Deltech Fitness DF9800 User manual

DF9800
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
FLAT/INCLINE/DECLINE BENCH
Assembly Manual
Assembly Video Available
Simply scan the QR code below
on your phone’s camera to access

BOX CONTENTS
FRONT FOOT
QTY 1
A
REAR FOOT
QTY 1
B
FRAME
QTY 1
C
LEG HOLDDOWN
TUBE
QTY 1
E
SEAT ADJUSTMENT
BASE
QTY 1
G
TELESCOPING
TUBE
QTY 1
H
ADJUSTMENT SUPPORT
QTY 1
D
BACKREST MOUNT
QTY 1
F

CLAMP PLATE
QTY 2
M
SEAT PAD
QTY 1
O
ADJUSTMENT FLANGE
QTY 2
N
BOX CONTENTS
ROLLER TUBE
QTY 1
K
BACKREST PAD
QTY 1
P
ROLLER PADS
QTY 2
Q
J
RIGHT HAND
SEAT FLANGE
QTY 1
J
LEFT HAND
SEAT FLANGE
QTY 1
I

HARDWARE
M12 x 75MM BOLT
QTY 7
DD
M12 WASHER
QTY 24
BB
M8 WASHER
QTY 10
GG
M12 NUT
QTY 12
CC
M8 x 25 MM BOLT
QTY 10
FF
M12 x 150MM BOLT
QTY 1
AA
RUBBER SHOE
QTY 4
HH
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
MUSHROOM CAP
QTY 2
I I
M12 x 90MM BOLT
QTY 4
EE

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE RISK OF INJURY CAN BE REDUCED BY ALWAYS FOLLOWING
THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ACCESSORIES ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE
B
F
H
H
J

START BY INSTALLING RUBBER SHOES “HH” OVER REAR FOOT “B” AND FRONT
FOOT “A”.
ATTACH REAR FOOT “B” TO FRAME “C” USING M12 x 75MM BOLTS “DD”, M12
WASHERS “BB”, CLAMP PLATE “M”, AND M12 LOCKNUTS “CC”.
ATTACH FRONT FOOT “A” TO FRAME “C” USING M12 x 75MM BOLTS “DD”, M12
WASHERS “BB”, CLAMP PLATE “M”, AND M12 LOCKNUTS “CC”.
DO NOT TIGHTEN NUTS AT THIS TIME.
FRAME ASSEMBLY
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS BENCH ARE
LOCK NUTS, THIS MEANS YOU MUST
TIGHTEN THEM DOWN PAST THE PLASTIC
INSERT.) PLEASE SEE BACK PAGE FOR
MORE INFORMATION
HH
B
A
C
M
DD
CC
BB
BB
HH
DD
BB
BB
CC
M
HH
HH
MAKE SURE THAT
WHEEL FLANGES ARE
FACING AS SHOWN

INSTALL ADJUSTMENT FLANGES “N” TO FRAME USING M12 x 75MM BOLTS “DD”,
M12 WASHERS “BB”, AND M12 LOCK NUTS “CC”.
DO NOT TIGHTEN NUTS AT THIS TIME.
ADJUSTMENT FLANGE INSTALLATION
N
DD
BB
BB
CC
MAKE SURE LARGER
RADIUS IS ON THE TOP

BACKREST FRAME ASSEMBLY
BB
AA
BB
CC
F
D
INSTALL ADJUSTMENT SUPPORT “D” TO BACKREST MOUNT “F’ USING
M12 x 150MM BOLT “AA”, M12 WASHERS “BB”, AND M12 LOCK NUT “CC”.
DO NOT TIGHTEN NUT AT THIS TIME.

INSTALL BACKREST FRAME ASSEMBLY AND LEFT AND RIGHT HAND SEAT
FLANGES “I” AND “J” TO FRAME USING M12 x 90MM BOLT “EE”, M12 WASHERS
“BB”, AND M12 LOCK NUTS “CC”.
DO NOT TIGHTEN NUT AT THIS TIME.
BACKREST FRAME & SEAT FLANGE INSTALLATION
BB
J
I
BB
EE
CC

TELESCOPING TUBE ASSEMBLY
SLIDE TELESCOPING TUBE “H” INTO THE SEAT ADJUSTMENT BASE “G”.
(YOU WILL NEED TO LOOSEN BOLT TO ALLOW TELESCOPING TUBE TO
SLIDE IN. AFTER TELESCOPING TUBE IS INSTALLED, RETIGHTEN BOLT.)
H
G
YOU WILL NEED TO
LOOSEN THIS BOLT TO
ALLOW TELESCOPING
TUBE TO SLIDE IN