SPARTAN sport Magnetic 997 User manual

Magnetic 997
Elliptical Cross Trainer
ITEM NO.: 997N
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo and are subject to change without
prior notice.

1
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 2
PARTS LIST ------------------------------------------------------------------------------- 3
TOOLS -------------------------------------------------------------------------------------- 5
HARDWARE LIST ----------------------------------------------------------------------- 6
EXPLODED VIEW ----------------------------------------------------------------------- 7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
HOW TO MOVE THE ELLIPTICALTRAINER ------------------------------------ 30
OPERATING THE COMPUTER ------------------------------------------------------ 31
ADJUSTMENTS -------------------------------------------------------------------------- 33
MAINTENANCE -------------------------------------------------------------------------- 34
TROUBLESHOOTING ------------------------------------------------------------------ 34
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 35

2
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Be careful when step on or leave the pedal always hold the handlebars first. Make the
pedal at your side at the lowest position, step on the pedal, and stride over the main
frame then step on the other pedal. When using, please hold the handlebar by hands,
make the pedals running smoothly by push or pull handlebars, then run the equipment
regularly by cooperation of hands and feet. After exercise, please also make one
pedal at the lowest position and leave your foot on the higher pedal first and then
another.
7. Do not use the equipment outdoors.
8. This equipment is for household use only. It is not a commercial model.
9. Only one person at a time should use this equipment.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. Care should be taken in mounting or dismounting the equipment.
12. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
13. The maximum weight capacity for this product is 120 kg.
WARNING: Before beginning any exercise program consult your
physician. This is especially important for people who are over 35 years old or who
have pre-existing health problems. Read all instructions before using any fitness
equipment. Do not operate this exercise equipment without properly fitted guards,
as the moving parts can present a risk of serious injury if exposed.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

3
PARTS LIST
No.
Description
Qty
No.
Description
Qty
001
Handrail End Cap Ø32x1.5
2
020
Big Washer Ø6xØ18x1.5
2
002L
Left Handrail Ø32x1.5
1
021
Cross Recessed Pan Head Bolt
M6x15
6
002R
Right Handrail Ø32x1.5
1
022
Hexagon Bolt M6x40
6
003
Handrail Foam Grip
Ø31xØ37x480
2
023L
Left Foot Pedal
1
004
Cross Recessed Pan Head
Tapping Screw ST4.2x12
8
023R
Right Foot Pedal
1
005
Left HandrailArm Cover-A
1
024
Washer Ø6xØ12x1
7
006
Nylon Nut M6
16
025
Hexagon Bolt M8x50
2
007
Curve Washer Ø6xØ12x1
4
026
Powder Metal Bushing
Ø18xØ8x10
4
008
Carriage Bolt M6x35
4
027L
Left Foot Bar 40x25x1.5
1
009
Screw ST4.2x20
18
027R
Right Foot Bar 40x20x1.5
1
010
Left HandrailArm Cover-B
1
028
Washer Ø16xØ8x1.5
2
011
Hexagon Socket Pan Head Cap
Bolt M8x20
4
029
Nylon Nut M8
2
012
Spring Washer Ø8
10
030
Foot Bar Bracket Cover
2
013
Big Washer Ø8xØ25x2
4
031
Handlebar End Cap Ø28.6x1.5
2
014
Washer Ø38x16.5xδ3
4
032
Hand Pulse Sensor with Wire
L=750 mm
2
015
Powder Metal Bushing
Ø38xØ32xØ19x14
8
033
Hexagon Socket Pan Head Cap
Bolt M8x15
8
016L
Left HandrailArm Ø32x1.5
1
034
Curve Washer Ø16xØ8x1.5
2
016R
Right Handrail Arm Ø32x1.5
1
035
Cross Recessed Pan Head
Tapping Screw ST4.2x20
2
017
Powder Metal Bushing
Ø14xØ10x10
4
036
Handlebar Foam Grip
Ø33xØ27x360
2
018L
Front Foot Bar Cover-A
2
037
Handlebar Ø28.6x2
1
018R
Front Foot Bar Cover-B
2
038
Computer HR-1560
1
019
Hexagon Socket Pan Head Cap
Bolt Ø10x46
2
039
Extension Sensor Wire
L=1100 mm
1

4
PARTS LIST
No.
Description
Qty
No.
Description
Qty
040
Cross Recessed Pan Head Bolt
M5x10
4
064
Foot Bar Bracket Ø38x3
2
041
Front Decorative Cover for Front
Post
1
065
Plastic Spacer Ø38xØ19x40
2
042
Rear Decorative Cover for Front
Post
1
066
Crank Disk Ø391x21
2
043
Cross Recessed Pan Head Bolt
M5x55
1
067
Crank 40x20x3
2
044
Curve Washer Ø5xØ19xδ1
1
068
Cross Recessed Pan Head
Tapping Screw ST4.2x15
16
045
Tension Control Knob
1
069
Spring Clip Ø17x1.0
2
046
Tension Cable L=1900 mm
1
070
Wave Washer Ø28xØ17x0.3
1
047
Front Post Ø60x1.5
1
071
Bearing 6003-2Z
2
048
Big Curve Washer Ø8xØ20x2
10
072
Main Frame 80x40x2
1
049
Plastic Bushing Ø32x69
2
073L
Left Plastic Cover
1
050
Right Handrail Arm Cover-A
1
073R
Right Plastic Cover
1
051
Right Handrail Arm Cover-B
1
074
Rubber Cover
2
052
Transport Wheel Ø45x19
2
075
Sensor with Wire L=1600 mm
1
053
Cross Recessed Pan Head Bolt
M6x35
2
076
Cross Recessed Pan Head
Tapping Screw ST2.9x12
2
054
Cap Nut M8
4
077
Hexagon Nut M6
2
055
Adjustable Leveler M10
2
078
Spring Washer Ø6
6
056
Carriage Bolt M8x65
4
079
Tension Bracket 31x30xδ1
2
057
Front Left Stabilizer End Cap
1
080
Eyebolt M6x36
2
058
Front Stabilizer
1
081
Nut M10x1x6
2
059
Front Right Stabilizer End Cap
1
082
Flywheel Ø260
1
060
Cross Recessed Pan Head
Tapping Screw ST4.2x25
11
083
Cross Recessed Pan Head Bolt
M6x10
1
061
Plastic Disc Cap
2
084
Bearing 6000-2Z
2
062
Nut M10x1.25x6
2
085
Washer Ø10xØ14x1
2
063L
Left Cover
1
086
Hexagon Socket Pan Head Cap
Bolt M8x25
1
063R
Right Cover
1
087
Idler Arm
1

5
PARTS LIST
TOOLS
No.
Description
Qty
No.
Description
Qty
088
Hexagon Socket Pan Head Cap
Bolt M8x10
1
092
Rear Left Stabilizer End Cap
1
089
Belt Pulley Ø260
1
093
Rear Stabilizer 55x50x1.5
1
090
Belt PJ400
1
094
Rear Right Stabilizer End Cap
1
091
Plastic Screw Anchor Ø8x32
1
095
Hexagon Nut M10
2
Multi Hex Tool with Phillips Screwdriver
1 PC
Allen Wrench
1 PC

6
HARDWARE LIST
(4) Cross Recessed Pan
Head Tapping Screw
8 PCS
(6) Nylon Nut
4 PCS
(7) Curve Washer
4 PCS
(8) Carriage Bolt
4 PCS
(6) Nylon Nut
6 PCS
(24) Washer
6 PCS
(22) Hexagon Bolt
6 PCS
(54) Cap Nut
4 PCS
(48) Big Curve Washer
4 PCS
(56) Carriage Bolt
4 PCS

7
EXPLODED VIEW

8
ASSEMBLY INSTRUCTIONS
STEP 1
Position the Front Stabilizer (58) in front of the Main Frame (72) and align bolt holes.
Attach the Front Stabilizer (58) onto the front curve of the Main Frame (72) with two Carriage
Bolts (56), two Big Curve Washers (48), and two Cap Nuts (54). Tighten cap nuts with the
Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
(54) Cap Nut
2 PCS
(48) Big Curve Washer
2 PCS
(56) Carriage Bolt
2 PCS

9
STEP 2
Position the Rear Stabilizer (93) behind the Main Frame (72) and align bolt holes.
Attach the Rear Stabilizer (93) onto the rear curve of the Main Frame (72) with two Carriage
Bolts (56), two Big Curve Washers (48), and two Cap Nuts (54). Tighten cap nuts with the
Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
(54) Cap Nut
2 PCS
(48) Big Curve Washer
2 PCS
(56) Carriage Bolt
2 PCS

10
STEP 3
Remove six Hexagon Socket Pan Head Cap Bolts (33), six Spring Washers (12), and six Big
Curve Washers (48) from the Main Frame (72). Remove bolts with theAllen Wrench
provided.

11
STEP 4
It is recommended to have a second person assist with this step. One person should hold
the Front Post (47) in place while the other person to connect the wires.
Insert the Tension Cable (46) through into the bottom hole of the Front Post (47) and pull it
out from the square hole of the Front Post (47).
Connect the Sensor Wire (75) from the Main Frame (72) to the Extension Sensor Wire (39)
from the Front Post (47).

12
STEP 5
Insert the Front Post (47) onto the tube of the Main Frame (72) and secure with six Hexagon
Socket Pan Head Cap Bolts (33), six Spring Washers (12), and six Big Curve Washers (48)
that were removed. Tighten bolts with the Allen Wrench provided.
STEP 6
Remove one Cross Recessed Pan Head Bolt (43) and one Curve Washer (44) from the
Tension Control Knob (45). Remove bolt with the Multi Hex Tool with Phillips Screwdriver
provided.

13
STEP 7
Put the cable end of resistance cable of Tension Control Knob (45) into the cable lock of
Tension Cable (46), see Figure A.
Pull the resistance cable of Tension Control Knob (45) up and force it into the slot of metal
bracket of Tension Cable (46), see Figure B.
Insert the metal fitting on the resistance cable of Tension Control Knob (45) into the hole at
the end of the slot in the metal bracket of Tension Cable (46), see Figure C.
Connect the resistance cable of Tension Control Knob (45) to Tension Cable (46) complete,
see Figure D.
Attach the Tension Control Knob (45) onto the Front Post (47) with one Cross Recessed Pan
Head Bolt (43) and one Curve Washer (44) that were removed. Tighten bolt with the Multi
Hex Tool with Phillips Screwdriver provided.

14
STEP 8
Attach the Left Foot Pedal (23L) onto the Left Foot Bar (27L) with three Hexagon Bolts (22),
three Washers (24), and three Nylon Nuts (6). Tighten the nylon nuts with the Multi Hex
Tool with Phillips Screwdriver provided.
Hardware:
(6) Nylon Nut
3 PCS
(24) Washer
3 PCS
(22) Hexagon Bolt
3 PCS

15
STEP 9
Attach the Right Foot Pedal (23R) onto the Right Foot Bar (27R) with three Hexagon Bolts
(22), three Washers (24), and three Nylon Nuts (6). Tighten the nylon nuts with the Multi
Hex Tool with Phillips Screwdriver provided.
Hardware:
(6) Nylon Nut
3 PCS
(24) Washer
3 PCS
(22) Hexagon Bolt
3 PCS

16
STEP 10
Remove two Hexagon Socket Pan Head Cap Bolts (11), two Spring Washers (12), two Big
Washers (13), and two Washers (14) from the right horizontal axis of the Front Post (47) and
left Crank (67). Remove bolts with the Allen Wrench provided.

17
STEP 11
Attach the Left Handrail Arm (16L) onto the left horizontal axis of the Front Post (11) and the
Foot Bar Bracket (64) onto the left Crank (67) with two Hexagon Socket Pan Head Cap Bolts
(11), two Spring Washers (12), two Big Washers (13), and two Washers (14) that were
removed. Tighten bolts with the Allen Wrench provided.

18
STEP 12
Remove two Hexagon Socket Pan Head Cap Bolts (11), two Spring Washers (12), two Big
Washers (13), and two Washers (14) from the left horizontal axis of the Front Post (47) and
right Crank (67). Remove bolts with the Allen Wrench provided.

19
STEP 13
Attach the Right Handrail Arm (16R) onto the right horizontal axis of the Front Post (11) and
the Foot Bar Bracket (64) onto the right Crank (67) with two Hexagon Socket Pan Head Cap
Bolts (11), two Spring Washers (12), two Big Washers (13), and two Washers (14) that were
removed. Tighten bolts with the Allen Wrench provided.