
Variable bass boost control (0dB ~ +12dB);
Negative power supply connector (GND);
Positive power supply connector (+12V);
Remote power supply connector (REM);
Cooler fan;
“Protection” LED indicator (Red);
“Clip” LED indicator (Yellow);
“Power On” LED indicator (Blue);
Negative speaker connector (-);
Positive audio output connector (+);
Minimum output impedance;
21 312
98
74 5 6 10 11
14 15 1613
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2

INSTALLATION
The max. distance for the installation of
the fuse/circuit breaker is one foot away
from the battery.
Warning!
ØMake all of the connections to the busbars fuse
holders or circuit breakers, with no fuses in the holder
and with the circuit breakers in the "Off" position;
ØAffix the amplifier in such a way you have access to
the connectors;
ØInstall the power cables on the vehicle in a proper
way. From the battery to the busbar, fuse holder or
circuit breaker. Chose the appropriate section for the
cable.
INSTALATION SEQUENCE
ØBefore proceeding with the installation, unplug the
negative from all of the batteries;
ØConnect the RCA cables to the head unit and
amplifiers;
ØConnect the power cables in to the amplifier,
observing the polarity. Connect all the positive cables
from the fuse holder or circuit breaker to the positive
conector of the amplifier and all the negative power
cables from the busbar or from the batteries, to the
negative connector of the amplifier;
ØInstall the signal input cables in a proper way,
distant from the power cables;
ØInstall the audio output cables with the appropriate
section , distant from the power and audio input cables;
ØInstall the remote cable with the power cables,
using a section of 1.5mm² or thicker;
ØConnect the remote cable to the REM terminals on
the amplifier and to a 12V power supply activated by a
switch key or to the remote power output of the head
unit;
ØBefore powering the system, verify all the
connections and make sure there are no mistakes or
short-circuits on the power and ground cables;
ØReconnect the ground of the batteries;
ØCheck if the remote key is in the "Off" position and if
the head unit is turned off, then place the fuses in the
fuse holders or switch the circuit breakers on.
ØTurn the gain control all the way down;
Para a correta regulagem do ganho do seu
amplificador, siga os seguintes passos:
PROCEDURES FOR SETTING THE GAIN
ØDisconnect the output cables from the amplifier
outputs;
ØTurn off all processing (bass, treble, loudness, EQ,
etc.). Set the source unit's fader control to center
position. Set the source unit volume to 3/4 of full
volume;
ØAdjust the audio controls of the audio in the center
(fader left and right controls);
ØReproduce a 60Hz sine wave signal through the
head;
ØTurn up the gain clockwise slowly until the "CLIP"
LED starts blinking;
ØSome head units with higher tension RCA
outputs, may reach max power even with the gain set
close to minimum. In such cases, limit the volume of the
head unit in such a way the "CLIP" LED will not blink.
3

0dB
-12dB
dB
Hz
ØExample of one RCA cable connection only and
using the RCA output to connect another amplifier.
ØExample of two RCA cables connection.
INPUT CONNECTIONS
ØExample of one RCA cable connection only.
Hz
050Hz
12dB
dB
0dB
3dB
9dB
6dB
BASS BOOST LEVEL
Bass Boost Chart
High
Pass
High
Pass
-3dB
c/2
ƒc ƒ
A
0dB
-15dB
Hz
dB
CROSSOVER ADJUSTMENT
Ø'Full Range'' Use – (all frequencies playback) - For
all frequencies playback, the ''HIGH'' variable control
shall be set to 5Hz, and the ''LOW'' variable control to
20kHz;
ØUse in ''High Pass'' cut filter (HIGH) 12dB/oct – Set
in the ''LOW'' variable control to 16kHz and in the
''HIGH'' variable control, set ''A'' frequency between
5Hz and 80Hz, where you want to perform the high
pass cut filter;
ØUse in ''Low Pass'' cut filter (LOW) 12dB/oct – Set in
the''HIGH'' variable control to 5Hz and in the ''LOW''
variable control, set ''B'' frequency between 80Hz and
20kHz, where you want to perform the low pass cut
filter;
ØUse in ''Band Pass'' cut filter – Set in the ''HIGH''
varia-ble control the ''A'' frequency between 5Hz and
80Hz, where you want to perform the high pass cut
filter and set the ''LOW'' variable control to ''B''
frequency between 80Hz and 20kHz, where you want
to perform low pass cut filter;
-3dB
0dB
-15dB
Low
Pass
B
c
ƒc*2 ƒ
Low
Pass
Hz
dB
-3dB
c/2
ƒ
High
Pass
c
ƒ
High
Pass
0dB
-15dB
Low
Pass
c
ƒc*2 ƒ
Low
Pass
Hz
dB B
A
INSTALLATION
USING BASS BOOST
ØSet boost intensity between 0dB and +12dB at the
variable control BASS BOOST.
Cuidado!
You should never connect or disconnect
RCA cables with the amplifier turned on,
because it may damage the head unit or
the amplifier.
4

Unplug the negative (-) terminal of the battery before proceeding with any electrical
installation in the vehicle to avoid fire starts, wounds or damage to the amplifier.
Cuidado!
POWER INPUT WIRING
WIRING CONNECTIONS
REMOTE
+12V
GND
FUSE
FUSE
OUTPUT WIRING
GND
+12V
GND
5

TECHNICAL SPECS
*Power at 14.4V @ 60Hz following the ANSI / CTA-2006B standard with a maximum THD of 1%
PARAMETER
RMS Power @ 4Ω*
RMS Power @ 2Ω*
RMS Power @ 1Ω*
Frequency response (-3db)
Power Supply Voltage
SNR
Input Sensibility
Current draw (music)
Max. Current draw (resistive load 1kHz @ 12,6V)
Total efficiency (full power @12,6V)
Damping factor
Gross weight
Giftbox dimensions (LxWxH)
Size of recommended cable (power)
Size of recommended cable (output)
Fuse/Circuit breaker (music)
Recommended capacity of the battery
Low Pass Filter
3000.1D NAN0 1Ω
908W
1650W
3000W
5Hz to 20kHz
5Hz to 80Hz
8V to 16V
82dB
0,2V to 4V
150A
302A
79%
80
9" x 10.2" x "3.9
2 AWG (35mm²)
2 x 13 AWG (1,5mm²)
150A
150Ah
5.7lbs
80Hz to 20kHz
3000.1D NAN0 2Ω
1650W
3000W
N/A
5Hz to 20kHz
5Hz to 80Hz
8V to 16V
83dB
0.2V to 4V
150A
302A
79%
80
9" x 10.2" x "3.9
2 AWG (35mm²)
2 x 13 AWG (1,5mm²)
150A
150Ah
5.7lbs
80Hz to 20kHz
DIMENSIONS
High Pass Filter
A
B
C
D
7.4"
6.3"
8.8"
8"
E
2.8"
Net weight
4.4lbs
B
C
D
A
E
6
190mm
160mm
225mm
204mm
71,5mm
2kg

DISMANTLING / MOUNTING
CAREFULLY pull out the top of plastic cover to release the upside latches, as shown in the picture.
In a continuous movement, slide up the plastic cover, removing it.
The cover is removed.
1 2 3
DISMANTLING
MOUNTING
1
2
3
Gently press the top of plastic cover against the amplifier until hear a CLICK noise of upside latches.
Approach the plastic cover to amplifier profile in way to perfect fit of points A and B, and slide it down.
PT
A
B
4 5
4
5
7

LIMITED WARRANTY
8
ŸMaintenance made by unauthorized personnel;
ŸProducts purchased more than 12 months ago.
SounDigital warrants the original purchaser that this product shall be free of defects in materials an workmanship
for a period of twelve (12) months from the original date of purchase. Some countries have extended warranty in
case the product is installed by an authorized dealer. This warranty is not transferrable and applies only to the
original customer from an authorized SounDigital dealer.
Warranty is void when:
ŸAlteration or removal of the seal/serial number;
ŸDamage caused by fall, impact or natural depreciation, caused by transport and/or handling, risks, or
smashings;
ŸDefect or problem caused by misuse of the product;
ŸIncorrect installation or non-conformity with the Manual;
ŸExposure to adverse conditions (weather, humidity, etc);
Ÿ If you need service on your SounDigital product, send it to SounDigital's Amplifier Repair Center through an
authorized SounDigital dealer (must be accompanied by proof of purchase);
Ÿ Any extra information you can get by contacting us at the e-mail address: [email protected];
Ÿ Workmanship/service needed to repair the equipment;
Ÿ New modifications/iterations on a product don't obligate the manufacturer to modify products formerly
produced.
Ÿ In case of manufacturing defect or bad quality of raw material, the max compensation will be the replacement
of the product, not allowing any kind of compensation payment;
Warranty covers:
Ÿ Component or material with manufacturing defects;