SOUNDMASTER MCD-7510USB User manual

Modell MCD-7510USB
Bitte vor Inbetriebnahme sorgfälltig lessen
Read instructions carefully before using the unit
Avant de metre en service votre appareil, lisez attentivement ce instructions

LOCATION OF CONTROLS
1) LCD DISPLAY
2) POWER LED INDICATOR
3) CD PLAY/PAUSE / STOP BUTTON
4) CD SKIP / TUNING UP /DOWN BUTTON
5) RECORD BUTTON
6) FUNCTIONS SELECTOR
7) BAND / FM MODE SELECTOR
8) USB SOCKET
9) STEREO HEADPHONE JACK
10) SD/MMC CARD SLOT
11) CASSETTE DOOR
12) TAPE RECORDING KEY
13) TAPE PLAY KEY
14) TAPE REWIND KEY
15) CD DOOR OPEN BUTTON
16) REMOTE SENSOR
17) MP3 FOLDER UP BUTTON
18) SOURCE BUTTON
19) TUNING KNOB
20) VOLUME UP BUTTON
21) VOLUME DOWN BUTTON
22) X-BASS ON/OFF BUTTON
23) TAPE PAUSE KEY
24) TAPE STOP/EJECT KEY
25) TAPE FAST FORWARD KEY
26) CASSETTE KEY COVER
27) FM WIRE ANTENNA
28) SPEAKER WIRE CONNECTOR (L/R)
29) AC POWER CORD
CAUTION:
USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.
IMPORTANT:
SINCE MOVEMENT OF THE CD MECHANISM AND THE SENSITIVE CIRCUITY MAY CAUSE INTERFERENCE TO
THE RADIO TUNER NEARBY, SWITCH THIS UNIT OFF WHILE OPERATING OTHER RADIO DEVICES.
PRECAUTION FOR USE
INSTALLATION
•UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.
•DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAIN VOLTAGE AND BEFORE ALL
OTHER CONNECTIONS HAVE BEEN MADE.
•DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS
AROUND THE UNIT FOR VENTILATION.
CONNECTION
1. CONNECT THE POWER CORD (29) TO AC OUTLET
2. CONNECT THE SPEAKER WIRE TO THE SPEAKER TERMINAL (28) LOCATED ON THE REAR SIDE OF THE
UNIT.
3. TURN ON THE POWER AND SELECT “ CD/USB/SD “ FUNCTION (6). IF THE LCD DISPLAY (1) IS ON WITH
BACKLIGHTING, IT MEANS THE POWER SUPPLY IS NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE
MUSIC.
LISTENING TO RADIO
OPERATION
1. SET THE FUNCTION SELECTOR TO “ TUNER ” (6) POSITION.
2. SELECT THE DESIRED RADIO FREQUENCY BAND FROM BAND SELECTOR (7).
3. TURN THE TUNING KNOB (19) TO SET THE STATION FREQUENCY AS DESIRED.
4. ADJUST VOLUME CONTROL (20,21) FOR THE DESIRED VOLUME LEVEL.
E-1

HINTS FOR BEST RECEPTION:-
- AM : THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM/LW RECEPTION IS WEAK, SLIGHT ROTATE
OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
- FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
PLAYING COMPACT DISC
zGETTING START
1. TURN FUNCTION SELECTOR (6) TO SELECT “ CD/USB/SD ” MODE.
2. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR.
3. FOCUS SEARCH IS PERFORMING, THE LCD DISPLAY (1) WILL SHOW THE TOTAL NUMBER OF TRACKS &
TOTAL PLAYING TIME.
zPLAY / PAUSE / STOP MODE
1. PRESS THE “ PLAY/PAUSE/STOP ” BUTTON (3) TO START PLAYBACK, THE FIRST TRACK WILL START
PLAYBACK.
2. TO INTERRUPT, PRESS THE “ PLAY/PAUSE/STOP ” BUTTON (3) ONCE, THE PLAYING TIME WILL BE FREEZE
& FLASHING ON THE LCD DISPLAY (1). PRESS AGAIN TO RESUME NORMAL PLAYBACK.
3. IF PRESS AND HOLD THE “ PLAY / PAUSE STOP “ BUTTON (3) FOR OVER 2 SECONDS DURIGN PLAYBACK
MODE. THE SYSTEM WILL GO TO STOP MODE.
zSKIP/SEARCH MODE (SKIP/SEARCH UP / SKIP/SEARCH DOWN )
1. DURING PLAY OR PAUSE MODE, IF “SKIP UP” BUTTON (4) IS PRESSED. IT WILL GO TO NEXT TRACK AND
DISPLAY THE TRACK NO. AND THEN REMAIN THE PLAY OR PAUSE MODE.
2. DURING PLAY OR PAUSE MODE, IF “SKIP DOWN” BUTTON (4) IS PRESSED. IT WILL GO BACK TO THE
BEGINNING OF THE TRACK, ORIGINAL TRACK NO. IS DISPLAY AND REMAIN THE PLAY OR PAUSE MODE.
3. AFTER STEP 2, PRESS “SKIP DOWN” BUTTON (4) AGAIN WILL GO TO THE PREVIOUS TRACK AND REMAIN
THE PLAY OR PAUSE MODE.
4. IF PRESS AND HOLD THE “ SKIP UP/DOWN BUTTON “ (4) DURING CD/MP3 PLAYABCK, THE PLAYING TRACK
WILL GO FAST FORWARD OR BACKWARD UNTIL THE BUTTON BEING RELEASED.
zFOR MP3/WMA DISC
1. PRESS “ FOLDER UP “ BUTTON (17), THE FOLDER NO. WILL GOES UP
2. PRESS “ SKIP UP “ OR SKIP DOWN (4) BUTTON, THE TRACK NO. CHANGE.
3. WHEN THE DESIRED TRACK IS BEING SELECTED, PRESS THE CD “ PLAY/PAUSE/STOP ” BUTTON (3) TO
START PLAYBACK.
ID3 (TRACK/ALBUM TITLE) FUNCTION (BY REMOTE HANDSET)
1. PRESS THE “ INFO “ BUTTON DURING PLAYBACK OF MP3/WMA DISC, THE SONG TITLE IS BEING
DISPLAYED. PRESS THE “ INFO ” BUTTON AGAIN TO DISABLE THE FUNCTION.
SONG TITLE/FOLDER NAME SEARCH FUNCTION (BY REMOTE HANDSET)
YOU CAN SEARCH THE TRACK BY THE TITLE/FLODER NAME IN DISC DURING STOP MODE:-
1. PRESS THE “ FIND “ BUTTON ONCE, THEN PRESS THE “SKIP UP” (OR SKIP DOWN) BUTTON (4), YOU CAN
SEARCH THE TITLE OF EACH SONG ONE BY ONE UNDER ALPHABET ORDER ON LCD DISPLAY, THEN
PRESS THE CD “ PLAY/PAUSE/STOP ” BUTTON (3) TO START THE PLAYBACK OF THE SELECTED TRACK.
2. PRESS AGAIN “ FIND ” BUTTON, THE FOLDER NAME IS BEING DISPLAYED. THEN PRESS THE “SKIP UP” (OR
SKIP DOWN) BUTTON TO SELECT THE DESIRED FOLDER, AND PRESS THE CD“ PLAY/PAUSE/STOP ”
BUTTON (3) TO START THE PLAYBACK OF ALL TRACKS INSIDE THAT SELECTED FOLDER.
REMARK:-
- IN THAT CASE OF NO NAME HAD BEEN ASSIGNED FOR THE TRACK, “ NONE “ OR “ UNKNOWN “ IS BEING
DISPLAYED” ON DISPLAY (1).
- THE LCD DISPLAY SUPPORT ENGLISH LANGUAGE ONLY
MP3/WMA TRACK FORMAT REQUIREMENT:-
- MP3 BIT RATE : 32 KBPS~256 KBPS AND WMA BIT RATE : 32 KBPS ~ 320 KBPS
- THE PERFORMANCE OF PLAYING MP3 DISC IS VARIOUS FROM THE QUALITY OF RECORDING DISC AND
THE METHOD OF RECORDING. FURTHERMORE, THE SEARCHING LEAD-TIME FOR MP3-CD IS LONGER
THAN NORMAL CD DUE TO DIFFERENCE FORMAT.
zREPEAT/INTRO/RANDOM MODE (BY REMOTE HANDSET)
PRESS THE REPEAT/INTRO/RANDOM BUTTON BEFORE OR DURING PLAYBACK, A SINGLE TRACK, SINGLE
FOLDER (MP3 ONLY) OR ALL THE TRACKS CAN BE PLAYED IN DIFFERENCE MODE AS FOLLOW:-
E-2

FOR CD
(1) REPEAT 1 (2) REPEAT ALL TRACK (3) INTRO (4) RANDOM (5) OFF MODE
INDICATOR
PLAY MODE ON LCD DISPLAY
REPEAT TRACK
REPEAT ALL ALL
INTRO INTRO
RANDOM RAN.
OFF MODE --------------
FOR MP3/WMA DISC
(1) REPEAT 1 (2) REPEAT 1 FOLDER (3) REPEAT ALL FOLDER
(6)OFFMODE (5)RANDOM (4) INTRO PLAY
INDICATOR
PLAY MODE ON LCD DISPLAY
REPEAT SINGLE TRACK
REPEAT ALL TRACKS ALL
REPEAT SINGLE FOLDER
INTRO PLAY MODE INTRO
RANDOM MODE RAN.
OFF MODE -----------------
zREPEAT PLAY
YOU CAN LISTEN THE DESIRED TRACKS OR FOLDER REPEATEDLY BY THIS FUNCTION.
zINTRO PLAY
YOU CAN LISTEN THE BEGINNING (10 SECONDS) OF EACH TRACK IN A CD BY THIS FUNCTION &
SAVING YOUR TIME TO SEARCH THE DESIRE SONG
zRANDOM PLAY
YOU CAN LISTEN ALL THE TRACKS OR FOLDER IN A RANDOM ORDER BY THIS FUNCTION
CD/MP3 DISC PROGRAMMING (BY REMOTE CONTROL)
UP TO 32 TACKS CAN BE PROGRAMMED FOR CD OR MP3 FILE AND PLAY IN ANY ORDER. BEFORE USE, BE
SURE THE SYSTEM IS AT STOP MODE BEFORE PROGRAMMING:-
1. SET IN CD/USB MODE & STOP THE CD PLAYBACK.
2. PRESS THE “PROGRAM” BUTTON, “ PROGRAM “ WILL APPEAR ON LCD DISPLAY (1). MOREOVER, IT WILL
INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED.
3. SELECT A DESIRED TRACK BY PRESSING SKIP UP OR DOWN BUTTONS (4).
4. PRESS THE “ PROGRAM ” BUTTON TO STORE THE TRACE INTO MEMORY.
5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS CD “ PLAY/PAUSE/STOP ”
BUTTON (3) TO PLAY THE DISC IN ASSIGNED ORDER.
7. TO CANCEL THE PROGRAMMED FILE, PRESS “STOP” BUTTON ON REMOTE HANDSET UNTIL “ PROGRAM
“ IS DISAPPEAR ON LCD DISPLAY (1)
LISTING TO TAPE
GENERAL OPERATION
STOP / EJECT KEY (24) PRESS TO STOP ALL DECK OPERATION. PRESS AGAIN TO OPEN THE CASSETTE
DOOR
FAST FORWARD KEY (25) PRESS TO START TAPE WINDING IN EITHER FORWARD OR REVERSE DIRECTION
& FAST REWIND KEY (14)
PLAY KEY (13) PRESS TO START PLAYING CASSETTE TAPE
PAUSE KEY (23) PRESS TO STOP TAPE OPERATION TEMPORARILY. PRESS AGAIN TO RESUME
PLAYBACK
RECORD KEY (12) PRESS TOGETHER WITH PLAY KEY TO START TAPE RECORDING
E-3

PLAYBACK
zSELECT “FUNCTION” BUTTON (6) TILL IT REACH “ TAPE ” MODE.
zINSERT THE CASSETTE TAPE.
zPRESS PLAY KEY (13) TO ACTIVE PLAYBACK
zADJUST THE VOLUME BUTTON (20,21) TO THE DESIRED LEVEL.
zUSE PAUSE KEY (23) WHEN YOU WANT TO STOP PLAYBACK TEMPORARILY.
zPRESS STOP / EJECT KEY (24) WHEN FINISHED.
RECORDING
A. RECORDING FROM RADIO
zSET TO “RADIO” MODE.
zTUNE TO THE DESIRED STATION AND INSERT A BLANK CASSETTE TAPE.
zPRESS “RECORD” KEY (12) TO START RECORDING.
zPRESS “PAUSE” KEY (23) AND THEN “STOP/EJECT” KEY (24) WHEN FINISHED.
B. RECORDING FROM CD/USB/SD
zSET TO “CD/UDISK/SD/MMC” MODE.
zINSERT A BLACK CASSETTE TAPE WHICH IS SUITABLE FOR RECORDING.
zPRESS “PAUSE” KEY (23) FIRST AND THEN “RECORD” KEY (12), RECORDING FUNCTION IS NOW STANDBY.
zSTART PLAYBACK OF CD/USB/SD, AND THEN RELEASE THE “PAUSE KEY” (23) TO START RECORDING.
zTO STOP RECORDING, PRESS “STOP” BUTTON (5) FIRST, THEN PRESS THE “PAUSE” KEY (23) AND THEN
“STOP/EJECT” KEY (24) ON CASSETTE TAPE DECK.
PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 /WMA FILE WHICH STORED IN THE MEMORY
MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.
1. SET FUNCTION SELECTOR (6) AT CD/USB/SD MODE AND THEN
PRESS SOURCE BUTTON (18) TO SELECT “ USB OR CARD” MODE.
2. PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING
INTO COMPLETELY OR INSERT THE MEMORY CARD IN THE
DIRECTION OF THE ARROW AS SHOWN IN THE LABEL ON THE
UNDERSIDE OF THE MEMORY CARD SLOT COVER. INSERT
STRAIGHT WITHOUT BENDING.
zCONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD
DAMAGE THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB
THUMB DRIVE / SD/MMC CARD). CHECK TO BE SURE THE
DIRECTION IS CORRECT BEFORE CONNECTION.
3. THE SYSTEM WILL START READING THE STORAGE MEDIA
AUTOMATICALLY AFTER CONNECTING, AND LCD DISPLAY (1) WILL
SHOW THE TOTAL NUMBER OF MP3/WMA FILES AND TOTAL NUMBER
OF FOLDER BEING DETECTED.
4. REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3
DISC AS ABOVE
REMARK
- THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 AND WMA FORMAT ONLY THOUGH THE USB
PORT.
- IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3 ENCODING
FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS NOT A
MAUFUNCTION OF THE SYSTEM.
ENCODING OF CD/PHONO INTO MP3 FILE
THE SYSTEM IS ABLE TO ENCODE NORMAL CD OR CASSETTE TO MP3 FORMAT AND RECORDING AT MEMORY
MEDIA WITH USB CONNECTING PORT OR SD/MMC CARD.
A) CD ENCODING
I) ECNODING 1 TRACK
1. PERFORM NORMAL PLAYBACK OF THE CD TRACK YOU WANT TO ENCODE & RECORD,
2. PRESS “ RECORD “ BUTTON (5) DURING THE PLAYBACK OF THE DESIRE TRACK, UNIT WILL DISPLAY
“ USB “ & “ “ AND FLASHING. ENCODING IS PERFORMING NOW.
3. AFTER COMPLETING OF ENCOD, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
E-4

II) ENCODING 1 DISC
1. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR
2. PRESS THE “ RECORD “ BUTTON (5) AFTER FOCUS SEARCH COMPLETED. UNIT WILL DISPLAY “
“ & “ “ AND FLASHING. ENCODING IS PERFORMING NOW.
3. AFTER COMPLETING OF ENCODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
NOTED : IF BOTH SOURCE “ USB “ OR “ SD “ BEING OCCUPIED BY HARDWARE, YOU NEED TO SELECT WHICH
SOURCE TO BE RECRODING THE FILE BY PRESSING SKIP FORWARD OR SKIP BACKWARD
BUTTON AND THEN “ RECORD “ BUTTON AGAIN TO START THE RECORIDNG.
REMARK:-
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE CD TRACK
- THE SYSTEM WILL CREAT A “ AUDIO “ FOLDER AND THEN STORE THE ENCODING TRACK IN IT.
- THE RECORDING FORMAT IS PRESET AT – MP3 BIT RATE : 128 KBPS, SAMPLING RATE : 44.1KHZ
- NO SONG TITLE WILL BE RECORDED DURING ENCODING MODE
- TO INTERRUPT THE RECRODING, PRESS THE “ RECORD “ BUTTON AGAIN DURING RECORD MODE.
- RECORDING WILL BE COMPLETED ONLY ENTIRE SONG BEING ENCODED, IF TERMINATE THE ENCODING
PROCESS INTERMEDIATELY, THERE IS NO TRACK BEING RECORDED NOR STORED TO THE USB OR
SD/MMC CARD
IV) COPYING OF MP3/WMA FILE
IF PUTTING A MP3/WMA DISC INSTEAD OF A CD-DISC, THE SYSTEM WILL COPY THE FILES TO THE USB OR
SD/MMC CARD IF PRESS THE “ RECORD “ BUTTON (5). THE OPERATION PROCEDURES IS SAME AS CD
ENCODING AS STIPULATE ON ABOVE, AND THE SYSTEM WILL SWITCH TO COPYING MODE ONLY IF MP3/WMA
FILE BEING READ.
REMARK:
- THE SYSTEM WILL STORE THE FILE INTO USB SORCE FIRST IF BOTH USB AND SD SLOT ARE BEING
OCCUPLIED BY STORAGE MEDIA.
- IF PRESS THE “ RECORD “ BUTTON DURING PLAYBACK OF USB OR SD SOURCE, THE FILE WILL COPY
FROM USB TO SD OR SD TO USB.
B) CASSETE ENCODING
1. SET THE FUNCTION BUTTON (5) TO “ TAPE “ MODE AND THEN PRESS THE “ RECORD “ BUTTON (5)
DIRECTLY.
2. THE LCD DISPLAY WITH SHOW THE WORD “ USB “ OR “ CARD “ AND “ “ & FLASHING, NOW THE
SYSTEM IS STARTING THE ENCODING MODE.
3. START PLAYBACK OF CASSETTE TAPE WHICH THE TRACK YOU PREPARE TO RECORD.
4. AFTER FINISH OF RECODING, PRESS AND HOLD THE “ RECORD “ BUTTON (5) UNTIL THE LCD STOP
FLASHING AND RETURN TO “ TAPE “ MODE.
C) ENCODING BITRATE (BY REMOTE HANDSET)
YOU CAN SELECT THE DESIRED BITRATE DURING ENCODING FROM CD OR PHONO TO USB, THE
SELECTABLE RANGE FROM 32 / 64 /96 /128 / 192 / 256 KBPS.
1. SET IN “ TAPE “ FUNCTION (6) & REMAIN STOP MODE.
2. PRESS THE “ INFO “ FUNCTION AND THE LCD DISPLA WILL SHOW THE DEFAULT BITRATE (128 KBPS)
3. PRESS SKIP OR BUTTONS (4) TO SELECT THE DESIRED BITRATE FOR ENCODING.
4. PRESS AGAIN THE “ INFO “ TO CONFIRM THE SETTING AND THE LCD DISPLAY (1) RESUME TO “ TAPE
“ MODE
FILE DELETE AT USB / SD CARD (BY REMOTE CONTROL)
THE SYSTEM IS ABLE TO ERASE THE FILE STORED INSIDE THE USB PEN DRIVE OR SD CARD BY
FOLLOWING:-
A) SINGLE FILE DELETE
1. PRESET AT “ USB “ OR “ SD “ MODE.
2. PRESS AND HOLD THE “ INFO “ BUTTON FOR 3 SECONDS AND THE LCD DISPLAY (18) WILL SHOW (DEL
---001)
3. PRESS SKIP FORWARD OR SKIP BACKWARD BUTTON TO SELECT THE FILE GOING TO DELETE
4. PRESS THE “ REC “ BUTTON TO ENTER “ YES / NO “ MODE AND THEN PRESS SKIP FORWARD OR SKIP
BACKWARD TO SELECT “ YES “ OR “ NO “.
5. PRESS THE “ REC “ BUTTON AGAIN TO CONFIRM THE SETTING.
E-5

B) ALL FILES DELETE
1. PRESET AT “ USB “ OR “ SD “ MODE.
2. PRESS AND HOLD THE “ INFO “ BUTTON FOR 3 SECONDS AND THE LCD DISPLAY (18) WILL SHOW (DEL
---001)
3. PRESS AND HOLD THE “ INFO “ BUTTON TO ENTER “ YES / NO “ MODE AND THEN PRESS SKIP
FORWARD OR SKIP BACKWARD TO SELECT “ YES “ OR “ NO “.
4. PRESS THE “ REC “ BUTTON AGAIN TO CONFIRM THE SETTING.
REMARK :
- ALL THE FILES INSIDE THE USB STORAGE MEDIA OR SD CARD WILL BE DELETED COMPLETELY AFTER
CONFIRMING TO “ YES “ MODE.
- PRESS “ STOP “ BUTTON ONCE AT REMOTE HANDSET TO QUITE DELETE MODE
REMOVING OF USB / MEMORY CARD
TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO EITHER
CD, AUX OR TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET DIRECTLY, FOR
MEMORY CARD – PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD BEING PARTIALLY
EJECT AND YOU CAN REMOVE IT BY HAND.
REMARK : NEVER DISCONNECT THE MP3 / USB PEN-DRIVE OR SD/MMC CARD DURING PLAYBACK OR
RECRODING. THIS WILL CAUSE DAMAGE OF STORED FILE OR THE HARD WARE.
REMOTE CONTROL TRANSMITTER
BATTERY INSTALLATION (BATTERY NOT PROVIDED)
THE INFRA-RED TRANSMITTER REQUIRES 2 PC AAA SIZE BATTERY FOR OPERATION
BUTTON DESCRIPTION
1) FIND IN MP3/WMA MODE, PRESS TO ACTIVE FILE/FOLDER
NAME SEARCH FUNCTION.
2) INFO IN CD/USB STOP MODE, PRESS TO SELECT
ENCODING BITRATE
3) REC IN CD OR PHONO MODE, PRESS TO ACTIVE
RECRRDING FUNCTION
4) REP/INTRO/RAN IN CD/USB MODE, PRESS TO ACTIVE REPEAT / INTRO
/ RANDOM FUNCTION
5) PROGRAM IN CD/USB MODE, PRESS TO ACTIVE PROGRAMMING
FUNCTION
6) PLAY/PAUSE IN CD/USB MODE, PRESS ONCE TO START PLAYBACK.
PRESS AGAIN TO ENTER PAUSE MODE.
7) SKIP/SEARCH FORWARD PRESS ONCE TO SKIP TO NEXT TRACK, PRESS &
HOLD FOR SEARCH FORWARD
SKIP/SEARCH BACKWARD PRESS ONCE TO SKIP TO PREVIOUS TACK.PRESS & HOLD FOR SEARCH
BACKWARD
8) STOP IN CD/USB MODE, PRESS TO STOP PLAYBACK OR CANCEL THE STORED
PROGRAM.
9) FOLDER UP /DOWN IN MP3 MODE, PRESS TO SELECT FOLDER UP OR DOWN
10) SOURCE IN CD/USB MODE, PRESS TO SELECT CD OR USB FUNCTION REPEATLY
Technic FM frequency 87,5 – 108MHz
AM frequency 540 – 1600KHz
MP3 encoding Bitrate 32-256 KBPS
Power output 2 x 50W P.M.P.O.
Power consumption 15W
AC 230V 50Hz
E-6