Speco O2MT61B User manual

O2MT61
Owner’s Manual
O2MT61
Full HD Mini-Turret IP Camera

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
2
Caution
Any changes or modifications in construction of this device which are not explicitly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Directions
Be careful not to cause any physical damage by dropping or throwing the camera. Especially
keep the device out of reach from children.
Do not disassemble the camera. No after service is assumed when disassembled.
Use only power adapters compatible with the unit.
Be careful to prevent moisture or water penetration into the unit. Particular attention is
needed when installing the unit. The screw holes for the installation screws and pipe should
be maintained water tight during the whole life time of the product.
All the electrical connection wires running into the unit should be prepared so that water from
the outside cannot flow into the unit through the surface of the wires. Penetration of the
moisture through the wire for extended period can cause malfunction of the unit or
deteriorated image.

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
3
Revision History
Date
Revision
Details
Mar 4th, 2014
1.0
First manual revision creation.
Mar 7th, 2014
1.1
Text revisions
Apr 25th, 2014
1.2
Modified “2.3.3. Front and Rear view of Encoder box”

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
4
Contents
1. Introduction....................................................................................................................................................5
1.1. Overview...................................................................................................................................................5
1.2. Specifications............................................................................................................................................6
1.3. Applications of O2MT61 ...........................................................................................................................7
2. Product Description ......................................................................................................................................8
2.1. Contents ...................................................................................................................................................8
2.2. Product Preview........................................................................................................................................8
2.3. Physical description..................................................................................................................................9
2.3.1. External View..................................................................................................................................9
2.3.2. Dimensions.....................................................................................................................................9
2.3.3. Front and Rear view of Encoder box............................................................................................10
2.3.4. Factory Default Switch .................................................................................................................10
2.4. Functional Description............................................................................................................................11
3. On Site Installation ......................................................................................................................................13
4. Getting Started.............................................................................................................................................14
4.1. PC Requirement.....................................................................................................................................14
4.2. Quick Installation Guide..........................................................................................................................14
4.2.1. Connect PC and O2MT61 to network. .........................................................................................14
4.2.2. Install Speco-NVR and set IP parameters on O2MT61 ...............................................................15
4.2.3. Remote video connection to O2MT61..........................................................................................17
4.2.4. Additional settings through connection to the Admin Page..........................................................19
5. Trouble Shooting.........................................................................................................................................20
5.1. No power is applied................................................................................................................................20
5.2. Cannot connect to the Video ..................................................................................................................21
5.3. Windows Vista or Windows 7 .................................................................................................................22
5.4. Technical Assistance...............................................................................................................................25
AppendixA–ImportantNotice inExchangingSD Card(Micro SD).........................................................................26

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
5
1. Introduction
1.1. Overview
The O2MT61 is a full HD mini bullet IP camera with a separate encoder box. It is a multi-codec (H.264, MJPEG)
IP camera (or network camera) built with embedded software and hardware technology. It enables real time
transmission of synchronized video of up to 1080P and audio data. Remote clients can connect to O2MT61 for
the real time video/audio data through various client solutions running on PC or smart device. Real time 2-way
communication is available through the bidirectional audio communication feature.
Designed to be a stand-alone streaming audio & video transmission device, O2MT61 can be applied to various
applications such as video security, remote video monitoring, distance education, video conference or internet
broadcasting system.
The separate encoder box and camera design allows for smaller camera housing and flexibility in installations.
The camera portion is vandal and weather resistant, which allows it to be installed in outdoor settings, while the
encoder box can be hidden from view. Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the
owner to reduce the total cost of ownership by reducing on-site wiring works for the installation.

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
6
1.2. Specifications
Camera
Image sensor
Progressive scan 1/2.7 inch CMOS 2.0M pixels
Full resolution
1,920 x 1,080 pixels (Full HD)
Min. illumination
Color : 0.12 Lux (F1.4)
S/N Ratio
39dB or more
White Balance
AWB
DSS
Supported
WDR
Supported
Lens
3.7mm, F2.5
Day & Night
N/A
Video
Compression method
Simultaneous Dual Codec (H.264 / MJPEG)
Resolution
1,920 x 1,080@30fps
Multi-Profile Streaming
- 5 simultaneous video profiles
- Select the codec type, resolution and frame rates for each profile.
Intelligent Bit-Rate Control
VBR or CBR
PTZ
Digital PTZ & Video crop
Image Setting
Text overlay, Privacy mask, De-interlace filter
Motion detection
3 regions
Audio
Mono Upstream
32Kbps G.726 ADPCM, 64Kbps 16bit μ-law PCM ~ MIC/Line-in
Mono Downstream
64Kbps 16bit μ-law PCM ~ Line-out
Network
Network Protocol
- IPv4, TCP, UDP, IGMP, ICMP, ARP, RARP, PPPoE, RTCP
- RTP, RTSP, SDP, HTTP, SMTP, FTP, DHCP, UPnP
- NTP, DNS, DynDNS
Dynamic IP
Speco DDNS (free of charge)
Security
- User ID & Password protection, IP address filtering
- Digest Authentication, User Access Log
Streaming method
- RTSP streaming with proprietary format for control informations
- standard RTSP streaming
- HTTP streaming

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
7
External Terminals
LAN
10/100BaseT LAN (auto MDIX)
Alarm input / output
Alarm I/O (1 Sensor input & 1 Relay output)
Factory Reset
Supported
Audio
MIC/Line in, Line out
Power
DC 12V input
Alternate Power
Standard PoE
IEEE802.3af Supported
Alarm & Event
Intelligent Video
Motion Detection
Alarm Triggers
Intelligent Video + Sensor Input
Alarm Events
Video file upload(FTP), Still Image transmission(Email), Relay output
Alarm Buffer (Audio/Video)
Configurable Pre-alarm (5~15 sec) & Post-alarm (10~60 sec)
Client Software
Speco NVR
Windows XP/Vista/7 (free of charge)
Speco ONSIP
Android™, iPhone® , iPad® (free of charge)
Miscellaneous
Operating Temperature
0C ~ 45C (32F~113F)
Operation Humidity
8~80% RH
Power
DC 12V, 0.5A
Dimensions(W x H x D)
Camera : Ø 54.5mm x 48mm
Encoder : 45.6mm x 25mm x 114mm
Weight
Camera : 115g
Encoder Box: 115g
Casing
AL, PC, Vandal resistant, IP66 (camera portion only)
Approvals
FCC, RoHS
Package information
Unit, CD, mounting screws
1.3. Applications of O2MT61
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
Weather and environmental observation

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
8
2. Product Description
2.1. Contents
The product package contains followings :
Contents
Description
Remarks
O2MT61
O2MT61 main unit
Accessories
5m Video Cable 1EA, Screws, Anchors
L-type wrench with six angles
CD
Software & User’s Guide
Quick Reference Guide
Quick installation guide
2.2. Product Preview
O2MT61
ONSIP Installer
VMS Software (Speco NVR)
Camera Module &
Encoder Box
PC software to allocate an IP
address to the IP Camera
PC software to view and record the
A/V streaming data transmitted from
IP camera.
(Simultaneous support of up to 64
IP cameras@D1)

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
9
2.3. Physical description
2.3.1. External View
Figure 2-1. External view of O2MT61
2.3.2. Dimensions
Figure 2-2. Dimensions
Unit : mm

O
O2 2M MT T6 61 1 U Us se er r’ ’s s G Gu ui id de e
Rev.1.2 (Apr. 2014)
10
2.3.3. Front and Rear view of Encoder box
Figure 2-3. Front view
Figure 2-4. Rear view
Pin
Description
1
Line Output
2
Ground
3
MIC/Line Input
4
Relay Output
5
Relay Output
6
Sensor Input (-)
7
Sensor Input (+)
HDMI
Connect Camera Module
2.3.4. Factory Default Switch
Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover to
access the switch. There are two functions assigned to factory default switch.
1. Returning to Factory Default State : Press the switch about 5 seconds while power is applied to
return to factory default state.
2. Safe Removal of Micro-SD Card : Press the switch for 1 second to unmount Micro-SD Card for safe
removal.
Figure 2-5. Factory Default switch and Micro-SD Card slot
Factory Default Switch
Micro SD Card slot