SpeeCo LS401221N User manual

ASSEMBLY& OPERATING INSTRUCTIONS
LS50-634-0508
Rev 4
MODEL NO. LS401216N
25 TON
THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES IN THIS MANUAL
Owner’s Manual
MODEL NO. LS401221N
22 TON
MODEL NO. LS401213N
28 TON
MODEL NO. LS401224N
34 TON
VERTICAL/HORIZONTAL
LOG SPLITTERS

Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-6
Intended Use ......................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
Safety Decals ....................................................................................................................... 1-2
General Safety ...................................................................................................................... 3
Preparation of the Log ........................................................................................................... 3
Work Area ........................................................................................................................... 3
Operation of the Log Splitter .................................................................................................. 3-4
Repair and Maintenance Safety ............................................................................................. 4
Hydraulic Safety .................................................................................................................. 5
Fire Prevention ..................................................................................................................... 5-6
Towing Safety ...................................................................................................................... 6
Assembly Instructions ...................................................................................................................... 7
Operating Instructions ....................................................................................................................... 7-9
Engine Oil Recommendations ................................................................................................ 8
Starting Instructions ............................................................................................................... 8
Towing .................................................................................................................................. 9
Operation .............................................................................................................................. 9
Maintenance ...................................................................................................................................... 9
Parts List for Models LS401221N, LS401213N, LS401216N and LS401224N .............................................10-11
Parts Breakdown Illustration ............................................................................................................... 12
Notes ................................................................................................................................................ 13
Specifications .................................................................................................................................. Back Cover

WARNING: Read and thoroughly understand all instructions and safety information before assembling
or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone
to operate this log splitter who has not read this manual. As with all power equipment a log splitter
can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts
or questions concerning safe operation. Call our customer service department at 1-800-525-8322 to address
these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only.Any other use can
cause serious injury or death.
PEPER
PERPERSONALSONAL PROTECTIVE EQUIPMENT
BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed
shoes and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device when operat-
ing this log splitter.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away
from all moving parts when operating this log splitter.
PERSONAL PROTECTIVE EQUIPMENT
SAFETY DECALS
Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals.
Write us or call 1-800-525-8322 and they will be sent to you at no charge.
DL-52-8
DL52-2-8
INTENDED USE
Page 1
PARTNUMBER: 52020000
LOCATION: TOP, FRONT END OF TONGUE

Page 2
PARTNUMBER: 510105700
LOCATION: TOP, FORWARD SECTION
OF HYDRAULIC CYLINDER
PARTNUMBER: 51018900
LOCATION: TOP OF HYDRAULIC CYLINDER
PARTNUMBER: 52023200
LOCATION: HYDRAULIC TANK
LOWER TANK, RIGHT CORNER

GENERAL SAFETY
EVER
NEVER allow children or adults lacking proper instructions and understanding to operate this log splitter.
KEEP all people and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the
operator is to be near the log splitter during use.
If a helper is assisting in loading logs, NEVER actuate the control until the helper is clear of the work area.
NEVER operate the log splitter when under the influence of alcohol, drugs or medication.
NEVER allow a person who is tired or otherwise not alert to use your log splitter.
PREPARATION OF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 26 in. in length.
WORK AREA
NEVER operate the log splitter on slippery, wet, muddy or icy ground.
ONLYoperate your log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall
off.
NEVER operate your log splitter in an enclosed area. Exhaust fumes contain carbon monoxide which can be deadly when
inhaled.
NEVER attempt to move your log splitter over hilly or uneven terrain without a tow vehicle or adequate help.
ALWAYS block the wheels to prevent movement of the log splitter while in operation.
ONLYoperate your log splitter in daylight or under good artificial light.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble
over it.
OPERATION OF THE LOG SPLITTER
ONLY operate the log splitter from the operator zone.
TONGUE
ENGINE
BEAM
Page 3
Failure to follow these instructions may result in serious injury or death.
Operator
Zone

KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke. Serious injury or death
could result.
NEVER straddle or step over the log splitter during operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a second log.
NEVER allow one person to operate the valve while another is positioning the log.
NEVER attempt to load your log splitter when the ram or wedge is in motion.
ALWAYS use your hand to operate the control lever on the valve. NEVER use your foot, a rope or any extension device.
NEVER move the log splitter while the engine is running. Shut off the engine even if you are leaving the log splitter for a
short period of time.
ALWAYS avoid contact with the muffler and other hot areas of the engine during operation to prevent burns.
REPAIR AND MAINTENANCE SAFETY
NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the
width or height of the wedge. Such alterations may cause your log splitter to be unsafe and will void the warranty.
Perform all recommended maintenance procedures before using your log splitter.
Replace all damaged or worn parts immediately.
NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer
and is within safety limits.
ALWAYS remove the spark plug wire before performing any service or repair on your log splitter.
ALWAYS check the level of hydraulic oil and engine oil before operation.
ALL replacement parts must meet manufacturer’s specifications.
Page 4

HYDRAULIC SAFETY
The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked, cracked or otherwise damaged hydraulic hose and components.
NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or
reaction can develop if proper medical treatment is not administered immediately.
ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth
should it become necessary to loosen or remove any hydraulic fitting.
NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. Hot oil under pressure
could result in serious injury.
NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qualified
service technician should perform this adjustment.
FIRE PREVENTION
NEVER operate your log splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can explode.
NEVER fill the gas tank while the engine is hot or running. Allow the engine to cool before refueling.
NEVER smoke while operating or refueling your log splitter. Gas fumes can easily explode.
ONLYrefuel your log splitter in a clear area with no gas fumes or spilled gas.
ALWAYS use an approved fuel container.
ALWAYS replace the gas cap securely.
If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition
until the spilled gas has evaporated.
ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measure against possible flying sparks.
ALWAYS drain the fuel tank prior to storage to avoid the potential fire hazard.
ALWAYS store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place.
NEVER store gasoline in the house or near a heating appliance.
Page 5

IMPORTANT NOTE:
This log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark ar-
rester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in efffective
working order by the operator. In the state of California a spark arrester is required by law. Other states have similar laws.
Federal laws apply on federal lands. Aspark arrester muffler (optional by manufacturer) is available as an accessory at
your nearest engine dealer. Always check the legal requirements in your area.
TOWING SAFETY
ALWAYS check all local and state regulations regarding towing, licensing, and lights before towing your log splitter.
ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the towing vehicle
and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning. Always
use a Class I, 2” ball with this log splitter.
NEVER carry any cargo or wood on your log splitter.
NEVER allow anyone to sit or ride on your log splitter.
ALWAYS disconnect your log splitter from the towing vehicle before operating it.
ALWAYS be careful when backing up with your log splitter in tow. It could jackknife.
ALWAYS allow for added length of your log splitter when turning, parking, crossing interesections and in all driving
situations.
NEVER exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could result in
loss of control, damage to the equipment, serious injury or death. Adjust towing speed for terrain and conditions. Be
extra cautious when towing over rough terrain especially railroad crossings.
Page 6

EMBLYINSTRUCTIONS
NOTE: The following instructions pertain to four SpeeCo log splitters, the 22 ton (LS401221N), 25 ton (LS401216N), 28 ton (LS401213N)
and the 34 ton (LS401224N). The four models share most of the component parts.Any differences are noted in the parts list and assembly
instructions.
NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the
unit for repair or replacement of parts.
STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or
delivering carrier.
STEP 2: Attach the tongue (3) to the tank/axle (2) as shown in the diagram using the two 1/2 in. NC x 4-1/2 in. hex cap screws (48), 1/2 in.
lockwashers (47) and 1/2 in. NC hex nuts (46) from the hardware kit. Tighten. Make sure the ground stand (24) is in the vertical position.
NOTE: Flatwashers are included in the hardware kit should it be necessary to use them as spacers. This will eliminate play between the
tongue and the tank/tongue mounting plate.
STEP 3:
STEP 4: Stand the beam (1) up on end. NOTE: At least two people are required to raise the beam for the 28 ton and 34 ton models to insure
safety and prevent injury. Make sure that the beam is stable. Remove the pivot pin (52) and the clip pin (53) from the tank/axle (2). Roll
the axle/tongue assembly into position between the two tabs on the beam (1). Slide the pivot pin (52) through the holes and lock in place
with the clip pin (53).
STEP 5: Connect the end of the 1/2 in. I.D. x 47 in. (25, 28 & 34 ton models) or 1/2 in. I.D. x 44 in. (22 ton models) hydraulic hose (21) coming
from the fitting (20) on the pump (9) to the fitting (75) on the valve (5) .
STEP 6: Slide one hose clamp (50) on the end of the 3/4 in. I.D. x 37 in. (28 ton and 34 ton models) or 3/4 in. I.D. x 32-1/2 in.
(22 & 25 ton models) hydraulic hose (49) that comes from the fitting on the tank/axle (2). Then connect the hose to the fitting (69) on the
valve (5). Tighten the hose clamp.
STEP 7: If the optional fender kit (standard on the 34 ton model) was purchased, attach the fenders (44) to the tank/axle (2) using the 1/4 in. NC
x 3/4 in. hex cap screws (43), 1/4 in. flatwashers (42), 1/4 in. lockwashers (41) and 1/4 in. hex nuts (40). Tighten.
IMPORTANT: The engine and hydraulic tank are shipped without oil. See the engine operating and maintenance instructions manual packed with
your log splitter for the type of crankcase oil, fuel, etc. The engine manufacturer recommends lead-free gasoline only.
Page 7
Remove the rubber covering from the two spindles on the tank/axle (2). The wheel bearing cups, bearing cones, grease seals and
hub caps are already assembled. Bearing cones have been greased at the factory. Remove the blue, plastic protective covering from
the wheel hubs. Mount the wheels (54) to the spindles on the tank/axle (2) using the 3/4 in. light flatwasher (59) and 3/4 in. slotted nut (60)
from the hardware kit. There are two types of light flatwashers (59). Use the ones that best allow the wheel to rotate freely after the 3/4 in.
slotted nut (60) is tightened down and bearing play is removed. Install the cotter pin (61) and the hub cap (62) from the hardware kit.
Repeat step 4 for the other wheel.
WARNING: Read and thoroughly understand all instructions and safety information before operating this
log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log
splitter who has not read this manual. As with all power equipment a log splitter can be dangerous if it
is assembled or used improperly. Do not operate this log splitter if you have doubts or questions concerning
safe operation. Call our customer service department at 1-800-525-8322 to address these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
CAUTION: DO NOT STARTOR RUN THE ENGINE WITHOUT OIL IN THE HYDRAULIC RESERVOIR AND ENGINE.
ASSEMBLYINSTRUCTIONS
OPERATING INSTRUCTIONS

STEP 2: The hydraulic reservoir should be filled with an SAE 20 hydraulic oil. If hydraulic oil is difficult to obtain, automatic transmission fluid can
be substituted and should be used instead of hydraulic oil when temperatures are below 32 degrees F.Use only clean oil and take care to
prevent dirt from entering the hydraulic reservoir.
CAUTION: WHEN TIGHTENING THE BREATHER CAP ON THE TANK, POINT THE HOLE AWAY FROM THE ENGINE
AND THE OPERATOR ZONE.
ENGINE OIL RECOMMENDATIONS
1) 25 Ton, 28 Ton and 34 Ton Models- For temperatures above 40 degrees F use an SAE 30W oil. Using multigrade oil may increase oil
consumption. Using SAE 30W oil below 40 degrees F will result in hard starting and possible engine bore damage. For temperatures below
40 degrees F use an SAE 10W-30 or SAE 5W-30 oil. Oil capacity is about 1-1/2 quarts (48 ounces; 1.4 liters).
2) 22 Ton Model- For temperatures above 40 degrees F use an SAE 30W oil. Using multigrade oils may increase oil consumption. Using SAE 30W
oil below 40 degrees F will result in hard starting and possible engine bore damage. For temperatures below 40 degrees F use an SAE 10W-30
or SAE 5W-30 oil. Oil capacity is approximately 5/8 quart (20 ounces; 0.6 liter).
DIRECTIONS FOR FILLING HYDRAULIC SYSTEM
Fill the hydraulic reservoir with at least five gallons of hydraulic fluid (25 ton, 28 ton & 34 ton models). Use at least four gallons for the 22 ton model.
After the hydraulic reservoir and the engine crankcase are filled with oil, start the engine. The hydraulic pump should prime itself. With the engine
running, move the hydraulic valve lever toward the wedge. This will cause the cylinder to extend and expel air. When the cylinder is fully extended,
retract it. Repeat this procedure several times. An erratic movement of the cylinder indicates that there is still air in the system. More oil should then
be added to bring the fluid level up to the “OK” range on the dipstick. Total hydraulic capacities are as follows: 25, 28 and 34 ton models-31 quarts;
22 ton model-20 quarts. NOTE: If the tank is overfilled, it will tend to expel oil from the breather cap when the cylinder is retracted. After adding
more oil to the tank, cycle the cylinder again until it has a constant speed indicating that all air has been expelled. Check the oil level in the
reservoir again with the dipstick to make sure it is in the “OK” range. Do not fill beyond the “OK” range on the dipstick.
STARTING INSTRUCTIONS
Refer also to the Engine Operating and Maintenance Instructions manual for your particular log splitter.
1) 25 Ton, 28 Ton and 34 Ton Models with 10.5 h.p. Engine
a) Move the throttle lever to “FAST”. Always operate the engine with throttle lever in the “FAST” position
b) Move choke control lever to “CHOKE” position.
c) Grasp rope handle and pull slowly until resistance is felt. Then pull rapidly to start engine and avoid engine kickback.
d) Allow the engine to warm up. If operating in warm weather, move the choke control lever toward “RUN” a short distance at a time over
several seconds. For cold weather operation do this procedure over several minutes. Operate with choke lever in the “RUN” position.
e) To stop engine, move the throttle lever to the “STOP” position.
2) 22 Ton Model with 6.5 h.p. Engine and Primer
a) Move control lever to “FAST.”
b) Push primer bulb three (3) times.
NOTE: DO NOT USE PRIMER TO RESTART AWARM ENGINE AFTER ASHORT SHUTDOWN.
c) Grasp starter handle and pull rope out slowly until resistance is felt. Then pull rope rapidly with full arm stroke. Let rope return to starter
slowly.
d) When engine starts, leave the control lever at “FAST.” The throttle must be in the “FAST” position for maximum performance.
Page 8

STEP 3: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood, the throttle should
be set at the maximum setting to develop the horsepower required for the pump.
TOWING
The log splitter is equipped with pneumatic tires, a Class I coupler (2 in. diameter ball required) and safety chains. Before towing,
the safety chains must be secured to the hitch or bumper of the vehicle. Local regulations should be checked regarding licensing,
lights, towing, etc. Do not exceed 45 mph when towing this log splitter. See also Towing Safety on page 6 of this manual.
OPERATION
1) Set up the log splitter in a clear, level area and block the wheels. Make sure that the suction port on the tanks is always on the lower
side of the log splitter.
2) Place a log on the beam against the foot plate. Make sure that the log is securely on the foot plate and up against the beam.
3) Depress the valve handle so that the cylinder will drive the wedge into the log. Extend the cylinder until the log splits or to the
end of its stroke. If the log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.
IMPORTANT:Leaving the valve in the “actuate” position at the end of the stroke may damage the pump. Always use extra care
when splitting logs with unsquare ends.
NOTE: For operation in wooded areas, obtain a spark arrestor for the exhaust system. See the engine operating and maintenance manual
and check with your authorized Briggs & Stratton service center. See also Fire Prevention on page 5 and 6 of this manual.
IMPORTANT:TO EXTEND THE LIFE OF THE HYDRAULIC CYLINDER, AVOID “BOTTOMING OUT” WEDGE PLATE TO THE FOOT
PIECE. TO CONFORM WITH INDUSTRYSAFETY RECOMMENDATIONS, THE WEDGE STOPS 2 INCHES FROM
THE END OF THE STROKE.
MAINTENANCE
1) Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.
2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply
will cause severe damage to the pump.
3) Change the oil filter after the first 25 hours of operation. Thereafter, change the oil filter every 100 hours or seasonally, whichever comes first.
4) If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the 1/2 in. diameter bolt that connects the wedge to the
cylinder. The hose from the valve may need to be removed. While the log splitter is in the horizontal position, loosen the hose clamp and
disconnect the hose from the valve. Carefully lift the cylinder to allow the wedge to slide forward. The wedge can now be lifted off and
sharpened.
5) Clean the breather cap after 25 hours of operation. Clean it more often when operated in dusty conditions. To clean, remove the breather from
the tank and flush with kerosene or liquid detergent to remove the dirt.
6) See also Repair and Maintenance Safety on page 4 of this manual.
7) All replacement parts must meet manufacturer’s specifications.
Page 9
WARNING: See safety information related to operation of the log splitter on page 3 and 4 of this manual. Make sure that you have the
recommended personal protective equipment described on page 1.

Page 10
PARTS BREAKDOWN FOR LS401221, LS401216, LS401213 AND LS401224
LOG SPLITTERS
ECNEREFER
.ON .ONTRAP NOITPIRCSED
REBMUN
DERIUQER
0N422104 etelpmoCrettilpSgoLlatnoziroH/lacitreVnoT43
0N312104 etelpmoCrettilpSgoLlatnoziroH/lacitreVnoT82
0N612104 etelpmoCrettilpSgoLlatnoziroH/lacitreVnoT52
0N122104 etelpmoCrettilpSgoLlatnoziroH/lacitreVnoT22
1 0R214104 sledoMnoT43dnanoT82rof)"01x"8(maeB 1
0R114104 sledoMnoT52dnanoT22rof)"9x"6(maeB 1
2 0R204104 sledoMnoT43dnanoT82,noT52rofelxA/knaT 1
0R104104 ledoMnoT22rofelxA/knaT 1
3 00362104 eugnoT 1
4 0B711093 ledoMnoT43rofrednilyCciluardyH"42x"5 1
0B911093 sledoMnoT82dnanoT52rofrednilyCciluardyH"42x"2/1-4 1
0B811093 ledoMnoT22rofrednilyCciluardyH"42x"4 1
5 0S604093 sledoMnoT43dnanoT82,noT22rofevlaVnruteR-otuA 1
0A604093 ledoMnoT52rofevlaVnruteR-otuA 1
6 00814104 sledoMnoT43dnanoT82rofegdeW 1
00714104 sledoMnoT52dnanoT22rofegdeW 1
7 00425093 sledoMnoT43dnanoT82,noT52rofenignElaciremmoC/lairtsudnI.P.H5.01 1
00925093 ledoMnoT22rofenignE.P.H5.6 1
8 00106093 retliF 1
9 00907093 sledoMnoT43dna,noT82,noT52rofpmuPmpg61 1
0B507093 ledoMnoT22rofpmuPmpg11 1
01 0L428004 )seceip3(sledoMnoT43dna,noT82,noT52rofrelpuoCenignE-pmuP 1
0L528004 )edisenigne(sledoMnoT43dnanoT82,noT52rofflaHrelpuoC.D.I"1 1
0L628004 )edispmup(sledoMnoT43dnanoT82,noT52rofflaHrelpuoC.D.I"2/1 1
0L728004 sledoMnoT43dnanoT82,noT52rofredipSrelpuoC 1
00738004 ledoMnoT22rofrelpuoCenignE-pmuP 1
0L338004 )edispmup(ledoMnoT22rofflaHrelpuoC.D.I"2/1 1
0L838004 )edisenigne(ledoMnoT22rofflaHrelpuoC.D.I"8/7 1
0L438004 ledoMnoT22rofredipSrelpuoC 1
21 L/O )5edarG(wercSpaCxeH"1xCN"61/5 4
41 L/O tunkcoLCN"61/5 4
61 00343004 sledoMnoT43dnanoT82,noT52rofyeKenignEerauqS"4/1 1
00123004 ledoMnoT22rofyeKenignEerauqS"61/3 1
71 L/O sledoMnoT43dnanoT82,noT52rofwercSpaCxeH"2/1-1xCN"61/5 4
L/O ledoMnoT22rofwercSpaCxeH"2/1-1xCN"61/5 2
L/O ledoMnoT22rofwercSpaCxeH"2/1-2xCN"61/5 1
91 00842093 sledoMnoT43dnanoT82,noT52rofesoHnoitcuS"9x"1 1
00142093 ledoMnoT22rofesoHnoitcuS"8x"4/3 1
02 00143093 woblEteertSeergeD09x"2/1 1
12 00752093 sledoMnoT43dnanoT82,noT52rofesoHerusserPciluardyH"74x.D.I"2/1 1
00642093 ledoMnoT22rofesoHerusserPciluardyH"44x.D.I"2/1 1
22 00363093 sledoMnoT43dnanoT82,noT52rofgnittiFesoHeergeD09"1xTPN4/3 1
00023093 ledoMnoT22rofgnittiFesoHeergeD09"4/3xTPN4/3 1
32 00943093 elppiN"2/1-2x"4/3 1
52 00859070 dnatSdnuorGrofniPgnikcoL"61/5 1
62 L/O tloBmm58x5.1x01M 1
72 L/O rehsawkcoL"8/5 2
82 L/O tuNxeHFN"8/5 2
92 L/O tunkcoL5.1x01M 3
13 00908070 daerhTFN"8/5htiwniPretemaiD"8/7 1
23 00409070 niPhcnyL"4/1 1
33 00643004 llaB"2rofrelpuoChctiH 1
43 L/O rehsaWmm01 8
53 L/O tloBmm511x5.1x01M 1
63 L/O tloBmm001x5.1x01M 1
73 L/O kooH""S""htiwniahCytefaS 2

Repair Kits
HC390120F “O” Ring Kit for 4” x 24” Cylinder HC390118
HC390171 “O” Ring Kit for 4-1/2” x 24” Cylinder HC390119
HC390126 “O” Ring Kit for 5” x 24” Cylinder HC390117
HC390423 “O” Ring Kit for Valves HC390406A and HC390406S
HC390720B “O” Ring Kit for Pumps HC390705B and HC390709
Page 11
ECNEREFER
.ON .ONTRAP NOITPIRCSED
REBMUN
DERIUQER
93 L/O sledoMnoT43dnanoT82,noT52roftunkcoLCN"61/5 4
L/O ledoMnoT22roftunkcoL"61/5 3
04 L/O )lanoitpo(redneFroftuNxeHCN"4/1 4
14 L/O )lanoitpo(redneFrofrehsawkcoL"4/1 4
24 L/O )lanoitpo(redneFrofrehsawtalF"4/1 4
34 L/O )lanoitpo()5edarG(redneFrofwercSpaCxeH"4/3xCN"4/1 4
44 00151104 )sledomrehtollaroflanoitpo(ledoMnoT43rofredneF 2
54 00673093 sledoMnoT43dnanoT82,noT52rofkcitspiD 1
00573093 ledoMnoT22rofkcitspiD 1
64 L/O tuNxeHCN"2/1 2
74 L/O rehsawkcoL"2/1 3
84 L/O wercSpaCxeH"2/1-4xCN"2/1 2
94 00942093 sledoMnoT43dnanoT82,noT22rofesoHnruteRciluardyH"73x.D.I"4/3 1
00052093 ledoMnoT52rofesoHnruteRciluardyH"2/1-23x.D.I"4/3 1
05 00613093 61#pmalCesoH 4
25 CW220170 niPtoviP"4/1-6x"8/5 1
35 L/O niPpilC"R""8/1 1
45 0B213004 ylbmessAleehWdesaergerP 2
55 00671022 laeSesaerG 2
65 00571022 enoCgniraeB 4
75 00471022 puCgniraeB 4
95 L/O rehsawtalFthgiL"4/3 2
06 00021071 tuNdettolSFN"4/3 2
16 L/O niPrettoC"2/1-1x"8/1 2
26 00233004 paCbuH 2
36 L/O )5edarG(sledoMnoT43dnanoT82rofwercSpaCxeH"2/1-3x"2/1 1
L/O )5edarG(sledoMnoT52dnanoT22rofwercSpaCxeH"3x"2/1 1
46 L/O niPpilC 2
56 00137070 niPrednilyC 1
76 00743093 gnittiFebuT 2
86 00643093 ebuTleetSretemaiD"2/1 1
96 00023093 gnittiFeergeD09"4/3xTPN4/3 1
07 00343093 elppiNxeH"2/1-"2/1 1
17 00113093 gnihsuBrecudeR"2/1-"4/3 1
37 L/O tuNxeHCN"2/1 1
47 00471104 temmorG.D.I"4/1-1 1
57 00203093 eergeD09woblEleviwS 1
08 0A924093 evlaVrofeldnaHlortnoC 1
18 00434093 eldnaHevlaVrofkniLniahC 1
28 00244093 evlaVrofpaCgnirpS 1
00344093 evlaVrofylbmessAtneteD 1
38 00534093 evlaVroftekcarBgnitnuoM 1
48 00924070 niPsivelC"4/1 1
58 00011171 niPrettoCthgiartS"23/3 1
.serotsmrafdnaerawdrahhguorhtelbaliavasrenetsafnommoC.yllacolniatbO-L/O
PARTS BREAKDOWN FOR LS401221, LS401216, LS401213 AND LS401224
LOG SPLITTERS

Page 12
LS401221N, LS401216N, LS401213N AND LS401224N LOG SPLITTERS
Valve Assembly

Page 13
NOTES
Model No. ____________________ Serial No. _____________________________
Date of Purchase _______________ Place of Purchase _______________________
_______________________
_______________________
_______________________

SPECIFICATIONS
* Ideal case cycle times. Actual cycle times will vary depending on temperature, altitude, engine speed, pump efficiency, etc.
N122104SL.ONLEDOM N612104SL.ONLEDOM N312104SL.ONLEDOM N422104SL.ONLEDOM
GNITTILPSMUMIXAM
ECROF
snoT22 snoT52 snoT82 snoT43
ENIGNE
seireS056cc091
nottartS&sggirB
nottartS&sggirB.P.H5.01
laicremmoC/lairtsudnI
nottartS&sggirB.P.H5.01
laicremmoC/lairtsudnI
nottartS&sggirB.P.H5.01
laicremmoC/lairtsudnI
REDNILYC
ekortS"42XretemaiD"4 ekortS"42XretemaiD"2/1-4 ekortS"42XretemaiD"2/1-4 ekortS"42XretemaiD"5
EVLAV
nruteR-otuA nruteR-otuA nruteR-otuA nruteR-otuA
PMUP
mpg11egatS-owT mpg61egatS-owT mpg61egatS-owT mpg61egatS-owT
HTGNELGOLMUMIXAM
"62 "62 "62 "62
*EMITELCYC
sdnoceS41 sdnoceS21 sdnoceS21 sdnoceS51
SERIT
citamuenP"8X08.4 citamuenP"8x08.4 citamuenP"8X08.4 citamuenP"8X08.4
EGDEW
sgniWredaerpShtiwhgiH"7 sgniWredaerpShtiwhgiH"7 sgniWredaerpShtiwhgiH"7 sgniWredaerpShtiwhgiH"7
EZISMAEB
"9X"6 "9X"6 "01X"8 "01X"8
CILUARDYHLATOT
YTICAPAC
strauQ71 strauQ13 strauQ13 strauQ13
RETLIF
elbaecalpeRnO-nipS elbaecalpeRnO-nipS elbaecalpeRnO-nipS elbaecalpeRnO-nipS
THGIEH
noitisoPlacitreVni"27
noitisoPlatnoziroHni"24
noitisoPlacitreVni"27
noitisoPlatnoziroHni"24
noitisoPlacitreVni"27
noitisoPlatnoziroHni"24
noitisoPlacitreVni"27
noitisoPlatnoziroHni"24
HTGNEL
'87 "87 "87 "87
HTDIW
"94 "94 "94 "94
THGIEWGNIPPIHS
.sbl525 .sbl295 .sbl556 .sbl576