SPE DFG700-1 User manual

DFG700-1
Diamond Floor Grinder
Operating Manual
This manual is provided to persons purchasing an
SPE machine and may not be reproduced in part or full
without written permission of
SPE International Ltd.
This manual provides the basic information required
and is only to be used as a guideline.
The SPE machines are manufactured and covered by
SPE design registrations granted and pending.
SPE International Ltd reserves the right to alter the
equipment design and specification as required
without notice.
The SPE product range is subject to amendment and
improvement as a result of on going research
Honeyholes Lane, Dunholme, Lincoln LN2 3SU, England
Tel: [phone] Fax: [phone]
Email: [e-mail]

DFG700 - 1
Operating Manual
DFG700 Triple Head
Diamond Floor Grinder
OPERATING MANUAL
This manual covers to the best of our knowledge the operation and maintenance of the
DFG 700 - 1 diamond floor grinder. Before operation of the equipment the manual should be
read and understood by the operator. The safety regulations must be followed at all times.
Service of electrical components should be carried out by authorised personnel.
WARNING
Failure to follow these instructions may result in serious personal injury or death. SPE disclaims
all responsibility for damage to persons or objects arising as a consequence of incorrect
handling of the machine and failure to inspect the machine for damage or other faults that may
influence the operation prior to starting work.

DFG700 - 1
Operating Manual
INDEX
Page No
1 Starting Work
2 Fitting Grinding Plates
Metal Tools
Resin Tools
Diamond Plates
Wet Grinding/Polishing
3 Maintenance
4 Safety
5 - 10 Accessories
11 Spare Parts Breakdown
12 Head Drive Components
13 Grinding Head
14 Utility Components
15 Drive Components
16 Frame Components
17 Wiring Diagram
18 Electrical Components
19 Specifications
20 Warranty
21 Declaration of Conformity
22 Conditions of Sale

DFG700 - 1
Operating Manual
STARTING WORK
1. BEFORE STARTING WORK ENSURE THAT THE GRINDING HEADS HAVE BEEN
FITTED, SEE PAGE 2
2. Ensure the power supply is correct.DFG 700-1 - This should be a 380/415v 32 amp
supply from the mains or generated with a minimum of 20 kva on 50 cycles. The plug on the
DFG700 machine is a 380/415v 32 amp 5 pin red plug.
3. Connect a vacuum hose or a water supply to control the dust. WARNING – DO NOT
ALLOW WATER TO MAKE CONTACT WITH ANY ELECTRICAL COMPONENTS.
4. Select the number of pivotal weights required for the process and position forward over
the grinding head, ensuring the locking pins are secured.
5. After connecting the machine to the power supply turn the red isolator switch to the ON
position. The red light will illuminate on the electric panel. Note: the DFG700 is fitted with an
automatic phase correction system. This ensures the operator does not need to worry about
the power supply being phased to suit the machine.
6. Turn the speed control knob on top of the electrical panel to between 1-2 speed setting.
7. Press the green button on top of the electrical panel. The green light will illuminate and
the inverter is now powered up.
8. Turn on the vacuum or water supply.
9. Pull the dead man handle in, on the left handle bar, and press the green button on the
right handle bar. The machine will now start to grind the floor.
10. To increase the grinding speed, turn the speed control knob on top of the electrical
panel to the next level. With experience the operator will be able to feel the correct speed
setting for the grinding process.
11. To stop the machine, release the dead man handle on the left handle bar.
Please note that if the isolator switch or red stop button is turned off, then
immediately back on again, the inverter will not start with the green button on top of
the panel for 3 minutes.
1

DFG700 - 1
Operating Manual
FITTING GRINDING PLATES
1. Disconnect from the power supply.
2. Tip the DFG700 backwards on to its support bars. The machine must be secured and
supported.
METAL GRINDING TOOLS
1. Fit the required metal tools to the 6451 drive plate and ensure M6 allen screws are
securely tightened.
2. Place the drive plate onto the DFG700 machine and turn anti-clockwise into the locked
position.
3. Fit the other two drive plates as above.
4. Lower the machine back onto the floor surface.
RESIN GRINDING TOOLS
1. Fit the required resin tool to the 6450. They fit on with a velcro system.
2. Place the drive plate onto the DFG700 machine and turn anti-clockwise into the locked
position.
3. Fit the other two drive plates as above.
4. Lower the machine back onto the floor surface
DIAMOND GRINDING PLATES
It is possible to use the conventional DFG bolt on diamond plates with the DFG700. To fit
this type of plate the 3no standard coupling plate part number 7337B, bolted to the flexible
coupling must be removed and replaced with 3no 5064A adaptor plates.
1. Fit the diamond plate to the adaptor plate (5064A).
2. Ensure the grinding plate is seated to the adaptor plate correctly prior to inserting and
tightening the 4no counter sunk screws diagonally to a maximum torque of 75NM.
3. Fit the other two grinding plates as above.
4. Lower the machine back onto the floor surface.
WET GRINDING/POLISHING
The DFG700 accessories can be used wet or dry however should water be required fill water
tank to required level. Open the tap beneath the tank and water will be fed on to the grinding
heads.
NOTE – ALWAYS USE THE SAME TYPE AND BOND OF TOOL ON EACH OF THE THREE
HEADS. EQUALLY WORN TOOLS MUST BE FITTED AS A SET.
TO ENSURE THE CORRECT TOOL IS BEING USED CHECK WEAR RATES AFTER QUARTER
OF AN HOUR AND AGAIN AT HALF HOURLY INTERVALS, THIS WILL GIVE AN INDICATION OF
TOTAL WEAR RATES AND COST PER M
2

DFG700 - 1
Operating Manual
MAINTENANCE
AFTER USE:
 Clean the machine to remove all build up of dust and surface residue. If using a hose pipe or
pressure washer take care that water is not directed onto electrical components and switches.
(Note: Motors and switches are not waterproof)
Clean the filter at the bottom of the electric panel. Remove and blow out any dust. Replace
with a new filter if damaged. See Fig 1
 The drive belts will give a long and trouble free operating life if basic procedures are followed.
To inspect remove the belt guard. The drive belts are tensioned by sliding the tension pulley
along the adjusting slot allowing 10mm belt deflection. See Fig 2. It is important that the drive
belts are not over tensioned. Serious damage could be caused to the drive shaft, drive shaft
bearings and drive motor if the belts are excessively tight.
 Periodically check the oil level in the drive gearbox (part no 7309) either through the sight level
gauge or level plug depending on the model. See Fig 3. If oil comes out the inspection hole
when level plug is removed the gearbox contains sufficient oil. If oil level is low top up to just
above the main gear by removing the gearbox oil filler plug. See Fig 4. Access to the oil filler
plug is gained by removing the drive motor and motor mount plate. If any oil is required, use an
‘SY320’ grade gear oil.
Fig 1 - Electric Fig 2 - Belt Tension Fig 3 - Oil Level Plug Fig 4 – Gearbox Oil
Panel Filter Pulley or Level Gauge site Filler Plug
The planetary gear case is sealed and should not require any maintenance. The internal gears
are lubricated with lithium EPO grease.
 All components should be checked daily for tightness and the drive belts for tension weekly.
 The flexible drive couplings that support the grinding heads should be checked on a weekly
basis, the couplings should be firm without excessive movement.
 Any excess vibration due to uneven plate wear should result in the grinding plates being
changed to eliminate damage to couplings and bearing assembly support units.
3

DFG700 - 1
Operating Manual
SAFETY
Only trained operatives should be allowed to work the DFG700 range of floor grinders.
Note: It is possible that the noise level produced by the Diamond Floor Grinder could exceed
90dbA. Appropriate PPE must be worn and the equipment must be used in line with
guidelines laid down by the Health & Safety Executive.
Always ensure that all power leads and hoses are disconnected before attempting to service
the machine. Never tip the machine backwards until the grinding plates have stopped
rotating and the machine has been isolated at the main supply.
Noise and vibration will occur at various levels dependent on the grinding attachments and work
being completed. It is recommended that tests are taken on site to provide the operator with
accurate information on using the equipment within the guidelines laid down by the Health &
Safety Executive.
NOTE:
1. NEVER OPERATE THE DFG700 FLOOR GRINDER WITHOUT THE BELT GUARDS FITTED
2. NEVER OPERATE THE DFG700 FLOOR GRINDER OUTDOORS IN WET CONDITIONS AS
THE ELECTRICAL COMPONENTS ARE NOT WATERPROOF
3. NEVER OPERATE THE DFG700 WITH THE HEADS RAISED FROM THE FLOOR
4

DFG700 - 1
Operating Manual
Part No
Description
Application
6450
Resin Tool Drive Plate
Quick release drive plate with Velcro for
the fitment of resin tools.
Can be used wet or dry.
6460
Combination
Resin / Metal Tool
80 Grit Orange
Mixed bond ensures a very fine scratch
profile for use after metal bond or
directly onto power floated concrete
leaves perfect surface for thin film
coatings or polishing with a minimum
number of stages.
Can be used wet or dry.
6461
Resin Tool
100 Grit Black
For the first stage of resin polishing
leaves a matt finish.
Can be used wet or dry.
6462
Resin Tool
200 Grit Blue
For the second stage of resin polishing
leaves a closed matt finish.
Can be used wet or dry.
6463
Resin Tool
400 Grit Red
For the third stage of resin polishing
leaves a honed silk finish.
Can be used wet or dry
6464
Resin Tool
800 Grit White
For the forth stage of resin polishing
leaves a light reflective finish suitable for
most industrial and commercial
applications.
Can be used wet or dry
5

DFG700 - 1
Operating Manual
Part No
Description
Application
6465
Resin Tool
1500 Grit Yellow
For the final stage of resin polishing
leaves a clear reflective shine ideal for
decorative surfaces.
Can be used wet or dry.
6451
Metal Tool Drive Plate
Quick release drive plate for the bolt on
fitment of metal tools.
Can be used wet or dry.
6470
Metal Tool
16 Grit Hard Bond
For initial smoothing of rough surfaces,
coating and adhesive removal from soft
concrete.
Can be used wet or dry.
6471
Metal Tool
120 Grit Hard Bond
First Stage Tool for grinding / polishing
soft concrete.
Can be used wet or dry.
6472
Metal Tool
80 Grit Hard Bond
Second Stage Tool for grinding /
polishing soft concrete.
Can be used wet or dry.
6473
Metal Tool
120 Grit Hard Bond
Third Stage Tool for grinding / polishing
soft concrete.
Can be used wet or dry.
6

DFG700 - 1
Operating Manual
Part No
Description
Application
6474
Metal Tool
16 Grit Medium Bond
For initial smoothing of rough surfaces,
coating and adhesive removal.
Can be used wet or dry.
6475
Metal Tool
30 Grit Medium Bond
First Stage Tool for grinding /
polishing concrete and
seamless terrazzo.
Can be used wet or dry.
6476
Metal Tool
80 Grit Medium Bond
Second Stage Tool for grinding /
polishing concrete and
seamless terrazzo.
Can be used wet or dry.
6477
Metal Tool
120 Grit Medium Bond
Third Stage Tool for grinding /
polishing concrete and
seamless terrazzo.
Can be used wet or dry.
6478
Metal Tool
16 Grit Soft Bond
For initial smoothing of hard rough
surfaces, coating and adhesive
removal from hard dense concrete.
Can be used wet or dry.
6479
Metal Tool
30 Grit Soft Bond
First Stage Tool for grinding /
polishing hard dense concrete.
Can be used wet or dry.
7

DFG700 - 1
Operating Manual
Part No
Description
Application
6480
Metal Tool
80 Grit Soft Bond
Second Stage Tool for grinding /
polishing hard dense concrete.
Can be used wet or dry.
6481
Metal Tool
120 Grit Soft Bond
Third Stage Tool for grinding /
polishing hard dense concrete.
Can be used wet or dry.
6486
Green PCD Tool
1 Segment Anti-clockwise
For the rapid removal of adhesive,
coatings and failed latex
from a hard substrate.
6488
Green PCD Tool
2 Segment Anti-clockwise
For the rapid removal of adhesive,
coatings and failed latex
from a hard substrate.
6498
Blue PCD Tool
1 Segment Clockwise
For the rapid removal of adhesive,
coatings and failed latex
from a hard substrate.
6499
Blue PCD Tool
2 Segment Clockwise
For the rapid removal of adhesive,
coatings and failed latex
from a hard substrate.
8

DFG700 - 1
Operating Manual
Part No
Description
Application
5064A
DFG700 250mm
Adapter Plate
Allows conventional 250mm segmented
diamond grinding plates to be fitted.
6401
10 Segment Blue, 250mm
Diamond Plate
10 Segments, 10mm segment depth.
Economical grinding of concrete
and adhesive.
Can be used wet or dry.
6402
10 Segment Red, 250mm
Diamond Plate
10 Segments, 10mm segment depth.
Removal of coatings and S/L.
Coarse diamond grit.
Can be used wet or dry.
6403
16 Segment Blue, 250mm
Diamond Plate
16 Segments, 10m segment depth.
Grinding of concrete in preparation
for following on coatings.
Excellent cost per square metre.
Can be used wet or dry.
6403A
16 Segment Black, 250mm
Diamond Plate
16 Segments, 10mm segment depth.
Hard bond for softer surfaces.
Grinding of concrete in preparation
for following on coatings.
Excellent cost per square metre.
Can be used wet or dry.
6403B
16 Segment Grey, 250mm
Diamond Plate
16 Segments, 10mm segment depth.
Soft bond for hard surfaces.
Grinding of concrete in preparation
for following on coatings.
Excellent cost per square metre.
Can be used wet or dry.
9

DFG700 - 1
Operating Manual
Part No
Description
Application
6403C
16 Segment Purple, 250mm
Diamond Plate
16 Segments, 10mm segment depth.
Soft bond for hard surfaces.
Second stage grinding of terrazzo
and decorative concrete.
Leaves a smooth flat finish.
6403Y
16 Segment Yellow, 250mm
Diamond Plate
16 Segments, 10mm segment depth.
Economical grinding of concrete in
preparation for following on coatings.
Excellent cost per square metre.
Can be used wet or dry
6404
20 Segment Blue, 250mm
Premium Diamond Plate
20 Segments, 10mm segment depth.
Premium plate for concrete grinding,
paint removal, 1st stage grinding of
resin based terrazzo.
Can be used wet or dry.
6405
16 Segment Button Head,
250mm Premium
Diamond Plate
For the removal of thicker adhesive,
on sand / cement screed whether
open or closed. Will cope with large
volume areas in a cost effective
manner. To be used with softer
elastomeric and thin film coatings
10

DFG700 - 1
Operating Manual
11