Speco HINT13D7G User manual

Please read this manual thoroughly before operation and keep
it handy for further reference.
HINT13D7G (3.6mm)
650Line Intensifier3
TM
Tamperproof Dome
Vandal Resistant
w/Chameleon Cover
Wall/Ceiling Mount

DO NOT use power sources other than that specified.______
The lighting flash with an arrowhead symbol, within an equilateral triangle is
Intended to alert the user to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons____________________________________
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (serving) instructions
in the literature accompanying the appliance__________________
INFORMATION -This equipment has been tested and found to company with
limits for a class a digital device Pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
Interference W hen the equipments operated in a commercial environment.
This equipment generates, uses, and Can Radiate radio frequency energy and
if not installed and used in accordance with the instruction manual, may Cause
Harmful interference to radio communications. Operation of this equipment in a
r e s i d e n t i a l a r e a is l i k e l y to c a u s e h a r m f u l i n t e r f e r e n c e in w h i c h
Case the user will be required to correct the interference at his own expense.
WARNING –Change or modification not expressly approved by the manufacturer could void
the user’s authority to operate the equipment__________________________________
CAUTION : To prevent electric shock and risk of fire hazards.
DO NOT expose this appliance to rain or moisture.000
This installation should be made by a qualified service person and should conform to all local codes.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR B ACK).
NO USER SERVICEABLE PARTS INSIDE
R E F E R S E R V I C I N G TO Q U A L I F I E D
SERVICE PERSONNEL._______________
CAUTION
WARNING & CAUTION
2

PACKAGE CONTENTS
3
Please make sure that the following items are included
in the Package:
-3 Mounting Screws and Anchors
-1 Set Screw
-1 Wrench
-1 Video Test Connector
-1 Power Cable
-1 Chameleon Cover

CAMERA INSTALLATION
4
* Spray the color of your choice onto the Chameleon cover
* If necessary, apply a second coat
* Painting method for the Chameleon Dome
Place the Chameleon Dome over the camera and push until it snaps
into position.
●Notes : Optional painting before installation
CHAMELEON COVER

FEATURES
5
More Powerful Performance in low light condition.
High quality Pictures to be captured in very low light condition.
INTENSIFIER 3
Horizontal resolution of 650 TV lines is achieved by using a
SONY Super-HAD CCD with 410,000 pixels, and a custom DSP
yielding pictures with a high S/N ratio.
650TVL Resolution
The Intensifier camera has a DSP chip that can remove image
noise efficiently showing clean images in low light conditions.
SPECO DNR
PRESETS (Outdoor, Indoor, Elevator, Lobby, Hallway & Low Light)
Used for a quick and easy setup for the installation environment.
Now with “PRESETS”
More Powerful WDR in strong back lighting.
Your camera allows you to get a clear image.
WDR
This function reverses bright spots in the picture (such as
headlights).This enables the entire system to do a better job of
resolving and displaying grayscale information such as a
license plate.
HLC (High Light Compensation)

FEATURES
6
This function removes image jitter that is caused by vibration.
STABILIZER
All camera functions are menu driven for ease of programming.
OSD
It also has the ability to mask up to 8 areas of the image.
Each zone can be independently programmed via the OSD.
PRIVACY MASK
The Intensifier camera can show color images in all lighting
conditions or the camera may automatically switch to a B/W
mode in low light conditions
DAY/NIGHT
DIGITAL ZOOM
Additional Zoom capability beyond the analog.

OSD MENU TREE
7
EXIT
CAM NAME
LENS
DC IRIS / MANUAL
INTENSIFIER
AGC / SHUTTER / INTENSIFY / INITIAL SET / PREVIOUS
DAY / NIGHT
WDR / BLC / HLC
SPECO DNR
COLOR TEMP
EFFECTS
SPECIAL
ADVANCED MENU
PRESETS
INDOOR / OUTDOOR / LOW LIGHT / LOBBY / HALLWAY / ELEVATOR
ADVANCED
EXIT
MAIN MENU
AUTO / DAY / NIGHT / EXT
AWC-SET / MANUAL / ATW1 / ATW2
DZOOM / IMAGE FREEZE / D-EFFECT / CONTRAST / SHARPNESS /
COLOR ADJUST / INITIAL SET / PREVIOUS
MOTION DET / PRIVACY MASK / LANGUAGE / STABILIZER / LL SYNC /
MONITOR TYPE / FACTORY RESET / PREVIOUS
DNR LEVEL / SSC (Speco Sensitivity Control)

OSD MENU DETAILS
8
1. PRESET
[INDOOR / OUTDOOR / LOW LIGHT / LOBBY / HALLWAY / ELEVATOR]
Quick & Easy Way to install without complicated OSD menu setting!
** Attention : Select any preset mode and push the set button once,
Blinking status means it is correctly set up at that mode.
* * If you need more detailed setting, click ‘ADVANCED’ to see more
OSD menu at every preset mode.
2. INTENSIFIER
[AGC / SHUTTER / INTENSIFY / INITIAL SET / PREVIOUS]
- AGC (Off / Low / Middle / High)
: Adjusts value of AGC gain.
-SHUTTER
* FLK - Flicker-less mode (FLK) reduces on-screen flickering.
* ESC - Electronic Shutter Control (AUTO) adjusts electronic shutter F
stop.
- INTENSIFIER: Automatically provides a clear image under low-
light conditions. You can control the maximum low-light magnification
from 2x to 512x (increasing magnification may cause noise/distortion).
This function is deactivated when SHUTTER is set to FLK mode.

OSD MENU DETAILS
9
4. WDR / BLC / HLC
- WDR
: Provides light level control to overcome severe back light conditions.
- HLC (High Light Compensation)
: High Light Compensation removes the bright light conditions.
3. DAY/NIGHT
[AUTO / DAY / NIGHT]
- DAY : Full time color mode
- NIGHT : Full time black & white mode
- AUTO (D/N LEVEL / DWELL TIME / NIGHT BURST)
** Attention : AUTO is disabled when the AGC in INTENSIFIER is ‘Off’.
5. COLOR TEMP
[AWC SET / MANUAL / ATW1 / ATW2]
- AWC SET
: Set while pointing the camera towards a sheet of white paper.
- MANUAL
: This setting allows for increasing or decreasing the red or blue factor
on screen.
Set the ATW1 before you adjust the manual settings.
- ATW 1
: Select Auto Tracking White Balance (ATW) when the color temperature
is 2400°K~10500°K.
- ATW 2
: Adjust to reduce color shifting.
** Attention : White Balance may not work properly when in special
light condition such as clear sky, sunset, dim lighting, mixed
lights providing different temp. etc.

OSD MENU DETAILS
10
7. EFFECTS
[DZOOM / IMAGE FREEZE / D-EFFECT / CONTRAST / SHARPNESS /
COLOR ADJUST / INITIAL SET / PREVIOUS]
-DZOOM : Digital Zoom. Select this and set a desired zoom level to
obtain an extended focal length.
-IMAGE FREEZE : Freezes the display image.
-D-EFFECT : Change the video direction. Vertical Flip, Mirror, and
Rotate
-CONTRAST : Adjusts contrast Levels.
-SHARPNESS : Adjusts Sharpness Level.
-COLOR ADJUST : Adjust various color options for the camera
(Color toggle, Color Level, Color Hue, Red Gain, Blue Gain)
-INITIAL SET : Return to the default setting defined in the "EFFECT"
menu.
6. SPECO DNR
- Reduces noise/distortion on the screen.
Increasing the DNR level reduces noise
but may introduce video artifacts.
DNR is deactivated if AGC is turned off.
** SSC (Speco Sensitivity Control)
- adjusts the brightness level in low light
conditions only. Adjust this setting to
achieve a good image in low light.

OSD MENU DETAILS
11
8. SPECIAL
[MOTION DET / PRIVACY MASK / LANGUAGE / STABILIZER / LL SYNC
/ MONITOR TYPE / FACTORY RESET / PREVIOUS]
- MOTION DET.
: Built in motion detector with adjustable areas of coverage. A motion
trigger will send a signal to an external alarm device when motion
is detected.
* Zone Number: Select MD area to activate: 8 Areas can be selected.
* Zone Stat: Determine MD area selected.
* Width / Height: Set the size of MD
* Move X/Y: Set the coordinate for the MD position.
* Sensitivity: 8 levels. When sensitivity number is high, motion detection
sensitivity is increased.
- PRIVACY MASK
Mask up to 8 areas of the screen from video monitoring.
* Mask Number: Select PM area to activate. 8 Areas can be selected.
* Mask Stat: Determine PM area selected.
* Mask Color: Determine area color. Grey, White, Red, Green, Blue,
Yellow, Black colors are available.
* Width / Height: Set the size of PM
* Move X/Y: Set the coordinate of the PM position.
-LANGUAGE
: ENGLISH / RUSSIAN / SPANISH / FRENCH / POLISH / GERMAN
-STABILIZER
: Stabilizes the image that may be subject to vibration.
LL SYNC : Synchronizes the phase of multiple cameras that are operating
with AC power.
* INT : Internal Synchronization
* L/L : Power Synchronization type, Line-Lock
*Remark : Whenusing DC12V, SYNC menu is fixed to INT mode.
When using AC24V, the L/L is available.
- MONITOR TYPE
: LCD/ CRT monitor type is selectable.

Item HINT13D7G
Power Source 12VDC & 24VAC ( Dual Voltage )
Power Consumption 130mA (DC) / 1.8W (AC)
Image Sensor 1/3”, SONY SUPER HAD II CCD, 410,000 pixels
Total Pixels 811(H) x 508(V) , 1/3” CCD
Effective Pixels 768(H) x 494(V) , 1/3” CCD
Lens Type 3.6mm
Maximum Aperture Ratio 1 : 1.3 ~2.0
Scanning System 2 : 1 Interlaced 525 Lines / 60 Fields / 30 Frames
Synchronization Internal / Line-Lock
Video Output 1.0V [p-p] Composite, 75Ω
Resolution 650 TV Line
Gain Control Low / Middle / High / OFF selectable
Electric Shutter Speed 1/60 ~ 1/90,000 sec
INTENSIFIER 3 Built-in ( selectable limit ~ X512)
COLOR TEMP (White
Balance) ATW 1 / ATW 2 / AWC SET / MANUAL
Min. Illumination 0.00002Lux (intensifier) 0.03Lux (shutter)
S/N ( Y signal) 52dB (Weight On)
SPECO DNR ON - DYNAMIC / OFF
Motion Detection ON / OFF (8 Programmable Zone)
OSD Built - in
Privacy Function ON / OFF (8 Programmable Zone)
Operational Temperature -29℃~ +50℃( - 20℉~122℉)
Operational Humidity 30% ~90% RH
Weight 1.54Ibs
SPECIFICATIONS
12

DIMENSIONS
* SIDE VIEW
* TOP VIEW
27
DIA 80
DIA 110
78
HIGH IMPACT DOME
13

WARRANTY
14

MEMO

200 New Highway
Amityville, NY 11701
631-957-8700
www.specotech.com
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice
and without incurring any obligation.
Rev. 120719