SPALDING U-Turn Lift System User manual

Toll-Free Customer Service Number
U.S.: 1-800-558-5234
Canada: 1-800-284-8339
Europe: [phone]
Australia: 1300 367 582
www.spalding.com
05/21 ID# M3160013
Model Number:
(found on product box)
WARNING
READ AND UNDERSTAND THE OPERATOR’S
MANUAL BEFORE USING THIS UNIT.
FAILURE TO FOLLOW THE OPERATING
INSTRUCTIONS COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
UNIVERSAL ELEVATOR MOUNT
Owner’s Manual

Contents
2
Contents
Contents .........................................2
Before You Begin..................................2
Contact ..........................................2
Warranty.........................................3
Safety Information ................................3
Test-Fit Close Tolerance Bolts .......................4
Package Contents.................................4
Tools & Materials for Assembly......................7
Assemble the Elevator Mount .......................8
Assemble the Elevator Structure/Mechanism ........15
Backboard Mounting .............................19
Operation .......................................21
Parts List .......................................22
Questions or Missing Parts?
Call TOLL-FREE Customer Service
Number listed on the front page!
DON’T go back to store!
Before You Begin
READ AND UNDERSTAND THE OPERATOR’S MANUAL
BEFORE USING THIS UNIT.
• Remove ALL contents from boxes.
• Be sure to check INSIDE pole sections; hardware and
additional parts are packed inside.
• This manual, accompanied by a sales receipt, should be
saved and kept on hand as a convenient reference, as it
contains important information about your model.
WARNING
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR PROPERTY DAMAGE.
Contact
Questions or missing parts? Do NOT go back to the store!
Email: [e-mail]
Customer Service
Toll-Free Number: 1-800-558-5234
Mailing Address: Spalding
PO Box 90015
Bowling Green, KY 42102

Warranty
3
Warranty
For the very latest Basketball System Warranty information, please visit www.Spalding.com or call
Spalding Customer Service at 1-800-558-5234.
Safety Information
WARNING
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND
WILL VOID THE WARRANTY.
Owner must ensure all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check the entire box
and inside all of the packing material for parts and/or additional instruction material. Before beginning assembly, read
the instructions and identify parts using the hardware identier and parts list in this document. Proper and complete
assembly, use, and supervision are essential for proper operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed, maintained, and operated properly.
• If using a ladder during assembly, use extreme caution.
• Check the base regularly for leakage. Slow leaks could cause the system to tip over unexpectedly.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play
and/or during transport of the system.
• Climate, corrosion, or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6'-6" (1.98 m) to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE
• Adult assembly required.
• Dispose of ALL packaging materials promptly.
• As with all products, periodically inspect for loose, small parts.
• Assembled unit MUST be lled with sand or water at ALL times.
• ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed according to
instructions.
• Failure to follow instructions could result in SERIOUS INJURY.
• It is NOT acceptable to devise a makeshift support system.
NOTE
Mount, pole, and backboard style will vary.

Test-Fit Close Tolerance Bolts
4
Test-Fit Close Tolerance Bolts
To ensure optimal playability of the backboard system, a close tolerance t between the elevator components and
hardware is required. Test-t large bolts into large holes of elevator tubes, backboard brackets, and triangle plates.
Carefully rock them in a circular motion to remove any excess paint from holes, if necessary.
NOTE
Not all items pictured are included with every model.
Package Contents
Check the contents of each kit and other parts to ensure that all components are present. Keep the kit hardware in
the labeled bag as they will be used in different assembly steps.
See "Parts List" on page 22 for a complete list of replacement part numbers.
BOLTS AND SCREWS
R 1.8145.97
4.00 101.60
4.68 118.87
1.75 44.45
2.00 50.80
5.00 127.00
1.75 44.45
4.06 103.12
4.56 115.82
1/2-13 THREAD
#5
#3
#14
#6
#29
#1
1U-Bolt, Round 3/8-16 x 4.68 (x2) 3Bolt, Hex Head, 5/16-18 x 1-1/4”
Long (x6) 5Bolt, Hex Head, 1/4-20 x 2-1/4” Long (x1)
6Bolt, Hex Head, 1/2-13 x 7”
Long (x5) 14 Spacer, 1.8 Long (x1) 29 U-Bolt, Square, 1/2-13 x 5 (x2)

Package Contents
5
NUTS AND WASHERS
#8
#13
202651 0.53” ID x 1” OD
#10
#9
#34
Ø.52 13.08
Ø1.00 25.40
.13 3.18
#32
203099Hex Locknut (Nylon Insert) 5/16-18
#11
#33
8Locknut, Hex Head, 1/2-13 (x9) 9Washer, Flat, 5/16 (x12) 10 Washer, Flat, 1/2 (x10)
11 Locknut, Nylon Insert, 5/16 (x6) 13 Nut, Hex, Locking 1/4-20 (x1) 32 Washer, Flat, Nylon (x4)
33 Locknut, Nylon Insert, 3/8-16 (x4) 34 Washer, 3/8 (x4)
SPACERS
#4
206269 spacer 1/2 id, 3/4 od X 4 Long
#16
#15
#25
#31
4Spacer, 1.8 Long (x1) 15 Spacer, Plastic, 1” Long (x4) 16 Spacer, Metal, .75 O.D., 4” Long (x3)
25 Spacer, Plastic, .73 O.D., 1.7” Long
(x2) 31 Spacer, Metal .3.5” Long (x2)

Package Contents
6
MOUNTING BRACKET HARDWARE
U-TURN : ADJUSTMENT
509000
Size = 4" x 3.25"
Corner Radius = 3/8"
Die Cut Label
3.25 Mil Vinyl
All Temp. Permanent Adhesive
1 Mil. Polypropolyne Overlaminate
Illustrator CS2 = EPS
Backing + 1/16 Circumference
Rolls of 500
Crank
Height
Indicato
r
Hook
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
Position looped end of
crank onto hook as shown.
Rotate crank handle to
raise or lower backboard
509000 1/07
#2
#18 #19
#20
#21
#22
#24 #26 #27
#30
#35
#23 #17
#12
2Clamp, Saddle (x2) 12 Label, Height-Adjustment (x1) 17 Bracket, Pole (x1)
18 Bracket, Jack Support, RIGHT (x1) 19 Bracket, Jack Support, LEFT (x1) 20 Bracket, Elevator (x2)
21 Sleeve, Plastic, Height-Indicator (x1) 22 Handle Assembly, Crank (x1) 23 Struts, Board Support (x2)
24 Screw Jack Assembly (x1) 26 Bracket, Angle, RIGHT (x1) 27 Bracket, Angle, LEFT (x1)
30 Tube, Elevator (x1) 35 Bracket, Board (x2)

Tools & Materials for Assembly
7
Tools & Materials for Assembly
NOTE
Due to various mounting methods, additional tools and materials may be required.
2 Capable Adults Tape Measure Step Ladder (8 ft.) Level Pencil
Drill and Drill Bit (3/8") Needle-Nose Pliers Socket Wrench
Extension
Wrench
7/16", 1/2", 9/16", 3/4"
(OPTIONAL)
Adjustable Wrenches
NOTE
Sections A-D are options for elevator mounting. Select the correct installation method from the available options.
After asssembling the elevator mount, continue to section E.

Assemble the Elevator Mount
8
Assemble the Elevator Mount
Required Parts:
#1 U-Bolt, Round 3/8-16 x 4.68 #2 Clamp, Saddle #3 Bolt, Hex Head, 5/16-18 x
1-1/4”
#8 Locknut, Hex Head, 1/2-13
#9 Washer, Flat, 5/16 #10 Washer, Flat, 1/2 #11 Locknut, Nylon Insert, 5/16 #17 Bracket, Pole
#18 Bracket, Jack Support,
RIGHT
#19 Bracket, Jack Support, LEFT #23 Struts, Board Support #26 Bracket, Angle, RIGHT
#27 Bracket, Angle, LEFT #29 U-Bolt, Square, 1/2-13 x 5 #33 Locknut, Nylon Insert,
3/8-16
#34 Washer, 3/8
WARNING
IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE THE BACKBOARD FOR ANY DAMAGE THAT
MAY HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE. IF
BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE NUMBER: U.S.: 1-800-558-5234;
CANADA: 1-800-284-8339; WWW.SPALDING.COM.
NOTE
Sections A-D are options for elevator mounting.
Poles and mounting locations will vary.
Follow instructions that are packaged with elevator mount for specic assembly details.
A - Completed Elevator Mount to a Square Pole:

Assemble the Elevator Mount
9
B - Completed Elevator Mount to a Round Pole:
C - Completed Elevator Mount to a Wall or Flat Surface:
D - Completed Extension Arm Mounting:

Assemble the Elevator Mount
10
AASSEMBLE THE ELEVATOR MOUNT TO A SQUARE POLE
1. At a position near the ground surface,
assemble pole bracket (17) to square pole
using u-bolts (29), washers (10) and nuts
(8).
#8
#29
#10
#17
2. Attach jack support brackets (18 & 19) to
pole bracket (17) using bolts (3), washers (9)
and nuts (11).
#9
#3
#19
#18
#3
#9
#17
#9
#11

Assemble the Elevator Mount
11
BASSEMBLE THE ELEVATOR MOUNT TO A ROUND POLE
1. At a position near the ground surface,
assemble pole bracket (17) to round pole
using u-bolts (1), clamps (2), washers (34)
and nuts (33) as shown.
#2
#1
#34
#17
#33
2. Attach jack support brackets (18 & 19) to
pole bracket (17) using bolts (3), washers
(9) and nuts (11) as shown.
#9
#3
#19
#18
#3
#9
#17
#9
#11

Assemble the Elevator Mount
12
CASSEMBLE THE ELEVATOR MOUNT TO A WALL OR FLAT SURFACE
1. Secure pole bracket (17) to at solid
surface. Install bolt heads outside for
safety reasons.
#17
Not Included
2. Attach jack support brackets (18 & 19) to
pole bracket (17) using bolts (3), washers
(9) and nuts (11) as shown.
#19
#18
#3
#9
#9
#11
WARNING
A SOLID MOUNTING BASE AND/OR SURFACE, CAPABLE OF WITHSTANDING NORMAL RECREATIONAL USE FORCES, MUST
BE PROVIDED BY THE CUSTOMER. A RELIABLE CARPENTER OR BUILDING CONTRACTOR SHOULD BE CONSULTED IF
THERE ARE QUESTIONS REGARDING THIS PROCEDURE.
CAREFULLY INSPECT MOUNTING AREA FOR STRUCTURAL INTEGRITY AND HIDDEN ELECTRICAL WIRING.
ALL MOUNTING POINTS SHOULD BE SEALED TO PREVENT LEAKS AND WATER DAMAGE.

Assemble the Elevator Mount
13
NOTE
Hardware for these procedures are not included due to various roof and wall construction materials and design structure.
DINSTALL THE ELEVATOR MOUNT TO A FLAT OR ANGLED ROOF
1. Attach struts (23), angle brackets (26 & 27), and jack support brackets (18 & 19) to pole bracket
(17) with bolts (3), washers (9) and nuts (11) as shown.
#9
#9
#3
#18
#11
#19
#23
#23
#27
#26
To U-Channel To Roof
2. Drill holes in roof. Position angled brackets
and secure to roof.
#26 & #27

Assemble the Elevator Mount
14
DINSTALL THE ELEVATOR MOUNT TO A FLAT OR ANGLED ROOF
3. Note position of angle brackets (26 & 27) in relation to pole bracket per style roof.
#26 & #27
#26 & #27
#23
#23
4. Keep assembly upright and position struts
(23) on desired location on roof approx. 26”-
30” (66-76 cm) apart. Level in all directions.
Mark and drill holes. Secure struts in place.. #23
WARNING
USE CAUTION; ASSEMBLY IS HEAVY. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
MINIMUM DISTANCE SHOULD BE 106-3/4” (2.71 M) FROM TOP ELEVATOR HOLE TO PLAYING SURFACE. HOMEOWNER
MUST ASSUME ALL RESPONSIBLILTY FOR ANY PERSONAL OR PROPERTY DAMAGE IF BACKBOARD HEIGHT IS LOWER
THAN RECOMMENDED.
NOTE
To achieve 106-3/4” (2.7 m) you may have to make some adjustments such as moving angled brackets backward or
adding height to the entire assembly with wood between angled brackets and roof.

Assemble the Elevator Structure/Mechanism
15
Assemble the Elevator Structure/Mechanism
Required Parts:
#6 Bolt, Hex Head, 1/2-13 x 7”
Long
#7 Label, Warning #8 Locknut, Hex Head, 1/2-13 #10 Washer, Flat, 1/2
#14 Spacer, 1.8 Long #21 Sleeve, Plastic, Height-
Indicator
#24 Screw Jack Assembly #28 Label, Height-Indicator
#30 Tube, Elevator #31 Spacer, Metal .3.5” Long #32 Washer, Flat, Nylon
Completed Elevator Assembly:

Assemble the Elevator Structure/Mechanism
16
EASSEMBLE THE ELEVATOR
1. Identify the elevator tubes (30).
#30
Toward Mount
Toward board
2. Attach elevator tubes (30) to the jack support brackets (18 & 19) using bolts (6), washers (10),
spacers (31 & 32) and nuts (8) as shown.
#31
#31
#8
#6
#10 #32
#30
#30

Assemble the Elevator Structure/Mechanism
17
EASSEMBLE THE ELEVATOR
3. Attach height decal (28) on screw jack
(24). Align lower edge of decal (28)
with screw jack bottom.
4. Place cover (21) over screw jack (24).
5. Insert spacer (16) into screw jack
assembly (24) as shown.
7
7
9
8
7
9
8
7
#21
#16
1
7
9
8
1
7
9
8
ergrg
#21
#24
#28
6. Install screw jack assembly (24) using bolts (6 & 14), washer (10) and nut (8) as shown.
7
7
9
8
7
9
8
7
7'
2.1m
#8 #8
#30
#14 #14
#30
#6
#10
#10 #8

Assemble the Elevator Structure/Mechanism
18
FATTACH THE WARNING LABEL
1. Adhere the warning label (20) in a clearly
visible place.
7-3/8" High
3-3/4" Wide
PMS 021 for Warning
MUNSELL NOTATION
Hue Value Chroma
5.0 YR 6.0/15
Equiv. CIE Data
(Y%) xy
30.05 0.5510 0.4214
Approx. PMS Color
13 parts yellow
3 parts Warm Red
1/4 part Black
Warning Area = Orange
Size = 3.75" x 7-3/8"
Corner Radius = 3/8"
Die Cut Label
3.25 Mil Vinyl
All Temp. Permanent Adhesive
1 Mil. Polypropolyne Overlaminate
Illustrator CS2 = EPS
Backing + 1/16 Circumference
Rolls of 500
In the U.S.: 1-888-713-5488
In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339
In the U.S.: 1-800-334-9111
#7
REGULATION RIM HEIGHT
IS 10 FEET (3.05 m).
10 ft.
(3.05 m)

Backboard Mounting
19
Backboard Mounting
Required Parts:
#4 Spacer, 1.8 Long #5 Bolt, Hex Head, 1/4-20 x 2-1/4” Long #6 Bolt, Hex Head, 1/2-13 x 7” Long
#8 Locknut, Hex Head, 1/2-13 #13 Nut, Hex, Locking 1/4-20 #15 Spacer, Plastic, 1” Long
#16 Spacer, Metal, .75 O.D., 4” Long #20 Bracket, Elevator #25 Spacer, Plastic, .73 O.D., 1.7” Long
NOTE
Section G-I are options for backboard mounting.
Backboard and frame style will vary.
Follow instructions that are packaged with backboard for specic assembly details.
GATTACH AN H-FRAME STYLE BACKBOARD
1. Attach backboard using hardware
shown.
#16
#16
#8
#8 #6
#6

Backboard Mounting
20
HATTACH A COMPOSITE STYLE BACKBOARD
1. Assemble backboard brackets
(20) using bolt (5) spacer (4)
and nut (13) as shown. #13
#20
#4
#20
#5
2. Attach backboard using
hardware shown.
3. Bend support brackets (20)
to line up with upper holes in
backboard.
#25
#20
#8
#15
#8
#25
#20
#6
#15
#6