SOYO SY-6BA+ User manual

Quick Start Guide for SY-6BA Pentium®II Motherboard
* All brand names and trademarks are the properties of their respective owners.
Congratulations on your purchase of the SOYO™SY-6BA Pentium® II supported Motherboard.
This Quick Start Guide describes the steps for installing and setting up your new motherboard.
This guide is designed for those users who have prior knowledge of motherboard operations and are already
familiar with basic motherboard settings. For further information, please refer to SY-6BA Motherboard User's
Guide and Technical Reference online manual included on the CD-ROM packed with your motherboard.
1Unpack the Motherboard
When unpacking the motherboard, check for the following items:
θThe SY-6BA 82440 BX AGP Set Motherboard
θThis Quick Start Guide
θThe Installation CD-ROM
θOne IDE Device Flat Cable
θOne Floppy Disk Drive Flat Cable
θThe CPU Retention Set
2Motherboard Layout
Your new SY-6BA Motherboard is a high-performance Pentium® II processor supported system board that features
state-of-the-art technology, as shown on the following layout. This layout helps you identify the motherboard
elements that you will be dealing with during the installation.
Default Settings
CPU: Pentium® II processor 233/350 MHz
CPU Voltage: Auto Detect CPU Voltage
2 PCI E-IDE Ports
1 Parallel Port LPT1 EPP/ECP Printer Port
ØLPT1: I/O Address 378H, IRQ 7,
Status ECP+EPP
2 Serial Ports COM1 & COM2:
ØCOM1: I/O Address 3F8H, IRQ 4
ØCOM2: I/O Address 2F8H, IRQ 3
2 Onboard USB Ports
PS/2 Mouse
ATX Power Supply
COM 1
COM 2
PRT
USB 1
USB 2
PS/2 KB
Connector
PS/2 Mouse
Connector
Flash BIOS
PCI Slot #1
PCI Slot #2
PCI Slot #3
PCI Slot #4
PCI Slot #5 (Slave)
AGP Port
ISA Slot #1
ISA Slot #2
IR1
JP5
3V Lithium
Battery
Intel®
82443 BX
IO Chipset
CPUFAN PWRFAN
CHAFAN
JP44
1
3
1 3
1
Intel®
82371 EB
SB-LINK™
®
II
Processor
All manuals and user guides at all-guides.com
all-guides.com

ROM PCI/ISA BIOS
CHIPSET FEATURES SETUP
AWARD SOFTWARE, INC.
CPU Host Clock Select : 66 MHz
CPU Freq. (MHz) : CPU Host Clock * 3.5
CPU Warning Temperature
Current CPU Temperature
Current System Temp.
Current CPUFAN Speed
Current PWRFAN Speed
Current CHSFAN Speed
: Disabled
: 29°C/84°F
: 24°C/75°F
: 6553 RPM
: 6553 RPM
: 6553 RPM
VID(V)
3.3(V)
+12(V)
-5(V)
: 2.78 V
: 3.31 V
: 11.84V
: -4.88V
VTT(V)
+5 (V)
-12 (V)
: 1.50V
: 4.97V
: -11.45V
ESC
F1
F5
: Quit
: Help
: Old Values
↑↓→←
PU/PD/+/-
(Shift) F2
: Select Item
: Modify
: Color
Auto Configuration
SDRAM CAS latency Time
DRAM Data Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Video RAM Cacheable
8 Bit I/O Recovery Time
16 Bit I/O Recovery Time
Memory Hole At 15M-16M
Passive Release
Delay Transaction
AGP Aperture Size (MB)
: Enabled
: 3
: Non-ECC
: Disabled
: Disabled
: Disabled
: 1
: 1
: Disabled
: Enabled
: Disabled
: 64
F6
F7 : Load BIOS Defaults : Load Setup Defaults
3Jumper Settings and Connectors
CMOS Clear: JP5 PCI Audio Card Connector: SB-Link
Retain CMOS
data (default) 1-2 Some PCI audio cards needs a DMA channel. Connect the cable to SB-Link.
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Power Supply Fan: PWRFAN
Wake-On-LAN Jumper: JP44 Pin 123Clear CMOS data 2-3
Connect the WOL cable from your LAN card
to JP44. Function GND 12V Sensor
USB TB LED SPK RESET IDE LED KB-LOCK
Connect your
USB devices to
this header
Connect your
Turbo LED to this
jumper
Connect the speaker
cable to this jumper Connect the reset button to this jumper Connect the IDE device LED to this
jumper
Connect the Power
LED and the
Keyboard Lock
switch to
IrDA (Infrared Device Connector): IR ATX Power On/Off: PWRBT ATX Power: ATX PW
Connect your IrDA device to this connector Connect your power switch to this
jumper (momentary switch type) Attach the ATX Power Supply to this connector
4Memory configuration
Your board comes with four DIMM sockets, providing support
for up to 512MB of main memory using DIMM modules from
8MB to 128MB. For 66MHz host bus CPUs use 12ns or faster
DIMM modules; for 100MHz host bus CPUs use 8ns modules.
Memory configuration Table
Number of
Memory
Modules
DIMM 1 DIMM 2 DIMM 3 DIMM 4
11st
22nd 1st
33rd 2nd 1st
44th 3rd 2nd 1st
Note: It is of prime importance that you install DIMM
modules as outlined in the table above in order to preserve
signal integrity on 100MHz host bus systems.
5Default I/O Settings
Default settings for multi-I/O addresses are as
follows:
Port I/O Address IRQ Status
LPT1 378H 7ECP + EPP
COM1 3F8H 4
COM2 2F8H 3
Note: If a default I/O address conflicts
with other I/O cards such as sound card, you
must change one of the I/O addresses to
remedy to this address conflict. (I/O addresses
can be adjusted from the BIOS Setup Utility
under [Integrated Peripherals].)
6CPU Settings
Enter the BIOS Setup Utility [CHIPSET FEATURES SETUP] section and configure the CPU frequency settings to
match the working frequency of your Pentium® II processor. Follow these steps to configure the CPU settings:
Step 1. In BIOS, select the correct Host Clock frequency of your CPU.
Step 2. Note the working frequency of your Pentium® II
processor that should be clearly marked on the cover.
Step 3. Configure CPU Freq. field in BIOS by selecting the
Multiplier that matches the Host Clock with your CPU
working frequency, as shown in the following table:
CPU Host Cock (MHz) XMultiplier =CPU Frequency (MHz)
66 X3.5 =233
66 X4.0 =266
66 X4.5 =300
66 X5=330
100 X3.5 =350
100 X4=400
100 X4.5 =450
100 X5=500
All manuals and user guides at all-guides.com