Speco VLD9 User manual

USER MANUAL
Thank you for purchasing our product. Speco Technologies is constantly developing and
improving products. We reserve the right to modify product design and specifications
without notice and without incurring any obligation.
VLD9 /VLD9M

1
Warnings
■ If the product does not work properly, please contact the dealer or where the product was purchased.
Speco Technologies is not responsible for any problems caused by improper operation or repair.
■ Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity
during transportation, storage, and/or installation.
■ Do not install near sources of heat.
■ Only install the product in environments inside the specification operating temperature and humidity
range.
■ Do not install the camera near power lines, radar equipment or other electromagnetic radiation.
■ Do not block any ventilation openings if any.
■ Use all the weatherproofing hardware requirement to minimize weather intrusion.
This camera series is the latest technology and advanced circuit design, which features high definition and
sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable,
ensuring the requirement of the HD monitoring in the traditional surveillance system.
Introduction
● High Resolution
Adopt high performance sensor, providing high definition and clear image.
● High Transmission Performance
Real-time transmission with high speed and long distance.
● DNR
Reduce noise from brightness and color signal.
● OSD
Access the camera settings which can be clearly displayed through the main menu.
● White Balance
Adjust the color temperature according to the environment automatically.
● AGC
Adjust the gain of amplifier, enabling the camera to output the standard video signal in different
lighting condition.
● Backlight Compensation (BLC)
When the back of the captured object is too much bright, you can set BLC for the captured object to
make it clearer.

● Backlight Compensation (BLC)
When the back of the captured object is too much bright, you can set BLC for the captured object to
make it clearer.
Cables
Power Cable
Video Output
Video Switch Cable
Video Switch: Four video output modes can be optional--AHD, TVI, CVI and CVBS
(a) remove the cover of the video switch cable; (b) hold and press the button in the video
switch cable for 5 seconds to switch the current video output.
2
Before you start, please make sure that the wall or ceiling is strong enough to wi ths tand three times
the weight of the camera. Please install and use the camera in the dry environment.
You’d better install back the lens cover or lower dome less than 4 hours after removing it.
The mounting types of cameras are only for reference.
Installation
►Mounting for VLD9
1. Drill the screw holes and the cable hole on the wall according to the drill template.
74.3
74.3
(mm)

3
2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove
the trim ring from the gap of the camera.
Rubber plug
Lower dome
* Install it when routing the
cables through the ceiling.
3. Loosen the screws to open the lower dome. Then route and connect the cables.
4. Secure the camera to the wall with screws provided as shown below.
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then
adjust the camera according to the figure below to get an optimum angle.
Rotation 0°~355°
Pan 0°~355°
Tilt 0°~67°
6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower
dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.
Trim ring

Gap
Microphone

4
∅4.6
90.2mm
90.2mm
►Mounting for VLD9M
1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove
the trim ring from the gap of the camera.
Rubber plug
Lower dome
* Install it when routing the
cables through the ceiling.
3. Loosen the screws to open the lower dome. Then route and connect the cables.
4. Secure the camera to the wall with screws provided as shown below.
Gap
Trim Ring
Microphone

5
6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower
dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.
Turn
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then
adjust the camera according to the figure below to get an optimum angle.

6
Specifications
Camera
Image Sensor
Resolution
Image size
Video Output
Image System
Electronic Shutter
IR Range (feet)
Frame Rate
Min. Illumination
Lens
Lens Mount
S/N Ratio
Ingress Protection
Functions
Function Control
Day & Night
WDR
Digital NR
AGC
Auto White Balance
HLC
BLC
LSC
Mirror
Privacy Mask
Smart IR
Sharpness
Image Setting
Defect Correction
Others
Power Supply
1/2.8" CMOS
2MP
1920×1080
AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)
NO
PAL/NTSC
33~66 65~98
30fps(60Hz); 25fps(50Hz)
0.001lux @F1.2, AGC ON; 0 lux with IR
2.8 mm 2.8~12 mm，motorized
M12 D14
≥ 52dB(AGC OFF)
IP 67 & IK10
OSD (UTC control)
ICR
120dB
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Auto
DC12V (± 10%)
IR OFF: < 1W; IR OFF: < 1W;
Specifications
Models VLD9
Power Consumption
Dimensions (inch)
Working Environment
IR ON : < 4W IR ON : < 6W
-22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)
Ф5.61 3.95×
Ф4.72 3.45×
VLD9M

Model: VLD9 /VLD9M
Federal Communications Commission (FCC) Statements
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
FCC Responsible Party:
Speco Technologies
200 New Highway
Amityville, NY 11701
www.specotech.com