Spectrum Controls WebPort WP-R-3G-SW-0 User manual

Internet
Internet
Internet
PC
1OR
Quick Start
2
3 4
Models Covered: WP-R-3G-SW-0, WP-ET-SW-0, WP-R-3G-SW-I
What’s Next? See the other side to register your WebPort to the cloud.
Questions? Access our built-in online help.
Required from User: • Internet connection (for WAN connectivity)
• SIM card from cellular provider and cell antenna (for cellular connectivity)
• 24 VDC power supply
• All cables and wiring
Spectrum Controls, Inc. | 1705 132nd Ave NE | Bellevue, WA 98005 USA | www.spectrumcontrols.com Copyright ©2017 Spectrum Controls, Inc., All rights reserved. Part No. 0100169-07 Rev A Revised 5/2017
For Internet
Connections
via Ethernet:
Connect PC to LAN Port
Connect Power Supply Log In to WebPort
For Internet
Connections
via Cellular:
Connect an Ethernet cable from
the WAN port to your Internet service
Insert a SIM
card from
your cellular
provider
To optional
wide area
disconnect
Common
+24 VDC
Ground
Screw your
antenna into
place or
connect a
cable to a
remote
antenna
Connect an Ethernet cable
from the LAN port to your PC.
Do not connect to the WAN port.
Your LAN IP address
will scroll across the
dot matrix display.
Type your LAN IP address into your browser.
Then, enter the default username and password.
Username: admin
Password: spectrum
Create a new password for your account.
Wire size: 22-14 gauge (2 mm) stranded
Tightening torque, min 0.22 Nm (2 in/lbs.)

5
9
8
76
10
NOTE: If you don’t have a Connects account, create a WebPort Connects
account at www.webportconnects.com.
Next, choose your account
from the dropdown menu.
After making your selection,
click Submit.
Registering WebPort Connects
Spectrum Controls, Inc. | 1705 132nd Ave NE | Bellevue, WA 98005 USA | www.spectrumcontrols.com
ATEX
Ex nA IIC T5 Gc
II 3G
DEMKO 11 ATEX 1103445X
Special condition for safe use (ATEX)
1. Provision shall be made to prevent the rated voltage being exceeded by transient disturbances of more than 140% of the peak
rated voltage.
2. The system shall be mounted in an ATEX certied enclosure with a minimum ingress protection rating of at least IP54, as dened in
IEC60529 of EM529 and used in an environment of not more than pollution degree 2. The enclosure shall be accessible only with
the use of a tool.
SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, AND D HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.
AVERTISSEMENT - RISQUE D’EXPLOSION - Ne déconnectez l’équipement tandis que le circuit est sous tension ou si la zone est connue pour étre libre de Concentrations inammables.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF ANY COMPONENT MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
DANGER D’EXPLOSION - La substitution de composants peut rendre cet équipement impropre á une utilisation en environnement de Classe I, Division 2.
Open the Configuration
dashboard at the top of
the screen.
Once you have clicked
the WebPort Connects
button, click on “Register WebPort.”
Register your account and Webport.
www.webportconnects.com
opens in your browser.
Enter your WebPort
Connects credentials.
Enter ID, WebPort
name, and other
information in the
WebPort dialog.
Then, click on the
WebPort Connects
button. Both the PC
and WebPort need
Internet access for
this step.
After entering your
information, click
Submit.
You are now a registered
member of the WebPort
family. To find out how to
connect to the cloud, set up
an alarm, configure a tag,
and much more, please visit
the context-sensitive help
located on your WebPort.
For more help, check out
our YouTube Channel at:
www.youtube.com/
WebportAcademy
You can access
context-sensitive
help at anytime by
clicking the online
help button on
your WebPort.