SpeeCo 40100500 User manual

This safety alert symbol identifies important safety messages in this manual.
Failure to follow this important safety information may result in serious injury or
death.
MODEL NO. 40100500
Owner’s Manual
ASSEMBLY& OPERATING INSTRUCTIONS
LS102-778-0608
Rev. 1
5 TON ELECTRIC
LOG SPLITTER

Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-6
Intended Use ......................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
General Safety ...................................................................................................................... 3
Safety Decals ....................................................................................................................... 2
Preparation of the Log ........................................................................................................... 3
Work Area ........................................................................................................................... 3
Operation of the Log Splitter .................................................................................................. 3
Repair and Maintenance Safety ............................................................................................. 4
Hydraulic Safety .................................................................................................................. 4
Fire Prevention ..................................................................................................................... 5
Transportation ...................................................................................................................... 5
Assembly Instructions ...................................................................................................................... 6
Operating Instructions ....................................................................................................................... 6-8
Directions for Filling Hydraulic System .................................................................................... 7
Storage ................................................................................................................................ 7
Operation .............................................................................................................................. 7-8
Maintenance ...................................................................................................................................... 8
Parts List ........................................................................................................................................ 9
Parts Breakdown Illustration ............................................................................................................... 10
Notes ................................................................................................................................................ 12
Warranty Information ........................................................................................................................... 12
Specifications .................................................................................................................................. Back Cover

NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only.Any other use can
cause serious injury or death.
PEPER
PERPERSONALSONAL PROTECTIVE EQUIPMENT
BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed shoes
and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device when operating this log
splitter.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away
from all moving parts when operating this log splitter.
WARNING: Read and thoroughly understand all instructions and safety information before assembling
or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone
to operate this log splitter who has not read this manual. As with all power equipment, a log splitter
can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts
or questions concerning safe operation. Call our customer service department at 1-800-525-8322 to
address these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
PERSONAL PROTECTIVE EQUIPMENT
DL-52-8
DL52-2-8
INTENDED USE
Page 1
GENERAL SAFETY
NEVER allow children to operate this log splitter.NEVER allow adults lacking proper instructions and understanding to
operate this log splitter.
KEEP all people and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the operator
is to be near the log splitter during use.
If a helper is assisting in loading logs, NEVER actuate the control until the helper is clear of the work area.
NEVER operate the log splitter when under the influence of alcohol, drugs or medication.
NEVER allow a person who is tired or otherwise not alert to use your log splitter.
ALWAYS unplug your log splitter when finished. Do not pull on power supply cable to unplug your log splitter.
Failure to follow these instructions may result in serious injury or death.

Page 2
SAFETY DECALS
Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals.
Write us or call 1-800-525-8322 and they will be sent to you at no charge.
LOCATION: SIDE OF BEAM, WEDGE END
PARTNUMBER: 52036900
Read and understand manual
before assembly and operation.
Always wear protective gloves.
Always wear protective shoes.
Always wear protective eye wear.
Caution: Do not touch rotating
parts.
Keep all people and pets away from
work area. Only the operator
should be near the log splitter
during operation.
Caution: Pinch Point
Warning: Moving parts. Never
place body between log and ram
during forward or reverse stroke.
Serious injury or death could result.
Never remove stuck log with bare
hands.
Always disconnect power supply
before performing maintenance,
cleaning, adjustments or moving
the log splitter.

ER
PREPARATION OF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 20 in. in length.
WORK AREA
NEVER operate the log splitter on slippery, wet, muddy or icy ground.
ONLYoperate your log splitter on a level surface. Operating on a slope could cause the log splitter to roll over or logs to fall
off.
NEVER operate your log splitter in a damp or rainy environment to avoid electric shock or short circuit.
ALWAYS block the wheels to prevent movement of the log splitter while in operation.
ONLYoperate your log splitter in daylight or under good artificial light.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble
over it.
OPERATION OF THE LOG SPLITTER
Page 3
ALWAYS enusre the motor is properly grounded or apply protection device. Only use rubber-jacketed cable of sufficient lead
cross section as an extension cable.
KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER place hands, feet or any body part between the ram and splitting wedge during forward or reverse stroke. Serious
injury or death could result.
NEVER straddle or step over the log splitter during operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a second log.
NEVER allow one person to operate the valve while another is positioning the log.
NEVER attempt to load your log splitter when the ram is in motion.
ALWAYS use your hand to operate the control lever and the switch. NEVER use your foot, a rope or any extension device.
NEVER move the log splitter while the motor is running. Shut off the motor even if you are leaving the log splitter for a short
period of time.

REPAIR AND MAINTENANCE SAFETY
NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.
ALWAYS unplug the power cable before performing any maintenance and repair.
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the width or
height of the wedge. Such alterations may cause your log splitter to be unsafe and will void the warranty.
Perform all recommended maintenance procedures before using your log splitter.
Replace all damaged or worn parts immediately.
NEVER tamper with the motor to run it at excessive speeds. The maximum motor speed is preset by the manufacturer and
is within safety limits.
NEVER adjust the hydraulic valve. The system is preset at the factory and is within safety limits.
ALWAYS check the level of hydraulic oil before operation.
ALL replacement parts must meet manufacturer’s specifications.
Page 4
HYDRAULIC SAFETY
The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked, cracked or otherwise damaged hydraulic hose and components.
NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or reaction
can develop if proper medical treatment is not administered immediately.
ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth
should it become necessary to loosen or remove any hydraulic fitting.
NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. Hot oil under pressure
could result in serious injury.
NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qualified
service technician should perform this adjustment.

FIRE PREVENTION
NEVER operate your log splitter near a flame or spark. Hydraulic oil is flammable and can explode.
ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measure against possible flying sparks.
Page 5
TRANSPORTATION
NEVER move this log splitter while the motor is running.
NEVER carry any cargo or wood on your log splitter.
NEVER allow anyone to sit or ride on your log splitter.
Be careful when moving your log splitter on rugged and rough terrain. Keep your log splitter upright.

ASSEMBLYINSTRUCTIONS
NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the
unit for repair or replacement of parts.
NOTE: Ensure the power supply is not connected while assembling the log splitter.
STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or
delivering carrier.
STEP 2: Connect the control handle bar. Align the control handle bar to its linkage part at the back of the log splitter and twist to tighten.
OPERATING INSTRUCTIONS
STEP 1: Preparation
WARNING: Read and thoroughly understand all instructions and safety information before operating
this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this
log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous
if assembled or used improperly. Do not operate this log splitter if you have doubts or questions
concerning safe operation. Call our customer service department at 1-800-525-8322 to address these
concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
IMPORTANT:The hydraulic tank is shipped with 10W hydrualic fluid. To use Dextron automatic transmission fluid, you must drain the system.
Do not mix Dextron and 10W hydrualic fluid.
CAUTION: DO NOT STARTOR RUN THE ENGINE WITHOUT OIL IN THE HYDRAULIC RESERVOIR AND IN
THE ENGINE.
Page 6
STEP 2: The hydraulic reservoir should be filled with 10W hydraulic oil. If hydraulic oil is difficult to obtain, Dextron automatic transmission fluid can be
substituted. Use only clean oil and take care to prevent dirt from entering the hydraulic reservoir. Do not mix 10W hydrualic fluid with Dextron
transmission fluid. Log splitter is shipped with 10W hydraulic oil, drain system if you wish to use Dextron transmission fluid.

DIRECTIONS FOR FILLING HYDRAULIC SYSTEM
1) Disconnect the control hand bar from its linkage part and take off the
cushions from the front frame.
2) Lift the towing handle and keep the tank in the vertical position.
3) Disconnect the vent plug and dipstick from the front cylinder cover.
4) Put the front frame of the unit in some container; raise the wheels 2 in.
off the ground on blocks, and drain the hydraulic tank.
5) Refill the tank within the marked range on the dipstick.
6) After refilling, insert and tighten the vent plug and dipstick.
Fill the hydraulic reservoir with at least 3 quarts of hydraulic fluid. After the hydraulic reservoir is filled with oil, start the motor. The hydraulic pump should
prime itself. With the motor running, move the hydraulic valve lever toward the wedge. This will cause the cylinder to extend and expel air. When the
cylinder is fully extended, retract it. Repeat this procedure several times.An erratic movement of the cylinder indicates that there is still air in the system.
More oil should then be added to bring the fluid level up to the “OK” range on the dipstick. Total hydraulic capacity is 3.3 quarts. NOTE: If the tank is
overfilled, it will tend to expel oil from the breather cap when the cylinder is retracted. After adding more oil to the tank, cycle the cylinder again until it has a
constant speed indicating that all oil has been expelled. Check the oil level in the reservoir again to make sure it is in the “OK” range.
Page 7
STORAGE
Store the log splitter switched off and unplugged.
Allow the log splitter to cool for 5 minutes after use before storing.
Protect the power supply cable from heat, sunshine, agressive liquids and sharp edges.
Store unit in a clean, dry area. Don’t store it unprotected outdoors, next to corrosive materials or in damp environment.
Store this log splitter where children can not start it.
OPERATION
WARNING: ALWAYS WEAR SAFETY GLASSES, SAFETY GLOVES, SAFETY SHOES AND SUITABLE WORK CLOTHING WHEN
OPERATING THIS LOG SPLITTER. NEVER WEAR JEWELRY, NECKTIES OR OTHER LOOSE CLOTHING.
DANGER: KEEP HANDS AND FEET CLEAR OF RAM AND WEDGE AT ALL TIMES.

1) Place the log splitter on a sturdy, level surface.
2) Ensure the equipment is in safe working condition. Check all nuts, bolts and hydraulic fittings are tight. Check the switch, power cable and plug
are not damaged. Check that all safety shields are in proper position.
3) Check that the outlet’s main voltage and frequency match the data stated on the model plate (or “Technical Specifications” in this manual).
4) Plug in the power cable and switch on the motor. NEVER use an extension cord longer than 25 feet. Cord gage must be 14 or lower.
5) Place a log on the beam against the wedge. Make sure that the log is securely on the wedge and up against the beam. Logs should be cut wth
square ends and to a maximum length of 20 in. in advance. Always use extra care when splitting logs with unsquare ends.
6) Depress the control handle so that the cylinder will drive the ram into the log. Extend the cylinder until the log splits or to the end of its stroke. If the
log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.
IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump.
CAUTION: ALWAYS SPLIT THE LOG ALONG ITS GRAIN. IF SPLIT ACROSS THE GRAIN SOME TYPES OF WOOD MAY
BURST OR FLYOUT RESULTING IN INJURY.
CAUTION: IF THE LOG IS STUCK ON THE WEDGE, RELEASE BOTH HANDS AND UNPLUG THE POWER CABLE
IMMEDIATELY. KNOCK OFF THE LOG WITH AHAMMER. DO NOT USE YOUR HANDS.
7) When finished splitting log, switch the motor off and unplug the power cable.
NOTE: Switch off and unplug the power cable quickly if the machine is acting abnormal. Contact our customer service department at 1-800-525-8322
to address these concerns.
MAINTENANCE
1) Switch off and unplug power cable before performing any maintenance and repair.
2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will
cause severe damage to the pump.
3) If the wedge becomes dull or nicked, it can be sharpened. ALWAYS wear safety gloves while handling the wedge.
4) See also Repair and Maintenance Safety in the Safety Information section of this manual.
5) All replacement parts must meet manufacturer’s specifications.
NOTE: If the motor is overloaded for a long time, the thermal protector will disconnect the power of the motor. Contact our customer service department.
NOTE: Switch off and unplug the power cable quickly if the machine is acting abnormal. Contact our customer service department to address these
concerns.
Page 8

ECNEREFER
REBMUN NOITPIRCSED
ECNEREFER
REBMUN NOITPIRCSED
1 egdewhtiwknaT 44-93 ylbmessahctiwsyeK
2 maR 94-54 ylbmessaroticapaC
3 marfoetalpesaB 05 revocrebbuR
4 rehsawgnirpS 25-15 ylbmessarevocxobgnitcennoC
5 tlobdaehpanS 45-35 ylbmessadraobgniriW
6 renilnolyN 75-55 ylbmessarenetsafelbaC
7 retlifliO 85 gulpdnaelbacrewoP
8 ebutliO 56-95 ylbmessaetalpdneraerrotoM
9 gnirlaeS 66 noihsucemarfrotoM
01 tlobderoB 76 gnirkcehC
11 rednilycciluardyH 86 gnirlaesnotelekS
41-21 stundnatfahsnotsiP 27-96 ylbmessarevocraerpmuP
51 gnirpsgnitcarteR 37 gnisuohraeG
91-61 sgnirlaesdnanotsiP 57-47 noitcesraeG
12-02 gnirlaesdnakcitspiD 67 gnirlaesepahs-O
22 gnirlaesliO 77 sebutralunnadnuopmoC
32 gnirkcehC 18-87 ylbmessarevoctnorfpmuP
42 revocrednilyctnorF 88-28 evlavciluardyH
52 gulptneV 29-98 ylbmessaeldnahlortnoC
72-62 tlobgnoldne-2 59-39 ylbmessaemarferiT
82 rotomrofrevocnaF 69 eriT
03-92 gnirkcehcdnanaF 79 pilcgnirpS
43-13 ylbmessarevocrotomtnorF 001-89 ylbmessaeldarcgoL
53 gniraeB 401-101 ylbmessaemarftnorF
63 rotatoR 501 noihsucemarftnorF
73 gnisacrotoM 901-601 ylbmessaeldnahgniwoT
83 mottobxobgnitcennoC 211-011 ylbmessasdleihS
NOTE: Drawing and parts list are shown for reference only should it become necessary to disassemble the unit for repair or replacement of parts.
PARTS BREAKDOWN FOR 40100500 LOG SPLITTER
Page 9
TRAP
REBMUN NOITPIRCSED
DETALER
MELBORP
00736093 tiKlaeSevlaV evlavmorfkaelliO
00836093 tiKlaeSknaTciluardyH knatdnarevocrednilyctnorffonoitisopnoitcennocmorfkaelliO)A
.natdnaevlavcilaurdyhfonoitisopnoitcennocmorfkaelliO)B
00936093 tiKlaeSebuTliO ebutliofonoitisopnoitcennocmorfkaelliO
00046093 tiKlaeSkcitspiD kcitspidtalaestuonroW
00146093 ylbmessAleehW leehwdegamadronekorB
00246093 reniLnolyN marehtrednurenilnolyntuonroW

PARTS BREAKDOWN FOR 40100500 LOG SPLITTER
Page 10

Page 11
NOTES
Model No. ____________________ Serial No. _____________________________
Date of Purchase _______________ Place of Purchase _______________________
_______________________
_______________________
_______________________
IMPORTANT NOTICE
We, the manufacturer, reserve the right to change the product and/or specifications in this manual without notification.
The manual is for information usage only and the pictures and drawings depicted herein are for reference only.
WARRANTY
This log splitter is guaranteed to be free from defects for one full year from the date of purchase.
Do not return this product to the store for warranty issues or repair. Call 1-800-525-8322 for the location of the nearest
service center.
Record the information below for future reference.

SPECIFICATIONS
ECROFGNITTILPSMUMIXAM snoT5
TNEMERIUQERLACIRTCELE zH06/V011
TUPNIREWOP W0691
TUPTUOREWOP W0051
TNERRUCDETAR A21
DEEPSROTOM MPR0043
ELBACREWOP mm0.1G3
2
YTICAPACCILUARDYH strauQ3.3
EMITELCYC sdnoces41
HTGNELGOLMUMIXAM "02
RETEMAIDGOLMUMIXAM "9
ERUSSERPCILUARDYH aPM02
EKORTSREDNILYCMUMIXAM "2/1-02
EZISERIT "7
)HXWXL(SNOISNEMIDENIHCAM "81x"11x"4/1-83
THGIEW .sbl501