SpeeCo LS401227SP User manual

MODEL NO. LS401227SP
Owner’s Manual
ASSEMBLY& OPERATING INSTRUCTIONS
THIS SAFETYALERT SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES IN THIS MANUAL.
LS75-715-707
Rev. 2
22 TON VERTICAL/HORIZONTAL
LOG SPLITTER

Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-6
Intended Use ......................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
Safety Decals ....................................................................................................................... 1-2
General Safety ...................................................................................................................... 3
Preparation of the Log ........................................................................................................... 3
Work Area ........................................................................................................................... 3
Operation of the Log Splitter .................................................................................................. 3-4
Repair and Maintenance Safety ............................................................................................. 4
Hydraulic Safety .................................................................................................................. 5
Fire Prevention ..................................................................................................................... 5-6
Towing Safety ...................................................................................................................... 6
Assembly Instructions ...................................................................................................................... 7
Operating Instructions ....................................................................................................................... 7-9
Engine Oil Recommendations ................................................................................................ 8
Starting Instructions ............................................................................................................... 8
Towing .................................................................................................................................. 9
Operation .............................................................................................................................. 9
Maintenance ...................................................................................................................................... 9
Parts List ........................................................................................................................................ 10-11
Parts Breakdown Illustration ............................................................................................................... 12
Notes ................................................................................................................................................ 13
Specifications .................................................................................................................................. Back Cover

WARNING: Read and thoroughly understand all instructions and safety information before assembling
or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone
to operate this log splitter who has not read this manual. As with all power equipment, a log splitter
can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts
or questions concerning safe operation. Call our customer service department at 1-800-525-8322 to
addresstheseconcerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only. Any other use can
cause serious injury or death.
PEPER
PERPERSONALSONALPROTECTIVEEQUIPMENT
BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed shoes
andtight fitting gloves(withoutloose cuffsor drawstrings).Alwayswear a protectivehearingdevice when operatingthis log
splitter.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away
fromallmoving parts whenoperatingthis log splitter.
PERSONAL PROTECTIVE EQUIPMENT
SAFETYDECALS
Make sure that all safety warning decals are in good condition and readable.Always replace missing or defaced decals.
Write us or call 1-800-525-8322 and they will be sent to you at no charge.
PARTNUMBER:DL52-2-9
LOCATION:TOP, FRONTENDOFTONGUE DL-52-8
DL52-2-8
INTENDEDUSE
Page1
PARTNUMBER:DL52-2-8
LOCATION:TOP, FRONTENDOFTONGUE
PARTNUMBER:DL52-2-32
LOCATION:TANKLOWERRIGHTCORNER

PART NUMBER: DL51-1-57
LOCATION: TOP, FORWARD SECTION
OF HYDRAULIC CYLINDER
PARTNUMBER:DL51-1-32
LOCATION: TOP OF HYDRAULIC CYLINDER
Page 2
PARTNUMBER:DL52-2-14
LOCATION:TOP, FRONTENDOFTONGUE
PARTNUMBER:DL52-2-34
LOCATION: CLEVIS ENDOF BEAM
NEARTILTLOCKINGPIN

GENERALSAFETY
EVER
NEVER allow children tooperate this logsplitter. NEVER allowadultslacking proper instructionsandunderstanding to
operate this log splitter.
KEEP allpeopleand pets a minimum of 10 feetawayfrom your work area when operatingthislog splitter. Only theoperator
is to be near the log splitter during use.
If a helper is assisting in loading logs, NEVER actuate the control until the helper is clear of the work area.
NEVER operatethe log splitterwhenunder theinfluenceof alcohol, drugsor medication.
NEVER allow a person who is tired or otherwise not alert to use your log splitter.
PREPARATIONOF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 26 in. in length.
WORKAREA
NEVER operate the log splitter on slippery, wet, muddy or icy ground.
ONLY operate your log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall off.
NEVER operateyourlog splitter inanenclosed area. Exhaustfumescontain carbon monoxide whichcan be deadly when
inhaled.
NEVER attemptto move yourlog splitter overhilly or uneventerrain without atowvehicle oradequatehelp.
ALWAYS blockthe wheels topreventmovement of thelog splitter whileinoperation.
ONLY operate your log splitterindaylight or under good artificiallight.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble
overit.
OPERATION OF THE LOG SPLITTER
ONLY operatethe log splitter fromthe operator zone.
TONGUE
ENGINE
BEAM
Failure to follow these instructions may result in serious injury or death.
Operator
Zone
Page3

KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER placehands or feetbetween the logand splitting wedgeduring forward orreverse stroke. Seriousinjury or death
could result.
NEVER straddleor step overthe log splitterduring operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a second log.
NEVER allowone person tooperate the valvewhile anotherispositioning thelog.
NEVER attempt to load your log splitter when the ram or wedge is in motion.
ALWAYS useyour hand tooperatethe control leveronthe valve. NEVERuseyour foot, aropeor any extensiondevice.
NEVER movethelog splitter whiletheengine is running.Shutoff the engineevenif you areleavingthe log splitterfora short
periodof time.
ALWAYS avoidcontactwith the mufflerandother hot areasof the engineduring operation toprevent burns.
REPAIRAND MAINTENANCE SAFETY
NEVER operateyourlogsplitter when it is in poormechanicalcondition or in need of repair.
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the width or
height of the wedge. Such alterations may cause your log splitter to be unsafe and will void the warranty.
Performall recommendedmaintenanceprocedures beforeusing yourlogsplitter.
Replaceall damaged orwornpartsimmediately.
NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer and
is within safety limits.
ALWAYS removethe sparkplugwirebefore performinganyservice orrepaironyour logsplitter.
ALWAYS checkthe level ofhydraulic oil andengine oil beforeoperation.
ALL replacementparts must meet manufacturer’sspecifications.
Page4

HYDRAULICSAFETY
The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replacefrayed, kinked, crackedorotherwise damaged hydraulichose and components.
NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escapingfluid under pressurecanhave sufficientforceto penetrate skincausing serious personalinjury or evendeath.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
ALWAYS seekprofessional medical attentionimmediatelyif injured byescapinghydraulic fluid. Seriousinfectionor reaction
candevelop if propermedicaltreatment is notadministered immediately.
ALWAYS besure to relieveall pressure byshutting offthe engineandmoving thevalvecontrol handlebackand forth
should it become necessary to loosen or remove any hydraulic fitting.
NEVER removethe cap from thehydraulic tank orreservoirwhile the logsplitter is running.Hotoil under pressure
could result in serious injury.
NEVER adjustthe hydraulic valve.The pressurerelief valve onyourlog splitter ispreset at thefactory.Onlya qualified
servicetechnician should performthis adjustment.
FIRE PREVENTION
NEVER operateyour log splitter neara flame orspark.Hydraulic oil andgasolineare flammable andcanexplode.
NEVER fillthegas tank while the engine is hotorrunning.Allow theengineto cool before refueling.
NEVER smokewhileoperating or refuelingyour log splitter.Gas fumes can easilyexplode.
ONLY refuel your log splitter in a clear area with no gas fumes or spilled gas.
ALWAYS useanapprovedfuel container.
ALWAYS replace the gas cap securely.
If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition until the
spilledgas hasevaporated.
ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measureagainstpossible flying sparks.
ALWAYS drainthe fuel tankprior to storage toavoid the potential firehazard.
ALWAYS store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place.
NEVER storegasoline in thehouseor near aheating appliance.
Page5

IMPORTANTNOTE:
Thislog splitter is equippedwith an internalcombustionengine and shouldnotbe used onornear any unimprovedforest-
covered,brush-covered or grass-coveredland unless theengine’s exhaust systemis equipped witha spark arrestermeeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in efffective working order by the
operator. In the state of California a spark arrester is required by law. Other states have similar laws. Federal laws apply on
federallands.Asparkarrestermuffler(optional by manufacturer)is available asanaccessory at yournearest engine dealer
Always check the legal requirements in your area.
TOWINGSAFETY
ALWAYS check all local and state regulations regarding towing, licensing, and lights before towing your log splitter.
ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the towing vehicle
and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning.Always
use a Class I, 2” ball with this log splitter.
NEVER carryanycargo or wood onyourlog splitter.
NEVER allow anyone to sit or ride on your log splitter.
ALWAYS disconnectyour log splitterfrom the towingvehiclebefore operating it.
ALWAYS be careful when backing up with your log splitter in tow. It could jackknife.
ALWAYS allowfor added lengthofyour log splitterwhen turning, parking,crossinginteresections and inalldriving
situations.
NEVER exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could result
in loss of control, damage to the equipment , serious injury or death. Adjust towing speed for terrain and conditions.
Beextra cautious when towing overrough terrain especiallyrailroadcrossings.
Page6

ASSEMBLYINSTRUCTIONS
NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the
unit for repair or replacement of parts.
STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or
delivering carrier.
STEP 2: Attach the tongue (3) to the tank/axle (2) as shown in the diagram using the two 1/2 in. NC x 4-1/2 in. hex cap screws (48), 1/2 in.
lockwashers (47) and 1/2 in. NC hex nuts (46) from the hardware kit. Tighten. NOTE: Flatwashers are included in the hardware kit
should it be necessary to use them as spacers to eliminate play between the tongue and the tank tongue mounting plate.
STEP 3: Remove the rubber covering from the two spindles on the tank/axle (2).The wheel bearing cups, bearing cones, grease seals and hub
caps are already assembled. Bearing cones have been greased at the factory. Remove the hub cap (62) by prying it loose with a
common tip screwdriver. Mount the wheels (54) to the spindles on the tank/axle (2) using the 3/4 in. light flatwasher (59) and 3/4 in.
slotted nut (60) from the hardware kit.Tighten the nut until bearing play is removed and the wheel will still rotate freely. Install the cotter
pin (61) and hub cap (62). Repeat step 4 for the other wheel.
STEP 4: Stand the beam (1) up on end. Make sure that the beam is stable. Remove the pivot pin (52) and the clip pin (53) from the tank/axle (2)
Roll the axle/tongue assembly into position between the two tabs on the beam (1). Slide the pivot pin (52) through the holes and lock in
place with the clip pin (53).
STEP 5: Connecttheendofthe1/2in.I.D.x47in. hydraulichose(21)comingfromthefitting(20)onthepump(9)tothefitting(75)onthevalve
(5) port marked “IN.”
STEP 6: Slide one hose clamp (50) on the end of the 3/4 in. x 32-1/2 in. hydraulic hose (49) that comes from the fitting on the tank/axle (2). Then
connect the hose to the fitting (69) on the valve (5). This is the port marked “OUT” on the valve. Tighten hose clamp.
OPERATING INSTRUCTIONS
STEP 1: STARTING
WARNING: Read and thoroughly understand all instructions and safety information before operating
this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this
log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous
if assembled or used improperly. Do not operate this log splitter if you have doubts or questions
concerning safe operation. Call our customer service department at 1-800-525-8322 to address these
concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
IMPORTANT: Theengineandhydraulictankareshippedwithoutoil. Seetheengineoperatingandmaintenanceinstructionsmanualpacked
with the log splitter for the type of crankcase oil, fuel, etc. The engine manufacturer recommends lead-free gasoline only.
CAUTION: DO NOT START OR RUN THE ENGINE WITHOUT OIL IN THE HYDRAULIC RESERVOIRAND IN
THEENGINE.
Page7

STEP 2: The hydraulic reservoir should be filled with an SAE 20 hydraulic oil. If hydraulic oil is difficult to obtain, automatic transmission fluid can
be substituted and should be used instead of hydraulic oil when temperatures are below 32 degrees. Use only clean oil and take care to
prevent dirt from entering the hydraulic reservoir.
CAUTION: WHEN TIGHTENING THE BREATHER CAP ON THE TANK, POINT THE HOLEAWAY FROM THE ENGINE
AND THE OPERATOR ZONE.
ENGINE OIL RECOMMENDATIONS
For temperatures above 50 degrees F, use an SAE 30W oil. Using multigrade oil may increase oil consumption. For temperatures below 50
degrees F use and SAE 10W-30 oil. Using SAE 30W oil below 40 degrees F will result in hard starting and possible engine bore damage due to
inadequate lubrication. SAE 10W-30 is recommended for general use. Refer to Honda engine owner’s manual. Oil capacity is 0.58 quart
(19 ounces; 0.55 liter).
Always check oil level before starting the engine. Keep oil level at full.
DIRECTIONS FOR FILLING HYDRAULIC SYSTEM
Fill the hydraulic reservoir with at least five gallons of hydraulic fluid.After the hydraulic reservoir and the engine crankcase are filled with oil, start
the engine. The hydraulic pump should prime itself. With the engine running, move the hydraulic valve lever toward the wedge. This will cause the
cylinder to extend and expel air. When the cylinder is fully extended, retract it. Repeat this procedure several times.An erratic movement of the
cylinder indicates that there is still air in the system. More oil should then be added to bring the fluid level up to the “OK” range on the dipstick. Total
hydrauliccapacityis31quarts.NOTE:Ifthetankisoverfilled,itwilltendtoexpeloilfromthebreathercapwhenthecylinderisretracted.Afteraddingmore
oiltothetank,cyclethecylinderagainuntilithasaconstantspeedindicatingthatalloilhasbeenexpelled.Checktheoillevelinthereservoiragaintomake
sureitisinthe“OK”range.
STARTING INSTRUCTIONS
NOTE: REFER TO HONDAENGINE OWNER’S MANUAL FOR COMPLETE INFORMATION ON STARTING, MAINTENANCEAND TROUBLE-
SHOOTING.
ToStart aColdEngine
1) Turn the fuel valve to the ON position.
2) Move the choke to the ON position.
3) Move the throttle control to the FAST position.
4) Pull the starter grip lightly until resistance is felt. Then pull rapidly to start engine.
5) Move the choke lever to the OFF position if it was used to start the engine as soon as it warms up enough and is running smoothly.
6) When engine starts, move the throttle to the FAST position. It is recommmended that the engine be operated in the FAST position for
maximum performance.
To Start a Warm Engine
1) Move the throttle lever to the FAST position.
2) Pull the starter grip until the engine starts.
To Stop the Engine
1) Move the throttle lever to the SLOW position.
2) Move the throttle lever to the STOP position.
3) Turn the fuel valve to the OFF position.
Page8
NOTE: Theenginemaximumgovernedspeedispresetatthefactoryat3600RPMnoloadspeed.Whensplittingwood,thethrottleshouldbe
set at the maximum setting to develop the horsepower required for the pump.

1) Set up the log splitter in a clear, level area and block the wheels. Make sure that the suction port on the tank is always on the lower side
ofthelogsplitter.
2) Place a log on the beam against the foot plate. Make sure that the log is securely on the foot plate and up against the beam.Always use
extra care when splitting logs with unsquare ends.
3) Depress the valve handle so that the cylinder will drive the wedge into the log. Extend the cylinder until the log splits or to the end of its
stroke. If the log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.
IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump.
NOTE: For operation in wooded areas, obtain a spark arrestor for the exhaust system. See the engine operating and maintenance manual and
check with your authorized Honda service center. See also Prevent Fire in the Safety Information section of this manual.
NOTE: Output tonnage varies with altitude.
IMPORTANT: TO EXTEND THE LIFE OF THE HYDRAULIC CYLINDER,AVOID “BOTTOMING OUT” WEDGE PLATE TO THE FOOT
PIECE. TO CONFORM WITH INDUSTRY SAFETY RECOMMENDATIONS, THE WEDGE STOPS 2 INCHES FROM
THE END OF THE STROKE.
MAINTENANCE
1) Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.
2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will
cause severe damage to the pump.
3) Change the oil filter after the first 25 hours of operation. Thereafter change the oil filter every hundred hours or seasonally, whichever
comes first.
4) If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the 1/2 in. diameter bolt that connects the wedge to the
cylinder.The hose from the valve may need to be removed. While the log splitter is in the horizontal position, loosen the hose clamp and
disconnect the hose from the valve. Carefully lift the cylinder to alow the wedge to slide forward. The wedge can now be lifted off and
sharpened.
5) Clean the breather cap after 25 hours of operation. Clean it more often when operated in dusty conditions. To clean, remove the breather
from the tank and flush with kerosene or liquid detergent to remove the dirt.
6) See also Repair and Maintenance Safety in the Safety Information section of this manual.
7) All replacement parts must meet manufacturer’s specifications.
Page9
TOWING
Thelogsplitterisequippedwithpneumatictires,aClassIcoupler(2in.diameterballrequired)andsafetychains.Beforetowing,thesafetychainsmustbe
securedtothehitchorbumperofthevehicle.Localregulationsshouldbecheckedregardinglicensing,lights,towing,etc.SeealsoTowingSafetyinthe
SafetyInformationsectionofthismanual.
OPERATION
WARNING: ALWAYSWEARSAFETYGLASSESWHENOPERATINGTHISLOGSPLITTER.
DANGER: KEEPHANDSAND FEETCLEAROF RAM,STRIPPER PLATESAND BASEPLATEATALLTIMES.

Page10
PARTS BREAKDOWN FOR LS401227SP LOG SPLITTER
ECNEREFER .ON.ONTRAPNOITPIRCSED REBMUN DERIUQER
PS722104SLetelpmoCrettilpSgoLlatnoziroH/lacitreVnoT22
1S841104
SL)"9x"6(maeBrevliS1
2B091104SLelxA/knaTkcalB1
3362104SLeugnoT1
4B811093CHrednilyCciluardyH"42x"4kcalB1
5S604093CHevla
VnruteR-otuA1
6381104SLegdeW1
7235093CHenignEadnoH.P.H5.51
8106093CHretliF1
A106093CH )11egapnostnemeleretliftnelavi
uqefotsilees(tnemelEretliF1
B106093CHesaBretliF1
9B507093CHpmuPmpg111
01738004SL)seceip3(relpuoCenignE-pmuP1
L3380
04SL)edispmup(flaHrelpuoC.D.I"2/11
L438004SLredipSrelpuoC1
L838004SL)edisenigne(flaHrelpuoC.D.I"8/71
21L/O)5edar
G(wercSpaCxeH"1x"61/54
41L/OtunkcoLCN"61/57
61123004SLyeKenignEerauqS1
71L/O)5edarG(wercSpaCxeH"2/1-1xCN"61/53
91142
093CHesoHnoitcuS"2/1-8x"4/31
02143093CH09x"2/1
0
woblEteertS1
12852093CHesoHerusserPciluardyH"74x.D.I"2/11
22023093CH09"4/3xTPN"4/3
0
gnittiFesoH1
32943093CHelppiN"2/1-2x"4/31
42062104SLdnatSdnuorG1
528597PdnatSdnuorGrofniPgnikcoL"61/51
62817271WHtloB
mm58x5.1x01M1
72L/OrehsawkcoL"8/52
82L/OtuNxeHFN"8/52
92308271WHtuN5.1x01M3
13987PdaerhTFN"8/5htiwniP"8/5-2xretemaiD"
8/71
23497PniPhcnyL"4/11
33643004SLrelpuoChctiH"21
43809271WHrehsaWmm018
53717271WHtloBmm511x5.1x01M1
63617271WHtloBmm001
x5.1x01M1
73323004SLkooH"S"htiwniahCytefaS2
543004SLkooH"S""8/32
04L/O)lnwohston,anoitpo(redneFroftuNxeHCN"4/14
14L
/O)lnwohston,anoitpO(redneFrofrehsawkcoL"4/14
24L/O)nwohston,lanoitpo(redneFrofrehsawtalF"4/14
34L/O )nwohston
,lanoitpo(redneFrofwercSpaCxeH"4/3xCN"4/14
44151104SL)nwohston,lanoitpo(redneF2

O/L-Obtain locally.Commonfastenersavailable through hardware andfarmstores.
ReplacementFiltercartridge HC390601 interchanges with:
FRAM1653A
NAPA1553
Cross# 1A9023
Baldwin# BT839
Wicks # 51553
RepairKits
HC390171 “O” ring kit for 4-1/2 ” x 24” cylinder HC390119
HC390423E “O”ring kit forvalve HC390406S
HC390720B “O”ring kitfor pumpHC390705B
Page 11
ECNEREFER .ON.ONTRAPNOITPIRCSED REBMUN DERIUQER
54234004SLkcitSpiDegraL1
64L/OtuNxeHCN"2/12
74L/OrehsawkcoL"2/13
84L/Ower
cSpaCxeH"2/1-4xCN"2/12
94052093CHesoHnruteRciluardyH"73x.D.I"4/31
05613093CH61#pmalCesoH4
25CW22017PniPtoviP"4/1-
6x"8/51
35L/OniPpilC"R""8/11
45B213004SLylbmessAleehWdesaergerP2
5567122EBlaeSesaerG2
6557122EBenoCgniraeB4
7547122EBpuCg
niraeB4
85213004SLeriTdeepSdaoR"8x08.42
95L/OrehsawtalFthgiL"4/32
0602171NHtuNdettolSFN"4/32
16L/OniPrettoC"2/1-1x"8/
12
26233004SLpuCbuH2
36L/OwercSpaCxeH5edarG"2/1-3x"2/11
467397PniPpilC2
561377PniPrednilyC1
76743093CHgnittiFebuT2
86643093C
HebuTleetSretemaiD"2/11
96023093CH09"4/3xTPN"4/3
0
gnittiF1
07343093CHelppiNxeH"2/1-"2/11
17113093CHgnihsuBrecudeR"2/1-"4/31
27A924093CH)evlav(eldnaH1
434093CHeldnaHev
laVrofkniLniahC1
534093CHtekcarBgnitnuoMeldnaHevlaV1
37L/OtuNxeHCN"2/11
47471104SLtemmorG.D.I"4/1-11
57203093CH09wob
lEleviwS
0
1
551104SLtiKerawdraH1

Page 12
MODEL NO. LS401227SP LOG SPLITTER

Page13
NOTES
Model No. ____________________ Serial No. _____________________________
Date of Purchase _______________ Place of Purchase _______________________
_______________________
_______________________
_______________________

SPECIFICATIONS
*Ideal case cycle time. Actual cycle time will vary depending on temperature, altitude,
engine speed, pump efficiency, etc.
enignEadnoH.P.H5.5
pmuPmpg11,egatS-owT
rednilyCekortS.ni42xretemaiD.ni4
evlaVnruteR-otuA
ecroFgnittilpSmumixa
MsnoT22
htgneLgoLmumixaM.ni62
*emiTelcyCsdnoceS41
sleehWsmiRnoseriTebuTdeepS-daoR"8x08.4
egdeWsgniWredaerpShti
whgiH.ni7
eziSmaeBeldarCgoLnI-tliuBhtiw.ni9x.ni6
yticapaCciluardyHstrauQ02
retliFeniLnoitcuSniretliFelbaeca
lpeRnO-nipS
thgieH noitisoPlacitreVni.ni27 noitisoPlatnoziroHni.ni24
htgneL.ni87
htdiW.ni94
thgieWgnippihS.sbl
525